Search Documents

By M. N. Herrera

The bioleaching of mineral sulfide pulps in a bench-scale rotating drum reactor has been studied. The reactor includes horizontal paddles in the inner wall for lifting of the mineral pulp. The performance of the reactor was tested in the bioleaching of a refractory pyritic gold concentrate in the presence of pure Thiobacillus ferrooxidans strain (ATCC 19859). The concentrate was efficiently bioleached at 50% pulp density with the drum operating at 0.5 -1.0 rpm Attempts of bioleaching the concentrate at the same pulp density in conventional stirred reactor showed severe inhibition of bacterial activity. The results demonstrated that the drum reactor allows to operate at much higher pulp densities than the conventional stirred tank reactor. This behavior is explained in terms of an improvement of the bacterial activity due to a better control of the attrition of the mineral particles.

Jan 1, 1997

By R. G. Swanton

The Bureau of Mines is investigating the leaching of phosphate values from Florida phosphatic clay wastes using sulfuric acid (H2SO4) as the leaching agent and methanol as the solvent. Acid-alcohol leaching studies were done using pure crystalline apatite to investigate potential causes for low extractions. It was found that a barrier layer formed on the surface of the apatite. Initial discovery of the barrier layer was made by analyzing pure apatite samples before and after leaching using an optical microscope. Subsequent Fourier Transform Infrared (FT-IR) analyses proved the coating was calcium sulfate hemihydrate (CaSO4-1/2H2O) and that unreacted apatite existed beneath the coating. Scanning electron microscope (SEM) photographs depict the CaSO4-1/2H2O morphology as long slender crystals adhering to the apatite surface. It was also shown that grinding the leached tailings and leaching again in the H2SO4-methanol system resulted in additional phosphate extraction.

Jan 1, 1991

By Robert A. Jankowski, Ellsworth R. Spencer, Jay F. Colinet

Longwall mining is the most productive method of under- ground coal mining in the United States (US.), and record levels of production have been reached in recent years. These ever-improving production levels have the potential to generate significantly higher quantities of respirable dust. Consequently, the longwall industry continues to struggle with controlling dust liberation and maintaining compliance with the federally-mandated respirable dust standard. In response, longwall operators have in- creased the application of primary dust controls, airflow and water flow, in an effort to improve respirable dust control and reduce worker exposure. Pittsburgh Research Center (PRC) personnel conducted dust surveys at 13 longwalls operating throughout the U.S. and collected information to: identify current operating practices on these longwalls, identify the types of dust controls in use, document the levels at which these controls are being applied, and measure the respirable dust levels present. This data was analyzed to quantify the dust levels generated by the major sources on the longwall section and to evaluate the relative effectiveness of the control technologies in use.

Jan 1, 1997

By A. T. Yu

Technology and economies of scale have, in the past decade, brought about the emergence of giant vessels. Meanwhile, to answer the need for rapid dispatch, as a means of combating the proportionately far greater demurrage charges, shiploading and unloading speeds have soared (Ref. 1, 2, 3). As the loading and unloading rates have dramatically increased, so has the cloud of dust grown in unbearable proportions. It not only has threatened to be a real menace to machinery and men, but in certain instances has also seriously jeopardized fish and marine life (Ref. 4). In an era when ecology is king, dust in shiploading and unloading can no longer be shrugged off as a mere public nuisance, and its control is now duly recognized as of grave concern to all. Even if public outcry were not a problem, from the operator's own parochial point of view, dust can adversely affect productivity and the well-being of the operating personnel. Without adequate control, it can also result in costly equipment maintenance, particularly when the dust is micronic in size, and abrasive. The Hierarchy of Control Techniques Given the great fortune of not yet having to deal with gas and odors, in the jargon of pollution control, our problem is confined to having to control "particulates" only. To deal with "particulates", the myriad of dust control techniques can be utterly confusing to those who are not entirely well versed in the methodology. Our analysis of what is available to date results in the following hierarchy of logical preferences: 1. Prevention 2. Removal 3. Suppression 4. Containment 5. Dilution Since it deals with the root cause, prevention always outranks the cure. Once the dust is generated, removal nips it in the bud. Only when dust removal is

