Search Documents

By H. Fukuyama

The wetting behavior of single crystalline MgO by fayalite-type slag melts has been studied by the sessile drop technique incorporated with high temperature X-ray radiography. The experiments were performed under oxygen partial pressures of 10-6 and 10-4 Pa at 1473 K. Mass ratios of iron to silica, Fe/Si~, in the slag employed were 1.4 and 2.0. To investigate the interfacial reaction, experiments using high density MgO crucibles were also conducted. The reactions at the interfaces were examined by Electron Probe Microanalysis. The contact angles between the slag melts and the MgO substrates were found to be relatively low, ranging from 30 to 10 degrees. The surface tension of the slag was 0.4 N/m for a slag of Fe/Si02 = 2.0. Two phases, magnesiowiistite and olivine, were observed at the interface. Interdiffusivity in magnesiowiistite solid solution was determined as a function of iron oxide content. Phase relations between magnesiowilstite and olivine, and the growth rates of both phases, are also discussed

Jan 1, 1996

By S. K. Utimurd, D. C. R. Espinosa, J. A. S. Tenório

"Waste Electrical and Electronic Equipment (WEEE) has become an environmental issue due to technological advance and waste plastic is one of the main polluters. The excessive discard of these plastics result in a difficult to dispose it to landfill and need further separation with technique in order to produce high added value plastics. There are many kinds of plastics in extensive use at the present time and the co=on are the acrylonitrile-butadiene-styrene (ABS) and high impact polystyrene (HIPS) used in the production of electric appliances. These plastics are difficult to separate because they have similar densities. Flotation of plastics is one possible separation technique and using selective wetting agents. The separation may be possible given close control at particle size and the concentration of the reagent. The process was able to produce a concentrate of HIPS with at least of 93% purity and a concentrate of ABS with 99% purity.IntroductionThe current situation of municipal solid waste (MSW) management especially in emerging economies like Brazil, the growing population and economic activity will result in a significant increase in the generation of waste in the coming decades. It is worthwhile to review and update the sources, amounts and recovery technologies of specific materials from waste, particularly from municipal solid waste (MSW).The growing impact of the current waste management practices stresses the need for a change in how waste is handled. The 2012 survey and the Brazilian Association of Public Cleaning and Special Waste Disposal Companies (ABRELPE) reports the generation of 62 Mt urban MSW in that year, which is an increase of 13% compared to 2011. It has been reported that in Brazil about 90.17% of the generated MSW is currently collected, which indicates an increase in the coverage of collection services compared to 2011 [ l]."

Jan 1, 2014

By Hassan Saalman, Mahmoud Mahmoud, Omneya El Hussaini

The Ferruginous sandstone ore was obtained from Ramlet Hemeyir area, Southwestern Sinai, Egypt, was found to contain 10% rare earth elements (REE). A representative sample has been subjected to sulfuric acid agitation leaching. About 93% of the REE content was released by mixing the ground sample to -100 mesh with concentrated H2SO4 at solid/liquid (S/L) ratio of 1/2 for 5h at a temperature ranged from 250 to 300o C. The REE was precipitated from the prepared sulfate leach liquor of pH 1.0 by adding 35% oxalic acid at 25o C. The precipitation yielded 98% REE. For selective separation of yttrium, the rare earth cake was leached with 31.5% nitric acid. Next, the aqueous solution was contacted with di-(2-ethylhexyl) phosphoric acid (D2EHPA) where 98% yttrium extraction was achieved. Stripping was done with hot H2O (80o C). Finally, a precipitation with oxalic acid was done followed by ignition at 950o C. A yield of 95% yttrium oxide was produced.

Jan 1, 2014

By C. B. Catanach

The development and in place leaching of a chalcocite ore body at Mountain City, Nevada is described. Block caving was used to induce permeability while ore removed during development was leached in heaps on the surface. Copper was recovered by precipitation on iron. Excess ground water which seeped into the mine was pumped into a deep disposal well. A parallel system was used to purify water by lime neutralization. Copper extraction was at an annualized rate of 11% during the first six full months of underground leaching and totalled approximately 30% during six months of heap leaching. Leach solution flow and distribution had a major effect on extraction rate. Enrichment of leach solutions with ferric sulfate did not produce conclusive results until analyzed with the aid of a leaching model.

