Search Documents

By Antonio Karzulovic, Ricardo Sepulveda, Manuel Schellman

Mantoverde Division of Empresa Minera Mantos Blancos S.A., Anglo American Chile, developed an open pit mine to exploit copper oxide ore. Mantoverde mine is located in the Province of Chañaral, Northern Chile, about 1,020 Km far from Santiago. Currently, the East wall of the mine is reaching the condition of final pit. To evaluate the possibility of a pit optimization on this wall a geotechnical study was performed, including slope stability analyses by limit equilibrium and numerical methods. As a result of this geotechnical evaluation, it was decided to allow a probability of failure of 12% for instabilities affecting up to 600,000 tonnes, and use steeper slopes on the East Wall of the mine. This paper describes this geotechnical evaluation and how the results of the stability analyses were used to define a flexible slope design, which allows modification if the observed slope behaviour deviated from the expected one.

Jan 1, 2006

By Murray Wood, Michael Schaffer, Makat Katom

"An expert system applied to the control of mineral process unit operations is, by its nature, the site best operating practice, having been designed by the local experts in conjunction with consulting metallurgists. The “common sense” layer in a MET (MinnovEX Expert Technology) solution determines an appropriate action for the current operating conditions through a developed heuristic model of the process (expert system). The magnitude of the setpoint change that is made is proportional to the confidence that the system has in its interpretation of the current conditions (fuzzy logic). The solution is always striving to take the process to a constraint and thereby optimise the operation. An accepted limitation of the solution is that the only way the system can determine if a constraint has been reached is to exceed it and then withdraw – essentially “experimenting” with the process. By leveraging a model, which can accurately ""simulate"" the process, this restriction can be circumvented by pre-testing the set point change through a ""what if"" analysis and then modifying the solution as appropriate.At Ok Tedi, the introduction in 1999 of a MET expert system for SAG milling resulted in significant improvement in circuit throughput. Yet, with the additional inclusion of an accurate model of the process there was still more that could be achieved. Hence, in 2002 a MET Neural Network model was developed and deployed to enhance the existing expert system solution. The principal objective of this model was predicting the effect that changes in SAG tonnage and density would have on the power draw of the mill - essentially a power predictor. The results have seen a decrease in process variance with an associated increase in average circuit performance.This paper describes the methodology by which the Neural Network model was implemented, the considerations and limitations when applying this technology and ultimately the results that were achieved."

