Search Documents

By William R. Bond

The pressure/vacuum lysimeter is being used as an effective vadose zone monitoring device for mining heap leach facilities, tailing disposal ponds and tailing waste sites. Their use has proven reliable for baseline data collection, early warning leakage detection and analyzing geochemical variations in the vadose zone. The lysimeter structure utilizes a closed cylindrical chamber made of PVC or inert material. The soil water intake portion of the cylinder is made of a porous material of low permeability. The application of vacuum or pressure to the unit is via two access tubes from the ground surface. Available soil moisture is drawn by vacuum through porous material into the lysimeter chamber and then collected from the access tubes. Case studies show their usefulness for monitoring around a uranium tailing pond constructed in glacial till material, under heap leach pads and pregnant, barren, and overflow ponds, and investigating the movement of contaminant moisture through old tailing deposits. Relatively easy to install and sample, regulatory agencies and facility operators are accepting and negotiating for their application as a site integrity monitoring device and unsaturated zone research tool. Their use at heap leach facilities lends credibility to solution balance calculations when considering a leachate loss of 5 or 10 percent can make or break a mine's profitability.

Jan 1, 1984

By C. Braux

The aim of this study was to develop an integrated approach to enable identification of areas favourable for the presence of massive sulphide deposits in a given region (Las Herrerias, Spain). It is based on geochemical soil exploration, geophysical surveying (ground gravimetry), detailed geological mapping and a knowledge of the deposits of the South Iberian Massive Sulphide Belt. The multi-dataset approach consists, in the first instance, in standardizing and combining all the geochemical data with reference to their geological setting. Next, the "heavy" anomalies are extracted from the gravimetric survey, regardless of the surrounding context (heavy or light). The results from these two stages are then crossed, so that areas where heavy anomalies are associated with geochemical anomalies can be identified and classified. Crossing the geochemical and geophysical data enables a much tighter selection of anomalies than does the manual superposition of data provided by each method (geology, geophysics, geochemistry).

Jan 1, 1994

By M. A. Kaufman

In this paper I will attempt to present an up to date review of the type of exploration' that has previously been carried out in Alaska, discuss some of the more significant past producers and recent discoveries, and suggest some approaches to future exploration. Hopefully this information may be of some use to those parties tempting to evaluate Alaska's non ferrous, non placer, metal potential or contemplating initiation of exploration in the state. II. SUMMARY AND CONCLUSIONS Past production of non ferrous metals from lode deposits in Alaska has been meager considering the size of the state. Since there have been no major lode mines operative in Alaska since World War II, and since logistical conditions vary throughout the state, it is not possible to generalize with respect to mining costs in Alaska as compared to those in other areas. There seems to be little question, however, that a major deposit situated in a reasonably favorable location' could be profitably operating at present. Host of the known metal prospects in Alaska were discovered by early gold prospectors prior to World War I. From World War I through World War II exploration consisted chiefly of surface prospecting by prospectors on a diminished scale, as compared to the early gold rush days, drilling of some prospects by the U.S.B.M,, and occasional mine or prospect evaluations by mining companies. From the end of World War II to the present time, there has been a generally steady increase in exploration by mining companies consisting chiefly of prospect and district evaluations, large scale aerial reconnaissance programs in search of color anomalies, and regional drainage geochemical surveys. The post World War II increase in mining company exploration has not been matched by an increase in conventional surface prospecting.