Jan 1, 1976

By Gernot Schenker

With the shut-down in the mid-1970s of the last shaft furnaces in the Harz Smelter Plant the long tradition of the Primary Lead Smelter in Oker came to an end. A continuation of the concern was nevertheless possible as a result of the timely commencement with the development and construction of lead production from secondary raw materials. Then as today, the most essential secondary raw material is lead accumulator scrap with over 80 % of the raw material pallet. Already in the 1960?s a method of reclamation lead battery scrap was developed and successfully carr.ied out by Preussag. In 1983 this process was fundamentally modified, also for environmental protection reasons within the framework of a rehabilitation programme of the existing plant. Today Metaleurop's HarzMetall GmbH in Oker is equipped with a modern secondary lead smelter which includes all environmental protection installations required by law. Besides processing battery scrap, the. smelter is in a position to process a ?multitude of other lead bearing residues in an economically useful way, whose waste disposal would otherwise be impossible due to the ever-increasing environmental protection laws or only be achieved at great expense.

Jan 1, 1990

By Shengli Wu, Feng Chang, Hua Lu, Jianliang Zhang

Kinetic studies of the blast furnace dust (BFD) reduction process have been carried out under non-isothermal conditions. BFD pellets were made with bentonite as the binder. A Comprehensive Thermal Analyzer (TG-DSC) was used to determine the mass loss of pellets, which were heated at three heating rates of 10, 20, 30 K/min up to 1493 K. Furthermore, the metallization rate and mineral composition of BFD pellets heated to several different temperatures were analyzed by chemical analysis and X-ray diffraction (XRD). It was found that, with its inherent carbon resources as the reducing agent, the metallization rate of BFD pellets could reach 88% at most. The reduction and weight loss process of iron oxides mainly happens above 1273 K. In addition, from application of the Coats-Redfern equation the apparent activation energy of the reduction from wustite to Fe was 443 kJ/mol and the mechanism was interface reaction R..

Mar 1, 2017

By Upali Siriwardane, Tushar V. Kudale, Naidu V. Seetala

"Cellulose acetate (CA) membranes with 25% triethyl citrate (TEC) as plasticizer were prepared with varying thickness for CO2 gas separation from water-gas-shift (WGS) reaction products. The AFM analysis of the CA membrane showed that the uniform coating had fewer and smaller pores as the film thickness increased, and corroborated by gas permeability studies. The CO2 permeability has decreased faster than CO permeability with the CA/TEC membrane thickness, and findings support that the CA membrane could be used to entrap CO2. Several CA/TEC membranes were also staked to increase the separation efficiency. Positron Annihilation Lifetime Spectroscopy (PALS) was used to estimate the nano-porosity (pore size and concentration) changes of CA/TEC films. PALS results show a decrease in pore size with increasing CA-TEC concentration in acetone, while the pore concentration increases. The PALS results are correlated with the CO2/CO permeability variations as the CA-TEC concentration change.IntroductionHydrogen is one of the main energy sources available for the future advancement of clean fuel technologies especially for fuel cells. Generation of hydrogen and CO2 from Water Gas Shift (WGS) reaction mixtures of CO and H2O is of interest to many researchers since it allows a large scale production of hydrogen [1, 2]. Once hydrogen is produced using the WGS reaction, the output products contain mixture of CO, CO2, H2, and water vapor. Metallic membranes have been used as hydrogen separation membranes [3-6]. As H2 is separated from the mixture using the metal membranes, we need to separate CO2, and find ways of sequestration of CO2 to avoid environmental problems by greenhouse gasses. Polymeric Membranes have been used for CO2 separation [7]. Plasticizer can control the micro-structural properties such as pore size and concentration of polymer membranes [8], which influence the size/molecular weight dependent diffusion rates of the gas molecules. We have used cellulose acetate with triethyl citrate as plasticizer to separate CO2 from the WGS reaction products. Positron annihilation lifetime spectroscopy (PALS) is very sensitive and able to identify different kinds of defects and their agglomerates such as vacancies, vacancy loops, and voids [9, 10]. PALS has been successful in determining the free volume in polymers that influence the properties of the polymers [11, 12]. Microscopic properties of the free volume obtained from PALS have been correlated to macroscopic properties [13, 14]. We used PALS to study the nanoporosity (pore size and concentration) and fractional free volume changes of CA/TEC films, and used to understand the variations observed in the CO2/CO permeability as the CA-TEC concentration in the membranes change."

