Search Documents

By A Kurniawan, A Sjadat and M Akhasyah

PT Freeport Indonesia’s Deep Ore Zone (DOZ) is a block cave mining operation that has been in production for 15 years. DOZ is located approximately 900 m below surface and has an average production rate of more than 5000 t/d. The footprint of the extraction level will ultimately be 900 m long and average more than 200 m wide. The undercut level is located 20 m above the extraction level.While developing Panel 1K on the northern portion of the extraction level, a major geotechnical problem was encountered when there was a change in lithology and an associated fault intersection. A large collapse of the hanging wall of the extraction level drifts occurred in the area of the fault intersection between February and March 2011. This was followed by a collapse of one of the undercut level drifts directly above the extraction level in May 2011.It was suggested that the best approach to mitigate risk during rehabilitation was to systematically open up the failed area under the protection of a steel set support system. To achieve this, approximately 60 t of grout was injected from the undercut level to fill the voids created when the rock mass between the two levels failed. A ground penetrating radar system was used to survey the condition of the rock mass between the two levels before and after the injection of grout. After the grout injection phase was completed to a satisfactory level of confidence, rehabilitation activities started on the extraction level by taking out the now consolidated material from inside the drift in 2 m advances from under steel sets initially constructed in secured ground.Controlled blasting was the key aspect to the success of the initiative to open up just enough of the drift to systematically support the rock mass before the next set was installed. The systematic support consisted of in-cycle shotcrete sprayed over mesh pinned to the exposed rock, as effectively as possible, with splitsets before spiling the next advance’s protection canopy with rebar. Once secure, a combination of steel set and pumped concrete was installed as the final support. This final support provided a safe platform to repeat the process until the failed zone was safely traversed.CITATION:Kurniawan, A, Sjadat, A and Akhasyah, M, 2016. Rehabilitation of the collapsed panel 1K north in the Deep Ore Zone block cave mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 763–768 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Jeremy Bosman, Johan de Korte

Traditionally the feed to coal preparation plants was de-slimed at 0,5 mm. The +0,5 mm size fraction was processed via dense-medium cyclones and the -0,5 mm size fraction was beneficiated with froth flotation, water-only cyclones or spirals. With the introduction of large diameter cyclones, the aperture sizes of de-sliming screens have progressively increased to about 3 mm in the belief that the larger cyclones are not able to effectively beneficiate coal which has a particle size below the ?breakaway? size. The efficiency of separation in the large dense-medium cyclones is improved by presenting a coarser feed to the units. At the same time, the capacity of the de-sliming screens is increased due to the larger screen apertures and in effect, the throughput capacity of the dense-medium section is increased. The 3 x 0,5 mm size fraction, which was previously processed in the dense-medium cyclones, is now added to the fine coal size fraction and processed by water-only methods such as Teetered Bed Separators (TBS) and spirals. Whether this practice is the most economical way to process the 3 x 0,5 mm size fraction requires further thought since the best processing route for the 3 x 0,5 mm size fraction will depend on a number of factors, amongst which are: o The washability of the coal and the amount of near-density material o Processing efficiency o Specification of the required product o The price paid by the customer for the product o The cost of processing the coal Breakaway size The ?breakaway? size is defined as the particle size below which the Epm of the smaller particles starts to decrease significantly. Bosman1 provides an approximate breakaway size versus cyclone diameter (Figure 1). It should be kept in mind though that the Epm of the small particles is a function not only of the cyclone diameter but also of feed pressure, medium density, medium viscosity, particle shape and density, top-size of particles in the feed, etc.

