Search Documents

By F. J. Perzak

The Bureau of Mines conducted a flammability study of plastic ventilation ducts. Six rigid 16-in-diam fiberglass-reinforced plastic ducts from five manufacturers were examined using laboratory-scale, large-scale, and full-scale fire tests. The laboratory-scale tests included the American Society for Testing and Materials E162 radiant panel test, the E2863 oxygen index test, and the standardized small-scale flammability test (S3FT) developed by the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, and replicated by the Bureau of Mines. Ten-foot lengths of the same ducts were also subjected to a large-scale vertical fire test, and 20-to 30-ft lengths were tested in a full-scale in-mine fire test at the Bureau's Lake Lynn Laboratory mine. The data from the laboratory-scale radiant panel test and oxygen index test indicated that the ducts were fire-resistant, However, five of the six ducts failed the S3FT and vertical fire tests, and four of the ducts failed the full-scale in-mine tests with flame propagation rates that ranged from 3 to 10 ft/min. The results indicate the need for improved fire-resistant plastic ducts. The good agreement between the S3FT re-sults and the vertical and full-scale tests show that the S3FT provides a good indication of the flammability of fiberglass-reinforced plastic ducting under realistic fire conditions.

Jan 1, 1987

By John A. Breslin

The Bureau of Mines measured respirable dust in coal mines by means of multiple dust samplers worn by persons moving about the mines. The measurements were made primarily to evaluate the effectiveness of certain dust-control techniques; however, for this report, the data have been analyzed to determine the precision of the personal dust-sampling measurements. A total of 68 sets of measurements were available from multiple personal samplers. The measured dust masses were less than 1.0 mg because the sampling times were short. The coefficient of variation calculated from these data was 18.5 pct, compared with coefficients of variation ranging from about 10 to 30 pct, which were calculated from the most precise and extensive data available for fixed-point dust measurements made in coal mines. From this comparison, it is concluded that dust samplers worn by personnel are as precise as fixed-point samplers in measuring respirabe coal dust; the wearing of the samplers by someone moving about a mine does not contribute significantly to the variation in measurements made with these instruments.

Jan 1, 1983

By J. F. Shea, O. F. Tangel

Battelle Memorial Institute participated in a program for the General Services Administration aimed at developing a nickel-cobalt separation process that could be integrated in the Nicaro nickel plant. At the time the programwas being carried out, the Nicaro process was a straight-through operation, in which the ore was reduced and leached, after which the pregnant solution was boiled to produce a so-called "bulk precipitate" which contained virtually all of the nickel and cobalt which had been dissolved in the leaching step. The weight ratio of nickel to cobalt in Nicaro ore is approximately 15 to 20:l. The weight ratio of nickel to cobalt in the finished product had to be 100:l or higher to meet specifications. Because the Nicaro process embodied no nickel-cobalt separation step, the only way that a bulk precipitate of the specified nicke1:cobalt ratio could be produced was to so adjust roasting and leaching conditions that nickel would be selectively leached and most of the cobalt would be rejected with the tailings. The required selectivity, however, was achieved at the expense of nickel recovery, which was 5 or more per cent less than might have been obtained with the existing equipment, utilities, man power, etc., had selectivity been no object. The over-all purpose of the program was to develop a separation step that could be fitted into or onto the Nicaro facilities and which would permit the manufacture of a product that would meet the desired specifications and still permit the recovery of a maximum amount of nickel. Battelle suggested that this might be accomplished by reprocessing off-specification bulk precipitate and specifically suggested the process based on ammonium sulphate leaching followed by hydrogen reduction of the leach solution according to techniques developed commercially by Sherritt Gordon Mines Limited. Such a process would not only satisfy the objectives of the research but would present two additional advantages. (1) It would produce a separate cobalt product which could be further processed into metal, alloys, oxides, or salts. (2) It would yield nickel in metallic form which might be more generally marketable and command a slightly higher price per unit of nickel than the Nicaro oxide product. DESCRIPTION OF THE PROCESS Figure 1 is a flowsheet of the process. The essential features are: (1) Extraction of about 97 per cent of the nickel and about 85 per cent of the cobalt from bulk precipitate by a principal leach with ainmonium sulphate solution (Step A). Extraction of virtually all of

