Search Documents

By C. A. Natalie

Prediction of average residence times for different particle size intervals during sulfide roasting was investigated. Calculations were done to predict average residence times using a model which employs empirical correlations for elutriation constants. Experimental average residence times were determined using a continuous., six inch diameter,. fluid bed roaster and compared with calculated residence time values. Comparison of calculated and experimental data showed that geometry effects may have .been significant when attempting to apply elutriation data to this roaster.

Jan 1, 1985

By G.A Subagyo

The condition of slag in a pyrometallurgical reactor is vital to ensuring control of the process. A new technique based on multivariate image analysis (MIA) of digital images has been developed to provide an online measurement of important slag characteristics, such as the presence of exposed metal, the presence of solid phases, and temperature. This paper shall describe the technique and provide some results from analysis using industrial plant data.

Jan 1, 2003

By Jack S. McPartland

Historically, research on thiosulfate leaching of precious metals ores has been focused on processing of difficult to treat ores. Thiosulfate leaching of ores and concentrates containing sulfide minerals, copper, manganese and preg-robbing carbon constituents has been evaluated. Cyanide leaching is generally considered an efficient, environmentally acceptable means for processing of non-refractory precious metal ores, Consequently, commercial processing of finely disseminated, oxidized precious metal ores is normally accomplished using alkaline cyanide leaching. Recent changes in regulatory climate have, however, called into question the acceptability of cyanide leaching in a number of locations worldwide. In some cases where the use of cyanide is being questioned, thiosulfate leaching may provide an acceptable alternative. Developments in thiosulfate leaching of precious metal ores are reviewed in this paper.

Jan 1, 1999

By Jiang Feng, Zhang Libo, Peng Jinhui, Guo Zhanyong, Ju Shaohua, Lei Ting

The basics of microwave drying process of CuCl residue were studied by comparing the dielectric property of the residue with different moisture contents. The dielectric properties were measured by microwave cavity perturbation method. The dielectric constant and dielectric loss factor of the CuCl residue have a linear correlation with the moisture content. With this relationship, we can realize on-line measurement of moisture content of the CuCl residue by dielectric properties. The microwave drying experiments with different thicknesses (1-5cm) of CuCl residue were carried out, and the heating curve of the materials under different microwave powers (250-450W) was made. From these parameters, an optimized operation parameter of microwave roasting technology, the thickness of CuCl residue filter cake to be microwave roasted should be 2cm , was deduced.

Jan 1, 2015

By Florian Kongoli

The production of a homogeneous self-fluxing sinter is an important step in iron making processes. A good sinler should have good permeability and reducibility and has to keep those characteristics for a certain time. An early melt down of the sinter in the blast furnace, where its solid state reduction is essential, would cause many problems such as low permeability and reductibility. Nevertheless, the important factors that influence these characteristics, such as the chemistry of the sinter and the fluxing effect during sintering and sinter reduction conditions have not yet been clarified, In today's new reality where many new minor components such as Al2O3 and MgO enter to the sinter through raw materials, the quantification of the fluxing effects during sintering becomes even more important. In this work, the liquidus surface and phase relations of the sinter primary melts in the CaO-FeO-Fe203-Si02 system at sintering conditions have been quantified. The fluxing effect of oxygen potential, Al2O3 and MgO has also been quantified by the means of some practical diagrams that can directly help the optimization of the sintering processes.

Jan 1, 2003

By Sergio N. Monteiro

Lignocellulosic fibers obtained from plants like cotton, flax, hemp, sisal, jute and many others are natural materials used, since long time, in basic items such as textile, baskets, roofing and carpets. These traditional natural fibers as well as some new ones are nowadays replacing synthetic fibers as composite reinforcement owing to environmental advantages. The heterogeneous characteristic of lignocellulosic fibers is, however, a limitation for application in composites. The buriti fiber, extracted from a tropical plant tree, is recently being investigated as a possible reinforcement for polymeric matrix composites but no complete information exists regarding its mechanical behavior. The objective of this work was then to carry out a statistical analysis on the mechanical properties? uniformity of buriti fibers. By precise dimensional measurements in association with tensile tests, it was found that the mechanical properties depend on the range of the fibers? dimension.