Jan 1, 2006

By Paul Staples, Chris Morley

"The development of the Cerro Verde, Amplats Mogalakwena and Boddington projects over the last few years has helped to establish the use of high pressure grinding rolls (HPGR) in comminution circuit designs in large-scale hard-rock applications. The increasing acceptance of this innovative and sometimes controversial technology has had the natural effect of prompting many other new projects to examine HPGR as an alternative to the established, usually SAG-based, comminution circuit design approach.At the current stage of development of the technology, HPGR-based circuit capital costs are generally higher than for the equivalent SAG-based circuit, so that HPGR must offer sufficient operating cost benefits to offset the additional capital costs over an acceptable pay-back period. It is usually necessary to undertake comprehensive project-specific trade-off studies to quantify this effect.This paper describes the processes involved in the execution of a typical SAG-HPGR trade-off study, from the preliminary assessment of ore characteristics and project criteria, through testwork, circuit modelling, equipment selection and cost estimates, to a project-economics comparative assessment of the options. The trade-off study determines both the technical feasibility of the respective technologies and their commercial viability in the given project setting.The paper concludes with a cautionary note to the effect that, while HPGR has many potential benefits, it is not a panacea, and that, for some ore types and project conditions, the more established conventional technologies are often more appropriate."

Jan 1, 2010

An active list of permissible explosives was published in July, 1931, as part of United States Bureau of Mines Report of Investigations 313, under the title of "Active List of Permissible Explosives and Blasting Devices Approved Prior to June 30, 1931." Changes in that list were authorized in August, September, October, November, and December, 1931, and. January and March, 1932, as published in Reports of Investigations 3l40, 3147, 3l50, 3155, 3158, 3161, and 3163, respectively. By these changes the following explosives were added to the active permissible list: [Austin Red Diamond No. 1, L. F. Gel-Coalite W. L. F. Austin Red-Diamond No. 5, L., F. Gen-Gel No. 2. Black Diamond Nu-Gel No. 1 Genite C-1 Burton 1, L. F. Liberty No. 4 Burton 2, L. F. Liberty No. 5 Burton 10, L. F. Peerless D Burton 12, L. F. Permigel 1, L. F. Burton F, L. F.]

Jan 1, 1932

By Richard I. Miller

Science Applications, Inc. has developed for the U.S. Bureau of Mines a rapid response radon monitor capable of accurately responding within three minutes to changing radon levels of magnitude from 100 to 10,000 pCi/1, typical of the levels in working uranium mines. The instrument weighs 17 pounds, is sized 12" x 10" x 6", and is capable of 8 hours of continuous portable operation with a self-contained, rechargeable battery power source. Residual chamber contamination from a radon level allowed to remain in the chamber for 90 minutes is about 10 percent, decaying about a factor of two in one hour. The instrument sensitivity is a nominal 0.1 cpm/(pCi/1), with a background count rate of less than 1 cpm.

Jan 1, 1979

Relatively few longwall mines in the U.S. operate under multiple seam conditions where the two seams are less than 200 ft apart. This paper describes the experience of six that do. These operations are located in PA, WV and UT, and include examples of both undermining and overmining. Some operate above or beneath their own workings, others are in historic mining districts and must contend with abandoned mines that are decades old. The lessons that these mines have learned cover a broad range of topics, including: • Whether to stack gateroads or place them under old gob areas; • How to size pillars and select artificial support to cross longwall stop lines; • How to use yield pillars to minimize multiple seam stresses and coal bump potential, and; • When to anticipate the creation of pathways for gas, water, or oxygen between current and abandoned gobs.

By S. Kitamura

In recent years, the amount of ferritic stainless steel production has increased. However, the rust formation by the salt spray test was pointed out in the past. At the centre of the circular rust zone, pitting corrosion where water-soluble nonmetallic inclusions were embedded was observed. These inclusions originated from the suspended refining slag and consisted of multi-phase oxides and sulphides. By the experiments and thermodynamic consideration of the water-solubility, not only CaO or CaS, but also lime rich calcium-aluminates or calcium-silicates have shown large water-solubility. The composition of oxide phase in the inclusions was almost the same among the samples from molten steel, slab, or cold rolled sheet. On the contrary, CaS was clearly observed around the oxide in the sample of cold rolled sheet, although it was not found in the molten steel or slab samples. The enrichment of sulphur occurred from the desulphurization reaction of the suspended slag particles in the molten steel and also occurred from the diffusion of sulphur to the oxide inclusions during the heating of the slab. The optimization of refining slag composition has lead to produce the ferritic stainless steel without rust formation. Keywords: stainless steel, rust, calcium aluminates, calcium sulphides, water-solubility, refining slag, composition control of inclusions.