Jan 1, 1961

By H Thanasekaran, J Kohmuench, B Seaman

To achieve an efficient separation in the flotation process, valuable particles need to be selectively segregated from the gangue while utilising a minimum number of flotation stages. TodayÆs existing flotation technologies are effective for fine particle size classes; however, limitations due to particle buoyancy and bubble-particle detachment restrict the effectiveness of traditional flotation approaches on coarser particles. As a result, flotation circuits are generally configured to process only fine particle size classes in order to maximise recovery in the primary stages. Eriez has invented a novel flotation technology, the HydroFloat, which overcomes these limitations by carrying-out flotation in a dense, fluidised-bed medium allowing for the recovery of coarse particles (>0.250 mm). Over the last 15 years, this technology has been successfully applied to industrial minerals with several full-scale units installed to recover particles up to and exceeding 3 mm diameter in primary flotation circuits. This paper includes discussions on the history of this technology, process theory, existing applications, and a review of recent sulphide-based laboratory test work conducted for Newcrest mining and others. Benefits of this approach, such as improved recovery, low energy consumption and reduced reagent addition will also be reviewed.CITATION:Kohmuench, J, Thanasekaran, H and Seaman, B, 2013. Advances in coarse particle flotation - Copper and gold, in Proceedings MetPlant 2013 , pp 378-386 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Graham Davey

"Low speed stirred milling has been employed for many years in the metalliferous and industrial minerals industries. High speed stirred milling is a relatively new method of grinding in the metalliferous process industries. However it has been it has been in wide spread use in the industrial mineral field for over 30 years for various minerals. Many existing metallurgical operations are looking to maximize economic return from existing deposits, requiring new thinking and technologies. By combining low speed and high-speed milling fine and ultrafine grinding efficiency and operating costs can be improved.The correct selection of different fine grinding technologies is covered, when each mill is applicable and when a combination of the VERTIMILL® Grinding Mill and SMD provides the best economic solution.INTRODUCTIONUltra-fine grinding of minerals has been in wide spread use in the industrial mineral field for over 30 years. Within the last 10 years the metalliferous industry has shown interest in the ability to produce ultrafine particles, as chemical, physio-chemical and physical separation processes have advanced to be able to treat ultrafine metalliferous particles. Also as the primary mineral deposits, around the world are depleted, new more difficult deposits must be mined. Existing operations are also looking to maximize economic return from existing deposits, requiring new thinking and technologies.The traditional approach for gold containing refractory material has been to liberate the locked gold by chemically destroying the pyrite through oxidation. Roasting, pressure oxidation, and bacterial oxidation all employ various degrees of temperature, pressure and catalysis to react the pyrite with oxygen to produce iron oxide and sulfur by-products. However all of these methods are economically impacted due to specific operational added requirements and emissions controls. Pressure and bacterial oxidation have very high capital and operating costs."

Jan 1, 2006

By Wallace W. Roepke

The Bureau of Mines conducted a series of experiments using Illinois No. 6 coal to determine the effect of asymmetric wear on airborne respirable dust (ARD), specific energy, cutting force, and normal force. Plumb-bob-type bits--one new bit and four ground with different sized flats--were used. Constant-depth linear cuts at 0.32, 0.64, 1.27, and 2.54-cm cut depths were made. Both cutting force and normal force increased as the flat area increased. Specific energy demonstrated a statistically significant increase with flat area at the 0.32-and 1.27-cm cut depth only. Specific ARD showed a statistically significant decrease with increasing flat area only at the 0.64-cm cut depth. Increasing cut depth increased cutting force but decreased specific energy and specific ARD. Normal force increased with increasing cut depth for the new bit but exhibited a maximum at 0.64 cm for the bits with flats.

Jan 1, 1983

By Larman J. Heath

Wellbore enlargement was tested using hydrazine hydrate in a gas-storage well in Ohio to increase the well productivity. The wellbore was to be enlarged by chemical disaggregation of the sandstone adjacent to the wellbore. Productivity immediately declined 49.1 percent and gradually declined to zero in 7 months. A down-hole camera survey showed a white-to-gray precipitate covering the entire wellbore surface. The precipitate was chemically analyzed and identified as mostly carbazic acid, a hydrazine derivative of carbonic acid. Formation of this precipitate was not anticipated; this viscous sub-stance caused the gradual loss in productivity of the well. The wellbore was not enlarged. Laboratory tests were run to determine what clay stabilization measures could be taken in sandstone cores to prevent clay swelling and particle migration caused by hydrazine hydrate. Normal clay stabilization methods did not prevent the virtually complete loss in permeability to hydrazine hydrate. Other laboratory tests using natural gas diluted with small amounts of carbon dioxide confirmed the ease with which carbazic acid could be formed in a hydrazine hydrate-saturated environment within and adjacent to the wellbore.

