Search Documents

By V. Labiouse, R. Gärber

The paper aims at clarifying the up-to-now misappreciated role taken by pore water on the design of deep tunnels in saturated porous media. Numerical simulations with a non-dimensional FEM-model emphasise the influence of pore water characteristics (in situ pressure and compressibility) and boundary conditions (lining permeability) on the short and long term underground-structure equilibrium states. These results cannot be achieved by means of monophasic total stress analyses. Dieser Beitrag untersucht den Einfluss des Porenwassers auf die Dimensionierung von tiefen Tunnelbauwerken in wassergesättigtem Untergrund. Numerische Simulationen mittels eines dimensionslosen FEM-Modells betonen den Einfluss der Porenwassereigenschaften (in-situ Druck und Kompressibilität) und der hydraulischen Randbedingungen (Tunnelausbaudurchlässigkeit) auf Kurz- und Langzeitverhalten des Untergrund-Ausbau Gleichgewichts. Diese Ergebnisse können nicht ermittelt werden anhand von Einphasen- und Totalspannungsmodellen. L’article s’intéresse au rôle méconnu de l’eau interstitielle dans le dimensionnement de tunnels profonds creusés dans des milieux poreux saturés. Des calculs adimensionnels par éléments finis soulignent l’influence des caractéristiques de l’eau interstitielle (pression in situ et compressibilité) ainsi que des conditions aux frontières (perméabilité du revêtement) sur les équilibres court et long terme de l’ouvrage. Ces résultats ne peuvent pas être obtenus par des calculs en contraintes totales.

Jan 1, 2003

By Cassandra A. Wetzel

Rock socketed mini-piles are a desirable foundation alternative when design capacity is more than 40 tons and there is limited access. In this case history mini-piles were designed to support between 75 and 200 kips at 12 locations adjacent to a perimeter wall, a party wall and at cast iron column piers. Limited geotechnical information, low overhead clearance, and active building population tested the creativity of the team to get the piles installed. The key geotechnical concern during installation of the mini-piles was the presence of a glacial till layer above the bedrock surface that restricted the seating of the casing into bedrock with a track mounted drill rig. Soil loss during the advancement of the rock socket using an air hammer was excessive and increased the risk of subsidence. Over a three week period the engineer worked with the contractor to modify the design, means, methods, and materials to install piles with adequate load capacity. This paper will present the changes in design and construction methods that were required.

By Dale S. Preece

A Discrete element computer program named DMC @istinct Motion Code) has been developed for modeling rock blasting. This program employs explicit time integration and uses spherical or cylindrical elements which are represented as circles in 2-D. DMC calculations have been compared with measurements on bench blasts in the field with relatively good comparison. Structural rock mass characteristics have a significant impact on any blast and DMC has not, until now, included these effects. This paper discusses a recently added DMC capability for treating joints and bedding planes in bench blast simulations.

Jan 1, 1995

By P. W. Godbehere, B. W. Brooks

"This paper deals with the milling of slags from the Noranda Continuous Process, in the Horne Concentrator at Noranda, Quebec. The milling of copper slags, although novel in Canada, has been practiced in Japan, Finland and elsewhere for several years.In March 1973, the prototype Noranda Continuous Process furnace or ""reactor'' came on-stream, In this pyrometallurgical process (see Fig. 1), copper concentrates mixed with flux are smelted in a single furnace to form copper or a high grade copper matte, and slag. The conventional smelting processes of roasting, reverberatory smelting and converting have been incorporated in a single 17 ft. diameter by 70 ft. long steel cylindrical vessel (l, 2). The copper or matte is tapped from the bottom of the reactor into ladles and transferred to an anode furnace or to a converter. The slag is tapped into 40 ton capacity ladles, cooled, crushed, and conveyed to the concentrator. At the present time, the reactor is operated to produce matte. The matte slag* containing 4 - 6 per cent copper is milled using conventional ore dressing grinding and flotation equipment. A flotation concentrate assaying 35 - 40 per cent copper is recycled to the reactor. Crushing, conveying, grinding, flotation and tailing disposal equipment previously used for over 40 years for ore treatment has been modified to suit the requirements of slag milling. Slag milling is essentially the scavenger circuit of a pyrometallurgical process."