Jan 1, 1972

By C. C. Huang

Rare earth compounds, such as samarium-cobalt compounds and neodymium-icon compounds, are being used more often for the manufacture of permanent magnets, because these materials permit the production of permanent magnets with higher magnetic energy potential than the conventional ferrite magnets. Especially, the recent rapid developments in the field of electronics and electro-technology have demanded an increased production of rare earth magnets. Unlike ferrite, which is typically produced by a wet process, rare earths can be ground and classified either in a wet or dry process. In the past, batch ball mills, through-pass ball mills in circuit with air classifiers, and conventional jet mills were primarily employed for the dry processing. These methods, however, have suffered from the problems, for example, wear and contamination, low product quality In particle size distribution, difficult to adopt inert-gas operation, and high specific energy consumption. In this report, dry processing of rare earth powders will be presented, especially ultrafine grinding with fluidized bed jet mill.

Jan 1, 1993

By C. E. Jordan

The U.S. Bureau of Mines investigated flotation hydrodynamics to improve the recovery of coarse phosphate. Fluid velocity profile measurements were used to characterize the hydrodynamics within commercial phosphate flotation cells and laboratory flotation cells. The effects of agitation, aeration, and pH on coarse phosphate recovery were measured in the laboratory flotation cells and correlated with the hydrodynamics measurements. Test results revealed that the agitation energy and aeration level had a significant effect upon flotation response. By optimizing these two parameters, 92 pct of the phosphate was recovered in a rougher flotation concentrate grading 28 pct P2O5?

Jan 1, 1994

By H. Suharyono

A laboratory investigation of flocculation following polymer addition during slurry flow through pipes and in-line (static) mixers is described. Results are presented showing the effects of flow velocity, pipe length, in-line mixer elements and the use of multiple addition points on flocculation performance as measured by settling rate and supernatant turbidity. The effects of agitation and mixing time are shown to be generally consistent with the results of equivalent tests, both batch and continuous, conducted in stirred tanks.

Jan 1, 1995

By H. Ban

Triboelectrostatic separation tests were performed on a bench-scale, analytical separator using coal, coal combustion fly ash and mineral samples. Fractions of separated samples were collected and analyzed to characterize the performance of the separation. Particle size distribution and morphological characteristics for these samples were analyzed by optical microscopy, and scanning electron microscopy (SEM). It was found that smaller size fractions of a fly ash sample had better separation than the full sized parent fly ash sample, indicating interference or particle-particle interactions during the separation process. It was also observed experimentally that small kaolin particles attach to the surface of large silica spheres, causing charge neutralization and subsequent low separation efficiency.

Jan 1, 1997

By M. J. Gula

In the solvent extraction -electrowinning recovery of copper from oxide or sulfide ores there is a continuous transfer of iron and other impurities from the primary leach solution to the copper electrowinning electrolyte via chemical transfer or mechanical entrainment. Iron is the principal impurity that has to be controlled in the electrolyte by a "bleeding" of the electrowinning solution. This bleeding transfers copper and sulfuric acid back to the primary leach circuit along with the iron. Copper is recovered via the solvent extraction process and generally the sulfuric acid is used as a reagent in leaching. Unfortunately, cobalt, which is added to the electrowinning solution to modify the anodic process, is irreversibly lost through the bleeding operation. This cobalt loss represents a significant operating cost to SX-EW copper producers. DiphonixTM ion exchange resin contains diphosphonic acid and sulfonic acid functional groups on a polystyrene-divinyl benzene matrix. This resin has been found to strongly and selectively extract ferric ion from copper sulfate -sulfuric acid solutions containing cobalt. Thus, an ion exchange process using DiphonixTM resin for the control of iron has been developed to replace the conventional bleed stream process. The new process minimizes the loss of cobalt from the electrowinning circuit and strips the iron into a sulfate based solution suitable for leach solution makeup. In addition, this process can effect a lowering of the total iron concentration in the electrolyte circuit with an associated increase in current efficiency. In this paper, data on the loading and elution of iron are presented. Laboratory and pilot scale data will be discussed along with information on process design and comparative economics.