Jan 1, 1970

By Joseph Grumer

Theory pertaining to the exchangeability of fuel gases on appliances has been extended to exchanges of propane or butane with mixtures of these. In particular, new considerations were developed bearing on the hazard of an occasional emission of carbon monoxide and flashback and blowoff possibilities. The new considerations involve using current requirements for approval of liquefied petroleum gas appliances. These requirements were used to predict allowable tolerances in chemical composition of liquefied petroleum gases for existing appliances. In addition, changes in gasline pressure were computed which may be substituted in place of fuel exchanges during testing of appliances,

Jan 1, 1962

By M. Kumral

Raw material fed into a processing or refining plant is required to be uniform in composition for several reasons. When the mined ore is highly variable in quality the only way to ensure consistency is to homogenize the ore prior to the process. The problem is more complicated in the case of multiple ore sources. The idea behind the research is that theoretical blending ratios can serve not only to meet predefined specific criteria but also to reduce grade fluctuations of variables under consideration. In this paper, the problem is formulated as a quadratic programming problem, whose objective function is in quadratic form and constraints are linear. A case study was conducted on a data set from an iron orebody to demonstrate the technique. The objective was to minimize the blend variability in terms of each variable (in this study, iron, silica, alumina and lime) grade of ores extracted in three different production faces. The stockpile capacity, lower and upper limits of each variable satisfying operational requirements and non-negativity were constrained to the model. A modified simplex method developed by Wolfe was used for solving the blending and homogenization problem. The promising results can be used as apart of the stacking and reclaiming design. Keywords: blending and homogenization problem, quadratic programming, Wolfe method.

Jan 1, 2005

By K-H. Frohne

This report presents a study of the Cooper sand of the Fork Run pool of Warren and McKean Counties, Pa., and a prediction of the secondary oil recovery by gasflooding the reservoir. A computer program employing a modification of the Craig, Geffen, and Morse secondary recovery calculation was used to make the gas flood performance forecast and is presented in the appendix. The Cooper sand reservoir in the Fork Run pool lies at a depth of about 1,900 feet and covers an area 1/2 mile wide by 2-1/4 miles long. Original oil in place is estimated to have been 8,266,000 STB. The primary recovery mechanism is solution gas drive, and ultimate primary recovery may reach 20 percent over a well life of 90 years. Two computer predictions were made for gas flooding the Cooper reservoir. The first was for a 25-acre pilot five-spot utilizing existing wells, but project economics were poor since only 25 percent of injection gas is utilized for pilot oil recovery. Recovery was 71,000 STB, or 22 percent of oil in place at flood initiation, but required 25,700 scf gas injected per STB of oil recovered. In the second prediction, pilot area performance was projected for the entire Fork Run pool, and economics became good. Recovery was 1,753,000 STB from 25 five-spots after the injection of only 6,400 scf per STB of oil recovered.

Jan 1, 1969

By Willie M. NeSmith

Conventional augered, cast-in-place (ACIP) piles were introduced into the New York City area as a result of the damage to existing structures caused by pile driving operations. ACIP piles are often specified where deep foundations are to be installed adjacent to transit facilities, sensitive underground utilities or in close proximity to existing structures. However, loss-of-ground issues associated with the installation of ACIP piles have prevented the wide-scale use of these systems. Beginning in 2002, Berkel & Company Contractors, Inc. began using its augered, cast-in-place displacement (ACIPD) system in the New York City area. Like conventional ACIP piles, this system produces almost no vibration. Also, as almost no material is brought to the surface, there is no opportunity for loss of ground. This paper presents a description of Berkel's displacement pile system and a brief discussion of six projects in the New York City area that have been executed with this system over the past two years.

Jan 1, 2004

By E. Sun

Tailings disposal is a significant consideration for the mining industry, with the majority of the ore processed in most mining operations ending up as tailings. Several tailings dam failure accidents have occurred during the past few years and mine tailings dam failures are occurring at relatively high rates. Tailings dam failure is disastrous with the serious damage and the loss of lives. To increase the tailings dam safety, a tailings dam monitoring and pre-alarm system (TDMPAS) based on the internet of things and cloud computing platform has been accomplished with the abilities of real-time monitoring of the saturated line, impounded water level, rain fall and the dam deformations etc. The TDMPAS has been applied in several mines in China and helped the mine engineers monitor the tailings dam safety and get warning information automatically and remotely in any kind of weather conditions. This work has been demonstrated the tailings dam monitoring and pre-alarm system (TDMPAS) is meaningful to monitor the tailings dam physical safety condition. The TDMPAS could be applied to monitor all the national tailings dams online in the future.