Jan 1, 1977

By Wm. Ross Wayment, Innes P. Grantmyre

INTRODUCTION It has been recognized for some time that major changes in mining methods will be required in the near future. Two types of factors contribute to this need for change. Intrinsic factors include ground control problems associated with mining at increasing depths, noise, dust, toxic fumes, and logistics problems which arise from operation in a cyclical fashion. Extrinsic factors include competition for labor from industries offering safer and less difficult work, pressure for less impact on the environment, and changing economic and political conditions. The search for new mining methods has resulted in extensive research being carried out on such novel approaches as thermal fragmentation, high-pressure water jets, sonic drilling, microwave fragmentation, and laser cutting, among others. Joy Manufacturing Co. has elected to concentrate on impact breaking in stopes as a first generation continuous hard rock miner. IMPACT BREAKING Fragmentation techniques show a drop in specific energy as efficiency improves. Specific energy is the energy consumed per unit volume of rock removed and is affected by such variables as rock material properties, fragmentation method used, operator skill, tool design, etc. Mechanical fragmentation methods generally have specific energies much lower than that of the more novel methods. Table 1 shows impact breaking to have an efficiency exceeded only by that of drill and blast methods and it is this high efficiency which led Joy to impactors as the subject for research on potential mechanisms for continuous mining in hard rock.

Jan 1, 1976

The minerals industry consumes billions of dollars in raw materials, equipment, tools, services and chemicals. The industry, though, has turned overmuch of the research and development (R&D) for these products to manufacturers and suppliers. Now the industry and its suppliers must decide how much R&D the mining industry should be responsible for and what role the suppliers should play. Promoting R&D As a result of the current environment in the mining and minerals industry, there has been a substantial decrease in R&D. Depressed prices, stagnant growth, cost cutting and rationalization are evident.

Jan 1, 2000

By J. Chae, D. Pecha, R. Andrews

The Henderson/ML King CSO Project is a major combined sewer overflow (CSO)reduction project for the Department of Natural Resources and Parks of King County, Washington. The central element of the project is the 3100 lineal feet long, 14'-8"diameter 42nd Ave S Storage/Treatment Tunnel. During the course of the project, the owner and consultants evaluated numerous elements of the tunnel including the alignment, geotechnical conditions, tunnel liner, and settlement monitoring requirements. The contractor utilized innovative shaft construction methods for the tunnel portals, and adhered to strict contract requirements in successfully constructing the tunnel. This paper provides an overview of the design and construction elements of the 42nd Ave S Storage/Treatment Tunnel that led to the successful completion of the project.

Jan 1, 2005

By J. P. McCullough

In 1943, the Federal Bureau of Mines began a program of thermodynamic investigations of petroleum constituents and related compounds. These systematic, long-range studies, which were conducted in the thermodynamics laboratory of the Bartlesville Petroleum Research Center and are still continuing, have resulted in a substantial quantity of data valuable to the petroleum industry and science in general. As separate phases of these studies were completed, the findings were promptly reported in the scientific press. During the past 16 years, 89 journal articles, giving the results obtained for individual compounds and small groups of related compounds, were published, mainly in the Journal of the American Chemical Society and the Journal of Physical Chemistry. In addition, members of the Bureau staff have contributed six chapters to specialized reference books. This circular, prepared in response to many requests, lists these 95 published papers, giving an abstract of the contents of each, as well as titles, authors, and literature citations. The journal articles are listed in the order of their preparation, which closely approximates the chronological order of their publication; hence, the item number to the left of each citation corresponds to the assigned contribution number. For the convenience of the reader, the abstract section is followed by a condensed bibliography, arranged alphabetically by senior author and keyed to the abstracts by appropriate contribution numbers in parentheses after the entry.

Jan 1, 1961

By M. Karmis, C. Haycocks

The evolution of longwall mining is briefly traced from its inception in England in the 1620's. In the beginning this method recovered 90% of coal with roof closure controlled by packs and walls. Mechanization began with kerf cutting, crude face conveyors, and improved face support. Full face mining was accompanied by the introduction of self- advancing hydraulic supports. U. S. longwalls evolved a retreating system to recover blocks of coal outlined by room and pillar panels. Computer control combined with the most modern technology have greatly increased productivity. Past trends are used to predict future technological directions.