Jan 1, 2003

By G. Coombs, L. Meade, J. Welshimer

Industrial Minerals commodity profiles are continued from May's Annual Review issue. Diatomite G. Coombs, Manville Sales Corp. Growth in US diatomite production continued to lag in 1986. The US Bureau of Mines estimated that 580 kt (640,000 st) were produced last year. This is a 1%0 growth over 1985. The cumulative growth from the 1982 low point is 4.4%. Present production, though, is still only 90% of the high tonnage of 1979. The industry will see increased competitive activity with the start-ups of two new mines and production facilities in California and Oregon. US production has come primarily from Lompoc, CA, Bassalt, Clark Station, and Lovelock, NV, and Quincy, WA. New production, probably with capacities of 45 kt/a (50,000 stpy) each, have started near Burney, CA, and Vale, OR. Eagle Picher's new, full-line filter aid and filler plant at Celatom, Vale, OR, was dedicated in August. The plant uses diatomite from the Celatom mining district in Juntura, OR. Grefco's new filter aid and filler plant near Burney, CA, was ready in July. It produced flux calcined products through a single kiln and can handle both bag and bulk shipments. The operations are in Shata County with the plant and mine at the same site. Manville Specialties Group is moving its Filtration and Minerals Division headquarters and research staffs to Lompoc, CA. The move is intended to strengthen response and performance by locating research, marketing, and production close together. Diatomite is processed in three methods: natural, calcined, and flux calcined. The natural is dried to remove water and is particle size classified. Calcined or straight calcined products have been sintered to modify particle size or permeability. Flux calcination, or flux sintering, has a stronger influence on permeability and also benefits color. The unique structure of diatomite is used in a range of particle sizes from fine paint fillers, to coarser filter aids, to granular aggregates. Dimension stone L. Meade, Geomapping Associates Ltd. 1986 was another good year for dimension stone production. The trend toward using marble, granite, limestone, sandstone, and slate has created an increasing demand. According to US Bureau of Mines 1986 estimates, 1.1 Mt (1.2 million st) of dimension stone, with a value of $173 million, was produced by 200 companies. This is an increase from 1985, where 220 companies produced 1 Mt (1.12 million st) valued at $172 million. The increased production volume and decreased unit value is due to the competition from imports. The net import reliance in 1986 was 68% compared to 62% in 1985. The value of imports was $374 million in 1986 versus $295 million the year before. In an effort to maintain their market share, domestic finishers, particularly in the granite industry, continued to upgrade plants and machinery during 1986. In addition, offshore dollars have financed a number of fabricating facilities in North America that will finish imported rough stock. It is hoped that this increased domestic production capability will capitalize on a devalued US dollar. The trend has been for growth in stone usage and market. This trend is continuing with increased public awareness and desire for natural stone in buildings. The area of greatest market growth is expected to be in residential and interior decorative stone usage. Use of sophisticated, automated equipment has made the cost more affordable. Now lobbies, foyers, and specialty rooms are being clad in stone. Dolomite J. Welshimer, National Lime & Stone Co. About three-quarters of dolomite production is used as construction aggregates and 10% to 20% is sold or used as an industrial mineral. Total limestone and dolomite consumed for chemical and metallurgical purposes is about 136 Mt/a (150 million stpy). Sales of industrial dolomitic products were somewhat stronger in 1986 than levels recorded in the early 1980s. Some of the sales' strength, however, can be attributed to reductions in the number of active mining and processing operations. The industry will probably undergo further consolidation by the end of this decade. This will be due primarily to the continued softening in demand by the steel industry. Dolomitic limestone deposits being mined for raw materials for the steel, glass, and refractory in¬dustries are generally 54% calcium carbonate and 45% magnesium carbonate by weight. Impurities composed of silicon, aluminum, iron, sulfur, and phosphorous, represent less than 1%. The heaviest concentration of high purity, surface mineable dolomite in the US is in northwestern Ohio. Crushed and sized dolomitic limestone is a basic raw material for the iron and steel industry. It is also used as feed stone or lime kilns. Soft-burned lime is a popular raw material for BOF steel production. It is also used extensively in insulating glass fiber manufacturing. A related material, hydrated

Jan 6, 1987

By F. Calizaya

The PT Freeport Indonesia‘s Deep Ore Zone(DOZ) copper deposit is located in the province of Irian-Jaya, Indonesia. Currently, a block cave mine is being developed around this deposit. Production is scheduled to start in year 2000 and to ramp up to25,000 tpd by year 2003. The air quantity requirement for this mine is equal to 780 m3/s. To supply this quantity, the mine will require five centrifugal fans (one 450 and four 750 kW fans). This study summarizes the technical aspects related to the installation and commissioning of one of these fans. The fan was installed on the surface in a parallel arrangement with two others. It has a design capacity of 240 m3/s of air at 2.2 kPa of static pressure. The study presents the installation details from the underground shaft excavation and portal development through fan testing and commissioning. It also presents the results of a monitoring system that was installed to determine the fan duties.

Jan 1, 2000

By Y. Ichihara, H. Matsumoto, K. Itakura, H. Eguchi, G. Deguchi, K. Sato

Mechanical data from a rockbolt drilling machine, such as torque, thrust, revolution and stroke, are useful for understanding the geological and geomechanical conditions around roadways and hence selecting the optimum bolt type and density. Laboratory experiments showed that the level of torque or thrust reflects differences in rock type, with separation of strata and cracks appearing as a specific pattern. Algorithms of neural networks based on adaptive resonance theory and back-propagation were used to extract the pattern and estimate the location of discontinuities. For field testing in an underground coal mine, a prototype data acquisition system was attached to a portable drilling machine. Several sets of logging data from one locality were combined to construct a two-dimensional model of the strata, from which the slope angles of discontinuity faces could be estimated