Jan 1, 2009

By C. A. Summers

The U.S. Bureau of Mines applied process mineralogy to investigate a lead and zinc deposit located near Story Creek, Colville Mining District, Alaska. Mineralization is hosted by the Kayak Shale in veins, veinlets, and breccia. Sphalerite and galena, with supergene anglesite, occur in symmetrical quartz veins and between breccia clasts. The study sample analyzed 2.11 percent Pb, 5.37 percent Zn, 0.014 percent Cu, and 1.2 oz/ton Ag. Analyses of crushed products showed that 33 percent of the sample weight, and more than 50 percent of the Pb and 65 percent of the Zn, are in the minus 850 um fraction. Liberated grains of sphalerite and galena were found in crushed products finer than 300 um. Beneficiation tests indicate the material is amenable to processing by traditional gravity and flotation techniques.

Jan 1, 1991

By B. C. Blakey

The economic feasibility of the sulphuric acid pressure leaching route for the extraction of nickel and cobalt values from limonitic ores is highly dependent upon the behavior of aqueous aluminium. This is primarily due to its precipitation as hydronium alunite ((H30)A13(S04)2(OH)6), which is one of the major scale-forming compounds found in autoclaves used for pressure leaching. As a result of renewed interest in the pressure leaching process, an investigation of the aqueous-solid eqilibria in the aluminium-sulphate-water system under acidic (< pH l), high temperature (230 to 270°C) conditions has been conducted. Pure hydronium alunite was synthesized in an autoclave by leaching boehmite (A100H) at elevated temperatures in sulphuric acid solutions initially 0.25 to 0.75 m H2S04 in concentration. Spontaneous, in situ precipitation of hydronium alunite followed. A high temperature solution speciation model was used for the analysis of the resulting solubility data in order to calculate equilibrium constants for the precipitation reaction.

Jan 1, 1994

By S. B. . Tyrrell

This paper describes research carried out to develop and optimise a process to extract lithium from the processed waste of spent lithium ution of lithium salts can be used to produce a pure lithium hydroxide solution, From this, lithium carbonate is produced, the major precursor for other lithium chemicals and for new lithium batteries. Hence, the recycle loop can be closed. Significant variation in the composition of the battery waste has been observed. Small amounts of metals other than lithium and certain anions can present technical difficulties such as electrode dissolution and membrane fouling. Pre-treatment of the waste, together with an optimum combination of cell materials and operating parameters has been found to enhance separation and alter the energy consumption of the process.

Jan 1, 1999

By Edward P. Hagarty

The Hazardous and Solid Waste Amendments (HSWA) of 1984 added Subtitle I to the Resource Conservation and Recovery Act (RCRA), authorizing the Environmental Protection Agency (EPA) to develop and implement a new regulatory program for Underground Storage Tanks (USTs) containing petroleum and other regulated substances. Technical standards required for release detection, prevention, and correction as necessary to protect human health and the environment were promulgated as described in 53 Federal Register 37082 (September 23, 1988). Virginia State Regulations (VR 680- 13-02) and U.S. Army Regulations require that a Corrective Action Plan and a Site Clearance Report be prepared to explain the details of remediation of any contaminated media. Construction of new buildings is proposed in two different areas at Fort Myer in Arlington, Virginia, where USTs containing gasoline, diesel and heating oil were located. Tightness testing performed on these USTs in September 1991 indicated that some of the tanks were leaking. Many of the tanks were removed for permanent closure. Initial Abatement (excavation of contaminated soil) was &ed out immediately. A detailed Site Characterization Study which included Hydropunch", field screening using immunoassay, and pilot test - dual phase (water and soil gas) extraction was conducted. Environmental media were analyzed for volatiles, semi-volatiles and metals. A detailed risk analysis (RA) was performed to determine risk-based clean up levels for benzene, toluene, ethylbenzene, xylenes (BTEX); polycyclic aromatic hydrocarbons (PAHs); and methyl-tertiary butyl ether (MTBE). The RA also discussed the presence of lead in the soil. Before constructing any buildings in these contaminated areas, remediation must be conducted in accordance with the State, Federal and other applicable regulations. The remedial alternatives evaluated included Vapor Enhanced Groundwater Extraction, Soil Vacuum Extraction, Soil Washing, Soil Steaming, Active and Passive Ventilation SolidificationlStabilization, Vapor Barrier Construction, and Excavation with Off-site Disposal. This paper discusses: (a) delineation of soil contamination @) risk analysis (c) evaluation of remedial alternatives and selection of the most appropriate technology and (d) consideration of various regulatory issues.

