Search Documents

By J L. Carpenter, S M. Iveson, K P. Galvin

Wet beneficiation of iron ore fines less than 1 mm typically involves a desliming stage ahead of the fine gravity separation such as spirals. The desliming is achieved using a bank of cyclones. The reject ultra-fines emerge in the overflow stream at relatively low pulp density, contain high proportions of low-value slimes, but also well-liberated iron ore ultra-fines below 0.045 mm in size; however, recovering the valuable iron ore ultra-fines from this overflow stream presents a significant challenge due to the need to remove such a large amount of water and slimes.The REFLUX™ Graviton consists of distinct 3D-printed modular units, based on REFLUX™ Classifiers, which are rotated at high speed in a large centrifuge. This system has previously been investigated under semi-batch conditions, demonstrating the potential for precision separations with significant capacity. It has been shown that the throughput advantage of the inclined channels and G forces multiply. This is the first paper presented showing the performance of this system under continuous steady-state conditions. Ultra-fine silica in the size range of 0 to 0.045 mm was fed to the Graviton at different volumetric rates, fluidisation rates and pulp densities ranging from 2 wt per cent to 30 wt per cent, in order to develop a fundamental understanding of the system’s performance. Experiments were then repeated using ultra-fine iron ore.CITATION:Carpenter, J L, Iveson, S M and Galvin, K P, 2017. Separation of ultra-fine particles using the REFLUX™ Graviton, in Proceedings Iron Ore 2017, pp 141–148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Jacek Paraszczak

Numerous problems encountered in the mining of narrow vein deposits challenge the productivity, competitiveness and profitability of many mines. Mechanization of mining operations is one of the most important means to ensure the healthy survival of this mining sector. Vein deposits account for nearly all the world's primary silver production, as well as a significant portion of gold, tin, copper lead and zinc. In North America, narrow vein mining constitutes an important sector of the industry. Operators exploiting such deposits are concerned with the most appropriate mining method and equipment to mine in such a way as to minimize waste rock dilution. Unfortunately, most of the equipment available does not meet the additional geological and economical restrictions typical of narrow vein mining. Thus, mining these deposits is labor intensive and can result in low productivity. Consequently, the profitability of many such mines is reduced. Increased mechanization is one of the solutions to ensure their healthy survival. This paper reviews the state-of-the art in mining equipment with reference to narrow vein mining limitations. Problems encountered Geological conditions and economical factors have a decisive impact on the choice of mining method and equipment. Many ore bodies are relatively small, usually erratically distributed, often less than 2 m (6.5 ft) wide, with dips ranging from 0° to 90°. To make things worse, ore body limits are sometimes difficult to determine and the ground is hard and abrasive.

Jan 1, 1992

By C Chambers

"AustraliaÆs mining sector faces challenges to its competitiveness; operating costs are being adversely affected as a result of volatile commodity prices and growing international market pressures.Diesel fuel-generated power used in typical remote mining projects is generally reliable and quick-to-deploy; however it is ongoing expensive operating cost.Many mines and communities in remote locations source electricity from diesel generation, and often pay over $300/MWh in fuel and carbon only (i.e. excluding CAPEX). These costs are expected to rise over time and are vulnerable to price shock events or supply chain interruptions in international markets.Solar photovoltaic (PV) and other renewables can be integrated with existing diesel units to provide a highly reliable power supply. Such renewables now provide a cheaper source of electricity while maintaining the mining industryÆs stringent reliability requirements; some renewables are now cheaper than diesel power ù supplying electricity at approximately $226/MWh.Also, significant funding and concessional rate financing have recently become available to support the development of remote solar-diesel (or solar-wind-diesel) hybrid systems, including: up to $2.2 billion of as-yet uncommitted grants through the Australian Renewable Energy Agency (ARENA) and is now seeking mining industry partners, up to $10 billion of concessional financing for emerging renewable technologies through the Clean Energy Finance Corporation (CEFC) and this commences July 2013, ongoing revenue support through the Renewable Energy Target scheme, and other regional support programs administered by various governments.This paper explores: the business case for renewables - what applications and when to consider them, the potential operating cost savings if solar was integrated, the technical challenges and common pitfalls, and how to overcome them, and the upfront investment costs and whether the site is eligible for Government subsidy programs.CITATION:Chambers, C, 2013. Off-grid solar in the mining sector - Can renewable energy reduce your operating costs?, in Proceedings MetPlant 2013, pp 71-85 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