Jan 1, 2014

By Anna Franzkowiak, Dean Gregurek, Alfred Spanring, Angelika Ressler

In order to determine the most suitable refractory products and improve the lining lifetime for the diverse furnaces used in the nonferrous metal industry, corrosion tests are performed at RHI’s Technology Center. The practical facilities include the cup test, induction furnace, rotary kiln, and drip slag test described in this paper, which enable a comprehensive understanding of the chemo-thermal brick wear on a pilot scale. The corrosion trials are performed with actual slags generated during operations at a customer’s plant. To determine the highest influencing wear parameter, every single test is combined with a detailed mineralogical investigation and thermochemical calculations performed using FactSage. Based on the results, tailored refractory solutions for the nonferrous metal industry can be provided in combination with trials conducted at the customer’s site.

Jan 1, 2014

By D. M. Jones

Dust generation data have been obtained from 19 industrial Outokumpu flash furnaces. Statistical analyses of the data have been carried out and the most significant factors affecting dust generation evaluated. The results indicate that dust production may most effectively be minimized by: 1) Minimizing the distance between the molten slag and the furnace roof 2) Optimizing burner design and combustion parameters.

Jan 1, 1996

By Jr. Langhans, J. S. McPartland

"The presence of zinc in cyanide solutions is generally thought to not have an adverse effect on precious metal recovery or recovery rate by heap leach processing. However, analytical interferences of zinc in solution can cause problems in accurately determining and controlling cyanide concentration in the leach solution, leading to increased cyanide consumption. Analytical methods and the chemistry of cyanide in the presence of zinc are reviewed. The effects of solution pH and zinc concentration on the free cyanide determination were evaluated in detail. Use of the standard silver nitrate titration and a modified titration method for controlling cyanide concentration during heap leaching were investigated experimentally. The practical implications of cyanide heap leaching in the presence of cyanide soluble zinc minerals are discussed.IntroductionThe presence of zinc in precious metal cyanidation circuits is not uncommon. Zinc can be introduced into cyanide leach solutions through dissolution of various zinc minerals1>, or through the use of a Merrill Crowe (zinc precipitation) circuit. Zinc minerals typically occur infrequently and in low concentration in gold ores, but are more abundant in silver ores. Merrill Crowe systems are most commonly employed for recovery of precious metals from solution for relatively high silver ores. It is desirable to control the amount of dissolved zinc in a cyanidation circuit for several reasons. Excessive zinc build-up in cyanide leach solution can, under certain circumstances, inhibit precious metal dissolution and adversely affect solution recovery systems. Additionally, high zinc concentrations can lead to excessive in-process cyanide inventories and potentially, to higher cyanide consumption"

Jan 1, 1999

By Benjamin P. Hay

Complexation of a metal ion to a ligand often results in structural changes that introduce steric strain within the ligand. A design criterior:1 for ligands that will complex metal ions more strongly is to choose Iigar:1d architecture, that minimizes this strain. This paper describes how molecular mechanics models can be used to define the degree of ligand binding site organization in terms of' ,strain energies associated with conformational reorganization and distortion of the binding conformer. This approach yields a method to predict how modifications to ligand structure will affect metal binding affinity.