Jun 19, 1905

By M. Gallego, R. Oyarzun, L. Ortega

Evidence of metallogenic activity in an area dominated by Upper Precambrian and Palaeozoic metasediments was partially explained in the 1980s when drilling and a geophysical survey detected hidden intrusions, but questions remained to be answered about the nature of the fluids. Sb mineralisation at El Juncalon vein-type deposit was selected for geological, geochemical and fluid inclusion studies as a model with a relatively simple quartz-stibnite-pyrite paragenesis. Many of the characteristics were those of Chinese-type vein Sb deposits, which can be regarded as atypical of the epithermal type as they are hosted by clastic rocks

Aug 1, 1995

By A Hekmat, M Fuentes, F Armijo, R Castro, F Rodriguez

Interpreting the behaviour of granular material and simulating the gravity flow are complex processes in cave mining methods. In this paper, a new Cellular Automata based code – FlowSim – is used as a flexible tool to simulate the gravity flow and subsidence zone in block caving mines. The simulation results of the gravity flow model in a real scaled mine as well as a scaled physical model are presented in this study. In this research, FlowSim was first calibrated at a mine, based on the information obtained from smart markers. These markers were located in five points of the second block of the Esmeralda sector, at the El Teniente copper mine, Codelco, Chile. The calibration was performed with the objective of reducing the discrepancy between the extraction zone defined by markers in the mine and FlowSim outputs. Regarding the mine data, FlowSim was calibrated with the minimum error of ten per cent between real and simulated results. Then, the calibrated FlowSim model was used to simulate the flow behaviour of a scaled physical model. This model was constructed in the Block Caving Laboratory of the University of Chile to scale down the same block of the Esmeralda sector with the scale of 1:200. The FlowSim outputs show that this software enables the simulation of the gravity flow of the scaled model with less than five per cent discrepancy in grade and dilution entry to the drawpoints. According to the obtained results, this paper recommends FlowSim as an appropriate tool which can improve the design of production level in block caving and can enhance the prediction of the subsidence zone and dilution entry.CITATION:Castro, R, Hekmat, A, Fuentes, M, Armijo, F and Rodriguez, F, 2016. FlowSim – a versatile flow simulation tool to quantify extraction and design alternatives for block caving, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 645–652 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By A. Ochieng

Solids suspension influences the quality of mixing and energy requirement in a solid-liquid system, both of which determine the efficiency of industrial processes such as nickel precipitation. Nickel solids concentration distribution in a stirred tank was investigated using computational fluid dynamics (CFD) and experimental methods. The concentration distribution of the nickel solids was compared with that of sand and glass. The laser Doppler velocimetry (LDV) method was used to measure the velocity field for the liquid-only system and an optical technique was employed to determine the axial solids concentration distribution. Regions of in homogeneity in the tank were identified. It was found that, for a given solids loading, the solids concentration distribution depended on both particle size and particle size distribution. High solids loadings were investigated and a difference in the concentration distribution pattern was obtained with nickel, flint glass and sand particles. The CFD simulation results highlighted problems that could be associated with some conventional experimental methods of determining solids concentration distribution in a stirred tank. Keywords: nickel; CFD; simulation; mixing; solids suspension.

Jan 1, 2010

By Andrew Kaczmarek

The mining industry is enjoying a much needed and long awaited increase in demand for natural resources. However, consolidations in the mining and mining service industries, along with a generational departure of experienced industry professionals, is challenging today’s mining companies. These challenges are not only in maintaining their existing operations, but also in securing qualified resources for developing new projects. These challenges are compounded for junior mining companies. They oftentimes lack for operating properties to draw experienced professionals from. Also, juniors have to compete with the majors’ “mega-projects” for experienced project personnel from the reduced ranks of engineering companies. This article discusses some strategies developed by Anatolia Minerals Development (Anatolia) in developing its Çöpler gold project in central Turkey.

