Search Documents

By Tracy Brettmann, Will Bohlen

An innovative retaining wall design consisting of tangent drilled shafts with supplementary seal piles was used to limit continuing bank erosion along the Brazos River in Southeast Texas. The riverbank erosion had progressed to where it was threatening the stability of both the bridge abutment and corresponding approach embankment of the heavily travelled Highway 99 bridge at this location. A tangent pile design was selected because it was both much faster to install and more cost effective than a secant pile system. The design included both 5.5-ft and 10-ft diameter shafts with depths up to 130-ft and comprised both anchored and cantilevered sections. Supplementary seal shafts were also installed between the structural tangent drilled shafts to help plug any gaps between the tangent shafts. The plumbness and diameter of the shafts were tested using a sonic caliper to make sure the shafts were installed within the specified tolerance. The initial design had to be revised when a record flood from Hurricane Harvey impacted the site during construction. Introduction The Fort Bend Grand Parkway Toll Road Authority (Owner) needed to protect the north bridge abutment with a retaining wall system due to rapidly eroding conditions of the Brazos River banks within the 300- feet-right-of-way of the State Highway 99 Jodie Stavinoha Bridge. The extent of the local scour and erosion along the north bank of the Brazos River has caused concern for the structural integrity of the bridge. The magnitude of the erosion along the north bank at the location of the bridge has been measured at about 120 feet over three recent hydrologic flood events locally referred to as Memorial Day 2015, Memorial Day 2016, and Tax Day 2016. During construction, a new record flood level occurred due to Hurricane Harvey in August of 2017 that resulted in a portion of the retaining wall needing to be redesigned due to even more erosion occurring. The Brazos River is an actively eroding and meandering alluvial river plain that naturally meanders and migrates over time. The processes of bank erosion and meander migration were ongoing before the bridge was constructed and will continue in the future. These recurring major flood events, however, rapidly increased the rate of erosion in just a few years. Background. Due to the need to protect the bridge as soon as possible, the Owner selected a project team consisting of the designer, general contractor and specialty deep foundation contractor prior to final design to work together in developing a cost-effective design that could be implemented rapidly. The project team initially considered both a secant pile and tangent pile retaining wall system using drilled shafts. After reviewing various alternative designs, a tangent pile wall with seal piles was selected based on both cost effectiveness and speed of installation. The tangent pile with seal pile option was approximately 20 percent lower in cost and 50 percent faster to install.

Jan 1, 2018

By M. Clair Smith

This report is one of a series being prepared by the Bureau of Mines on exploration, development, mining methods, and costs at various open-pit mines in the United States. These reports have been prepared in cooperation with various mining companies. A similar program, conducted from 1928 to 1939, was generally conceded to have contributed to improving the efficiency of mining operations. The purpose of these reports is to promote development and conservation of our mineral resources by disseminating technological information on mining methods and practices. This report describes exploration, development, equipment, and mining by open-pit methods of the remainder of an ore body that had been previously worked by underground methods. The Tripp pit of the Consolidated Coppermines Corp. is located at Kimberly, Nev., a small mining company town having an elevation of 7,250 feet, 9 miles by road west of Ely, Nev. (fig. 1). The pit extends over the area formerly mined by underground methods from the Morris and Brooks shafts.

Jan 1, 1962

By R. Stefanko

This Final Report covers the work performed for Contract No. H0377043, "Cables for Face Equipment" from August 1, 1977 to April 1, 1981. It reports the findings in three areas of research: cable protection, circuit-breakers, and high-voltage cable couplers. Laboratory and analytical studies have been conducted in the three areas to determine proper circuit-breaker settings, cable sizes, and coupler performance. Also, an extensive field-monitoring program was established to relate in-mine epxerience to laboratory findings. Further, various pieces of equipment was designed for laboratory testing, particularly in the area of cable reeling and unreeling.