Jan 1, 2012

By Fawad S. Niazi

Ever since the use of the cone penetration test (CPT) in geotechnical practice, attempts have been made to correlate CPT parameters with pile capacity components of unit end bearing (qb) and unit shaft resistance (fp), thus deriving multiple CPT-based pile design methods. These methods focus on "capacity" only without consideration to complete axial pile load-displacement (Q-w) response. Estimated capacities from these methods also exhibit considerable scatter without any consensus on their consistency. In addition, load-displacement curves obtained from axial load tests on highly expensive and extensively instrumented piles can exhibit different shapes. Nevertheless, a single value from the curve so obtained dictates the design capacity. Currently, there are at least 42 different criteria defining capacity with considerable variation in the values obtained thereof. The Randolph elastic solution, which provides a framework for analytical evaluation of pile load-displacement response, requires the profiles of soil stiffness. The fundamental soil stiffness defined by the small-strain shear modulus (Gmax) can be obtained from shear wave velocity (Vs) readings via seismic piezocone tests (SCPTu). The secant stiffness (G), which softens from Gmax corresponding to operational load levels, can be obtained by generating stiffness reduction curves from back analysis of load tests. Then, using appropriate G values, the Q-w curve can be defined for conditions similar to the database from the pseudo strain (w/d). Thus, a complete framework for optimal integration of SCPTu data, Randolph elastic solution and back-analysis of field operational stiffness can be established for complete axial pile foundation analysis.

Jan 1, 2011

By J. J. Taber

Gas and water permeabilities of a large number of samples from the Pittsburgh and Pocahontas coals were measured at various overburden and mean flow pressures. A wide variation in the air and water permeabilities was obtained for each type of coal. Overburden pressure has the most significant effect on the single-phase permeability. Considerable hysteretic effect was observed for both air and water permeabilities. Gas permeabilities are affected to a lesser degree by mean flow pressures above atmospheric. However, at subatmospheric mean pressures, appreciable increase in permeability occurs for low permeability samples. Air and water relative permeabilities were also measured for numerous samples of Pittsburgh and Pocahontas coals. Tests were performed under steady-state conditions for both drainage and imbibition cycles. Results indicate that the flow of gas is greatly reduced during the latter process, whereas it is largely undiminished over a wide water-saturation range during drainage. It is also shown that imbibition saturation distributions obtained from liquid-water imbibition as opposed to water-vapor adsorption produce gas permeability curves of radically different character. The effective permeabilities to both gas and water were significantly reduced with the application of overburden pressures in the range of 0 to 1,000 psig, but the general shapes of the relative permeability curves remained the same.

Jan 1, 1974

By Richard Hanke

Tunnel construction on the Brightwater Conveyance System?s East and Central contracts required ground modifications of the existing site soils, comprised of sandy alluvium to very dense glacial till, to assist with both hand-mined and TBM tunneling operations at vertical access shafts. The ground modification program was completed with a modified double fluid jet grouting system to construct continuous overlapping soilcrete columns to depths up to 94-ft below existing grade. This paper presents the sequence and methodology for the ground modification work and capabilities of jet grouting for structural support and groundwater control in the challenging soil profile present at the Brightwater Conveyance System Project.

Jan 1, 2008

By Tom C. Palangio

The mining industry has come to rely on imaging devices to monitor and record all kinds of activities. We use them to measure, improve the process, ensure security, increase production and automate machinery. Cameras can be installed in locations most people wouldn?t want to live and be our ?eyes? to record the events at that location. This paper discusses digital imaging, the equipment, methods, techniques and information that can be learned from digital devices used in mining operations. The guy who said ?a picture is worth a thousand words? probably understated it. Images are the perfect way to document conditions before, after and even during mining activities. Today?s wide choice of cameras, camcorders and other digital devices allow us to record most activities and events. The technology is advancing at a high rate. Digital cameras and camcorders are marvels of technology with high resolution optics, compact size, automatic time and date stamp, great battery life, shutters to freeze motion and computers to auto focus and eliminate jitter (image stabilization). Add to this the economical price and ease of use and everyone in this industry should be aware of the possibilities.

Oct 1, 2010

By Philip J. H. Ball

The new application and development of grout jacking processes has combined, over the last decade in particular, to provide a method by which the effects of new underground construction on superficial structures can be controlled to acceptable levels. This paper sets out the basic principles, processes and limitations of compensation grouting. It describes key elements of the philosophy and design and details the control systems required to perform satisfactorily. To illustrate the application, a case history is described for the construction of a shaft and tunnel within and beneath the prestigious structure of Harrods in London.

