Search Documents

By S. J. Boone, A. Poschmann, C. Pound, A. Pace

San Diego’s Stadium Conglomerate consists of poorly cemented cobbles, gravel, sand, silt and clay. Conventional laboratory and in-situ testing is not suitable for characterizing its engineering properties. Although the formation is often considered a “rock” its behavior is more readily modeled using soil mechanics. Static and seismic design of a tunnel for the Mission Valley East light rail extension required that the stress-strain characteristics of the ground be identified over a broad strain range. Geophysical methods and field plate load testing were used to develop a full non-linear stress-strain model of the expected ground behavior. Quantification of the coarse material distribution was also required for selection of tunneling methods and construction considerations.

Jan 1, 2001

By A. W. Khair

Laboratory studies indicate that the specimen size influences the compressive strength of coal significantly. In the past, the diameter/height ratio of coal and rock specimens with different geometry and its influence on failure characteristics was discussed (Khair, 1993; Khair, 1994; Khair and Xu, 1994). In the current attempt, tests are designed and carried out under uniaxial condition in the laboratory to investigate the influence of specimen size. Cubical specimens of coal with edge dimension ranging from 5 cm (2 in.) through 20 cm (8 in.) were prepared according to the standards and tested uniaxially. Results show that compressive strength of coal is dependent on specimen size until certain level and later the change in specimen size would not yield significant change in compressive strength. Cubical specimens were chosen for testing because they are not only in close resemblance to underground pillars, but they are also the most stable shape under loading. The failure characteristics of these specimens were analyzed and their applicability to pillar design aspects in coal mines is studied. A detailed analysis of the physical and mechanical properties of the tested coal seam is also presented.

Jan 1, 1996

By William J. Karwoski

To improve rock-burst control in deep vein mining, a field demonstration has been carried out by the Bureau of Mines to test a new rock-burst control concept--rock preconditioning in advance of mining. The procedure is to fracture the major rock-burst-prone zone during the development of each level before production mining. This allows initial mining to begin in a preconditioned zone and later mining from the level below to end in a prefractured or preconditioned pillar zone that is relatively burst-free. This full-scale field demonstration was carried out On the 7700 level of the Hecla Mining Co.'s Star-Morning mine. An expected burst-prone zone along the main vein between 7 and 10 crosscuts, some 250 feet long by 40 feet above and below the level, was preconditioned by blasting a fanlike ring of drilled holes from each crosscut. The drill holes, up to 100 feet long and 4 inches in diameter, were loaded with high explosives and shot. About 4,550 feet of drilling and 9,000 pounds of explosives were involved in the effort. Comparison of preshot and postshot data from monitoring instrumentation indicated that the blasting did fracture the rock in the planned zone and did result in an immediate stress decrease and softening of rock. The field data compared favorably with predicted results from a finite-element computer model simulation of the destressing. Based on observations made during mining and on the data from the Hecla rock-burst monitoring system, there is no doubt that this preconditioning in advance of mining demonstration resulted in much-improved rock-burst control during first-floor mining. It was also concluded that preconditioning the vein was more effective than preconditioning the wall rock.

Jan 1, 1979

By Spooner H. W

The paper describes the search for mineral deposits in an area of 4,500 sq. miles of south-west Tasmania. The area is one of difficult access and the problem of speedy movement and maintenance of field parties was solved by the use of helicopters. The programme has followed a systematic pattern of the aerial photography of the exploration area with the preparation of photQmosaics and topographical base sheets from these mosaics. Geological maps were initially prepared by photogeological interpretation and making use where possible of pre-existing information. The maps produced were later checked by ground traverses. Geophysical maps were obtained by the use of airborne magnetic, electromagnetic and radiometric methods. Geophysical and geological anomalies were checked on the ground by a campaign using ground geophysical equipment in the former case and geological and geochemical work in both instances. Audio Frequency Magnetic and Induced Polarization techniques were used in an area which was covered by several hundred feet of Tertiary sediments.The campaign has reached the stage of the drilling of specific targets.INTRODUCTIONThis paper describes the activities of Lyell-E.Z. Explorations (L.E.E.), an organization which was formed in 1956 by the Mt. Lyell Mining and Railway Co. Ltd. and the Electrolytic Zinc Co. of Australasia Ltd. to explore for mineral deposits in an area of approximately 4,500 sq. miles in southwest and southern Tasmania. To provide the necessary personnel and equipment for this project the exploration resources of both Companies were pooled and augmented and a headquarters was established in Queenstown. The work was directed by a Committee of four made up of officials from both Companies; a review of this structure has recently been presented by Hall (1959).