Jan 1, 1972

By Luther W. Hyde

Ground water, one of Florida's most valuable resources, is also one of its most abundant. The State is fortunate to have several prolific ground- water reservoirs that yield tremendous quantities of water to wells and to some of the world's largest springs. These ground-water reservoirs, or aquifers are of two types artesian and nonarteaian. Ad artesian aquifer is one that contains water under sufficient pressure to rise above the top of the oontaining formation. A nonartesian aquifer is one that contains water which is not confined, and the upper water surface (water table) is free to rise and fall. The principal source of ground water in Florida is the artesian Floridan aquifer which supplies most of the water users in the State. Nonartesian sources include the Biscayne aquifer of southeastern Florida, the sand-and-gravel aquifer of extreme western Florida, and a shallow aquifer which lies at depths of less than 100 feet over much of the State. The accompanying map shows the approximate areas where these aquifers are the main source of supply; however, the boundaries do not represent the areal extents of the aquifers. For example, the Floridan aquifer extends beyond the southern boundary shown on the map, but it is not of great economic significance there because the water is highly mineralized. Aquifers other than the four described occur in the State, but they are, for the most part, of minor significance. One of these is an artesian aquifer which is formed by permeable zones that occur locally within the confining beds above the Floridan aquifer.

Jan 1, 1966

By Paul Culvenor, Brad Gyngell

Large language models (LLMs) have generated a lot of hype since ChatGPT was released in early 2023. In essence, they allow people to interact with computer systems through natural language and have the ability to generate highly complex text, images and videos (Patil and Gudivada, 2024). It is clear that this technology has significant potential, however most mining companies have not yet found practical applications for it within their operations. In this paper, we present a range of such applications along with the tactical considerations associated with developing and implementing them. We have identified use cases across a variety of operational and functional areas within the mining industry and evaluated them based on their potential business value and ease of implementation. Firstly, we provide an overview of how LLMs work and a review of how LLMs are being applied in other industries to provide best practice inspiration for mining. Next, we present a list of possible applications in mining and a critical assessment of each use case. This section also includes a technical deep dive into the different methodologies for developing the technologies as well as an analysis of barriers to adoption within mining organizations. Finally, we share a discussion of the potential path forward for LLMs in mining and the impact they could have on the industry. We analyze the potential differences between early adopters and laggards in the artificial intelligence (AI) space. This research draws on interviews and surveys with artificial intelligence experts as well as mining subject matter experts to connect cutting edge thought leadership with the specific problems faced by our industry.

Feb 1, 2025

By Barbara H. Carroll

In order to rapidly evaluate an area for its mineral potential, a reconnaissance exploration program generally includes the following: 1. Outlining an area of interest 2. Identifying known mineral deposits 3. Bibliographic search of the literature 4. Evaluation of geochemical and geophysical surveys 5. Compilation and review of geologic maps The information now available from various government agencies regarding the mineral deposits, geology, and geochemistry may be integrated and used as a tool to rapidly evaluate an area before the field season. The databases most commonly used in the United States are the USBM MAS/HILS system and the USGS MRDS system for their information on mineral deposits; GEOREF and GEOARCHIVE for bibliographic information; and NURE data for the geochemistry and geophysics. In conjunction with the project geologist, this information may be used to plot known deposits and their geochemical signature as well as any other areas of like signature for further examination.