Jan 1, 1996

By J. Groff

The Getchell and Twin Creeks mines are located along a north-northeast trending structural zone in Humboldt county, Nevada approximately 40 miles northeast of the town of Winnemucca. Gold mineralization at the Getchell mine is represented principally by sulfide-rich ores, which contain significant amounts of realgar and\ orpiment, with the gold being recovered through processes which involve pressure oxidation. In contrast, oxide ores are currently being mined and processed at the Twin Creeks mine although large reserves of sulfide ores, some of which contain orpiment-realgar-stibnite, have been defined (Bloomstein et al., 1990). The Getchell and Twin Creeks mines represent major gold orebodies but very little has been published pertaining to mineral paragenesis and the characteristics of ore-forming fluids for these deposits.

Jan 1, 1994

By Paul Basinski

The Northern Reese River Valley is in west-central Lander County approximately 31 miles north of Austin, Nevada in the north-central Basin and Range Province (Figure 1). Authigenic zeolites, which were previously undescribed in the literature, are voluminous in this small sedimentary basin. Uranium mineralization is also abundant in this study area. Until now, what we believe to be cause and effect have not been put together. X-ray diffraction, differential thermal analysis, and scanning electron microscopy reveal clinoptilolite, erionite, analcime, and minor chabazite to be present (Figures 2, 3). Assays show uranium to be present in thicknesses up to 0.7 meters at amounts up to 0.10% eU308. The sediments in the Northern Reese River Valley belong to the Mio-Pliocene Humboldt Formation equivalents. This formation consists largely of tuffacious lacustrine and fluviatile sedimentary rocks. Mudstone is the dominant lithology and intercalated thin zeolite strata (usually less than 0.6 meter thick) are present. Zeolites in the Northern Reese River Valley were diagenetically derived from rhyolitic glass deposited in a shallow, saline-alkaline lake under arid to semi-arid conditions. Clinoptilolite from the study area was K-Ar dated at approximately 4.7 + 0.5 million years which corresponds to Middle Pliocene age (Krueger and Basinski, in press). This age is further substantiated by Middle Pliocene mammalian fauna collected in the vicinity by Deffeyes (1).

Jan 1, 1979

By J. D. Grenia

The Buick Mine is a joint venture of American Metals Climax, Inc., and Homestake Mining Company located 120 miles by road southwest of St. Louis, near the village of Boss, in the 'New Missouri Lead Belt' (See Figure 1). Since start-up in 1969, over four million tons of lead-zinc ore have been mined and milled at Buick. Situated about 1,100 feet below the surface at an elevation 270 feet above sea level, the flat lying sinuous ore bodies are up to 250 feet wide, 85 feet high and several thousand feet long. Mineralization is galena, sphalerite and chalcopyrite in dolomite, Access to the mine is through two 18'Ø concrete lined vertical shafts - one for servicing and the other for hoisting ore (See Figure 2). The mine is being worked by a modified room and pillar method using both rubber tired equipment and a sub-level rail haulage. Ore is broken from first pass headings, back and bench faces and transported by load-haul-dump units to ore passes located on 900 foot centers. The ore is pulled from chutes on the sublevel 90 feet below into 15 ton bottom dump cars and delivered in 10 car lots by a 15 ton diesel locomotive to a 42" gyratory crusher (See Figure 3). A recent innovation has been the introduction of two 50 ton trucks with plans to haul up to 60% of the ore on the mining level to an ore pass feeding directly to the primary crusher (See Figure 4). Ventilation raises up to 16'Ø, which were originally planned for 900 foot centers, are now driven on 450 foot centers.