Jan 1, 1960

By M. K. Sichone

Anglo Platinum?s Waterval smelting complex based in South Africa operates the Anglo Converting Process (ACP) that produces SO2 offgas. This SO2 offgas is treated in a double-contact, double-absorption acid plant allowing for conversion efficiencies higher than 99.90 %. The catalytic converter used in the acid plant to convert the SO2 to SO3 is a 4-bed reactor loaded with a combination of cesium-promoted and conventional vanadium pentoxide catalysts. In June 2008 there was a shutdown, in which one of the main activities was to screen the catalyst. Before this shutdown, the operator would control the converter pass temperatures manually, via the SCADA, especially during plant start-ups after which some of the automatic temperature controllers were used. After the shutdown, the control philosophy was revisited and all temperature controllers were put on auto mode during plant start up. Furthermore the set points of the pass inlet temperatures were reduced to maximize conversion in the first two passes. The result has been a reduction of SO2 emissions, from a daily average of 50 ? 70 ppm to as low as 20 ppm for similar sulphur dioxide and oxygen concentrations. Further work has been done to maintain high bed temperatures in the third and fourth passes at low SO2 strengths by splitting the gas stream between pass 1 and 2 thus increasing the SO2 content in the gas to pass 2. This increases the temperature of the gas exiting the second pass, which results in higher temperatures in passes 3 and 4. Comparison of the converter performance prior to and after the changes is made. The benefits of partially bypassing the first pass to increase the SO2 content in the gas to the second pass are shown. Conclusions and scope for further work have been drawn from the comparisons.

Jan 1, 2009

By Rick Collins

Presentation Agenda 1.Sudbury Basin 2.Diamond Drilling 3.Planned Production 4.Safety 5.Timeline 6.Sustainable Development 7.Scope Elements 8.Progress 9.Delivery Approach 10.Owners and EPCM Roles 11.Contract Styles 12.Mine Systems & Technologies 13.Q & A

May 1, 2009

By J. E. Nesset, F. Rosenblum, J. A. Finch

"The self-heating of sulphides can be a major hazard in mining operations and concentrate handling, particularly during transportation and associated storage. Self-heating results from the oxidation of sulphide minerals and can vary from being insignificant to highly reactive and potentially hazardous to both humans and infrastructure. It is essential that there be a reliable test methodology that can measure and categorize a given sulphide material as to its self-heating potential. By their nature, sulphide ores and concentrates are complex and variable mineral mixtures making it difficult to predict their self-heating behaviour a-priori based on mineralogy or with a simple “snapshot” test. Furthermore, self-heating behaviour will depend on the state of oxidation of the sulphides as well as time, temperature and humidity. A review of available testing apparatuses and protocols that can be used to assess self-heating potential is presented. Each of these methodologies was examined in relation to its ability to measure and reliably predict the latent self-heating hazard of a sulphide material. Several of the methods were tested and compared to illustrate their strengths and weakness. The results indicated that a number of the test protocols may produce false negative indications of self-heating potential, constituting an obvious concern to the industry.INTRODUCTION Sulphides as well as other materials (coal, wood chips, hay, powdered milk, to name a few) that are stockpiled in an air atmosphere may undergo oxidation reactions which can result in the evolution of heat (Beever, 1984) (Hudak, 2002) (Blanchard, 2007). If the rate of heat generated exceeds the rate of heat dissipation, the stockpile temperature will rise, potentially leading to “hot spots” in the most reactive areas, and possibly even fires. The heat generation rate, the “self-heating” rate, depends on many factors such as the type and composition of material, particle size, moisture content, oxygen availability, ambient temperature and humidity, and of prime importance, the extend of prior oxidation, or more specifically, the presence of oxidation products. The desire of operators that mine, process or transport sulphide-bearing materials with a potential for self-heating is to have an accepted and reliable method for evaluating and quantifying the potential hazard of their material. The challenges are how to best measure the self-heating properties of given samples, and based on results, predict the behaviour of the bulk material over time and in-situ. Generally, when evaluating a given material one derives the self-heating characteristics of that sample at the time and under the conditions of testing, which will be referred to as a “snapshot test”. If that material is invariable, i.e. it will not change its response over time, then it may be considered to be a “predictive test”. However, if as a result of continuing oxidation or other changes, the material becomes more or less reactive with time, then a “snapshot test” is unreliable with respect to predictive ability."