Jan 1, 1985

By James R. Aggson

This paper summarizes the research effort that was conducted as part of a cooperative agreement between the U.S. Bureau of Mines, Denver Mining Research Center and the Pittston Company. The objective of this investigation was to further the understanding of the floor heave ground control problems that have plagued underground mining of the Beckley coalbed in southern West Virginia. Floor heave is both economically and structurally undesirable. Floor heave is accompanied by a redistribution of stresses and loads that are associated with an underground opening. This redistribution of stresses may cause roof or pillar problems that otherwise would not have occurred. The floor heave that occurs in the Beckley coalbed is not cons1dered to be caused by "squeezing" or plastic flow of the materials involved. The "squeezing" type floor heave is normally associated with relatively weak floor members that contain significant amounts of clay mineralization. The floor members in the Beckley coalbed are competent, relatively strong materials which fail in a manner that can best be described by the term "buckling." This buckling-type failure is indirectly related to the time-dependent deformation properties of the materials involved, but is considered to be more of a slender column, or panel, type failure than a "squeeze" or "flow"-related failure. The Beckley coalbed has had a history of floor heave ground control problems. The Glen Rogers mine, which opened in the 1920's, experienced extensive floor heave. In a report dated April 1929, James P. Keatley of the West Virginia State Department of Mines described the floor heave in the Glen Rogers mine. Several observations listed in the Glen Rogers report that appear to be consistent with current observations follow: 1. Water plays no apparent part in the floor heave process. 2. No evidence of gas has been found in the floor. 3. The thickness of the overburden, which varies from 183 to 396 m (600 to 1300 ft), has no relationship to the floor heave. In the conclusions of the 1929 report on the Glen Rogers mine, Keatley states, "A statement in brief as to the cause (of floor heave) would lie that an undetermined natural condition doubtless augmented by former and present mining methods causes the bottom to heave." As this report will show, Mr. Keatley's insight into the problem was most accurate. The "undetermined natural condition" is the existence of a biaxial, horizontal, compressive stress field. This stress field is in excess of that which would be expected from gravity loading. This stress field and the material properties of the floor rock combine to cause the floor heave that has been experienced. The floor heave that occurs in the Beckley seam generally occurs as arching, with a tension fracture, near the center of the floor span or as a break near the rib followed by vertical deflection (of the floor) at the rib and sloping of the floor across the entry. Examples of the floor heave are shown in Figures 1 and 2. The two types of floor heave are merely different manifestations of the same basic failure mechanism. When the entries experiencing floor heave were identified on a map of the mine under investigation, it was apparent that there was a relationship between the floor heave and the direction of the entries. The main entries, which are used for ventilation and haulage, experienced the majority of the floor heave. This directional relationship suggested a directionally related loading mechanism, or more specifically, a biaxial, horizontal stress field that exceeds what would be expected by gravity loading. Since the main entries were oriented at a bearing of N25oW, it was hypothesized that the maximum compressive component of the horizontal stress field was at 90° to these entries or at a bearing of N65oE. An in Situ testing program was developed to test this hypothesis and investigate the floor heave problem.

Jan 1, 1978

By Stephen J. Crittenden

Deep gas and oil production has been substantially increased over prolonged periods through the use of sintered bauxite propping agents. Since its inception in 1976, over 170,000,000 pounds of high strength ceramic proppants have been employed. Recent field evaluations and economic analysis demonstrate the superiority of sintered bauxite proppant over quartz sand. This paper describes the development, application, field results, and product evolution of sintered bauxite.

Jan 1, 1983

By R. K. Mehta, K. N. Han, P. B. Queneau, V. Dieudonne

A study based on a statistically designed sets of experiments (central composite design) was conducted to determine the optimum conditions for leaching a subbituminous coal (7.0 % ash) from the middle Wyodak seam in mild sulfuric acid solutions. The statistical analysis was conducted with the ash content and ash removal as the dependent variables and with the coal loading, acid concentration, ferric ion concentration, and temperature as the independent variables. Treatment of the experimental data via a simple genetic algorithm (GA) revealed that acid concentration and temperature are the two most critical variables. Unlike the case with bituminous coal, the ferric ions addition shows no beneficial effect. The optimum "macro response" predicted by GA was verified experimentally; the ash content was reduced to 2.7%, which is close to the value predicted by GA. The ash content was further reduced to 1.7% in a two-stage leaching process devised by incorporating the optimization results with that of leaching kinetic studies.

Jan 1, 1993

By Charles Kocsis, Pedro Nascimento, W. Patrick Arnott, Samuel J. Taylor

Respirable crystalline silica (RCS) is an inhalation health hazard for mining and industrial work environments and must be monitored. We provide theoretical analysis of real-time measurements for determining RCS mass concentration without the use of filters by using photoacoustic spectroscopy. The suspended dust in the mine air can be continuously sampled by the photoacoustic instrument. A tunable quantum cascade laser is the light source, allowing for determination of interferences such as kaolinite, coal dust, and water vapor. The most useful spectral region is found to be between 11 and 13 μm. Absorption by water vapor, and, to a lesser extent, carbon dioxide, in this spectral region has gaps that allow for quantification of the aforementioned dust species as well as a convenient check on the calibration of the instrument. This work brings photoacoustic measurement of aerosol to the mid infrared range where spectrally dependent light absorption can be used to quantify dust composition and mass concentration.