The structural design of a mine haul road involves the determination of cover thickness requirements above the in-situ or sub-grade material. The specification of these layerworks is a critical component in the overall road design process. Poor design often leads to premature failure of the road, safety is often compromised and productivity and equipment service-life will certainly decrease. Historically, the California Bearing Ratio (CBR) cover-curve design method has been widely applied to the structural design of mine haul roads. More recently, established mechanistic design principles have superceded the CBR approach to haul road design, using a multi-layer model to represent the various road structural layers. The structural design and associated layer thickness requirements are then determined following a maximum strain criterion. This paper develops a case-study evaluation of the CBR cover-curve and mechanistic design methodologies and through a comparative analysis of layerworks and materials, highlights how improved structural design can be achieved mechanistically.

Jan 1, 2011

By J. A. L. Campbell

The Galatia Mine is a dual-seam underground coal mine located in Saline County, IL. In 1984, it became the first coal mine to be permitted by the Illinois Department of Mines and Minerals to operate diesel equipment underground. And it is one of the larger underground coal mines in the nation to use diesel equipment. From the beginning, Kerr-McGee determined that diesel equipment offered the best approach to the safe and productive development and operation of the Galatia Mine. The flexibility of this equipment and its ability to promptly respond to changing conditions and mining locations made its use desirable for building this large dual-seam coal mine. The mine had a planned nominal annual capacity of 3.6 Mt/a (4 million stpy) and would employ more than 500 people. Galatia's current reserves are estimated at 231 Mt (255 million st) of recoverable coal from two seams of high-quality, high-volatile bituminous coal. The Harrisburg No. 5 seam is shipped primarily as a low-sulfur steam coal or as a metallurgical blend stock. It is also used in the pulverized coal injection (PCI) process for steel making. The Herrin No. 6 seam is a medium-sulfur coal. Annual production is shown in Fig. 1. A good indicator of a mine's success is employee productivity improvement. For many reasons - the proper use of diesel equipment, the introduction of longwalls and increased employee ex¬perience - Galatia employees have achieved a steady growth in annual productivity (Fig. 1) while maintaining an exceptional safety record.

Jan 1, 1993

By Jeffery L. Kohler

This final report on Bureau of Mines Contract J0338028 presents the results of a research effort to predict incipient failure in electric-power-system components. The development of continuous monitoring techniques to detect an incipient failure would represent a significant improvement in system maintainability, availability and safety, This report describes the analytical and experimental aspects of the project. Mathematical models have been developed to study the behavior of cables and motors which are undergoing a deterioration process. These models allow a detailed study of the effect of deterioration on the component's terminal characteristics and performance. The efficacy of using negative-sequence monitoring is a reliable indication of deterioration has been established. Techniques for assessing the sensitivity of the prediction algorithm to component deterioration have been presented. An approach for modelling electrically-excited vibrations, and including these in the algorithm, has been presented.

Jan 1, 1987

By A. J. Weinig

IN the accompanying figure consider the classified AB in closed circuit with a ball mill, wherein T = Tonnage of new feed C = Ratio of circulating load Now consider that the circulating load is made up of two portions of ore. One portion is due entirely to the characteristics of the ball mill and the tonnage of new feed impressed on the ball mill. This portion of the circulating load in no way is to be blamed on the characteristics of the classifier and is all composed of oversize. Consider, for illustration, that this portion of the circulating load is handled in the A division of the classifier, assuming that the classifier is divided longitudinally into two divisions by an imaginary line. Because the classifier does not usually make a perfect separation of the undersize, a certain portion of the total circulating load is to be directly blamed on the efficiency of the classifier. Let this portion of the circulating load be considered as being handled in the B division of the classifier. Now if the classifier is operating perfectly (100 per cent efficient), the width due to the B division becomes zero and correspondingly the efficiency of the classifier diminishes as B becomes wider in proportion to A. If E is the mechanical efficiency, then