Jan 1, 2014

By A. P. Whittlestone, J. D. Johnson, R. J. Pine, M. E. Rogers

standpoint. The effect on efficiency of collisions

Apr 1, 1995

By E. Jackson

This paper describes highlights of the Placer Dome MiniMole project - the development and testing of a robotic machine for mining narrow ore veins. A prototype hydraulically controlled robotic machine was built and tested. The machine provided a platform for testing numerous cutters in the field. Other cutters, e.g. undercutting devices, were tested in the lab. Extensive analyses were done on specific energies and cutter penetration. Three sets of quarry trials were done, then the machine was tested in an underground mine. Rock UCS values varied from 180 MPa to 230 MPa. The paper includes lessons learned and recommendations based on the project findings.

Jan 1, 2007

By P. J. Sylvester, D. H. C. Wilton, R. I. Wheeler, M. A. E. Huminicki, D. Evans-Lamswood

"Systematic characterization of the mineralogy of massive sulfide ore deposits can provide valuable insights into ore genesis and metallurgical processing that would not be apparent otherwise. We describe a method wherein (1) normative mineral abundances are calculated from whole-rock chemical assays using an algorithm, (2) the results are cast in block models, (3) the results are then verified with automated image analysis of a subset of samples prepared as grain mounts by backscattered electron imaging and X-ray mapping on a scanning electron microscope, and (4) those verified results are integrated with textural data determined by optical microscopy.The technique is applied to the magmatic Ni-Cu-Co sulfides of the Ovoid orebody, based on geochemical assays of 3175 whole-rock samples. Three principal ore zones are defined in the Ovoid. Type I ore occurs in the center of the deposit; it is magnetite-rich and pyrrhotite-poor with intermediate contents of pentlandite and chalcopyrite. Type II ore surrounds Type I ore and is pentlanditechalcopyrite- rich with intermediate contents of pyrrhotite and magnetite. Type III ore occurs at the base and along the outer periphery of the northern part of the orebody; it is pyrrhotite-rich and chalcopyrite- poor with an intermediate content of pentlandite, and a low-to-intermediate content of magnetite. La caractérisation systématique de la minéralogie des gîtes de sulfures massifs peut fournir des indications précieuses sur la genèse des minerais et le traitement métallurgique qui ne seraient pas disponibles par d’autres méthodes. Nous décrivons un procédé par lequel (1) un algorithme est utilisé pour calculer l’abondance de minéraux normatifs à partir d’analyses lithogéochimiques, (2) les résultats sont exprimés dans des blocs diagrammes, (3) les résultats sont par la suite validés par analyse d’image automatisée sur un microscope électronique à balayage en électrons rétrodiffusés et par cartographie en rayons X sur des échantillons constitués de grains montés en résine, et (4) les résultats de cette validation sont combinés aux données texturales obtenues par microscopie optique.Cette technique est appliquée aux sulfures magmatiques de Ni-Cu-Co du gisement Ovoïde, en utilisant les analyses géochimiques de 3175 échantillons de roche totale. L’Ovoïde comprend trois types de minerai. Le type I est situé au centre du gisement; il est riche en magnétite et pauvre en pyrrhotite avec des quantités intermédiaires de pentlandite et de chalcopyrite. Le minerai de type II entoure le minerai de type I et est riche en pentlandite et en chalcopyrite avec des quantités intermédiaires de pyrrhotite et de magnétite. Le minerai de type III se trouve à la base ainsi qu’à bordure externe de la partie nord du gisement; il est riche en pyrrhotite et pauvre en chalcopyrite, avec un contenu intermédiaire en pentlandite et une quantité faible à moyenne de magnétite."

Jan 1, 2012

By R. R. Lowery

This project was proposed to provide information on the hazards associated with arc melting of thorium. A general air-sampling analysis was made to determine the separation, concentration, and distribution of thorium daughter (decay) products throughout arc melting, machining, and forging processes of a thorium handling facility. The value of well coordinated health physics program is stressed in connection with potential health hazards and personnel protection. Building, equipment, and exhaust ventilation requirements for such a facility are discussed. Special handling methods are described for thorium. INTRODUCTION The Bureau of Mines at the Albany Metallurgy Research Center has been involved in handling the naturally radioactive metals, uranium and thorium, for several years. Cooperative work for the Atomic Energy Commission has been carried out with thorium metal, and as a result the concerned laboratories of the Center have accumulated experience on the hazards associated with this metal. This report details the radioactive hazards arising from the arc melting, machining, and forging of thorium.