Jan 1, 1973

By J. E. Lema

America's bulk commodity transportation systems have taken on a new look in the 1970's and 1980's. Railroad systems, barge lines providing inland and intra- coastal waterway transportation, and Great Lakes carriers have undergone substantial changes through mergers and acquisitions, consolidations of ownership and control, and construction of modern intermodal transportation facilities linking railroads and water carriers. The new look has generated some concerns and opportunities with regard to producers and shippers of bulk commodities which are characterized by the necessity of moving large quantities of heavy materials long distances. Clearly such transportation requirements call for efficient railroad and water carrier services. Shippers of commodities like coal, grain, .chemicals, minerals, ores, forest products, petroleum products, and heavy manufactured goods find reductions in transportation competition lead to concerns that rates charged by carriers will not be sufficiently constrained by market forces. At the same time, new policies on contracting for railroad services can lead to greater efficiencies, a rewarding opportunity for carriers which should be shared with shippers and consumers of bulk commodities. Then, of course, there's a related problem that in the absence of effective competition, the benefits of increased carrier efficiency will not be passed on, in part, to shippers and consumers, causing losses in markets for producers.

Jan 1, 1986

By Richard D. Zigmond

In this paper, a computer program that has been developed for determining the capital and operating costs for coal preparation plants is described along with its applications. The logic of the computer program is based upon the results of a survey of existing preparation plants, operators, plant contractors, equipment manufacturers, and consulting firms. This survey provided information on plant performance, order-of-magnitude costs, and costing procedures. Additionally, an extensive cost data file for the major capital equipment in coal preparation plants has been developed. Using the washability data and the computer program outputs, the cleaning costs per million Btu can be calculated. Details about the program and its applications can be found in a report by the authors (Zigmond et al., 1979).

Jan 1, 1981

By B. Kolonja

This paper considers simulation of truck dispatching system designs using maximum expected production of the truck-shovel system as the measure of performance. Two methods are utilized, multiple comparisons with the best (MCB) and the combination of MCB and the variance reduction technique known as common random numbers (CRN). These two techniques are compared via simulation experiments. The results show that the combined procedure of MCB with CRN is the superior tool to reduce the total number of replications needed to ensure the specified probability of correct selection over the finite number of designing systems. In this case study, MCB with CRN reduces the variance by 29% and the number of required replications by 48%. Also, the MCB with CRN procedure narrowed the confidence interval by 18%.

Jan 1, 1994

By Y. Zeng

Experiments were performed under batchwise wet grinding conditions with dolomite mineral. The vibration signal was received by an accelerometer and transmitted to a mini-processor. The signal was first stored on a digital tape recorder (OAT) in voltage format during the grinding tests. The original signal was then re-sampled and converted into data format for IBM or compatible personal computer by a digital oscilloscope. The root-mean-square (RMS) and power spectrum was estimated on the time-domain vibration signal. A partial correlation analysis was applied to the frequency-domain signal to detect the non-zero correlation between the frequency bands and the operating parameters. A multiple stepwise regression was used to locate the key frequency bands for describing a particular operating parameter. After vibration analysis, the operating parameters in grinding, for example, the mill speed, the powder filling, the pulp density, the pulp temperature and the particle size were found to be strongly correlated with a few frequency bands. The grinding process could therefore be monitored using the vibration signal.