Jan 1, 1934

By Louis A. Carapella, William E. Shaw

Magnesium and its alloys have long been characterized as possessing limited capacity for mechanical forming at atmospheric temperatures prior to rupturing despite their outstanding performances in this respect at elevated temperatures. Responsible for this behavior are the fundamental facts that these hexagonal-type metals have comparatively few slip elements at low temperatures for any extensive deformation and that, at high temperatures, additional slip elements become operative, thus enhancing greater plasticity under strain. The transitionai point has been set at 2 25°C by Schmidl for single crystals, and at 250°C by Morel1 and Hanawalt² for extruded magnesium metal. In a recent X-ray investigation on poly-crystalline magnesium-alloy sheets, Barrett and Haller3 have revealed that, below the transitional tempelature, the initial plastic deformation proceeds mostly by a twinning action; that, above such a temperature, the action is mostly by slip. The deep-drawing performance of the magnesium + 1.5 pct alloy sheet† over a wide range of temperatures has been investigated by Weber and Vanden Berg,' and their results are presented in Fig I. It should be noted from this work that a maximum drawability of about 25 pct at room temperature has been obtained on this alloy under the conventional deep-drawing operations. For the same alloy, it is now possible to augment the cold drawability to about 40 pct by a process to be disclosed. Hitherto, this value has been obtained only by deep-drawing the alloy at around 230°C. That greater plastic flow is attainable at atmospheric temperatures on magnesium under certain deformational techniques was discovered by the authors6 in their analyses of plastic-deformational behaviors of pure magnesium. This fact is best illustrated in Fig 2 from the Har-greaves analysis6 performed by the authors under two different modes of loading. For direct test, a separate unstrained specimen was used for each load duration, whereas for the integrated test the same specimen was employed for all the five intermittent loadings so that the load duration was made additive throughout the investigation. The higher plastic flow-rate at room temperature, as designated by the Har-greaves constant S, was obtained by the integrated or intermittent loading procedure. The authors6 in further tests showed that, under such a procedure greater plastic flow was also realized with a progressive increase in deformatione 1 loads. These findings have been applicd

Jan 1, 1947

By William E. Shaw, Louis A. Carapella

Magnesium and its alloys have long been characterized as possessing limited capacity for mechanical forming at atmospheric temperatures prior to rupturing despite their outstanding performances in this respect at elevated temperatures. Responsible for this behavior are the fundamental facts that these hexagonal-type metals have comparatively few slip elements at low temperatures for any extensive deformation and that, at high temperatures, additional slip elements become operative, thus enhancing greater plasticity under strain. The transitionai point has been set at 2 25°C by Schmidl for single crystals, and at 250°C by Morel1 and Hanawalt² for extruded magnesium metal. In a recent X-ray investigation on poly-crystalline magnesium-alloy sheets, Barrett and Haller3 have revealed that, below the transitional tempelature, the initial plastic deformation proceeds mostly by a twinning action; that, above such a temperature, the action is mostly by slip. The deep-drawing performance of the magnesium + 1.5 pct alloy sheet† over a wide range of temperatures has been investigated by Weber and Vanden Berg,' and their results are presented in Fig I. It should be noted from this work that a maximum drawability of about 25 pct at room temperature has been obtained on this alloy under the conventional deep-drawing operations. For the same alloy, it is now possible to augment the cold drawability to about 40 pct by a process to be disclosed. Hitherto, this value has been obtained only by deep-drawing the alloy at around 230°C. That greater plastic flow is attainable at atmospheric temperatures on magnesium under certain deformational techniques was discovered by the authors6 in their analyses of plastic-deformational behaviors of pure magnesium. This fact is best illustrated in Fig 2 from the Har-greaves analysis6 performed by the authors under two different modes of loading. For direct test, a separate unstrained specimen was used for each load duration, whereas for the integrated test the same specimen was employed for all the five intermittent loadings so that the load duration was made additive throughout the investigation. The higher plastic flow-rate at room temperature, as designated by the Har-greaves constant S, was obtained by the integrated or intermittent loading procedure. The authors6 in further tests showed that, under such a procedure greater plastic flow was also realized with a progressive increase in deformatione 1 loads. These findings have been applicd