Jan 1, 1962

By Steven R. Lowe

Construction of a pump station, consisting of an inlet chamber, wet well and pump chamber, required excavation to a depth of 9.7 m (32 ft) below ground surface and more than 7.6 m (25 ft) below the ground water table in a rural, but rapidly developing part of southern New Jersey. Private houses are located [ ] within a few hundred feet of the pump station that use shallow wells for water supply. The pump station design anticipated support of the entire pump station on shallow foundations bearing directly on the underlying natural soils. However, during construction, uncontrolled ground water flow caused ground loss and damage to the bearing qualities of foundation soils. As a result, remedial repairs were required including support of the pump station on drilled pile foundations and releveling of the pump chamber that had settled. This case study is an example of where a poor understanding of the significance of upward flowing ground water had a major impact on the cost of construction. Anticipated subsurface conditions The pump station layout is shown in Fig. 1 with the locations of two borings made prior to construction superimposed. One of the borings was located within the footprint of the deep wet well excavation. Generally, this is not advisable where a deep excavation is required below the ground water table. This is because there is a history of projects where ground water seepage, or pressure, has broken out into an excavation through an ungrouted borehole and compromised the integrity of foundation soils. Logs of the borings did not indicate that the borings [ ] were grouted upon completion.

Jan 1, 2011

By B. Anameric

The pig iron nugget process is gaining in importance as an alternative to the traditional blast furnace. Throughout the process, self-reducing?fluxing dried greenballs composed of iron ore concentrate, reducing-carburizing agent (coal), flux (limestone) and binder (bentonite) are heat-treated. During the heat treatment, dried greenballs are first transformed into direct reduced iron (DRI), then to transition direct reduced iron (TDRI) and finally to pig iron nuggets. The furnace temperature and/or residence time and the corresponding levels of carburization, reduction and metallization dictate these transformations. This study involved the determination of threshold furnace temperatures and residence times for completion of all of the transformation reactions and pig iron nugget production. The experiments involved the heat treatment of self-reducing?fluxing dried greenballs at various furnace temperatures and residence times. The products of these heat treatments were identified by utilizing optical microscopy, apparent density and microhardness measurements.

Jan 1, 2007

By B Murphy

Traditionally comminution optimisation has been focused on energy minimisation, whereas flotation optimisation has been focused on recovery improvement. One of the largest, if not the largest, operating cost over the life of a flotation circuit is electrical energy. With increasing pressure on operators to lower production costs and the cost of energy increasing, reducing the energy consumption of the flotation circuit can be beneficial to site economics. This paper reviews the use of energy by mechanically agitated flotation machines and discusses the measurement and benchmarking of energy consumption in modern flotation concentrators. Opportunities for improving flotation energy efficiency are also identified.CITATION:Murphy, B, 2013. Flotation energy consumption and opportunities for improvement, in Proceedings MetPlant 2013 , pp 399-412 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

With the change in legislation under the Resource Management Act 1991 (RMA), the responsibility for administering the effects of blasting on the environment, has transferred from an essentially central government system to local bodies. This naturally will allow for a variety of compliance levels and control procedures which will depend on the particular local body and rather ad hoc arrangements. It is anticipated that the existing NZ Standard on blast vibration levels will soon be replaced by the Australian Standard. These changes raise the question as to what should be used as suitable compliance levels to prevent damage to structures. The paper will address the measurement, control levels and the appropriateness of current standards in relation to the overall legal framework of the RMA.

Jan 1, 1996

By R. Heuberger

South Africa?s Mining Industry operates in an uncertain world. The industry is buffeted by problems regarding retrenchments, unemployment, low productivity, rising costs, volatile exchange rates, commodity prices and government regulations. With these uncertainties facing the decision makers, what does applied technology offer the industry?s management? Modelling languages with risk analysis have been available for decades, but in the past their use has been very expensive, requiring large mainframe computers and lots of computer time. Today, PCs and laptops have incredible power, which makes interactive risk analysis affordable and viable for all enterprises, whether small or large. ?What is risk analysis? ?What is Monte Carlo simulation? ?What kinds of computer models need to be created to use risk analysis and Monte Carlo simulation effectively? This paper addresses these questions and illustrates, with a practical example in the mining industry, how risk analysis techniques can be used to support decisions in the climate of uncertainty.