Jan 1, 2006

By Mario Aiezza

This paper outlines the results of a relationship developed during the design and construction of the foundations for the Gallery Towers project in Melbourne. Both the builder and the piling contractor were determined to arrive at a satisfactory foundation solution to the problems encountered at the site. The scope of piling work was to provide load-bearing piles under the building columns, some of which were located within a retention system that also required a piling solution. Geological conditions were variable and challenging. The site area was small and located adjacent to the National Arts Centre in the developed Southbank area, a high density office area. This presented logistical problems in limiting construction traffic on site and also demanding minimal noise and vibration emanating from piling activities. The piling contractor, Vibro-Pile, and the builder, Walter Construction Group, faced the challenges presented with a refreshing cooperative attitude that was beneficial to both companies. Commercial issues rising from design and construction problems were first put apart in order to allow the respective technical department of each company to work with minimum constraints to achieve the most cost effective solution. In the process usual adversarial attitudes resulting in loss of time and money was avoided. A number of issues were addressed successfully at minimum cost and time during this contract. Despite the difficulties encountered, the job was completed on time and with negligible claims for extras, resulting in the development of a strong mutual respect between both companies.

Jan 1, 2002

The first mention of gold in Western Australia was in 1848 when some specimens of copper ore, which are believed to have come from the Murchison district, were sent to Adelaide for assay. Gold was present in these specimens, but no particular interest seemed to be attached to this fact as the search at that time was mainly concentrated on base metals and coal. Interest appeared to be shown in gold in 1852 when several parties moved out eastwards from York looking for goldbearing country. Though these parties inmany cases were very near to what is now known as the Yilgarn Goldfield, nothing was found.The next record of gold was reported in some specimens which were brought in from Cardup, some 25 miles from Fremantle. Though this area was investigated, it would appear that all the gold had been contained in the specimens and nothing further was found, though the report had been the cause of a small rush of people interested in gold.From time to time specimens had been brought in by various people from the district east of Northam, and in 1861 a reward emanating from private sources was offered for the finding of gold within a radius of 150 miles from Perth. The Government at this stage took an interest in exploration for gold and in the same year supplemented this privately offered reward on a £ for £ basis. The Government also, about this time, commissioned a practical miner, with prospecting experience in the Eastern States, to examine the country between Albany and Northam with a view to the possible existence of goldbearing veins in that area. His report, however, was entirely unfavourable and nothing further was done. In 1873 a quartz lode was discovered near Albany arid a company was formed to work...

Jan 1, 1956

By Fredrick L. Johnson

The Bureau of Mines, under Congressional mandate, conducted a mineral survey on the Park Range WSA (Wilderness Study Area) in 1984 and 1985. The WSA, located about midway between Tonopah and Ely, encompasses 47,268 acres. No mineral resources were delineated, nor were workings found, during the investigation. There has been, however, exploration in and near the north end of the study area. ASARCO is actively exploring a block of 41 claims for hot-spring type, low-grade, large-tonnage gold deposits. Their claim block is almost entirely in the study area. The Morey mining district, 7 miles southwest of the study area, produced silver and lesser amounts of gold and lead sporadically from the mid-1860's through the mid-1960's. The WSA is underlain by Tertiary rhyolitic and latitic volcanic rocks and by Paleozoic sedimentary rocks. The Paleozoic rocks have been faulted, silicified, brecciated, and hydrothermally altered, and have anomalous concentrations of precious metals and pathfinder elements. Additional exploration in the north part of the Park Range WSA may lead to delineation of gold resources.

Jan 1, 1986

By J Kokado, N Hatta, S Yabushita

A theoretical model is described for prediction of the capacity of fines from porous ores, such as cokes and sintered ores, to be removed by a pneumatic, horizontal-type classifier prior to charging into a blast furnace. First, the influence of variation in the apparent density and drag coefficient of porous ores on removal efficiency is analysed from a stochastic standpoint. The effect on efficiency of collisions between particles in the classifying region is then examined analytically in relation to the ratio of the mass flow rates of particles and air (the loading ratio). Finally, a theoretical model is constructed that takes these factors into account. Theoretical and experimental results are compared and classifying efficiency is discussed from both experimental and theoretical viewpoints.