Feb 24, 1997

By K. V. Phani Prabhakar, G. Padmanabham1, L. Subashini

Laser-arc Hybrid Welding (LAHW) is a relatively recent concept which effectively combines the advantages of laser welding such as the high depth of penetration, low heat input, high welding speed and the positive aspects of arc welding such as better edge bridging and possibility to add filler. For example, steel sections upto 12 mm thickness have been successfully welded in a single pass at a welding speed of 1 m/minute using a 3.5 kW CO2 laser in combination with a MIG arc. Maraging steel of grade M250 is widely used in the aerospace industry in thicknesses upto 10 mm. Conventionally, it is possible to MIG weld such thicknesses in 3-5 passes employing V-Groove joint preparation. However, this multi-pass welding results in formation of reverted austenite in the weld zone after post weld aging; and the high heat input widens the reverted austenite containing heat affected zone which is popularly known as the dark zone/eyebrow zone. Both these zones are detrimental to strength of the welded joint, specifically the fracture toughness. The width of the dark band is an important factor because, thinner the band, it is supported more effectively by the surrounding material. Therefore, in order to avoid multi-pass welding and reduce the overall heat input, single-pass laser-MIG hybrid welding was attempted on 10 mm thick maraging steel M 250 plates using a hybrid laser arc welding system comprising a 3.5 kW CO2 slab laser and a MIG welding system. Simultaneously, multi-pass MIG welds also are produced. Both the laser-MIG hybrid and MIG welds are characterized microstructurally and subjected to mechanical tests such as tensile and fracture toughness in as-welded and post weld aged condition. The amount and distribution of reverted austenite in the fusion zone and width of the dark band was found to be different. Hybrid welds showed a narrow dark band zone and improved mechanical properties. Laser-hybrid and MIG welding investigations carried out on thick section maraging steel M 250 will be presented in detail, including microstructure, tensile properties and fracture toughness of the welds. To the best of the knowledge of the authors there are no reports on laser-MIG hybrid welding of maraging steels.

Jan 1, 2014

By Paul C. Hyndman

Three properties in the Tuolumne River RARE II area, the Eagle Bluff Mine (lode) and the Indian Creek Bar and Bossy Bar Prospects (placer), have identified subeconomic gold resources (table 1). Nineteen other properties have potential for gold resources. Adjacent to the study area, five properties have identified mineral resources, and nine others have potential for resources. Properties having high-grade zones (shoots), but licking enough tonnage to be classified as resources, are listed in table 2. Gold, in lode and placer deposits, is the principal mineral commodity in the Toluene River study area. Ten properties within the RARE II boundary have gold-rich zones or shoots; they range in size from 12 to 2,500 tons and in average grade from 0.09 to 0.97 oz gold per ton.

Jan 1, 1983

By Q. G. Reynolds

Keywords: Pyrometallurgy, furnace, DC, reverse polarity, dual-electrode The dual-electrode direct current (DC) arc furnace uses two graphite electrodes, one connected as cathode, and one as anode. Such an arrangement avoids some of the design difficulties associated with the anode hearth traditionally used in single electrode and twin-cathode DC furnaces, but can introduce other design and operational difficulties including deflection of the arcs toward the furnace walls. Counter-intuitively, both arc jets in a dual-electrode furnace travel from the electrode down to the bath surface, despite carrying electric current in opposite directions ? this is suggested in the theory of the governing equations of arc formation, and confirmed by experiments using high-speed photography. The dual-electrode arc system at small pilot-plant scale is studied using a transient magneto-hydrodynamic model capable of predicting arc deflection and interaction from first principles, and the results are compared to the behaviour of twin-cathode systems at similar power. Finally, a simple arrangement of the furnace busbars, M configuration, is shown to provide some passive protection against arc deflection.

