Search Documents

By Lawrence P. Kennedy

The Lynne deposit is a volcanic-to volcaniclastic-hosted, Zn-Pb-Cu-Ag orebody located in the early Proterozoic magmatic terrain of northern Wisconsin. As of February 1991, core drilling has partially delineated a multi-million ton, near-surface, disseminated to massive sulfide deposit. The deposit is hosted by a gently dipping sequence of fragmental rhyolites, felsic tuffs, less abundant dacite to andesite flows, and fine-grained volcanic sediments. The deposit is broadly conformable With the host rock stratigraphy, but the ore zones thicken and coalesce in the central part of the deposit.

Jan 1, 1991

By C. A. Rawlins, P. Rostami

"Ventilation systems are not only an integral part of any underground mine design but are a significant contributor to the mine’s capital and operating costs. The ventilation and cooling design systems presented in this paper were part of the prefeasibility evaluation of an underground platinum mine in South Africa. The mine would ultimately operate at the depth of 1,200 m below surface with a proposed 4 Mtpa production rate. The proposed mining operation is a highly mechanized operation using diesel equipment. Significant daily production rate, large amount of equipment and expansive nature of the operation, contributed to a challenging while flexible ventilation design requirements. This paper presents how to safely and efficiently optimize capital expenditure and operating costs associated with the mine air cooling and refrigeration system through practical ventilation design practices. Successful capital and operational savings by modulating installation and commissioning of refrigeration facilities can influence the economic realization of such systems. The adapted planning and design approach provided a cost-effective advantage while complying with design safety and regulations. INTRODUCTION This paper outlines a prefeasibility evaluation of the heat loads and related cooling system to be employed at the proposed platinum mine. The paper also provides appropriate details for a comprehensive understanding of the applied methodology. The proposed mine will be a trackless underground operation using a combination of mining methods. Initially, ore zones with vertical thicknesses greater than or equal to 18 m will be mined using the long-hole stoping (LHS) method, while thinner ore zones will be mined using mechanized drift-and-fill or drift-and-bench methods; hence, a highly mechanized operation with LHDs, trucks, drill rigs, personnel carriers, etc. is envisioned. Broken rock (ore and waste) will be transported by the means of trucks to the main passes (ore and waste) and collection points. Mining zones identified in the project occur at depths ranging between approximately 700 m to 1,600 m below surface. Primary access to the mine will be via a 1,100 m deep, 10 m diameter production shaft (named Shaft No. 2), three additional shafts will be sunk to provide future ventilation and production support. Three main access levels are established as primary haulage levels and include a series of interconnecting ramps. Additional mining sublevels will be developed as necessary. Figure 1 shows the proposed shaft locations and main access levels in a 3-D elevated view. Mining is performed using highly productive mechanized methods. For this reason, an annual ventilation estimate is based on requirements for mobile equipment (i.e., 0.06 m3/s/kW). The air requirements imposed on the underground operation is further influenced by equipment heat loads, auto compression, and virgin rock temperature, as the main sources of in-mine heat."

Jan 1, 2015

By G. Castillo, J. Mortensen

"INTRODUCTION Molybdenite is typically produced as a co-product in the copper ore flotation process. At the Rio Tinto Kennecott Concentrator (RTKC) in Copperton, Utah, the molybdenite is initially floated with copper sulfides and other value minerals producing a Cu-Mo concentrate. This is then separated in the molybdenum plant by depressing copper sulfides and pyrite and floating only molybdenite. The molybdenum plant in RTKC comprises the rougher circuit and several stages of cleaning to achieve a certain grade requirement of Mo. The rougher circuit is where the first stage of separation occurs. Cu sulfides and pyrite are depressed in the rougher circuit by adding NaSH under nitrogen and in the cleaner circuit by adding NaSH under air. The depression of Cu sulfides (and pyrite) by NaSH is related to the redox activity1. It is important therefore to maintain a reducing potential in the circuit in order to achieve effective Cu-Mo separation. If the rougher circuit is under air, like RTKC’s molybdenum cleaner circuits, it is harder to maintain the target redox potential because NaSH oxidizes rapidly in the presence of air thereby increasing NaSH consumption significantly. CU-MO SEPARATION AND ROLE OF PULP POTENTIAL The collector adsorption on copper sulfide minerals is through an electrochemical mechanism2. The collector changes the surface chemistry of the Cu mineral allowing it to float. Molybdenite, or MoS2, on the other hand, floats readily in the presence of a frother as it is naturally hydrophobic. Usually, hydrocarbon oil extenders such as diesel or burner oil are added to enhance Mo recovery. In order to effectively separate Cu from Mo, the collector complex on the copper surface needs to be destabilized or desorbed using a reducing agent such as NaSH or Nokes. As long as the circuit is under highly reducing conditions, the collector remains detached from the sulfide mineral surface allowing Cu sulfide depression. Therefore, it is important to measure the oxidation-reduction potential (ORP) continually and maintain the reducing condition with addition of NaSH. For a given collector each mineral will have a characteristic potential or electrochemical window for flotation to occur3, therefore, it is necessary to reduce the potential outside of this window in order to effectively separate Cu and Fe sulfides from MoS2 minerals2. In RTKC plant, the target reducing condition is between -450 to -550 mV to effectively destabilize the collector and depress Cu and Fe minerals. Typically the dosage of NaSH used in the molybdenum plant could range from 6 to 30 gallons/min (gpm). The high dosage of NaSH could pose risk of H2S exposure. RTKC wanted to evaluate alternatives to NaSH in order to reduce its consumption and minimize risk of H2S gas generation."