Dec 1, 1993

By Norman O. Lotter, Virginia Lawson, Mika Muinonen, Dominic Fragomeni, Jorge F. Oliveira

Development of metallurgical flowsheets from drill core to production of finished metal involves two main domains: process mineralogy to sample the ore and develop a successful flowsheet producing saleable concentrate; and extractive metallurgy to convert that saleable concentrate to finished metal. Effective flowsheet development for a new or brown-field concentrator and processing facility is essential to project schedule and return on investment. Over the last decade in particular, the integration of geology, mineralogy, sampling, and mineral processing have empowered the development of an improved practice in flowsheet development. The use of geometallurgical units as a basis for best-practice sampling delivers representative study material to the laboratory. Modern automated mineralogy characterises the whole rock assembly and paymetal mineral hosting, to address downstream process implications. Batch scale flotation testing then uses this information to design and perform well-focused strategies. At early stages of the project, the Extractive Metallurgy team is engaged to determine processing constraints or other economic drivers in conversion of the saleable concentrate into finished metal. The team evaluates available technologies, assesses the impurities and key properties of the given concentrate. In many cases, changes to mineral processing flowsheet are required to maximize value per tonne of concentrate. Site conditions, availability of infrastructure, energy and power all play an important role. Modern metallurgical simulation tools such as FactSage™ and METSIM™ can quickly define the appropriate test program for each process. Bench scale testing and appropriate scale of piloting can confirm simulations and provide design criteria. A case study demonstrates how effective use of these tools and a multidisciplinary team can accelerate flowsheet development, while reducing costs and ensuring that the designed processing facilities maximize project value with minimum risk.

Jan 1, 2014

By M. Hitch, M. B. Lytle

Resource development conflicts arise largely due to differences in worldview between those who support and those who oppose development. This paper illustrates how societies and civilizations with different worldviews produce different levels of creative and economic energy. A questionnaire was created to build a database of responses to test whether worldview and resource development are correlated. Factor and multivariate regression analysis determined correlations for respondent groupings. Results showed a positive correlation between the respondents\u2019 worldviews and their attitudes toward resource development. Correlations became stronger as the homogeneity of the sample subgroups increased.

Jan 1, 2017

By Kjell Karlsrud

"Abstract New semi-empirical design procedures for the determination of ultimate shaft friction and load-displacement response of axially loaded piles in clay are proposed. Hereunder also prediction of how the capacity will build up with time following the pile installation, primarily as result of reconsolidation. A main basis for developing the new procedures was detailed review and re-assessment of results from a series pile load test programs published over the past 30 years on piles well instrumented to monitor soil- and pore pressures as well as load distribution along the pile shafts. Two new alternative procedures are proposed for predicting the ultimate shaft friction; a-approach using the normalised undrained strength based on direct simple shear tests as a main correlation parameter, and ß-approach using the overconsolidation ratio, OCR. Both approaches include the effects of the plasticity index of the clay, Ip, which is shown to have an especially large impact on the correlations when Ip<25. It is recommended to use both methods in design practice, and select design values for the ultimate shaft friction that represents an average for the two methods. Pile diameter, length or stiffness, or whether the pile is open- or closed-ended seem to have little impact on the shaft friction. However, a moderate effect of pile length or flexibility on the total ultimate pile capacity comes out of the proposed t-z curves, which include some post-peak reduction. The proposed procedure for predicting the time for set-up is based on linear radial consolidation theory. The main input parameters are the insitu permeability and virgin modulus number (or virgin compression index) of the undisturbed clay. The same basic formula and correlations are applicable to both open and closed-ended or partially plugging piles.IntroductionThe design procedures presented herein are primarily based on observations and data collected in connection with “fully instrumented” pile testing programs that the author has been responsible for or has become involved with over the past 40 years, or that have been found in the literature.It was a pre-requisite for the test programs included that there were sufficient high quality soil data available to give a reliable determination of the true in-situ strength and compressibility characteristics of the clay deposits. The soil conditions range from soft NC clays with undrained shear strength down to about 15 kPa, to very stiff clays with undrained shear strength up to about 500 kPa and OCR up to 25. The plasticity index of the clays mostly lies in range 12 to 60 %."