Jan 1, 1994

By Mikio Kobayashi

Extraction of valuable metals from sulfide ores continues to be a very important, process and so the strict control of discharge of harmful metals in effluents from refineries becomes more important in the future. The recovery methods for heavy metals have been developed. Some metals such as Se and As are still difficult to be removed to very low concentration, although the techniques for recovery and removal for many kinds of heavy metals have already been developed. Especially, in case of Se the recovery system from water with low concentration has not be developed yet, although the WHO decided Se to be harmful for human beings and then the discharge control is under obligation now. In general Se exists as selenite ion and/or selenate ion in aqueous phase and selenite ion is able to be recovered by coprecipitation with ferric hydroxide or by reduction to solid selenium by general reductants. Selenate ion, however, has a strong resistance to conventional treatments. Therefore the new technique for the recovery of Se from water including selenate ion has to be developed. In this presentation the new approach for removal of selenate ion using the reaction in which ferrous ion is oxidized to ferric ion is presented. Selenate ion is reduced to selenite ion during the reaction and then to solid selenium, while ferrous ion is oxidized to ferric ion. The coexistence of activated carbon is very useful to increase the reaction rate. The use of iron powder is also effective and very useful for reducing gel-like precipitates mainly consisted of ferric hydroxide. The concentration of the residual selenate ion is probably under 0.1 ppm after recovering Se by the mentioned-above approach. In addition to the mechanisms of these reactions, the effects of pH, coexistent positive and negative ions, and reaction temperature are also presented. Furthermore the investigation of the behavior of selenosulfate is presented.

Jan 1, 1998

By Batric Pesic

Silver dissolution with thiourea was studied by using the rotating disk technique. The major parameters studied were: thiourea concentration (0-0.5M), ferric sulfate concentration (0-0.5M), sulfuric acid concentration (0-0.5M), and the effect of many foreign ions (Mn, o.i, Co, Ca, Na, etc.). Temperature effect was studied in the range 5-35 .C. The activation energy was 5.4 Kcal/mole. The dissolution of silver was first order with respect to ferric sulfate, and the secord order with respect to thiourea. Among the additives, copper had a dramatically negative effect. The strong oxidants such as hydrogen peroxide and manganese dioxide were also detrimental for silver dissolution. Silver does not dissolve with thiourea in the absence of ferric ions. Sulfuric acid does not participate in the dissolution reaction either. Chemically, the most important parameter for silver dissolution is the ferric sulfate/thiourea ratio. Thus, in the solutions with excess of ferric sulfate, a solid silver-thiourea complex is formed, which precludes transfer of silver into solution. In the solutions with the excess of thiourea, the free thiourea reacts with formed solid silver-thiourea complex and silver goes into the solution. The solid silver-thiourea complex was characterized according to its chemical composition. The complex contains 6.54%C, 2.49\H, 14.77%N, 16.09%0, 21.62%8, and 37.13% Ag. This composition corresponds to a Ag2so4.3&apos;1U.2ff:i0 compound The soluble silver species are present in the solution as the dimers of AgTU+3 complexes.

