Search Documents

By L. M. Pero

The paper summarizes aspects of the recent literature on mineral development in the Third World. The emphasis is on publications covering agreements between host governments and mining companies.

Jan 1, 1985

By William E. Mead

Although this paper has been entitled "Design of Embankments for Tailings Ponds and Waste Dumps," a better title might have been "Site Selection and Design Planning for Tailings Ponds and Waste Dumps," The procedures normally followed in performing the engineering calculations based upon the measured soil properties will not be detailed. Instead, we shall look at the subject in broader perspective which considers the environmental factors and the fundamental design principles. Disposal of waste materials left from the extraction and processing of mineral deposits has become, in recent years, an important engineering consideration for mine and mill operators. Land occupancy and land values almost everywhere are increasing at a rapid rate. So is the size of mine and mill waste dumps, thanks to our advancing technology in mineral beneficiation. Mining companies are being pressured to "clean up" their operations, both literally and in a safety hazard sense. Once, long ago, the miner could use any convenient location to get rid of his mine waste and mill tailings without being concerned over possible infringement on the rights and well-being of the public. Today, however, he must pay close attention to these matters if he wishes to avoid liability suits and the unfavorable reaction of civic groups as well as local and regional government. Most operators keenly sense their increased responsibility, not only because they are legally vulnerable, but because they realize the necessity for sharing space harmoniously with the rest of society.

Jan 1, 1967

By H. F. Ghezzi

The indirect method of drying coal fines is applied to filter cakes which ordinarily contain 22 to 30% moisture and are not readily transportable. The "Thermal Dryer", which operates on the mass transfer principle, has found wide use in coal preparation plants. The thermal dryer is penalized in operation by the necessity of adding coarse coal to the wet fines before entering the dryer body in order to produce a permeable bed, and thus enable hot gases to uniformly contact the wet mass. The ratio of coarse coal to fines varies from 2:1 to as much as 4:1, depending on the average particle size, moisture, and ash content of the fines.

Jan 1, 1985

By K. R. Miller

In recent years, surface mine equipment operators in the Campbell County region of the Wyoming Powder River Basin have found new ways to solve old problems. This paper will examine overburden stripping equipment and techniques by focusing on evolving applications for draglines, shovels, and dozers.

Jan 1, 1998

In west-central England, 183 m (600 ft) below the Cheshire Plain, lie the evaporate remains of an ancient sea. Stratified into nine beds of salt separated by marl bands, the deposit stretches roughly 21 x 12 km (13 x 7.5 miles) and contains reserves of rock salt estimated as high as 400 Gt (440 billion st). The Winsford Salt Works, one of England's largest underground mines, extracts the Cheshire salt and sells it for use as animal feed, for application in de-icing programs, and as a key ingredient in sodium fertilizer production and a variety of other industrial processes. Because road de-icing is an important market, demand for Winsford's salt varies with the severity of British winters. Design capacity is 2.25 Mt/a (2.5 million/year). However, production peaked at 2 Mt (2.2 million st) in 1987. Over the past five years, annual production has averaged 1.6 Mt (1.7 million st). Run-of-mine salt averages 92.5% NaCl, mixed with about 5% marl. The marl was formed by deposition of a reddish dust blown into the Cheshire basin from deserts in what is now central Europe. Association with the marl adds color to the salt, producing tea-colored crystals that resemble unrefined sugar. Adaptation of coal mining systems Rock salt mining in the Winsford district began at least as early as 1682. Mining at the current site dates from 1844 but was shut down from 1892 to 1928. In the early 1900s, a series of catastrophic collapses and floods plagued and ultimately shut down then-active Cheshire brine-salt producers. Subsequently, Winsford reopened and began adapting mechanized underground coal mining systems to rock salt extraction.

Jan 1, 1992

By Sheldon P. Wimpfen

Man is a short time resident of the planet Earth. He does not have the memory to fully comprehend just what is going on. His span of knowledge can be related to the life of the world to see that this is the case. A museum at Grand Canyon features a geologic clock that compresses Earth's age of 4.5 billion years into 24 hours. Man's estimation of the earth's age has changed radically in the past half century. In 1930, one prominent geologist asserted that the age of the Earth was ". . . at least 600 million years." Later, physicists used radioactive clocks to conclude that the Earth's age was 1.6 billion years. More recently, geologists have found rocks in northwestern Australia estimated to have formed 4.5 billion years ago. As we learn more about what is underfoot, the estimate of Earth's age might change again. The Grand Canyon's 24 hour clock shows that the dinosaurs were the dominant life form for 165 million years. Then an event occurred that wiped them out about 65 million years ago. The prevailing theory is that an asteroid struck the Earth and generated enough dust to wipe out the vegetation upon which most dinosaurs fed. During Earth's existence, there have been at least 12 such mass extinctions - the worldwide disappearance of diverse animal groups. On a planet that has been around for 4.5 billion years and that may continue to exist for another 4.5 billion, it seems reasonable to expect that further mass extinction's will occur. According the Grand Canyon's 24hour clock, the 165 million year reign of the dinosaurs amounted to about five minutes. On that 24 hour clock, the world has been dinosaur free for almost two minutes.