Jan 1, 2014

By Wing G. Agnew, John A. Johnson

"INTRODUCTION This paper is one of a series being published by the Bureau of Mines pertaining to an investigation on the use of stemming in metal mines now being conducted at the Mount Weather Testing Adit. Its purpose is to compare the amount of dust and gases produced as a result of blasting charges of dynamite (1) in drill holes, (2) in bombs, and (3) in mud-cap or adobe shots.ACKNOWLEDGMENTSValuable assistance and advice on stemming were given by members of the staff at the Bureau of Mines, as acknowledged in previous publications. 4/TEST PROCEDUREThe results used for comparison in this report are from dust and gas samples taken after blasting (1) four regular test rounds with no stemming, (2) five bomb shots, and (3) two mud-cap or adobe shots.The four rounds were the standard 26-hole test rounds designed to break 4 feet of rock. The procedure for drilling and blasting these rounds is described in Report of Investigations 3509.Before the regular test rounds were blasted, about 1,200 bounds of fine rock was placed on the steel mucking sheets that covered the end of the adit track; the wails, hack, and floor of the adit were washed thoroughly; and the fine rock on the mucking sheets was completely wetted.Each of the 5 bomb shots consisted of 10 sticks of dynamite tied together and hung at midpoint of the adit, 8 feet from the fall."

Dec 1, 1942

By Roy T. Sorensen

As part of its mission to maintain an adequate supply of minerals to meet national needs and maximize mineral production from domestic sources, the Bureau of Mines is investigating the recovery of alumina by hydrochloric acid leaching of kaolinitic clay. Most iron impurities are leached from the clay along with the alumina and must be removed before or during crystallization to aluminum chloride hexahydrate. The thermal decomposition step then provides an alumina product of acceptable iron analysis. Miniplant studies of a Bureau-developed solvent extraction technique, using a tertiary amine in kerosene diluent, have demonstrated that the iron content in aluminum chloride leach liquors can be reduced to levels of less than 0.007 wt-pct (7 ppm), expressed as Fe203. Entrained and dissolved organic matter in the purified pregnant leach liquor from the solvent extraction circuit can be reduced to less than 2 ppm by using a fabric-packed coalescer and subsequent activated carbon treatment. Investigators discovered that a steady buildup of zinc accumulated in the solvent phase within the extraction circuit, proportional to the amount of leach liquor treated. The solvent phase zinc analysis increased by 0.01 wt-pct ZnO for each 1,000 gal of pregnant leach liquor purified.

Jan 1, 1981

By C. H. Titus

This study consists of four descriptive Sections covering respectively: a state-of-the-art literature survey on ungrounded and grounded power systems, a report on literature pertaining to human threshold limits of electric shock, an analysis of the performance requirements of isolated systems and a section on design and performance specifications for an isolated system the final section includes copies, and translations where applicable, of the most important articles on foreign mining practice as well as some technical publications which could be difficult to obtain elsewhere. Section 2 - Literature Survey In analyzing the available literature on ungrounded systems it became apparent that too strict an interpretation of Section 1.1 of the Contract would limit the survey in both period of time analyzed and in available literature which discussed several types of power systems. Therefore, the survey was expanded to cover approximately the past twenty-year period and to cover literature which addressed itself to both ungrounded and grounded power system operation. Section 2 gives a brief summary of this literature survey and lists the important papers and books which were examined.

Jan 1, 1972

By Cawte D. C, Just G. D, Whitchurch K. D

The stringent marketing specifications included in coal contracts mean that coal producers must supply cleaner and more consistent coal than may have been formerly required. Geostatistics has the potential to aid in the accurate estimation of the washability characteristics of coal. A prediction method, the Kriged Service Variable Approach has been developed.A Computer Aided Drafting and Design system has proved useful in the development and application of the approach. The geostatistical approach has been tested against coal geological and borehole data and applications discussed.

Jan 1, 1987