Jan 1, 1981

By K. J. Liles

The Bureau of Mines conducted laboratory semicontinuous and continuous heavy liquid tests to determine the feasibility of producing commercial-grade products from the high-clay sylvinite ores of the Permian Basin in New Mexico. Continuous test operations demonstrated that concentrates containing 59.9 percent K2O and recoveries of over 75 percent of the contained potash can be obtained. The organic heavy liquid was effectively recovered by vaporization, condensation, and absorption methods. Less than 5 parts per million of heavy liquid vapors were released to the atmosphere. This loss represents only 0.02 pound of heavy liquid per ton of ore treated.

Jan 1, 1973

By John E. Kelley

A method for measuring the spark-shower radiance of metals when abraded on a grinding wheel was developed by the Bureau of Mines for evaluating the sparking tendency of metals. The radiance was measured in units of emissive power per solid angle per area of the detector. Over 100 metals were tested and rated relative to commercially pure iron. The metals tested included elemental metals, iron binary and ternary alloys, iron-carbon ternary alloys, commercial steels, nonferrous alloys, and a few hard-metal compounds. Some alloys were synthesized; others were obtained commercially. Alloys that possessed good strength properties were emphasized for selection. The results indicate that the spark-shower radiance of plain carbon steels and carbon alloy steels was greater than that of pure iron. Certain elements, particularly vanadium and chromium, reduced the sparking tendency of iron. Stainless steels and particularly nickel alloys displayed low spark-shower radiance. Some metallic elements had much lower radiance than iron; others, much greater. Plain carbon steels, heat treated to a variety of hardnesses, gave radiance values that generally increased with increasing hardness. The effect on sparking tendency of an increase in hardness of an alloy steel was studied. The sparking tendency increased with an increase in hardness to a maximum, then decreased with a further increase in hardness.

Jan 1, 1974

By Lijuan Chen

During the detoxification of chromium-containing slag by Achromobacter sp. CH-1, anionic surfactant Sodium Dodecyl Sulphate(SDS) and its mixed systems with different Tween surfactants(Tween 20, Tween 60 and Tween 80) were used to promote the interaction between the bacteria and the chromiumcontaining slag and the rate of acid-soluble Cr( ? ) leached from the slag. The effects were evaluated by the surface tension, the pH of the leaching solution and the leaching rate of total Cr( ? ) from the slag. The results showed that the surfactants systems improved Cr(VI) leaching and its detoxification of chromium-containing slag. The mixed surfactants of SDS combined with Tween surfactant revealed better effectiveness of detoxification than SDS only. When the mass ratio of SDS to Tween 80 was 1:1, the rate of Cr( ? ) leached from the slag increased by 12%.

Jan 1, 2009

By Paul G. Swanson

This investigation was conducted to identify the principle causes of spoil instability problems in the Eastern Coal Province. The study was also conducted to develop a matrix to predict the strength and groundwater parameters necessary to conduct stability analyses on a proposed reclamation scheme. Suggestive methods to reduce spoil instability potential are also included. Numerous physical property, strength, compressibility, chemical and mineralogical tests were conducted on mine spoil samples obtained from 11 different surface mine sites. Site characteristics that influence the position of the post reclamation groundwater table were identified. Distinct regions within the Eastern Coal Province with high incidences of surface mine slides or high landslide susceptibility were identified. The application of the predictive matrices developed in this study is for surface mine sites mined and reclaimed in general accordance with the Surface Mine Reclamation Control Act of 1977. A review of current mining practices and the relative effect on spoil stability is included.

Jan 1, 1983

A review is presented of developments in mill liners to improve performance in terms of wear, impact, as well as mill grind and throughput. These developments are in response to the growth in size of SAG mills and the use of larger ball loadings and ball sizes in modern SAG milling practice. Shell liner developments include specific mechanical design features such as special bolting, directed metal flow to prolong liner life and a focus on the process aspects of the mills to provide more effective grinding motion with reduced wasteful ball-on-liner impacts. Grate design developments aim to provide high throughput of material, especially in the larger size fractions, while providing good impact and wear life. Curved pulp lifters are designed to ensure, at high mill speeds, complete discharge of coarse solids from the mill.