Jan 1, 1989

By Kaspar Tall, Dmitri Goljandin, Kristiina Vilsaar, Jaan Kers, Valdek Mikli, Lifeng Zhang, Riho Tarbe, Viktor Laurmaa, Mart Saarna, Priidu Peetsalu

In this paper, the mechanical milling of the Printed Circuit Boards (PCB) was carried out. First goal of the work was to examine the management of the WEEE, in particular the re-use of PCB. Firstly, recycling methods of PCBs were summarized. During the study mechanical separation methods (magnetic-, density- and air separaten), electrical, and chemical methods were examined. Secondly the optimal particle size for air-classification was determined. Several tests were carried out to find the most effective separation method for separation of different material groups from PCB scrap. The new air classification stand was developed for testing the separation of lightweight particles like tinfoil stripes and plastics. The test results showed sufficiently good separation of heavier Al and Cu. For milled materials characterization the SA, IA, laser diffraction analysis and SEM were used. The chemical composition of the PCB powders was studied by means of energy dispersive X-ray microanalysis (EDS).

Jan 1, 2011

By Tamas Kekesi

Anion exchange in HCl media is considered an efficient alternative to the combination of the conventional purification methods. Anion-exchange distribution functions have been determined for cobalt and the main impurity elements by the technique of batch equilibration. Results were confirmed by spectrophotometric investigations and elution tests. Based on the new and the available distribution functions, combined with the assessment of thermodynamic stability, a procedure of anion exchange separation has been devised to eliminate virtually all the impurities from the cobalt-chloride solution. Separation of copper has been enhanced by the introduction of a preliminary step under reduced conditions. The rest of the impurities are eliminated in a second anion-exchange step applying rinsing and elution stages under oxidized conditions. The optimum parameters of the procedure have been determined according to performance characteristics (purification ratios, yields and volume efficiencies) derived from the analysis of elution curves obtained with laboratory scale ion-exchange columns. Special computer programs have been developed to facilitate thermodynamic simulation, analytical correction and data processing.

Jan 1, 2003

By M. Demuth, B. Holleis, M. Potesser, D. Spoljaric

"In 2005, Messer Group established a technology competence centre for metallurgy in Gumpoldskirchen (Austria), with the aim to develop oxygen burners which satisfy today's and upcoming standards of legislation as well as customer requirements. With the assistance of the Development Sponsorship Fund (FFF) of Austria, cooperation with the University of Leoben was agreed on. With the long term experience of the Gas-Warme-Institut ""GWI"" in Essen (Germany) and the University of Leoben, different new burners have been developed.The efficiency of industrial combustion processes can be increased in two ways (which can be seen in Figure 1 ), either by preheating the fuel and combustion air or by adding oxygen. Due to the high 79 % Nz ballast in air combustion, only low flame temperatures can be reached. This results in high heat loss in the exhaust gas, caused by the low combustion efficiency. Oxygen can be introduced into the combustion chamber using different techniques:• Oxygen fuel burners• Direct oxygen injection into the fuel air flame• Underlaying of the fuel air flame• Enrichment of the combustion airIn Figure 2, the theoretical flame temperature for the stoichiometrical combustion of natural gas is plotted as a function of oxygen enrichment. Therefore, it can be concluded that even low enrichment values produce higher flame temperatures and result in higher combustion efficiency."

Jan 1, 2012

By G. Gerbeth, Y. Gelfgat, A. Cramer, A. Bojarevics

The production of highly porous metallic substrates requires an effective and well controlled production of metallic fibres with diameters in the range of 50 to 200 microns. The melt extraction, where a quickly rotating wheel extracts fibres directly out of the inductively heated melt, is a promising technology for that purpose. The main limitations of this process are due to turbulence within the melt and a wavy motion on the surface. Both effects give rise to strong and time dependent deformation of the melt surface which, in turn, causes non-stationary conditions of the contact zone between the extraction wheel and the melt. In the patent literature many examples can be found which try to overcome these problems by submersing mechanical parts directly into, or placing them at least in close vicinity to the melt, aiming at a stabilisation of that contact region. Even made of heat resistant ceramics they suffer from corrosion or cracks and do not work reliable at all. The present work describes a non invasive control mechanism by means of a magnetic field. Model experiments were carried out to study the calm down of the turbulent surface of a inductively stirred melt. The stabilisation of the melt surface has been demonstrated in practise by the installation of a solenoid at a working extraction facility under rough industrial conditions like a powerful induction heating and vacuum.