By F. D. Wright, H. D. Fara

The solution to the plastic and elastic stresses around a circular shaft in a hydrostatic stress field that has appeared in two editions of a widely used book on rock mechanics1 is in error. Although this is a relatively minor matter, the correct solution was not found by a literature survey, so it appears worthwhile to present it. For a homogeneous, isotropic, rigid plastic-elastic body in plane strain which obeys Tresca's yield criterion the following equations must be satisfied:'," In the plastic zone,

Jan 1, 1963

By J P. Sykes, A Trench

"The common-held view of the future of copper mining is one of declining quality of mineral resources and increasingly limited long-term development options. This decline, in turn, is viewed as inevitably leading to increasing economic, socio-political and environmental costs. As a result, new technologies and innovations will be required to mitigate cost escalation. The future is therefore typically summarised as a battle of a ‘below-ground’ declining quality asset base pushing costs upward versus ‘above-ground’ technology and innovation driving costs downward. The role that high quality new mineral discoveries could play in mitigating industry cost pressures is typically understated, if considered at all. New high quality discoveries can be mined at lower cost than existing assets and potentially if discovered in the right locations within a more amenable contemporary environmental and socio-political setting. Such deposits, once discovered, would improve the overall quality of the industry asset base, as well as benefitting their owners substantially through higher margins. However, to target new high quality deposits explorers need some understanding of the nature of high quality copper mines in the long-term future. Conventional scientific and economic techniques for analysing the future of copper supply, generally by studying the project pipeline, ignore as yet undiscovered resources and also struggle to fully incorporate the multiple internal and external factors that could impact upon copper mining practices in the future.Scenario analysis is specifically designed to consider multiple factors interacting in the future, and is thus more creative than simply looking at the visible project pipeline. The use of scenarios is therefore potentially capable of providing insight into aspects of the future of copper mining about which little is currently known or that remains considerably uncertain. In this study, the Oxford University Scenarios methodology was employed to analyse different plausible futures for copper mining and the consequent implications for exploration targeting strategies. The scenario analysis highlights two key dimensions or axes that serve to map out potential industry futures: firstly the technical and economic optimisation of the existing industry; and secondly the generation of new prospects or ‘search space’ for the copper industry. These two axes in turn frame four different scenarios for the future of the copper mining industry. These copper mining scenarios are then compared to the 20 largest existing copper mines and projects, and their owners, to determine if any represent an appropriately robust exploration targeting proxy: none do. The paper therefore concludes that efforts by industry are required to generate mine concepts that would be viable across all scenarios, and thus act also as exploration targeting proxies. In the interim, companies will have to seek to build portfolios that create an overall robust asset base, out of individually less robust assets. Failure to do this implies that consequential, irreversible strategic decisions lie ahead for the copper mining industry, which may be a threat to both incumbents and the very industry itself. This situation makes strategic exploration targeting in the copper industry very difficult.CITATION:Sykes, J P and Trench, A, 2016. Using scenarios to investigate the long-term future of copper mining and guide exploration targeting strategies, in Proceedings International Mine Management Conference, pp 265-290 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 22, 2016

By E. R. Spencer, E. Reeves

National Institute for Occupational Safety and Health (NIOSH) researchers conducted an investigation to quantify sound levels and to determine the amount of sound reduction provided by engineering noise controls installed in a talc processing plant. Baseline sound level and sound intensity measurements were performed at the plant and the measurement locations were recorded for comparison to post-control measurements. Follow-up measurements were then made at the same locations after the initial noise controls were installed. The plant subsequently decided to implement additional noise controls and the researchers returned to conduct measurements for a final analysis of all noise controls. The most significant results showed a sound level reduction in the main mill area from a range of 93-104 dB(A) down to 90-94 dB(A), and a total sound power level reduction of 21 dB(A) for air classifying mill 3.