Jan 1, 1999

By Oliver C. Fursman

These investigations were conducted to determine conditions for recovery of nickel and copper from Funter Bay, Alaska, sulfide ore and recovery of nickel from nickel-silicate ore, Nickel Mountain, Riddle, Oreg. Samples of Funter Bay cupriferous and nickeliferous pyrrhotite ore, were treated by beneficiation, roasting, electric smelting of roasted are for matte production, chlorination, leaching, and sulfatizing roasting with subsequent leaching. Funter Bay and Nickel Mountain ores were smelted together to produce matte. Total sulfide flotation, followed by magnetic separation of the tailings to recover entrained nickel-bearing pyrrhotite, resulted in the highest nickel recovery in beneficiation tests on Funter Bay are. Overall beneficiation resulted in recovery of 98.5 percent of the copper and 95.4 percent of the nickel in the concentrate that contained 3.5 percent copper and 1.7 percent nickel.

Jan 1, 1962

By Gerard de Vries

pipeline industry and are still growing in size. Liquid epoxy and polyurethanes are an excellent choice for whatever the aggressiveness of the substance transported and whatever the harmful outside influences, maximum protection is required. They can be used as coatings on all kind of pipelines varying from the mainline coating to the field joint coating. Compared with traditional systems like dual layer FBE and 3-layer polyolefin there are some benefits to be considered like easiness of repairs, amount of coats, application temperature and film thickness. The interior coating renders the pipe surface so much smoother that considerable savings can be realized in pump stations. Apart from the interior of the pipeline, the industry is faced with new challenges like higher operating temperatures of lines and an emphasis on product benefits in order to save money. Key words: liquid epoxy, liquid polyurethane, phenolic epoxy, pipeline, field joint coating, internal coating, corrosion control

Jan 1, 2006

By K. P. V. Lei

The Bureau of Mines investigated molten-salt electrorefining as a practical method for reclaiming vanadium from vanadium scrap. An electrolytic process utilizing a KC1-LiC1-VC12 electrolyte at 615° C was developed for producing ductile vanadium with a purity over 99.9 percent. The recovery of the vanadium in the cell feed ranged from 88 to 93 percent with a current efficiency from 83 to 95 percent.

Jan 1, 1967

By E. E. Buban

A self-contained breathing apparatus has been developed to provide complete respiratory protection for a miner in an irrespirable atmosphere. The apparatus has the desired features of comfort, reliability, maintainability, and quick-donning capability. The apparatus is packaged in a moistureproof envelope and is protected in a shock absorbing, fiberglass resin carrying case. The apparatus is a small, lightweight, one-time-use device that can be readily worn on a miner's belt, requires no maintenance and is designed to have a shelf life of five years and a carrying life of three years. It is deployed to the use position in a period of 15 to 30 seconds. Man tests conducted in-house and at the National Institute of Occupational Safety and Health (NIOSH) testing laboratories established that this unit meets all performance requirements listed in the Code of Federal Regulations, Title 30, Part 11, Subchapter B, Subpart H (CFR 30, Part 11) for respiratory protective devices. The unit, which has received joint approval (TC-13F-37) on a prototype basis from the Mining Enforcement and Safety Administration (MESA) and NIOSH has: (1) Ten-minute service life under escape conditions. (2) Thirty-minute service life when the wearer is at rest. (3) Peak-to-peak breathing resistance of less than our inches water column height. (4) Inspired gas temperature of less than 135°F. (5) Breathing gas contents greater than 19.5 volume per cent of oxygen and less than 2.5 per cent carbon dioxin. (6) A weight (complete in carrying case) of 2.75 lbs. (7) A carrying case size of 6-1/2"x 5-1/8"x 3-1/8".