Jan 1, 1999

By Nagahiro Saito, Takahiro Ishizaki, Mituhito Hirota, Akio Fuwa

"Owing to their extremely high toxicity in the environment, the dioxins have been attracting social, technical and scientific attention in recent years. The authors theoretically had predicted the thermodynamic properties of all the dioxins via quantum chemistry and statistical thermodynamics and elucidated the generation-decomposition behavior of dioxins in the equilibrium calculation· of C-H-0-Cl system. In actual combustion processes, it is said that metallic compounds have much influences on the dioxins behavior. The aim of this study is to reveal the roles of metallic compounds the generation-decomposition behavior of dioxins is revealed from the viewpoints of quantum chemistry. Especially, the catalytic effect of copper has been investigated for the reaction, 2HCl(g)--H2(g}+Cl2(g) and for the etherification reaction from precursors, which is Phenol(g) here, to dioxins. The catalytic role of Cu is shown to have much influence on the generation -decomposition of dioxins.1. IntroductionIt is well known that dioxins are very harmful not only for our health but also for that of our children and grandchildren because they are very stable substance and their reaction rates of decomposition are considerably low. On the other hands, it is not well know how dioxins are generated and decomposed; the generation-decomposition conditions and paths as well as the catalysts to decompose them'1l. The authors believe that the thermodynamic and kinetic study of dioxins is useful to find a solution to these issuers. The authors have been investigating the following problems to reveal the generation-decomposition behavior of dioxins; (a) the prediction of the thermodynamic parameters of dioxins (2), (3), (b) the generation -decomposition behavior of non-chlorinated dioxins by the thermodynamic equilibrium calculations in C-H-O system(4) and (c) the generation-decomposition behavior of dioxins by the thermodynamic equilibrium calculations in C-H-O-CI system(5). Summaries of these thermodynamic researches are as follows.(I) The thermodynamic parameters for dioxins, which had been unknown and/or inaccurate'6 l, could be predicted and are available within the scientific accuracy."

Jan 1, 2000

By Sergio N. Monteiro

The interface between the matrix and the reinforcing fiber plays an important role in the efficiency by which an applied load is transmitted through the composite structure. The shear stress at the fiber/matrix interface can be associated with this load transference and,consequently,affects the composite strength. In the present work, pullout tests were used to evaluate the interfacial shear stress of curaua fiber in epoxy matrix composites. A small critical length was found for the curaua fiber embedded in epoxy, which corresponds to a relatively weak fiber/matrix bond and lower interfacial strength.

Jan 1, 2009

By Florian Kongoli

The production of a homogeneous self-fluxing sinter is an important step in iron making processes. A good sinter should have good permeability and reducibility and has to keep those characteristics for a certain time. An early melt down of the sinter in the blast furnace, where its solid state reduction is essential, would cause many problems such as low permeability and reductibility. Nevertheless, the important factors that influence these characteristics, such as the chemistry of the sinter and the fluxing effect during sintering and sinter reduction conditions have not yet been clarified. In today&apos;s new reality where many new minor components such as Al2O3 and MgO enter to the sinter through raw materials, the quantification of the fluxing effects during sintering becomes even more important. In this work, the liquidus surface and phase relations of the sinter primary melts in the CaO-FeO-Fe203-Si02 system at sintering conditions have been quantified. The fluxing effect of oxygen potential, Al2O3 and MgO has also been quantified by the means of some practical diagrams that can directly help the optimization of the sintering processes.

Jan 1, 2003

By Subagyo

The condition of slag in a pyrometallurgical reactor is vital to ensuring control of the process. A new technique based on multivariate image analysis (MIA) of digital images has been developed to provide an online measurement of important slag characteristics, such as the presence of exposed metal, the presence of solid phases, and temperature. This paper shall describe the technique and provide some results from analysis using industrial plant data.

Jan 1, 2003