Jan 1, 1993

By Carl E. Bagge

It is easy for a coal spokesman to relate to the theme of this meeting--that the decade of the 1970's is pivotal for the mineral industries. For the coal operator, this period is crucial. The coal industry, according to most energy forecasters, must gear its production machinery to meet a sharp rise in the demand for coal--in this decade to sustain inevitable boosts in electricity output, and in the next to start supporting a big new domestic synthetic fuels industry that is already in the formative stage. The logic of that projection flows from a combination of hard circumstances--proved reserves of domestic fluid fuels are dwindling, the hope for bountiful and cheap nuclear power must be indefinitely deferred, and the threat of long-term fuel imports to the national interests is becoming starkly visible. Only coal, with its assets of abundance, security and versatility, offers the nation an adequate and immediate lift out of its current energy crisis. A hard-won expansion of coal production made the critical difference between local power load-shedding and major area blackouts in 1970, the year the energy crisis went public. Coal will have to play that same key role, not just through this pivotal decade but through the turn of the century. But the logic of fuel demand apparently does not always extend to supply. The coal industry has had a huge production job laid out for it by the energy statisticians, but up to now the energy policy-makers have not followed through with the aids and inducements that the coal operator urgently needs to do that job well and completely.

Jan 1, 1972

By M. Solomon

Crushers are designed and manufactured to survive the severe duty of mining environments worldwide. Under these conditions the crusher performance and availability is one of the critical factors in the mine?s production and profitability. Traditionally the development of these machines tends to be experience-based, incremental improvements in design due to challenges of different applications, duty, or manufacturing. In order to better serve the mining industry a new approach was taken to the design of primary crushers. This approach was to focus on safety and maintenance activities. The result of this effort is a new generation of gyratory crushers that can be serviced from above. Using the features of this new generation of crushers to their fullest extent crushing installations have improved safety, reduced design and construction costs, and lowered maintenance requirements. This presentation explores the benefits of two crusher installations utilizing top service crushers.

Jan 1, 2010

By William Gleason

"The Colorado School of Mines has used the Edgar Mine in Idaho Springs as an experimental mine to teach students since 1921. Since the school acquired the former gold, silver, lead and zinc mine, countless students have received hands-on engineering lessons on their way to earning mining engineering degrees. On Dec. 14, the House Subcommittee on Energy and Mineral Resources held a historic field hearing about the future of mining education in the United States in a classroom about 300 m (1,000 ft) inside the Edgar Mine. Representatives Doug Lamborn (R-CO), Rob Bishop (R-UT), Cresent Hardy (R-NV) and Ed Perlmutter (D-CO) were on hand for the first ever congressional hearing held in a mine where they heard testimony supporting the Mining School Enhancement Act, which was introduced to Congress by Hardy and Perlmutter on Oct. 9, 2015. The act, which is part of a larger mining development and reclamation reform package, seeks to address the absence of a viable pipeline necessary to replenish current faculty vacancies in United States Mining Schools. “What better place to hold a hearing to discuss the need for future mining engineering experts,” Subcommittee Chair Lamborn said in his opening statement. “It is a need felt by industry, states, the federal government as well as nonprofits.” The Mining School Enhancement Act would redirect millions of dollars in fees that are being collected from active mining operations to fund the research and educational programs at engineering schools with mining programs. Those fees now are being used in the form of grants awarded by the Surface Mining Control and Reclamation Act of 1977 (SMRCA)."

Jan 1, 2015

By Qingming Feng, Jinhong Zhang

This study investigates the application of fly ash as a high-strength, water-resistant precast construction material through geopolymerization. The experimental results show that working conditions such as water content, sodium hydroxide (NaOH) concentration, curing temperature and curing time significantly affect the mechanical properties of the geopolymer matrix. Through optimization, compressive strength above 100 MPa was achieved, and the optimum working conditions were found to be NaOH concentration of 10 M, water content of approximately 14 to 15 percent, and curing at 90 °C in an oven for one day or at ambient condition for three weeks. Water-soaking tests show that the geopolymerization product has high water resistance without losing noticeable compressive strength even after one month of soaking time. The findings provide a novel method to apply fly ash as a high-strength, water-resistant precast construction material.

By M. L. Leming

The mechanisms of Alkali-Silica Reactivity (ASR) are briefly reviewed, test methods are examined, and typical specifications are discussed. In addition, views on responsibility of the aggregate supplier regarding specifications are presented.