Jan 1, 1999

By Alexander Burns

Electrolytic salt splitting is a technology where acid and/or base is regenerated from a neutral salt using membrane electrolysis. Recent advances in the understanding of brine treatment, membrane stability, and cell design have made electrolytic salt splitting feasible on certain hydrometallurgical solutions. Meanwhile, environmental regulations have made the bulk disposal of salt solutions more difficult. In this paper, sodium sulfate salt splitting is examined from a cost perspective, compared to purchasing the reagents directly. Relative costs are estimated for several regions based on published electricity and reagent prices. The results show that salt splitting is economically favourable in some regions, and can be made more favourable by applying modifications to the traditional three-compartment desig

By P. C. Chaubal

The overall kinetics of oxidation of single partic1es of chalcopyrite have been studied for temperatures up to 1273 K. The experiments were conducted in a stationary bed reactor using a non-isothermal technique. Any mass and heat transfer effects on the kinetics of oxidation were eliminated by using a high-enough gas flowrate. Up to temperatures of 873 K, pore-bl1ocking kinetics were applicable, whereas above 873 K, power-law kinetics gave a satisfactory fit of the data. The activation energy was 215 kJ/mol below 754 Kand 23.7 kJ/mol above 1,060 K. Predominance area diagrams were constructed at various temperatures and used in conjunction with X-ray analyses of partially oxidized samples to determine the intermediate phases formed during the reaction. The analysi1s also provides a justification for the kinetic models used. The results indicate that the reaction rate is first order with respect to oxygen concentration and inversely proportional to the square of the particle size throughout the ranges of temperature studied.

Jan 1, 1985

By Francisco M. S. Garrido, Fabiano A. C. M. Passos, Carla N. Barbato, Karoline K. Ferreira, Danielle C. Castro, Adriana A. S. Felix, Luiz C. Bertolino, Fernanda A. N. G. Silva, Karla M. A. Simões

Cancrinite and sodalite are characterized by high capacity of adsorption due to its porous structure. The aim of this work was to use kaolin from Borborema-Seridó/Brazil as a source of aluminium and silicon to hydrothermal synthesis of sodalite and cancrinite and to evaluate the best conditions to the formation of these phases. Therefore, kaolin was heated at 700 and 900 °C for 2 h in order to transform kaolinite in metakaolin. Thereafter, experiments with the calcined kaolin’s were carried out between 150 and 230 °C for 30–270 min on a stainless steel pressure vessel using NaOH, Na2CO3 and H2O. The samples were characterized by X-ray diffraction, nuclear magnetic resonance, scanning electronic microscopy, thermogravimetry, and Zeta potential. The most pure sodalite phase was obtained at 230 °C, with the kaolin/NaOH ratio of 1:1, low concentration of Na2CO3 and smaller time of synthesis (30 min). On the other hand, for the synthesis of cancrinite phase at 230 °C, it was necessary to use kaolin heated at 900 °C, a longer time of synthesis (270 min) and a higher concentration of Na2CO3.

Mar 1, 2017

By Guo Chen, Xuefeng Liao, Tu Hu, Shengzhou Zhang, Hongying Xia, Jinhui Peng, Libo Zhang

Pine nut shell is as raw material for preparation of high surface area activated carbon (HSAAC) by microwave induced KOH activation. The effects of microwave power, activation duration and KOH/C mass rate (R) on the iodine adsorption capability and activated carbon yield were investigated. Additionally the surface characteristics of HSAAC were characterized by nitrogen adsorption isotherms and SEM. The operating variables were optimized utilizing the response surface methodology and were identified microwave power 738W, activation duration 17 min, and R 4, corresponding to a yield of 46.28 % and an iodine number of 2154 mg/g. The key pore structure parameters of HSAAC such as the Brunauer–Emmett–Teller (BET) surface area and total pore volume were estimated to be 3819 m2/g and 2.09 mL/g, respectively. The findings strongly support the feasibility of microwave heating for preparation of HSAAC from spent pine nut shell by microwave induced KOH activation.