By A T. Job, M L. Edgar, P R. McAree

Characterising ores in-pit and in real-time presents a significant value opportunity for the mining industry. Hyperspectral imaging systems are proposed as an enabling technology to achieve this real-time characterisation. This paper considers the application of a hyperspectral imaging spectrometer mounted on a shovel. We define the performance requirements for such a spectrometer and associated subsystems during a typical dig-load cycle. The relatively high swing rotation speed of the shovel requires approximately video-rate exposure times to achieve good spatial resolution. We analyse a selection of components against these requirements and find that suitable commercial spectrometers, detectors and optics appear fit-for-purpose. Automated, real-time spectral classification systems are also available, with only relatively modest requirements for processing power. The paper argues that at near peak solar illumination, a system for field deployment at the required sensitivity is viable using only commercial off-the-shelf components.CITATION:Job, A T, Edgar, M L and McAree, P R, 2017. Real-time shovel-mounted coal or ore sensing, in Proceedings Iron Ore 2017, pp 397–406 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Axel Preusse

For the last 150 years, subsidence damage to the surface has been an unavoidable phenomenon associated with underground coal mining. In particular, the mechanization of mining methods in multiple seam mining and the concentration of mining activities in densely populated European metropolitan areas (e.g., Ruhr, Upper Silesian industrial region) have led to mining having a very strong influence on the earth?s surface. In both these regions, surface subsidence of more than 20m has been reported up to now in comparison to the original state. Underground coal mining in these regions strongly impairs all kinds of surface use, such as urban and industrial development, infrastructure (roads, waterways, and railways) and pipelines?without restricting the functionality of those objects to a greater extent. Demanding and, in some cases, globally unique engineering solutions have been developed and implemented for this purpose. The previously mentioned mining and industrial regions are still very strongly characterized by the (increasingly declining) coal industry and will remain dependent to a large extent and for an indefinite period on artificial drainage measures because subsidence that has already occurred is irreversible. This paper will primarily discuss the prediction of subsidence that is caused by intensive multiple seam mining and its influence on surface objects (e.g., underground pipelines). However, an approach for predicting ground uplifts due to rising mine water as a consequence of mine closures will also be described.

Jan 1, 2012

By W. J. Guay

Carbonaceous gold ores containing gold dispersed in sulfides are refractory to cyanidation because: (1 ) the carbonaceous materials adsorb gold during cyanidation; (2) a portion of the gold s so finely dispersed in the sulfide mineral lattice as to preclude contact with cyanide solution; and (3) a portion of the gold is chemically combined with carbonaceous material. Techniques which have been used to treat these ores are: (1) roasting or chemical oxidation to decompose sulfide and carbonaceous materials; (2) flotation to reject carbon; (3) the use of kerosene or other reagents to passivate the adsorptive carbon compounds; (4) carbon or resin in pulp; (5) flotation of a bulk concentrate which is treated by one of the above methods; and (6) the use of chelating agents which have a stronger affinity for gold than the activated carbon in the ore.