Jan 1, 2000

The usefulness of laboratory studies - petrology and mineragraphy in the search for, and investigation of, mineral deposits should not be exaggerated, but it should not be overlooked, because such studies will always contribute to an understanding of the geology of the deposits, and can on occasions provide invaluable information not otherwise available. A few examples furnished by the investigations of the Mineragraphic Section of the Commonwealth Scientific and Industrial Research Organisation will show this.Petrology.In the early stages of the investigation of the King Island scheelite deposit, during the war, when the nature of, the deposit was not understood, a series of samples embodying the exposed rock types was submitted to the Mineragrap;hic Section for petrologicalexamination by the Mineral Resources Survey. It was at once apparent to the petrologist that the King Island scheelite ore was a contact metamorphic deposit, in which a series of argillaceous shales, calcareous shales, impure limestones and limestones had beenintensely metamorphosed. The shales had been converted to finegrained biotite and actinolite hornfels, according to their lime content, and the impure limestones to fine-grained diopside hornfels, garnetdiopside hornfels and garnet hornfels (calc-flint), the garnet being the lime variety grossularite. The limestones, however, after being first converted to marbles, had suffered intense pyrometasomatism, involving substitution of immense quantities ,of silica and' iron for lime and carbonate, and had been converted largely to a coarsegrained garnet rock, in which the garnet was the lime-iron variety, andradite. The silica and iron were derived from the mineralising solutions of the adja,cent ,granite. intrusion, responsible for the contact metamorphism, and were accompanied by tungsten and some molybdenum. The tungsten in the presence of so much mobile lime, was precipitated as schecelite, much of it finegrained and enclosed in or intergrown, with the andradite garnet or the quartz interstitial to the garnet.It was apparent that the King Island scheelite deposit, was a perfect example of selective pyrometallomatic replacement in a bedded contact metamorphic deposit. The bedded nature of the original rocks was preserved, and the scheelite was practically limited to the original limestone beds, 'Which had been so much more susceptible to replacement after recrystallization, than the other sediments. The further geological study of the deposit then resolved itself into the task of mapping the folding and faulting of the deposit, with bore cores to provide the stratigraphic sequence, and establish the number of scheelite-bearing beds.A second example is provided by a petrological investigation of the mineral composition and genesis of the talc deposits of the Gumeracha district of South Austral.ia, which was undertaken at the request of the South Australian ,Mines Department, in conjunctionwith mapping of these deposits. The field geologist mapping the deposits was experiencing some difficulty in interpreting the structure...

Jan 1, 1950

By Ali Porbaha

Rapid growth in the urban development requires continuous search for innovative technologies to construct complex infrastructure systems. Deep mixing is one promising construction technology that has a wide spectrum of applications for development and expansion of complex urban facilities. Large number of reported case history of the projects in Europe, Japan, and the US demonstrate the versatility of the technology compared to conventional methods of ground modification. A large number of factors influence the quality of the soil cement columns; some of these are rooted in the installation process and the effective use of machinery during construction. This paper attempts to present some issues related to installation of deep mixing that affect quality of the treated columns. Presented here are various installation patterns, installation machinery, installation sequence, effect of penetration/withdrawal injection methods, penetration/withdrawal speed, effect of number of shafts, rotation of the blade, shape and orientation of mixing tools, and rotational speed of the shaft on quality of the treated ground.

Jan 1, 2001

The re-use of waste water from coal preparation plant tailings is always desirable, but is generally problematic in terms of solid-liquid separation. Dewatering and disposal of coal slurry at a high percentage of moisture poses a major technological and environmental challenge to mining and mineral processing industries world-wide. Characterization and flocculation of these coal tailings reveals that the separation of fine coal tailings depends on factors such as size distribution, slurry viscosity, zeta potential, pulp density, circuit design, plant operating parameters, and the behaviour of solid particles in an aqueous medium. The present study was carried out on -600 mm coal tailings collected from a coking coal preparation plant of Jharia Coalfield, India, using anionic flocculent. Characterization studies revealed that the zeta potential was highest (-44 mV) at a pH of 9.0, the size range of the particles was 1.1?700 m, and the average ash content was 62.57%. Flocculation studies were performed at different solid concentrations, pH values, and polymer dosages. The results indicated an efficient settling rate of 178.15 mm/min at 8% solid (w/w) at a flocculent dosage of 32.50 g/t solid. The turbidity of the clear liquid obtained was 7.42 NTU.

Jan 1, 2014