Jan 1, 1995

By James H. Williams

More than 100,000 residents of Springfield and surrounding communities live on karst (sinkhole) terrain on the Springfield Plateau in southwestern Missouri. The city occupier much of the headwaters area of Wilson Creek basin, which is underlain by the Burlington Limestone (Mississippian), a cavernous, massively bedded formation averaging 150 feet in thickness. Sinkholes, some as deep as 75 feet, pock-mark the uplands. Stony red residual clay mantles the pinnacled limestone bedrock. Surface water lost to sinkholes and losing reaches of upstream areas resurges in springs and estevellas (reversible sinkholes) in the lower reaches of Wilson Creek. The Springfield Southwest Treatment Plant, an activated sludge process sewage treatment facility, situated about mid-basin at the confluence of Wilson Creek and a tributary, South Creek, serves the entire city. Effluent from the treatment plant together with industrial, street-wash and other waste from the-headwaters of the basin have degraded both surface and ground water quality in much of the Wilson Creek watershed. The area affected includes Wilson's Creek Battlefield National Park and recreational reaches of James River below the mouth of Wilson Creek.

Jan 1, 1970

By H. H. Murray

In the past thirty years, there have been a large number of ownership changes in the industrial minerals arena and many medium to large companies have made industrial mineral acquisitions. Industrial minerals are exceedingly important to the achievement and maintenance of a high standard of living in the United States and in other developed countries. In the developed countries of the world the value of industrial minerals exceeds the values of the metallic minerals. In the U.S., the value of our industrial minerals is some 2 112 times that of the value of our metallic minerals. Almost every single thing we use or touch in our daily lives can be related to an industrial mineral. Examples are the construction industry, agriculture, ceramics, paper, paint, plastics, electronics, glass, petroleum, and many more in which an industrial mineral or minerals playa functional role. Industrial minerals are exceedingly diverse in their values, properties, and applications. Sand and gravel is an example of an essential industrial mineral commodity which has a low price but moves in very high volumes. Geographic location of this commodity is critical because of transportation costs. High calcium limestone or marble has a moderately high price particularly if it is white enough for use as a pigment or extender. This moves in moderately high tonnages and location is not as critical be-cause it can be shipped for considerable distances and still be competitive. Some specialty industrial minerals such as a white tale or white bentonite sells at a high price at low volumes and geographic location is not a major factor in marketing. Prices of industrial minerals do not tend to be cyclic and generally keep up with inflationary increases. Because of the diversity of industrial minerals very careful analyses of acquisitions or divestitures must be undertaken by buyers and/or sellers in order to prevent serious mistakes.

Jan 1, 1994

By S. S. SHINDE, P. C. JIKAR, N. B. DHOKEY

Mill scale is an oxide waste product of steel mills, containing around 70 percent iron and other allied impurities. In the present context, a dynamic prototype counter-current reactor (CCR) was used for the experimentation and simulation of a particle bed using the discrete element method (DEM). Mill scale was pulverized to ASTM mesh range 140 (106 μm)/+ 270 (53 μm) and oxidized in a CCR to make a single oxide Fe2O3 phase by maintaining the required thermodynamic conditions, such as pure oxygen at 1,100 °C. This oxidized powder was then subjected to a reduction reaction in the CCR, with gas mixture (H2:N2) ratio of 1:4 at 875±5 °C for filling degree, fd , and reactor revolution, ω, ranging from 5.38 to 16.14 percent and 2 to 5 rpm, respectively. A creeping fluid flow condition (Re < 1) and natural heat convection (Gr/Re2 >> 1) were maintained during the solid–gas reaction, and the particle-bed behavior was quantified by Froude number for the optimum operating window. The simulation was validated with the experimental results of reactor reaction product by X-ray diffraction (XRD) and scanning electron microscope (SEM) images.

By William S. Fyfe

The world&apos;s biomass with its species-specific ability to concentrate metallic elements must provide one of the dominant concentration and transport systems for such elements. Given that about thirty elements are now considered bio-essential, for all these biomass may control their environmental behavior. Life appears to be present in almost all places where liquid water is present at temperatures near 100°C or below. In the surface environment a very large array of simple minerals are produced in living cells and such processes can lead to economic concentrations. Because of the specific nature of bioconcentration of elements, in all environments where biomaterials accumulate, interesting metal concentrations may occur or the molecular fragments from bio-degradation may allow specific metal transport and concentration. The scale of biological-inorganic interactions on our planetary surface is still inadequately appreciated.