Jan 1, 2016

By P. Peczak

A Monte Carlo simulation technique has been used to study dynamic recrystallization in polycrystals. A continuum microstructure of the polycrystal is modeled employing a discrete lattice. The response of the material to hot deformation is simulated by adding stored energy and recrystallization nuclei continuously with time. The experimentally observed nonuniform character of deformation substructures is modeled by employing a phenomenological expression for inhomogeneous distribution of the stored energy. All simulations were performed on HP-Apollo 9000 Series 700 workstations. A program written in FORTRAN with use of PHIGS graphics library calls was used to interactively monitor the current state of the matrix and all relevant parameters: deformation stress, average grain size and effective nucleation rate. Visual analysis of the simulated microstructure allows a better understanding of the data developed by averaging over a number of very long Monte Carlo runs. Since the essential features of dynamic recrystallization are accurately reproduced by the model, it is used to discuss the role of the controlling mechanisms of the dynamic recrystallization in real polycrystal.

Jan 1, 1993

By Reza Kamali, Mohsen Bashiri, Hadi Fanisalek

"Half of the input energy to aluminum reduction cell will be lost as waste heat which could be studied for possible recovery. Since price of energy is increasing and the main production cost in primary aluminum industry is energy, so waste heat recovery consideration will be interesting. One of the possible choices for recovering is from aluminum exhaust gases that needs minimum modifications for reduction cell and has no influence on cell heat balance which is vital for the operation. By using heat exchangers with in-line and staggered tube arrangements which placed before fume treatment plant (FTP) we will be able to recover enough amount of heat. The main challenging problem which is necessary to overcome will be the heat exchanger material and its design because of corrosive and dusty exhaust gases from potroom. In this paper, a desalination system with six effects of evaporator is proposed for producing distilled water by using recovered heat from hot exhaust gases. The calculated amount of produced distilled water is around 27,000 / in this specific suggested desalination plant. The suggested desalination plant is based on Hormozgan Aluminum Company data (Hormozal) in Bandar Abbas, Iran which is constructed by the Persian Gulf.IntroductionWaste heat losses arise both from equipment inefficiencies and from thermodynamic limitations on processes. The exact quantity of industrial waste heat is poorly quantified, but various studies have estimated that as much as 20 to 50% of industrial energy consumption is ultimately discharged as waste heat [1]. In order to achieve a final decision for establishing the waste heat recovery plant in any type of industry, a strong feasibility study is mandatory. Also, we need to remember that the possible amounts of energy and suggested process plant for recovery have to be investigated before starting any feasibility study. This kind of study which is important to be finished before moving to feasibility step is mainly a theoretical study, and was done for the Hormozgan Aluminum Company (Hormozal). In addition to the exhaust gases from the potroom, the exhaust gases from anode baking plant appear to have a better potential for waste heat recovery compared to potroom exhaust gases. The average temperature of exhaust gases from anode baking kiln is 120°C higher than the exhaust gases temperature in the potroom. This needs further investigation in a different study, because this study is just focusing on potroom exhaust gases."

Jan 1, 2011

By Dandan Jian, Christian Karcher

Information of liquid steel flow patterns inside the mold may be obtained from the velocity at the free surface (meniscus). This meniscus flow may be measured using the contactless electromagnetic technique termed Lorentz force velocimetry (LFV). It is based on the measurement of Lorentz forces acting on a magnet system when an electrically conducting metal melt interacts with the field lines stretched by the magnet system. Force sensor and the magnet system form a so-called Lorentz force flowmeter. In this paper we present a series of model experiments that demonstrate the feasibility of using two identical flowmeters that are arranged in a certain distance one behind the other. In this case, surface velocity may be determined by just cross-correlating the two force signals recorded by the two sensors. This technique is called time-of-flight LFV. A special prototype of a respective measuring device, called meniscus velocity sensor (MVS), has been developed to measure local free-surface velocity. In the present paper we describe experimental results of respective measurements in the model test stand LiMeSCo (liquid metal surface velocity correlation). To check the potential of the time-of-flight technique, in a first step we measure surface velocities during solid-body rotation of metallic substances. We observe that small modulations in the signals that are due to the natural unevenness of the solid body can be used to determine surface velocities. In a second step we apply the time-of-flight technique to liquid metal free-surface flow. Here we use the low-melting eutectic alloy GaInSn as a test melt. In this case we observe that the cross-correlations between the signals are much rarer and much weaker than in the solid-body experiments. We conclude that the presence of the localized magnetic fields, produced by the permanent magnets of the flowmeter, give rise to intense deformation of the free surface and the creation of surface waves. The field acts as a magnetic obstacle. We observe that the flow velocity is decreased right underneath the magnetic field and is accelerated in the side regions. This magnetic obstacle effect may restrict the determination of the local surface velocity in application.