Jan 1, 1974

By E. R. Bauer

Previous studies and research efforts have shown that noise-induced hearing loss (NIHL) is a problem in the U.S. mining industry. This is especially true in surface and underground coal and stone mining where large, noisy equipment predominate. Workers in coal preparation and stone processing plants have also been found to be subject to high sound levels that could potentially cause NIHL over prolonged periods of exposure. National Institute for Occupational Safety and Health (NIOSH) researchers have been conducting a cross-sectional survey of equipment noise and worker noise exposures in the mining industry to estimate the potential for NIHL within the mining community. One commodity recently surveyed was the extraction of sand and gravel from surface pits and by river dredging. Little is known about the noise environment and worker exposures in these environments, where processing and mining equipment similar to coal and stone are employed. To address the potential for NIHL in the sand and gravel industry, sound levels on and around the dredges and processing equipment were recorded to identify areas of high noise levels. Full-shift worker dosimetry, in conjunction with task observations, was documented to determine the relationship between exposure and source. This paper presents research examining noise on dredges, in several surface mine sand and gravel operations and in the processing facilities. The locations where workers are likely to be overexposed and were found to be most susceptible to noise overexposures are reported. Results indicate that there are areas on the dredges (crane, suction pumps, and diesel engines) where sound levels greater than 90 dB(A) are present. In addition, crushers and screens used in the processing of the sand and gravel also generate sound levels greater than 90 dB(A). Although no surveyed worker exceeded the Mine Safety and Health Administration (MSHA) Permissible Exposure Level (PEL) of 90 dB(A) TWA8, laborers, mechanics, oilers, helpers, pickers, and greasers are the workers likely to be exposed to hazardous sound levels and thus develop NIHL over time. Knowledge of the equipment noise, area sound levels, and worker dose levels is information that management and employees can use to reduce exposures. Exposures can be reduced in certain areas through administrative controls and through engineering controls applied to the noisiest equipment.

Jan 1, 2008

By Oliver Bowles

Marble is one of tile most beautiful and enduring materials employed in the construction industries. Because of its diverse colors, decorative patterns, and varying textures, it has furnished material for artistic architectural design for many centuries. The marble industry is described in some detail in Bureau of Mines Bulletin 106, The Technology of Marble Quarrying, which, unfortunately, is now out of print but may be consul ted at most large libraries. Onyx marble and travertine are discussed in Bureau of Mines Information Circular 6751. The purpose of this paper is to describe the main features of a distinctive group of ornamental marbles known as the serpentine marbles or verde antiques.

Jan 1, 1938

Sandsloot open pit is situated on the northern limb of the Bushveld Complex, 250 km north east of Johannesburg, South Africa. Sandsloot is currently the largest open pit platinum mine in the world and is one of six potential open pits in the area. The geotechnical strength properties of the Platreef have posed significant mining and processing challenges to the PPRust operation since inception in 1992. In order to optimize the whole business as opposed to isolated cost centres a mine to mill initiative was embarked upon in 1997. Initial work focused on ore characterization and an entire suite of data was collected for each rock type. This included mineralogy, geochemistry, geotechnical, blast ability indices, as well as metallurgical strength data. The second phase involved the clear definition of customer requirements, namely the optimum performance criteria for the plant and mining departments. This involved extensive field trials and data capture to measure the interaction and influence of the mine to mill value chain. Once the design targets were defined, a 3D geotechnical model was constructed to ensure that the targets were consistently achieved. The model is very similar to an ore reserve model; however, it is populated with geotechnical, metallurgical and blast index data. Through software queries the appropriate blast powder factor for each mining block can be obtained, thereby ensuring the correct fragmentation is blasted for the plant and mining operation. The initiative has delivered significant results showing improvements across the mine to mill value chain. These include increased loading rates, reduced electricity and crushing consumables, as well as higher plant throughput. Additionally, the initiative has benefited both brownfield and greenfield projects on the PPRust operation

Jan 1, 2006

By D. J. Reddish

An understanding of the mechanisms that cause large seismic events in a deep mine provides a foundation for designing effective measures to reduce the incidence of these events, as well as reduce the potential for damage arising from these events. The work described in this paper focuses analytical efforts on major recognizable and controllable factors that influence mining-induced seismicity and serves to screen out many of the more random aspects of individual events. Information used in this study was developed in the course of a long-standing rock burst research program conducted by the U. S. Bureau of Mines in cooperation with mines in the Coeur d'Alene Mining District and regional universities. Information was collected on 39 seismic events having local magnitudes greater than 2.5 that occurred between 1989 and 1994. Five major types of events were developed from these data that describe all but two of the 39 large events. The characteristic mechanisms, tint-motion pattern, damage pattern, and relationships to mining and major geologic structures were defined for each type of event. This information provides a foundation for assessing whether or not changes in mining activity aimed at reducing one type of rock burst will increase the incidence of other types.