Jan 1, 1981

By C Adams

Reports of delays and cost blowouts in major study and construction projects are becoming increasingly prevalent in the resources industry. This is mainly being attributed to an escalating cost environment associated with the increased number of projects in the development to construction pipeline and a scarcity of competent skilled resources to deliver these projects. However, not all this effect can be directly attributed to the current environment. Historically the mining industry has not performed well in its ability to deliver projects according to the financial and physical parameters forecast in the feasibility study process. To manage the risks associated with delivery of major projects, resource companies need to ensure they use a standardised approach to management of their project development to satisfy project objectives and enable more efficient use of the increasingly limited available resources. Each discrete step in advancing the project from scoping study to operations needs to be integrated, reducing the amount of rework and duplication. This paper is primarily a consolidation of existing ideas on project management systems but also introduces new concepts to solve current issues. It describes the basic components of a typical mining project, the issues that commonly arise, the key attributes, and critical steps required for an effective integrated project management system covering projects from initial scoping studies through to project commissioning and operation. This paper focuses on technical study components of the mine development project with allowance for transitioning to design and construction and operation phases.

Jan 1, 2006

By K D. Wilkes

The WEMCO Heavy Media Drum Separator was first introduced by WEMCO in California in the 1940`s, initially from their base in San Francisco and later when the company moved to Sacramento. The WEMCO Company became a part of EIMCO Process Equipment in 1985, and in 2002 EIMCO became a part of the GL&V Group when Dorr-Oliver EIMCO was created. Throughout this period of time the WEMCO Drum has been installed on a variety of different applications and is now operating at the heart of many of the world?s largest Minerals and Coal Processing Plants, as well as being used by many smaller producers and metal re-cycling operations. This paper looks at the practical aspects of using WEMCO Drums in a representative range of processing applications.

Jan 1, 2006

By Dennis E. Jensen

Field studies were performed during blasting operations for strip coal mining above the room and pillar workings at Jenny mine in eastern Kentucky. The study is part of the Bureau of Mines program to develop criteria for the proximity of surface blasting to underground mines. Measurements and observations were made to identify physical changes in the mine. No change in the frequency of roof falls or any other indication of apparent damage was noted. Recordings of blast induced vibrations were made using sensors on the roof and floor of the underground mine and at the ground surface. A maximum particle velocity of 17.5 in/sec was recorded on the mine roof. The vibration data were analyzed and comparisons were made between roof vibration levels and those recorded on the mine floor and at the ground surface. Results are compared with previous blast vibration studies. Recommendations are made for further study toward developing criteria.

Jan 1, 1979

By E. C. Stephens

The eastern Washington— Idaho clay region stretches along the northeast margin of the Columbia basin for 150 mil es. The three better known and developed clay areas are Clayton, Wash., (2 miles north of Spokane); Mica, Wash., (10 miles southeast of Spokane); and Moscow-Deary-Bovill, Latah County, Idaho (about 80 to 90 miles southeast of Spokane) see Fig. 1. Clays from the eastern Washington— Idaho clay area have been mined for more than 50 years. At present Mica, Washington deposits are used by the Gladding—McBean & Co. to make a variety of bricks and ceramic products and Latah County, Idaho clays are used by the A. P. Green Fire Brick Co. to make refractories. The Anaconda Co. made an intensive investigation of the clay deposits in the northeastern Washington-!daho area in 1919 to determine the existence of a supply of raw materials from which alumina could be made. The greater part of the work, which included systematic drilling and shaft sinking, was concentrated at Mica, Wash. This was part of a research project carrted on by the Anaconda Metallurgical Research Dept. under the direction of Frederick Laist and F. Frick and it was terminated in 4920. V. D. Perry, Vice President and Chief Geologist for The Anaconda Co., in 1952 assigned the writer to make a preliminary study of clay and other potential sources of alumina ore in the Pacific Northwest with particular emphasis on those deposits which might be of future importance to The Anaconda Co9s. then new aluminurri plant at Columbia Falls, Mont.