Jan 1, 1947

By A Golsby

Although much talked about, social licence to operate (SLTO) is a relatively new concept that has been deemed as one of the four biggest business risks to a mining project over the life-of-mine. There is no accepted single definition of SLTO and this author understands SLTO to be stakeholder perception of the legitimacy of a project, a company or an industry. At a specific site, and across different sites within the same organisation, SLTO ranges through different levels according to stakeholders’ degrees of acceptance in time and space. Management of SLTO is vital for the mining sector but is difficult as it is informal and intangible. Although there are no key performance indicators, there are certain indicators that enable relative measurement of the ‘level’ of the SLTO. Because of the importance of the SLTO, information management during the entire life-of-mine, from exploration to rehabilitation, becomes crucial for the continued operation of a project. This paper identifies ten basic principles for the management of information to support the SLTO.CITATION:Golsby, A, 2014. Managing information to support a social licence to operate, in Proceedings Life-of-Mine 2014 , pp 389–398 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By Fernando Altamirano

Dado que en las unidades mineras existen problemas respecto al manejo de la información relacionada a la seguridad, salud e higiene tales como que los reportes enviados a las autoridades competentes (MEM, DGM, DGAA, OSINERG, DIGESA, etc.), se hacen en forma manual, generando una revisión y conteo previo tedioso y donde no existe una clasificación o estructuración de la información. En ese sentido, se plantea la utilización de las herramientas tecnológicas modernas para optimizar la administración de la información generada en las operaciones de forma diaria. Este sistema está desarrollado bajo una arquitectura Cliente/Servidor con bases de datos que soportan SQL., que se asegura una solidez en la generación de tablas relaciónales, un desarrollo práctico de las pantallas de entrada, flexibilidad para generar reportes y capacidad de expansión e integración a otras aplicaciones, donde se busca que el usuario se sienta a gusto utilizando su interfase full Windows diseñada para efectuar los registros y operaciones de manera intuitiva y versátil.

Aug 25, 2002

By Thomas Marcher

Stanford Linear Accelerator Center (SLAC) is located in Menlo Park, CA. In order to allow for enhanced experiments, the current facilities required expansion. Tunnels were excavated through very weak sedimentary rock interspersed with uncemented zones (Ladera Sandstone) employing the principles of the NATM. The overburden var-ied from 10 to 80 feet. The paper addresses the characterization of Ladera Sandstone that can exhibit the properties of dense sand and weak rock. The paper focuses on the challenges that were encountered during the NATM initial support design and the construction phase including the geotechnical instrumentation, monitoring and design verification process in particular the excavation of the junction between access tunnel and the FEH cavern (49 ft wide by 32 ft high).

By W. Robert Thompson

Hurricane Katrina caused significant damage to transportation structures on the Gulf coast in August, 2005, including the destruction of the US 90 Bridge over Biloxi Bay, Mississippi. Part of the successful design/build proposal for the replacement bridge included a comprehensive test pile program of indicator piles and load test piles in the geotechnical investigation program. A total of 22 indicator piles were installed on the project using the pile driving analyzer to monitor the pile behavior. Five load tests were performed: two axial Statnamic, two lateral Statnamic, and one static axial. The results of the test pile program established driving criteria for production piles that included end-of-drive blow counts and pile tip elevations with an appropriate allowance for setup. The program also confirmed that the planned installation equipment and techniques of GC Constructors, a joint venture of Massman Construction Co., Kiewit Southern Co., and Traylor Bros., Inc., would install the piles to the design tip elevations before production piles began. An extensive program of restrike measurements at a range of times after initial driving of the indicator piles provided a systematic documentation of pile setup in the soil profiles on the site. These resistance values were used to develop a dimensionless setup factor ?S? as the ratio of the restrike resistance to the end of drive resistance. This factor varied from 1.5 for piles penetrating clays and tipped in sand to 3.0 for piles bearing completely in clay and helped establish an end-of drive blow count that included an allowance for setup. The CAPWAP analyses of restrike data with setup and the load test data were used to confirm the design unit side shear and end bearing values developed from the borings and static capacity calculations and to select the design pile lengths.