Jan 1, 2005

By S. M. M. Safvi, A. Jowett

Small-scale continuous flotation tests are described in which the influence of 1) pulp density and 2) feed rate on the rate of flotation are investigated. The results provide further evidence of first-order kinetics for flotation and indicate that tests at different feed rates provide a particularly simple method of determining rate constants. Flotation kinetics are discussed in general terms. Over a period of many years numerous research workers have studied the rate of recovery of valuable materials from flotation pulps with a view to deter-mining the mechanism of the froth flotation process. Froth flo ation is fundamentally a collision process involviug at some stage collision and then mutual attachment between air bubbles and mineral particles. It is possible to draw analogies therefore between the flotation process involving mainly macroscopic particles and the ordinary processes of chemical reaction kinetics involving collisions between atoms, molecules and ions. By adopting this analogy we may postulate a general equation representing the kinetics of the flotation process: -dC/dt =K.CC ,Aa (1) The rate constant, K, will be a complex function involving reagent concentrations, particle and bubble sizes, induction times and no doubt flotation cell design. However, these are factors which can be kept constant in any series of experiments, permitting investigation of the exponents a and c, which determine the order of the reaction occurring in flotation. The various research investigations carried out so far have all aimed at evaluating a and c and in the majority of cases only since the concentration of air has usually been kept constant in a series of tests, so that a relationship of the following type has been investigated: -dC/dt = K1 Cc (2) The techniques of both batch testing and continuous testing have been used to investigate this relationship. The technique of continuous testing, in which steady-state conditions are established, permits direct investigation of the above equation. In the case of batch testing, C is decreasing continuously

Jan 1, 1961

By L. Bruce McDonald

This Federal Bureau of Mines publication is a statistical analysis of all surface and underground coal mine fires reported in the United States from 1950 to 1977. Accounts of selected nonreportable fires and opinion data gathered via interviews with mine safety directors were separately analyzed. Both reported and nonreportable fires were analyzed by time trends, State, ignition source, burning substance, location in mine, equipment, detection, duration, injuries, fatalities, and successful extinguishing agents. It was found that the majority of all mine fires were electrical in origin. The equipment most frequently involved in underground fires was conveyor belts, and in surface fires, it was crushers and/or breakers. Underground fires occurred most often near the working face. Water and hand-portable extinguishers were the most common methods of extinguishment.

Jan 1, 1980

By John Folinsbee, Brian Danyliw, Tony Y. Chong

"Control of fugitive dust has become increasingly important in the mining industry both from a health and safety and environmental standpoint. Mining operations in particular have required improved fugitive dust control due to recent lowering of the allowable airborne silica concentration to which workers can be exposed. Experience has now proven that the implementation of a surfactant based chemical dust suppression system can enhance existing mechanical dust control methods resulting in much more efficient control of fugitive dust.The Porcupine Joint Venture (Dome Mine) utilizes dry secondary crushing and screening that makes it particularly prone to fugitive dust emissions. A variety of potential dust control systems were evaluated and this led to the installation of a surfactant based water spray system to augment the existing mechanical dust collection systems.A great deal was learned through the implementation of this system. This paper describes the entire process, from testing, system design and installation, through optimization and standardization of operation. In addition a variety of problems were identified, and innovative solutions were provided. Also, the metallurgical impacts on down stream processing are highlighted. Finally, a full discussion of overall results including a discussion of the relationship between silica and total dust concentrations is included."

Jan 1, 2005

By Rimas Pakalnis, Tom Brady, Lewis Martin

A major focus of ground control research presently being conducted by the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is to incorporate weak rock masses (such as are associated with operations in the Carlin Trend in Nevada) into existing design relationships. The original database that led to most of the empirical design relationships presently employed in hard-rock mining was derived from fair-to-good-quality rock. In this study, the relationship between weak rock quality and opening design (nonentry/entry methods) is being investigated. The common factor in all mines is a weak back or wall. This work attempts to provide tools that will enable a mine operator to make economic decisions that will also ensure a safe working environment.