Jan 1, 1961

By R. Tyreman, G. Ritson

"The Red Lake Mine is situated in Balmer Township, Red Lake area in northwestern Ontario. It is an underground mine that has been in production since 1948. The property was originally known as the Dickensen Mine and was shut down in 1996.A feasibility study was carried out in 1998 and it was determined that a new mill should be constructed with a throughput rate of 600 stpd. The life-of-mine average gold grade was projected to be 1.35 oz/t with gold predominantly associated with arsenopyrite and pyrite. Metallurgical testwork indicated that the optimal flowsheet for gold recovery would include an autoclave for oxidation with a carbon circuit for adsorption. To limit capital cost and establish cashflow, the mill was constructed without an autoclave. The recovery by gravity and cyanidation was projected to be 83%. A flotation plant was constructed at the tail end of the circuit to recover the additional gold associated with sulphides from the leach circuit tailings. This material is being stockpiled onsite for future oxidation treatment.Detailed engineering was started in early 1999 and the first gold was poured in August 2000. One feature of the project was the use of Contact Lake equipment from Cameco’s Contact Lake project. The entire mill was purchased and equipment re-used where possible. The capital cost for the process facilities was C$3 1.5 million."

Jan 1, 2001

By S G. Walters

The minerals industry is facing a productivity and investment crisis. The ‘Millennium Super Cycle’ from 2003–2011 was an unprecedented period of growth and investment resulting in increased throughput and development of lower grade resources to meet demand. During the boom quantity became more important than quality with throughput the key metric. This was accompanied by a general trend of decreasing feed grades across all commodities that was offset with higher production volumes.Current industry perception is that feed grade depletion is an unavoidable consequence of ore deposit geology and mass mining technologies for increasingly mature mining operations. In typical crush-grind-float operations value recovery only takes place at ~1–200 micron particle size during flotation, ie 3–4 orders of magnitude size reduction compared to primary feed. For increasingly low-grade deposits the cost of energy and capital intensity required to process and reject low value material at micron scale drives poor productivity. An alternative is to deploy a range of coarse (~10–100 mm) separation and rejection technologies. Grade Engineering® is an integrated approach to coarse rejection that matches a suite of separation technologies to ore specific characteristics and compares the net value of rejecting low value components in current feed streams to existing mine plans.Coarse rejection can be used on size distributions ranging from run-of-mine (ROM) to semi-autogenous grinding (SAG) discharge. Grade Engineering® is based on five rock based ‘levers’ linked to combinations of screening, sensor-based sorting and heavy media separation. These involve exploitation of preferential grade deportment to specific size fractions during breakage: differential blasting to condition grade by size at bench scale; sensor based sorting at truck and conveyor scale; and differential particle density.Grade Engineering® is being developed and implemented by a consortium of over 30 mining companies, equipment suppliers and research organisations. Emerging results from collaborative site activities demonstrate potential for generating significant value, which can reverse the trend of declining productivity due to feed grade depletion.CITATION:Walters, S G, 2017. Driving productivity by increasing feed quality through application of innovative Grade Engineering® technologies, in Proceedings Tenth International Mining Geology Conference 2017, pp 263–274 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Braden Lusk, Tristan Worsey, Nathan Rouse, Kyle Hall

Loading explosives up hole has challenges that are typically not seen in down hole explosive loading. Most explosives applications are not up hole. Lack of experience and technology can cause significant problems when loading explosives up hole. When results aren’t achieved, the blame is commonly put on the design when the true problems are unknown. Not knowing the cause of the problem causes drill and blast designs to be over engineered and very costly with little success. Being able to know and record key data is crucial to actually solving the problem. This paper goes over blast instrumentation that can be used to trouble shoot drill and blast problems in up hole explosives loading in underground mines. The tools and procedures used to trouble shoot include velocity of detonation recorder, borehole tracking, seismographs, and borehole camera. Each item will be discussed in detail with a case study to show the usefulness of the instrumentation. The operation discussed in the case study had issues pulling raises and had hang ups in the stope shots. These problems caused production slowdowns and costly remediation blasting that was not very successful. The case study is an underground gold mine that used modified sub-level caving with backfill as the mining method.

Jan 1, 2018