Jan 1, 1996

By Ira Sohn

This article revisits global projections made in 1981of eight metallic and fertilizer minerals for the year 2000. The objectives here are to quantify the differences between the projected and observed levels of consumption for the year 2000 for eight of the 26 nonfuel minerals covered in the earlier study. An attempt is then made to attribute these (often) large differences to the major determinants of minerals demand — income, technological, regulatory and other policy changes, and changes in the recycling rates of the metallic minerals. The eight minerals covered are aluminum, copper, iron, mercury, nickel, phosphate rock, potash and tin. This summary article presents the actual population, gross domestic product (GDP) and per capita GDP changes from 1970 to 2000, compared with the projected rates for these important determinants of mineral use, along with the observed growth rates of minerals consumption for the eight nonfuel minerals included in this study. When the projections are compared with the observed global consumption levels for the year 2000, the differences range from +43 percent for nickel to +229 percent for potash.

Jan 1, 2005

By Hans Korfmacher

Product take-back regulations implemented in Europe have presented significant challenges to the consumer electronic product and battery industries. Initially companies established single compliance organizations within individual Member States. These programs met business needs but were inefficient and costly. They were protected from pressures of marketplace competition and could not leverage economies of scale. In order to address these problems P&G, Hewlett Packard, Sony and Electrolux conceived a pan-European compliance organization to collect waste electronic equipment Europe-wide. This organization, called the European Recycling Platform (ERP), operates in competition with existing national compliance systems. Since 2005 ERP has collected 800,000+ tons of waste electronic products and delivered millions of dollars in cost savings. This presentation reviews the steps needed to establish successful competitive collection organizations that provide sustainable recycling at the lowest cost.

Jan 1, 2010

By A. A. El-Midany

Traditionally, the choice amongst different upgrading techniques or in finding the optimum operating conditions for a given upgrading technology depends on whether one is looking at the grade or the recovery of the valuable mineral in the concentrate. In fact, the conclusions are not usually the same. This is because the best technique or optimum operating conditions for the highest grade are not the same as the conditions to achieve the maxi-mum recovery. Therefore, a unique measure that takes into consideration both grade and recovery is urgently needed. Finding such a measure is the objective of this paper. A proposed measure provides a selectivity index in the range of 0 to 1, where 0 is no selectivity and 1 is ideal selectivity. The index can be obtained by plotting the so-called Fuerstenau upgrading curve, which relates the recoveries of the components in products of separation and a running regression applying a one-parameter equation. The measure was applied to assess the selectivity of selective flocculation under different operating conditions when used as a sensitive upgrading technique for ultrafine ground ores. After applying the proposed selectivity measure in the case of the selective flocculation of ultrafine Egyptian iron ore without the addition of cations, it was found that the optimum conditions are pH 11, 1 kg/t sodium silicate and 0.4 kg/t potato starch with a selectivity index of 0.55. With the addition of cations, the optimum conditions were found to be pH 11, 1 kg/t sodium silicate and 2 kg/t potato starch with a selectivity index of 0.65. It should be noted that determining these optimum conditions using the traditional grade or recovery measures was highly ambiguous.

Jan 1, 2008

By J. M. Goris

The U.S. Bureau of Mines is conducting research on cable bolt ground supports to assess their material and support properties, to provide design criteria for using cable bolt supports as roof control systems under various types of underground mining conditions, and to develop a mathematical model of cable bolt support systems. Part 1 described laboratory studies of the support properties of conventional steel cable bolts. Part 2 describes the strength characteristics of conventional cables with steel buttons, single and double birdcage cables, and epoxy-coated cables.

Jan 1, 1991