Jan 1, 1992

By F. Segobia, M. Portal, F. Ysla, A. Mujica, L. Goicochea

The “Building Our Future” project is a collaborative initiative between the UNC SME Student Chapter and the Water and Earth Museum (MAT) of Asociación Los Andes Cajamarca (ALAC), both corporate entities of Newmont Yanacocha. Its mission is to promote responsible and sustainable mining among new generations while fostering a culture of equality and respect. This comprehensive educational program integrates sustainable development goals and includes workshops led professionals and external experts who share their personal stories to inspire students from rural and urban educational institutions to follow their dreams. Additionally, for this year 2024, the project development and implemented an interactive mobile application that educates users about the use of minerals in everyday life through four levels: Minerals in the Home, Minerals in Medicine, Minerals in Transportation, and Minerals in Agriculture. This multi-faceted approach seeks to raise awareness about the importance of mining in Peru’s economic, environmental, and social development, ultimately fostering a new generation of informed and engaged citizens who understand the vital role of mining in a sustainable future.

Feb 1, 2025

By G. L. Barthauer

It is a distinct privilege to have the opportunity of addressing this group today. Although I, myself, am not a mining engineer, I have always had profound admiration and respect for those of you who each day live and work according to the tenets of Murphy's Law. Murphy, as some of you may know, was an Irish philosopher whose sole contribution to his field was the observation, "In the mining industry, if anything can possibly go wrong, it will!" You have heard this afternoon a variety of papers, touching on or describing in some detail imminent problems which presently face the coal industry. Many of these problems show no signs of diminishing. Actually, there is good reason to believe that they will intensify as governing bodies pass additional enabling legislation and regulatory agencies adopt more stringent "Rules and Regulations". In many cases, these groups are seemingly oblivious or indifferent to either cost factors or technical problems involved in achieving the desired goals.

Jan 1, 1967

By Z. Yu

The effect of particle size on coal dewatering has been well recognized However, there are no systematic studies on ultrafine coal dewatering. The results discussed last year revealed the effect of flocculant type and coal wettability on the filtration of ultrafine coal In this paper, the differences in dewatering between -25 µ m ultrafine and -500 µ m fine coal with addition of flocculants, surfactants and oil-emulsions in vacuum filtration are further investigated Significant differences were observed in the reduction of the cake moisture. The utilized emulsions were found to be very powerful and promising filtration aids for both ultrafine and fine fractions of hydrophobic and hydrophilic coal

Jan 1, 1995

By M. Ramachandran, R. G. Reddy

"A direct route for the reduction of magnesium oxide to magnesium using thermal plasma processing, with methane as the reducing gas, has been systematically evaluated. A feasibility study of the reduction reaction has been performed on the MgO-CH4 system at different methane concentrations and temperatures. The effects of changes in the key process parameters, such as the oxide-to-methane ratio and plasma power, on the yield of magnesium have been systematically evaluated. A maximum yield of about 61 mol% Mg was obtained using power of 20.0 kW and a molar ratio of MgO:CH4=1:1. Phase, morphological, elemental and binding energy analyses were performed on the product powders to understand the reduction reaction. Surface oxidation was observed in smaller magnesium particles in all the experiments, while the in-situ sintering of magnesium rods was observed at a molar ratio of MgO:CH4=1:1.5. Magnesium carbide (Mg2C3) was observed in the product, and its mechanism of formation is proposed using phase equilibrium data and a predominance diagram.IntroductionMagnesium has an excellent combination of low density and high strength. These properties have increased worldwide demand for and use of magnesium. Two major processes are used in the commercial synthesis of magnesium metal. The first method is electrolytic reduction and the second is thermal reduction using Pidgeon process. These processes can be classified as traditional techniques, but there are numerous emerging technologies that aim at reducing the production cost of Mg, its environmental impact and energy consumption. Thermal plasma processing is one emerging technique that has great potential in all the abovementioned key areas of magnesium production.Traditional reduction techniques. Two major reduction techniques, namely electrolytic and thermal reduction, have been used in the commercial production of magnesium. Electrolytic reduction is typically carried out in electrolytic cells from magnesium chloride (obtained from seawater or well and lake brines) (Tripp, 2009). The following simplified reaction shows the reduction of magnesium chloride to liquid magnesium and chlorine gas:"

Jan 1, 2015