Jul 31, 2022

By M. Ge, C. Mborah

"The acoustic emission/microseismic monitoring (AE/MS) technique has widely been used in the mining environment for the monitoring of rock mass stability. A successful implementation of the method is hinged on being able to accurately determine the P- or S-wave arrival which is then used in the determination of the source of an event. Determination of the arrival phase is usually performed visually by a human expert. However, the mining environment is characterized by high noise levels and different noise types of varying intensities. Therefore, performing manual phase picking on time series data acquired from the AE/MS monitoring system can sometimes be tedious and time consuming if not impossible. In this paper, a proposal for improving manual P-wave phase arrival picks is discussed. The method involves the filtering of the AE/MS data using a stationary discrete wavelet transform (SDWT) method. After filtering, appropriate scales/levels of the multi-level decomposition process are then selected for further processing. The first step in the picking process after filtering, requires the computation of the signal power and the root mean square (RMS) using the signal amplitudes at each scale. The preliminary P-phase arrival time is picked using the results of the calculated power and RMS values respectively. The calculated RMS values are then superimposed on the calculated power values to determine the final arrival picks. If the arrival time picks obtained by both methods coincide or are within 5 to 10 sample points, the pick is considered reliable. The accuracy of the method was verified using AE/MS data from two datasets obtained from two separate underground mines. The results of the study showed that the picking method is reliable and robust. Based on the data studied, it can be concluded that the method will help reduce the time usually spent in processing AE/MS data from mines. INTRODUCTION A successful identification and location of the source of acoustic emission/microseismic (AE/MS) events is mainly dependent on the onset time of the P-wave phase. In many seismic networks, initial picks are performed by picking algorithms followed by manual picks by human experts. If the waveform signal-to-noise ratio (SNR) is low, the P-wave onset time picks by the human expert is generally reliable and accurate [1]. However, for waveforms with high SNR, picking of the P-wave onset could be a major challenge. Also, due to the volume of data acquired daily, manual processing could be stressful and time consuming [2]. These challenges continue to provide motivation for alternative means of providing reliable and efficient ways of improving manual phase picking. The AE/MS technique has been an intergral part of safety monitoring in mines [3] due to its capacity to identify zones of instability in a monitoring area. To obtain an accurate source of an AE/MS event however depends on the quality of the data used for P-wave phase picking [4, 5]. AE/MS data from mines are generally contaminated with excessive background noise generated by the different mining operations. The AE/MS signals of interest are mostly buried in background noise which makes it difficult to pick the P-wave phase arrivals [4]. Processing AE/MS data acquired in noisy environment remains a major challenge due to the weak nature of AE/MS signals [6]. As noted by [4] most of the data recorded in the mine environment are mainly due to events not related to AE/MS events of interest. The complexity of data in this type of environment makes the detection and picking of P-wave arrival by human experts a very difficult task."

Jan 1, 2017

By Verya Nasri

This paper will present the design and construction of a deep underground station of the Réseau Express Métropolitain (REM) project; the Édouard Montpetit station. The Édouard-Monpetit station is an interchange station that will connect the deeply sitting REM tracks to the existing metro station of the same name located closer to the surface. Édouard-Montpetit station is expected to be the deepest in North America, surpassing the famous Forest Glen Station. The various challenges and solutions put forth for the successful completion of this underground work are presented to serve as a valuable example for future deep excavation performed in urban area, in the close vicinity of highly sensitive structures.