Jan 1, 2012

By R. Hammen

Processes are needed to rapidly and cost-effectively produce highly pure lithium salts for the rechargeable battery sector. Lithium purification is a chemical engineering challenge, due to the low concentration of lithium compared to sodium, potassium, magnesium, calcium, and transition metal ions commonly occurring in lithium brine resources. We describe a Solid Phase Extraction (SPE) process that rejects sodium and potassium, while binding lithium and other higher valent ions. Lithium is then harvested by selective displacement from the SPE column. The rapid equilibration kinetics of SPE composites enables these ion separations to occur in a small SPE column and in one column stage. The chemical parameters of the process are described.

By Chan. C. L., Zehr. R., M. M. Chen, J. Mazumder

"Two three-dimensional models of a surface tension gradient driven flow during laser surface heating are developed. The first model is based on a perturbation solution. The basic solution corresponds to the stationary axisynwnetric case and perturbation is based on a small scanning velocity. The advantage of seeking a perturbation solution, as it turns out, is that the three-dimensional flow is modeled by two sets of two-dimensional equations which are presumably much more tractable than the original three-dimensional equations. Numerical solutions are obtained and discussed. The second model is a full three-dimensional numerical solution of the Navier-Stokes equations, using a point-by-point partially vectorized iteration scheme. Surface shape is also determined in a self-consistent manner. The effect of the presence of convection on pool geometry, cooling rate and solute redistribution is presented and discussed.IntroductionThe existence of fluid flow and convection and their effects were first reported in the fifties (1,2). The role of convection in controlling pool geometry such as pool shape, undercut and ripples, and defects such as variable penetration, porosity and lack of fusion and weld properties such as weld homogeneity and bead formation is studied by a number of researchers and is reviewed by the authors in a recent paper (3).Recently, surface tension gradient driven flow has been identified as one of the forces responsible for convection within the molten pool (4,5). It is postulated that surface tension gradient driven flow is responsible for the surface ripple formation in the weld pool (6-8). Oreper, et al. (9) developed a two-dimensional convection model. Buoyancy, electromagnetic and surface tension gradient forces were considered. The formulation was based on a specified pool profile. It was found that the surface tension gradient is the dominant force in most cases. However, the solid-liquid interface is not known a priori. In fact, the solid-liquid interface, i.e. the pool shape, is a piece of information that the model should be able to predict. A two-dimensional transient self-consistent (i.e. the solid-liquid interface is solved as part of the solution] model for laser surface melted pool was first developed by Chan, Mazumder, and Chen (3)). This model predicted a non-uniform cooling rate, hence non-uniform microstructure. Depending on the Prandtl number (i.e. material) and surface tension number, the shape of the molten region as well as the cooling rate changes. It was also predicted that the recirculating velocity is of one or two order of magnitude higher than that of the scanning velocity. This model provides the detail of the flow field and heat transfer on a plane perpendicular to the scanning direction. However, the front-to-back motion and its effect on heat transfer also play important roles in the physical process, especially for the fact that the recirculating velocity is so much higher than the scanning velocity. Such a motion cannot be obtained from two-dimensional models."

Jan 1, 1986