Jan 1, 2011

By R. J. Jewell

The storage capacity of any given tailings storage facility (TSF) is a function of the volume available for the tailings, for which the geometry of the final upper surface of the tailings is most important. One of the advantages that can be obtained from thickening tailings prior to discharge is that the tailings can be stacked at a steeper beach angle than is obtainable with conventional low-density slurries. However, there is at present no universally accepted method available for the accurate prediction of tailings beach slopes. This paper examines the current situation with the objective of putting the quest for a method for the accurate prediction of beach slopes into perspective. The paper references published reviews of the best-known beach slope prediction methods. However, there do not appear to be any independently verified projects or published references to projects on which a Class A prediction has been validated for any of these approaches, and in those instances where projects have been implemented correlation of actual with predicted slopes has been poor - often due to differences between the properties of the tailings assumed in the design and those actually achieved in the field. The author also concludes that flume-scale testing cannot be taken as a reliable indicator of full-scale performance, and suggests that the outcome of any current predictive method should be used by experienced practitioners as only one of a range of indicators in order to suggest a range of slope angles likely to result for any given operation. Practice has shown that it is possible to manipulate beach slopes by changes to the disposal technique, such as limiting the rate of discharge per discharge point and by increasing or decreasing yield stress, but the impact of these changes cannot readily be predicted. There are also newly emerging technologies, such as the injection of a polymer into the tailings at discharge, that will enhance the dewatering of tailings and hence expedite the consolidation of the tailings, that could well facilitate the development of steeper beach slopes. The overall conclusion is that with the current state of knowledge, the accurate prediction of beach slopes is not possible. Furthermore, in view of the inherent variability of the tailings parameters from any operation, it may well be of more value to concentrate on developing an understanding of the means by which the tailings parameters may be manipulated by the operators to achieve a given beach slope than to concentrate wholly on developing a generic beach slope prediction model.

Jan 1, 2012

By C. Musingwini

An often overlooked factor in the analysis of mine layouts and schedules is technical operating flexibility (or tactical flexibility), mainly due to its nebulous nature. By glossing over technical operating flexibility the resultant mine layouts and schedules maybe suboptimal. The need to incorporate technical operating flexibility into the analysis and comparison of mine layouts and schedules is increasing in importance. The nature of technical operating flexibility is illustrated, previous work on valuing of operating flexibility reviewed, and a proposal made on how technical operating flexibility can be quantified for tabular reef mines by using a platinum reef deposit as a case study. Once technical operating flexibility has been quantified it becomes possible to explore its incorporation into the analysis of mine layouts and schedules and subsequent optimization processes. This paper is a revised version of a paper presented in the Proceedings of the Second International Platinum Conference, ?Platinum Surges Ahead? in 2006. The work described in this paper is part of a current PhD study at the University of the Witwatersrand. Keywords: mine plans, layouts, schedules, technical operating flexibility/tactical flexibility, ore availability.

Jan 1, 2007

By W. G. Davenport, M. Paneni

Experiments in sheets of mercury and water have confirmed that the dynamics of bubble rise are simi-lur in Liquid metal and aqueous systems. RECOGNITION that bubble/metal interactions are important in pyrometallurgical refining processes (e.g., steelmaking, vacuum degassing, deoxidation of copper) has led to a number of investigations into the dynamic behavior of bubbles rising in liquid metals. Terminal velocities of bubbles rising in mercury (20°C)' and silver (1000" to 1050"c)1,2 have been measured. Good agreement between aqueous and liquid metal systems has been obtained. Shapes of air bubbles rising in mercury have been determined experimentally by Davenport, Bradshaw, and Richardsonl who used a system of electric probes to measure maximum horizontal and vertical dimensions, Fig. 5. In the present work the motion and shape of nitrogen bubbles rising in a thin sheet of mercury (i.e., a "two-dimensional" environment) have been studied with the view of confirming dynamic similarity between aqueous and metallic systems. The use of thin sheets of liquid permitted direct visual and photographic comparisons of bubble behavior in clear liquids and in mercury. EXPERIMENTAL METHOD The thin sheets of mercury or water were held in a clear acrylic plastic container, Fig. 1. The sheets of liquid were 80 cm high by 30 cm wide and 0.47 cm thick. Single bubbles were formed by injecting the desired volume of nitrogen into an inverted semicircular cup (stainless steel). The cup was then rotated into the upright position using an external handle thus releasing a single bubble of measured volume. Nitrogen was injected into the cup from a nitrogen cylinder through the external handle and a hollow rotating axle. The volume of a bubble (volume range 0.01 to 10 cu cm) at any instant was obtained by connecting a soap film meter to a small gas space above the liquid. By this technique any change in the volume of a gas bubble in the liquid (i.e., during cup filling or during rise) produces an equivalent displacement from gas space A into the buret B. This displacement is determined by measuring the movement of a horizontal soap film in the buret. Bubble shapes were determined using single-frame photography. Rising velocities were determined by cinephotography with a 1/100-sec stopwatch in the field of view. In both cases dimensions were referenced to a rule attached to the container surface, also in the field of view. Linear dimensions were measured on projections of the single-frame negatives. Rising velocities were calculated from measured heights of rise (10 to 20 cm) and times of rise. The effects of disturbances caused by cup rotation and by bubble release were minimized by photographing bubbles at a point not less than 25 cm above the cup. MATERIALS Mercury: Technical-grade purified: minimum 99 pct Hg; Johnson Matthey and Mallory Limited, Toronto. Nitrogen: Technical-grade purified nitrogen: 99.99 pct Nz, 0.01 pct 02, trace argon; Air Liquide Canada Limitee, Montreal.