Jun 13, 2021

Optimal gold recoveries largely depend on efficient liberation of the gold or gold-bearing minerals as well as on maximum access for the lixiviant. Thus, crushing and grinding may become the most costly part of gold ore processing. It may, in fact, represent 50% to 70% of a plant's operating costs (Michaelis, 1989). The increasing significance of refractory gold will require even more cost-efficient comminution of ultrafine sulfides and/or native gold. Transitional ore zones with semi refractory gold may respond to direct leaching if better particle fracturing is being achieved (Baum, 1991, 1993a). Many oxide ores have been left in the ground because they were unsuitable for heap leaching since conventional comminution could not facilitate economic gold extraction. Also, the costs of conventional bal1 mill operations did not permit the recovery of gold from many ultrafine, low-grade refractory ores. As shown by Marsden et al. (1993), the trend to treat ores with progressively lower grades will involve power-and leach-efficient grinding applications. Our current laboratory work shows that high-pressure grinding roll (HPGR) Polycom grinding may enable many mining companies to add large amounts of these "non-leachable" ores to their current heap or mill leach feeds. This finding may dramatically change the economics of many oxide gold ore operations and may add significant reserves to ores amenable to direct cyanidation.

Jan 1, 1994

By H. Sevim

Long term production planning in open pit mines requires the determination of cutoff grade, mining and milling production rates, mining sequence, mine life, and ultimate pit limits. These variables interact in a circular fashion, that is, the value of a variable can not be determined without the knowledge of the value of the preceding variable in the circle. Therefore, a genuine solution to the problem necessitates simultaneous determination of the variables. Such a solution methodology, comprised of a group of heuristic algorithms and an unconventional dynamic programming algorithm, is described in this paper. The methodology is applied to a small size Western US gold deposit to illustrate its logic and capabilities.

Jan 1, 1995

By Clark B. Risler

Conveyors constitute a critical artery, essential to the successful operation of most ore processing plants. Technological progress is permitting the recovery of metal from low grade ores which previously could not be worked economically. Significant in this progress are improved material handling techniques highlighted by the frequent and successful application of conveyors. From the standpoint of the plant manager the successful conveyors are those he never hears about. They continue to economically transport the loads applied to them, requiring only routine maintenance attention. When such conveyors are subjected to closer scrutiny you will find that they have been carefully selected and engineered to perform the required function under the anticipated conditions. Among the primary elements in a conveyor drive are the electrical motor and the speed reducer. The selection of these elements can be aided by the systematic consideration of several factors. These factors which focus attention on the critical operating conditions, will be individually evaluated and their effect upon the selection of the electrical drive system and speed reducer analyzed.

Jan 1, 1958

By W. E. Lytle

Environmental permitting is a critical component for joint-venture projects located in the Commonwealth of Independent States (CIS). This paper presents the basic CIS regulatory environmental requirements for permitting of a hypothetical mining source and emphasizes air permitting. Topics which will be covered include: the Expertiza process, air pollution quantification, data requirements, and air pollution modeling protocol. A comparison will be made between permitting requirements for air pollution sources in the United States and a CIS country, Kazakstan.