Jan 1, 2013

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"Prospecting and Exploration. Since the Lake Superior ores occur in pockets or distinct bodies and vary much as to character and location, the actual mining of the ores is preceded by much work of an exploratory character. This work includes prospecting and exploration.Prospecting is the term generally applied to the quest for surface indications of ore, or the conditions which would warrant the expectation of finding ore in the vicinity. It includes such &apos;operations as geological examination, dip needle work, shallow test-pitting, and trenching. The ore bodies of the Mesabi Range are non-magnetic, and dip needle prospecting is therefore valueless. On the Cuyuna range, however, magnetic attraction as evidenced by the dip needle has been extensively employed as a guide to the location of ore deposits; in other localities it has found limited application.Drill Exploration. After the presence of an ore deposit is known or suspected, resort is generally had to exploration by means of diamond or churn drills. On the old ranges geological conditions generally make this manner of ascertaining the exact limits of an ore deposit impracticable; so, if two or three adjacent drill holes develop considerable depths of ore, the sinking of a shaft for underground exploration, development and mining is generally considered warranted. On the Mesabi Range, however, the flat-lying and comparatively shallow characteristics of the ore formation warrant much more extensive drill explorations. On this range, then, an ore body &apos;is almost invariably followed· out with the drills, and its limits are determined to the point where the complete plan of development can be worked out in advance of actual mining operations"

Jan 1, 1920

By A. D. Wunderlich

Providing a safe & secure environment for your employees and other company assets is absolutely necessary in our litigeous society. Security hardware is no different than computers or other technical equipment, in that new equipment is developed each year that makes older equipment obsolete. This presentation will help to explain how your existing security system and security procedures can be updated to meet industry standards without the expenditure of a great deal of money. If you are concerned about potential security problems and how to address these problems, this presentation is a must.

Jan 1, 1995

By Edward K. Davison

The so-called "construction aggregates," sand and gravel, crushed stone, and several kinds of metallurgical slags, are used principally in the construction and maintenance of all kinds of roads, engineering structures, buildings, homes, airports, etc. Production of these aggregates is approaching two billion tons annually. In terms of tonnage produced, sand and gravel has been the leading mineral since 1954, with crushed stone gradually approaching an equal tonnage. Sand and gravel is of widespread occurrence and of wide variation in suitable gradation and quality. It is a low-value, heavy-loading, short-haul commodity. These characteristics account for the historic concentration of production tonnage in and near urban areas where construction activities are concentrated. The combination of improved urban and near-urban highway systems and the steadily rising rail rates for short-haul traffic has fostered a consistent change since World War II from rail to truck transport, with trucks now accounting for more than 807 of the tonnage moving away from the production sites. While there are increasing numbers of exceptions, truck transport of sand and gravel is generally limited to about 30 miles. The expansion of the urban and near-urban areas of even moderate density, which became so pronounced after World War II, has been the source of most of the sand and gravel industry&apos;s environmental difficulties. Dust, noise and truck traffic associated with the operations -- particularly truck traffic -- have, of course, generated public complaint. This has been particularly true in those many cases where housing developments have approached and even surrounded sand and gravel operations which were in operation before the development started.

Jan 1, 1974

By D. Nebbia, R. Aliberti, F. Solesin

The launch of a Tunnel Boring Machine (TBM) is one of the most challenging activity parts of the construction of a tunnel. Challenges are coming from limited space available, learning curve, concurrence of other activities and in some cases from the geological conditions. Launching a TBM is an extraordinary and complicated operation requiring a great level of planning. The Earth Pressure Balance (EPB) TBM named “Chris” was successfully launched for the Northeast Boundary Tunnel, the largest component of the Clean Rivers Project in Washington, DC. Due to space and time constraints, the 8-meter diameter TBM was launched from a single 20-meter diameter shaft, with a 30-meter-long tail tunnel by means of umbilical connections. This paper presents the steps followed during the TBM assembly and launching to complete the excavation of the initial drive of the tunnel maintaining high level of efficiency and quality despite the space constraints. Specifically, it focuses on the methods and phases used to extract the excavated material (muck) from the TBM and from the tunnel, to supply consumables, precast rings and backfill grout. The paper presents results in terms of productivity, lesson learned and possible alternatives to be considered in similar conditions.

Jun 13, 2021

By Fabrizio Fara

The Ship Canal Water Quality Project (SCWQP) includes a 2.7-mile long, 18'-10" internal diameter tunnel which is located inWest Seattle. Tunneling in urban areas and soft ground conditions (Till and Till-like soils in Seattle) is associated with the risk of settlements, especially in presence of groundwater above the alignment. The Designer foresaw the use of soil improvement (jet grouting) outside of the launch shaft to mitigate the risk of flowing ground and to provide a redundant sealing. The Contractor proposed and ultimately successfully executed a different approach by using a “Steel Bell System” or Pressurized Can as described in this paper.

Jun 13, 2023