Jan 1, 2009

By R. W. Raymond

On the Manchuria. SOMEWHAT fatigued with excess of enjoyment and strenuous continuity of movement on the trip to and through California, the members and guests of the Institute party embarked Tuesday, Oct. 17, on the Pacific Mail S. S. Manchuria for a further journey to and through Japan. The good ship displayed the flag of the Institute (blue cross-hammers on a white ground), together with the Stars and Stripes and the ensign of the company. Uninterrupted fair weather and smooth water attended the passage to Honolulu. The Manchuria proved herself most commodious, comfortable and clean ("A sweeter steamship never sailed," quoth President Hunt) ; Captain Dixon and his officers were most agreeable, as well as most efficient; the passenger list comprised many congenial people besides ourselves-among them a score of missionary folk, and also Mr. M. H. de Young, Vice-President of the Panama

Jan 1, 1912

By D. Vogt

South African underground hard rock mines are typically managed using measurements made daily, weekly or even monthly of key parameters such as face advance, readiness to blast, blast success, temperature or dust levels. Health, safety and productivity can all be greatly improved if a real-time measurement system can inform decision making. To enable this vision of widespread sensing, communication and decision support, CSIR has developed an open standard architecture for communication of sensor data, and a reference implementation using that standard. The standard, called AziSA, meaning ?to inform? in isiZulu, will allow any device that complies with it to join any network that supports it. The standard is designed for South African gold and platinum mines. To be practical in a typical Bushveld platinum mine, a real-time sensor system needs to be robust, reliable and cheap: ?Sensors are equipped with power sources that will last as long as the sensor is required. In effect, sensors need to be disposable: cheap enough not to warrant repair if they break. ?Communication in the stope is wireless, to avoid there liability problems associated with wire connections. For example, wires to sensors in the face area are unlikely to survive blasting. ?To get information out of the stope, the power line to the scraper winch is used as a communications link. Unlike a separate communications link, the power line will be repaired if damaged, because of its importance to production. ?Outside the stope, communications are transferred onto the mine communication infrastructure. To succeed as a management system, the next key element is the use of software decision support tools that will analyse masses of real-time data to extract key parameters and trends for decision makers. A range of sensors has been developed, including commercial sensors that have had wireless adapters added to make them AziSA compliant, and bespoke sensors that provide low cost sensing of typical mining parameters. An important parameter in any sensor network is the location of the sensor. This has to be easy and cheap to establish, so a tool has been developed to locate sensors in the confines of a stope, using ultrasonic and radio techniques. Once sensors are installed and located, they associate their location to all data that they produce. All the data from the system are captured at surface in a flexible database that can be queried by any application that requires data of any kind. It is simple to program alerts, and for actions to be associated with alerts. The use of wireless in stope also allows for communication from surface to the stope, or from stope to stope. The first implementation of an AziSA compliant system is being installed as part of the Mine Health and Safety Council funded rockfall elimination project. The design is discussed, and a future application for a platinum mine is considered.

Jan 1, 2009

By B. Anameric, S. K. Kawatra, K. B. Rundman

The iron nugget process is an economical, environmentally friendly, cokeless, single-step pig iron making process. Residence time dependent process requirements for production of pig iron nuggets at a fixed furnace temperature (1425 C) were investigated. Three chemically and physically different products were produced after complete reduction to iron, depending on the residence time in the furnace. These products were direct reduced iron (DRI), transition direct reduced iron (TDRI), and pig iron nuggets (PIN). The increase in the carbon content of the system as a function of residence time was detected by optical microscopy and Microhardness measurements. Sufficient carbon dissolution for the production of pig iron nuggets was obtained after 40 minutes residence time. The pig iron nuggets produced had chemical and physical properties similar to blast furnace pig iron. They were liquid state products and slag was completely separated from the metal.