Jan 1, 1998

By Charles R. Nelson

INTRODUCTION The support of openings in weak sandstones can be achieved by spraying on a liquid grout which will soak in and harden to form a shell. In the St. Peter sandstone of the Minneapolis-St. Paul area of Minnesota compressive strength is increased from about 0.7 MPa (100 psi) to over 7 MPa (1000 psi) to depths of 152 mm (6 in.). A shell of this strength and thickness can pro¬vide support much as shotcrete does but at lower cost. If the spray-grouted shell is inadequate for the support needed, it provides a good base for shotcrete application, which is often difficult in weak or friable sand¬stones because the fresh shotcrete peels off along with a thin layer of sandstone. The spray-grouted technique was initially developed at the Civil and Mineral Engineering Dept. of the University of Minnesota using funds provided by RANN Div. of the National Science Foundation. It was used as temporary support in a 3-m (10-ft) wide, 3700-m (12,000-ft) long storm water drain tunnel by the Minneapolis Sewer Construction Dept. Much of the field development at this construction project was carried out with the cooperation of the personnel of the city of Minneapolis. It also was used for temporary support in a 3.3-m (11-ft) wide, 1800-m (6000-ft) long storm water tunnel built in 1978-1980 for the Minnesota Dept. of Transportation in Minneapolis. In 1975, 2000 m (6500 ft) of 1.5-m (5-ft) wide utility tunnels were spray-grouted for final lining. A 50-m (150-ft) long, 1.2-m (4-ft) wide test tunnel built at the university in 1974 was sprayed for half its length and is being observed for long-term behavior which to date (1981) is good. GROUT MATERIALS The requirements for the liquid grout are more severe than those for injection grouting. Besides being able to penetrate the rock and develop sufficient strength, it must have the following properties: (1) be nontoxic, noncombustible, and have a low odor for spraying under¬ground; (2) have controllable viscosity and setting time for adjusting to the permeability of the sandstone and the required depth of penetration; and (3) must "wet" the sandstone and develop capillary "draw" to penetrate to the required depth. A sodium silicate-based grout with the proper setting agent meets these requirements in the local St. Peter sandstone which has a uniform grain size dis¬tribution curve with D,,, = 0.1 mm, permeability of about 10 to 20 darcys, a porosity of about 25%, and less than 5% of silt size or smaller. It is 97 to 99% pure SiO2. The grout mix consists of Philadelphia Quartz Co. Type N sodium silicate and Celtite 55 Terraset Spray Grade (SG) distributed by Celtite Inc., Cleveland, OH. A volume mix ratio of 100:9:125 for sodium silicate to setting agent to water produces a grout with two to four centipoise viscosity, and initial set at 20°C of 20 min. Setting time is temperature dependent, being longer at lower temperatures, but can be adjusted by varying the setting agent concentration a few percentage points. APPLICATION The application is simple. Spray the grout on the surface until the desired penetration is achieved. Penetration rates of about 5 mm (0.2 in.) per min. are realized in the St. Peter sandstone for up to 152 mm (6 in.) of penetration (30 min. of spraying). The set time must be longer than the spraying time. The spray nozzle should be moved back and forth at a rate that minimizes runoff due to surface buildup. Both a single large hand-propelled nozzle and multiple small machine propelled nozzles have been used successfully. The pumping and mixing equipment used consisted of: (1) a hand-held, hand-pumped, 11-L (3-gal) gar¬den sprayer for test patches (mix by shaking); (2) 76-L (20 gal) batch mixing in barrels with small electric pumps for spraying and mixing; (3) two component pumps consisting of Hypro Model 5300 piston pumps (Hypro Pump Co., St. Paul, MN) on a common shaft driven by an electric motor. The sodium silicate is premixed with a portion of the water and the setting agent is mixed with the rest of the water. The two components are combined and mixed just before the nozzle; and (4) a proportioner metering the setting agent just before the nozzle with the water and sodium silicate premixed and pumped from the surface. The proportioner permits the bulk of the grout to be pumped through a single pipe or hose with only the setting agent stored underground. This is efficient and low in cost. COST The grout mix costs about $0.20/L ($0.75 per gal) in 1978 dollars. Filling all the voids 100 mm (4 in.) deep (25% initial porosity) would have a materials cost of about $5.40/m2 ($0.50 per sq ft). The labor cost of application is usually less than the material cost for normal tunnel jobs. A pump and proportioner cost less than $1000. Sodium silicate storage tanks and pip¬ing costs would depend on the particular site conditions. REFERENCES AND BIBLIOGRAPHY Nelson, C. R., 1977, "Spray Grouting for Tunnel Support and Lining," Underground Space, Vol. 1, No. 3, pp. 241¬ 245. Yardley, D. H., Nelson, C. R., Stocker, T. H., 1974, "So¬dium Silicate Spray Impregnation of Tunnels in the St. Peter Sandstone," Research Report, University of Min¬nesota, 118 pp.