Jan 1, 1970

Performance of Dry Separation Processes in Cenospheres Recovery from Coal Fly Ash

Sep 13, 2010

By Ray Brandon

The recent introduction of polymer geogrids for ground control purposes in underground mines allows mine operators more flexibility in choosing improved products for several applications. This is evidenced most clearly in longwall recovery operations. Since November, 1994, many mine operators have chosen Fortrac geogrid assemblies for the purpose of securing longwall recovery areas prior to shield removal. Fortrac is a lightweight, strong, and flexible polyester geogrid available in many strengths. Utilizing the "diamond" seaming method, different strengths of Fortrac geogrids are easily fastened together so stronger geogrids may be placed in the most critical areas and lighter geogrids in less critical areas.

Jan 1, 1996

By Steve Kral

Improved metals and other commodity prices have caused the mining industry to open new mines, re-evaluate development opportunities at potential mines and increase production at existing ones. This sense of renewed optimism is being seen at operations and development projects around the world. Except in the United States. The regulatory structure there has not allowed the domestic industry to share much in mining’s resurgence. It can still take up to 10 years to permit a new mine. And, while Clinton-era regulations regarding mill sites have been put on hold, existing mines that wish to expand operations still face significant regulatory and environmental hurdles. But things may begin to improve in the United States.

Jan 1, 2005

By Hou Shitao

With the development of Wuhan's city planning in China, new buildings of moderate and high store have been increasing day by day. Precast concrete piles or cast-in-site piles were used in the major foundations of the buildings. In process of their design and construction geotechnical engineers are concerned very much about practical bearing capacity and construction quality of pile foundations. In order to grasp accurately the cases static loading or vibration test is used generally to judge them. At present, the major questions in existence are that although a load is applied directly on pile and measured datums are reliable for static loading test, it must take a lot of work and longer time and engineering cost is higher. A vibration test has the advantages of which checking up of pile quality can be performed rapidly, the test is simple and convenient, and scope measured wide. But bigger error exists generally in measured datums. Therefore, it is nesessary to make vibration test on piles more perfect for pile foundation engineering. It is stated in paper that adapted technique of vibration test on piles is quite right in developmental direction sense for pile foundation. There are a great variety of vibration test methods on piles. A few of methods which often are adapted in practice can not meet the need of different practical engineering. It is also an important question whether the instruments of vibration test and relevant computer softewares make a response accurately for practical case. Different sequence of operation and technical requirements comes into being some influence directly on the test results. Meanwhile, different combination of soil stratigraphy, soil texture, groundwater and pile could cause different error of test datum. It is necessary to analyse and judge objectively the results of vibration test. Therefore, on the basis of developing and perfecting further the technique of vibration test, the applied technique of vibration test should be standardized so that better test results can be obtained.

Jan 1, 1991

By Wils L. Cooley

Although electric utility companies have been active in grounding and bonding within substations, the mining engineer or mine electrical engineer is not involved to the extent that he can be fully up-to-date on the most effective practices for substation construction. The coal mine power system is grounded in a fundamentally different way from most other industrial power systems and is subject to considerable Federal and State regulation. At this time, there is little information that is directly applicable to the mine situation, especially if the substation must be built in an area of limited size or in low-conductivity earth. The objective of this guide is to provide specific engineering information to the mining; industry. Using as little theory as possible, it was written to be general enough to cover most substations, but specific enough to provide direct help with each substation. It will attempt to recommend practice that is in agreement with present Federal rules and regulations.

Jan 1, 1980