Jan 1, 2005

By Richard E. Danell

"Blasting is a principal step in the surface mining process for breaking and, in the case of overburdencasting, moving rocks and minerals. As many surface mines are coming to the end of theiroperational life, blasting can once again play an important role through the earthmoving operationsrequired to rehabilitate the minesite. Since blasting is such an energetic and destructive process, itis difficult initially to envisage its use in rehabilitation. However, blasting has found applications inmany civil engineering projects aimed at rehabilitation, including well digging, channelling and soilcompaction. For surface mine rehabilitation, the main purpose of earthmoving operations is toproduce a stable landfonn that will sustain revegetation. In particular, blasting can be applied toreducing the slope of steep walls left by quarrying and open pit mining through a modified form ofthe overburden casting technique. Blasting can also be applied to breaking up pit floors andbenches to speed and improve revegetation of these areas (subsoiling)."

Jan 1, 1994

WITH the exception of the deposits of the Milburn Cement Co near Dunedin, Wilson's Portland Cement Co., on the Mahurangi River (a short distance north of Auckland), and those of the New Zealand Portland Cement Co., at Limestone Island, the cement. Tesources of New Zealand remain practically undeveloped. The Milburn Company utilizes a mixture of limestone and mud for the manufacture of cement, while Wilson's and the New Zealand Portland Cement companies both have the advantage of a natural cement stock which requires but small additions of highgrade limestone to give the mixture required. The plant and deposits of the New Zealand Portland Cement Co are located in Whangarei Harbour, some six miles from thetownship of Whangarei. The works and dwelling-houses are situated on Limestone Island, which, with an area of 92 acres, and rising to a height of 212 ft., supplies the bulk of the raw material required. In addition to the island, the company possesses a high-grade limestone area of, roughly, four acres, situated on the mainland, 11 miles to the south. A better location for a cement works could not well have been chosen. On the east side of the island there is a deep channel, which never shows less than 18 ft. of water alongside the company's...

Jan 1, 1912

By William J. Krisko

This contract final report summarizes the design, fabrication and testing of canopy air curtain devices under Bureau of Mines Contract H0232067. The canopy air curtain device is designed to reduce the level of respirable dust exposure to a continuous mining machine operator while having a minimum effect on operator safety, mobility and comfort and being compatible with mining equipment. This contract was devoted to the development of a device which utilizes an invisible curtain of air to envelope a mining machine operator's breathing zone with filtered air to provide respiratory protection. Various concepts were evaluated by means of laboratory tests. One concept was selected and was tested on various mining machines at underground sites by means of MSA personal samplers. The canopy air curtain was found to be effective. The percent reductions over the ambient dust concentrations were about 30 to 75 percent depending on the amount of time the operator spent under the air curtain. At one test site, the device enabled the mining machine to operate within compliance. Donaldson Company is presently working on the commercial production of the device.

Jan 1, 1975

By Jim Wickens, Vince Lofftus, Mark Kravetz

"This paper discusses how Bald Mountain Gold Mine (Ely, NV) dramatically reduced mercury production by treating process solutions with a liquid reagent based on organic sulfide chemistry. Cherokee Chemical Co. Inc. (Vernon, CA) markets this reagent as UNR 81 1A.A summary of the bench tests comparing various reagents is given. The ensuing plant trial is discussed and successful mercury removal results are presented. Data is presented to show that early removal of mercury in the process reduces the amount of mercury collected at retort. Data is also presented to show that use of this reagent does not reduce gold recovery. Plant trial treatment costs are discussed. Finally, the potential of this technology to substantially reduce closure costs as compared to traditional mercury removal options is discussed.INTRODUCTIONBald Mountain Mine produces gold. Mercury is a costly by-product of gold production because no revenue is generated from mercury. Traditionally, mercury leaches out with gold and follows the gold throughout the processing circuit until it is eventually condensed and collected at Retort. Minimizing or eliminating mercury production minimizes worker health and safety risks, minimizes environmental liability, and reduces costs. In the long term, minimizing mercury production will make mine closure easier and less costly.Bald Mountain Mine dramatically reduced mercury production by treating process solutions with liquid reagents called UNR 811 and UNR 811A. Several reagents were bench tested before proceeding with a plant trial. The reagent complexes the mercury to form an insoluble organic sulfide precipitate. In independent tests, the precipitate passed acid mobilization tests and is considered stable."

Jan 1, 2001