Jan 1, 1982

By T. Klemetti, W. H. Su, M. A. Van Dyke

Entry stability in coal mines is dependent on geologic conditions and engineering controls. Most engineering controls in ground control are predictable and standardized for typical geologic conditions. However, geologic anomalies may exist that are difficult to detect with traditional core hole drilling. Borescopes offer a cost-efficient way to gather more geologic data between core holes. Additional data obtained from borescope results provide a clearer picture to enhance detection of hazardous conditions due to geologic anomalies. The equipment, methods, and analysis of borescope results provide geomechanical engineers with a clear understanding of strata behavior and the best information to implement roof control plans and supplemental support to enhance miner safety and health. INTRODUCTION Borescope technology has changed very little since its inception. However, the idea to use borescopes to examine roof strata started with the U.S. Bureau of Mines in 1979 with the production of a fiber-optic borescope (FitzSimmons, et al., 1979). The first documented use of a borescope in the coal mining industry began during the 1980s in Australia by researcher John Shepherd. Shepherd’s idea was to use a borescope to collect a series of data points from the roof lithology and compose a geologic cross section. The cross section was then used to identify key features that suggested the beginnings of roof failure. The features Shepherd identified were bedding plane separations in the roof and low angle, extension, and tensile failures. Shepherd also suggested that the borescope findings could be used for geologic mapping for lithological variation, fracture distribution, and determining if supplemental roof support was needed (Shepherd, et al., 1986). In the United States the first publication about borescope usage for coal mine stability assessment was by Su and associates in 1999, who specifically related the combination of using borescope, geophysical, and corehole data to produce geologic hazard maps (Su et al., 1999). This work directly linked the usage of a borescope with the design of supplemental roof support. The use of borescopes in mining was adopted industry wide by the 2000s. Operator case studies were being published using borescopes to aid in supplemental support recommendations and hazard mapping. An Australian study published in 2007 based the optimization of secondary support after each longwall pass on the results of borescope data. The study stated that the borescope was an invaluable tool for understanding roof behavior (Black, et al., 2007). In 2009, a publication by the National Institute for Occupational Safety and Health (NIOSH) took the concept of borescoping one step further. The work centered around creating a roof quality index (RQI) for limestone mines based on borescope data. The RQI attempted to assign a ranking to establish the nature of the roof and its stability (Ellenberger 2009). In theory, this would have been a very useful tool, but the RQI system has not been widely adopted in the industry.

Jan 1, 2019

By A. K. Smith

Overexposure to noise remains a widespread, serious health hazard in the U.S. mining industry. Most other categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. U.S. Mine Safety and Health Administration (MSHA) coal noise data from 2000-2004 show that the continuous mining machine (CMM) is first among all equipment, accounting for 35% of noise overexposures. Joy Mining Machinery, in collaboration with the National Institute for Occupational Safety and Health (NIOSH), is conducting research to reduce noise generated by continuous mining machines. This paper describes a "JOY Designed for Noise Reduction" (JOY DNR; patent pending) tail section as a noise control for reducing the noise overexposures of CMM operators. Underground testing shows a 45% to 65% noise exposure reduction for the operator when comparing the JOY DNR tail section results to those for a standard machine. Utilizing this newly developed noise control, along with previously proven controls, will provide CMM operators an opportunity to be within the MSHA permissible exposure limit (MSHA-PEL). Mining Engineering, 2011, Vol. 63, No. 7, pp. 83-85. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

Rest potential, cyclic voltammetry and chronoamperometry measurements were made to study the effects of cathodic polarization of chalcopyrite simulating the mineral contacted with grinding media under a nitrogen atmosphere. The reaction products on the chalcopyrite surface were identified by XPS and the mechanism of the cathodic reaction was proposed. Micro-flotation tests were performed to investigate the effects of surface changes on the floatability of chalcopyrite.

Jan 1, 1991