Jan 1, 2016

By Gordon Clark, Basar Arioglu, Zlatanic. Sanja, Nasri Munfah, Togan. Tolga

"The 13.2 m external diameter double deck Istanbul Strait Road Tube Crossing is one of the most challenging underwater tunnel projects in the world. Subjected to 11 bars of hydrostatic pressure, variable geology, and being in a very active seismic area, the execution of the project required innovative solutions, sophisticated construction techniques, and prudent risk management approach. The 5 km tunnel consists of 3.4 km TBM bored tunnel, 1 km twin NATM tunnels, and cut and cover sections. The project is being delivered in a Build-Operate-Transfer (BOT) contract in a public-private partnership. The technical challenges, coupled with financial and commercial risks required the implementation of sophisticated risk management tactics including the provision of Independent Design Verification. Presently, the project is in its advanced stages of construction with a recent successful TBM breakthrough on August 22nd 2015. The paper presents the technical challenges of the project from the design, construction, and risk management aspects and provides the status of the construction. PROJECT BACKGROUND The $1.245 billion Istanbul Strait Road Tunnel Crossing project, dubbed the Eurasia Tunnel, is one of several major infrastructure projects being implemented in the Republic of Turkey in a public-private partnership approach. The project provides a direct and easy connection between the Anatolian (Asian) side of Istanbul and the heart of its historical district on the European side across the Bosphorus Strait which connects the Black Sea with the Sea of Marmara. Upon its completion in 2017, the project will improve connections to a wide network of motorways on both sides, increase capacity across the Bosphorus by 100,000 vehicles a day, reduce congestion and save motorists an average of 45 minutes of commuting time in each direction, and bringing significant economic benefits to the city and the region; it will ease traffic across the strait, reduce congestion, decrease pollutants and emission while maintaining the historical silhouette of the city. Figure 1 provides a general view of the project location and alignment. The overall project consists of three parts totaling 14.6km. Parts 1 and 3 consist mainly of widening existing motorways, providing connections to existing roads, reconstructing local bridges and underpasses on the European and Anatolian sides respectively. Part 2 is the tunnel crossing across the Bosphorus; it is the most complex part of the project with the greatest challenges and risks. Part 2 is 5.4 km long consisting of 3.4 km of 13.2m external diameter TBM bored tunnel under the Bosphorus Strait, 1-km of twin NATM tunnels on the Asian side, cut and cover transition boxes in the Asian and the European sides and depressed approaches on both sides. In addition, this segment includes the toll plazas, ventilation buildings, and the tunnel control and maintenance facilities."

Jan 1, 2016

By Steve Kral

"Each January, tunneling and underground professionals gather in New York City for the George A. Fox Conference. The one-day event offers attendees the opportunity to listen to their peers outline what’s new in the underground construction industry, get updates on major projects in North America and have a chance to catch up of old friends.The conference is put on by the Underground Construction Association of SME. This latest conference attracted about 370 specialists in the industry. The theme for this year’s event was “Water Tunnels, Past, Present and Future.”The technical session included talks focused on major tunneling projects, including the massive California Water Fix program and the Massachusetts Water Resources Authority (MWRA) Metropolitan tunnel redundance program in Boston. The conference also included an update on the Gateway Project from Phil Rice from WSP and Mahammed Nasim of Amtrak as well as a Tunnel Industry update.The following is a sample of a few of the presentations. Technical presentationsDEP’s Tunneling Program Evolution. James Mueller is the agency chief engineer of New York City’s Department of Environmental Protection (DEP). Its mission is to plan sustainable infrastructure investments for the future of clean water and the environment in the city and its watersheds, he said. The agency’s goals are to synthesize information across bureaus within DEP to allow data-driven decision-making. It is also to optimize internal agency processes and systems related to the implmenation of engineering programs within a structured assessment process. The agency also prioritizes projects and funding within a structured integrated planning process. And it standardizes project performance and delivery to meet the needs of the agency in alignment with industry standards and market capabilities."

Mar 1, 2019

By Wilbur J. Morin

Construction of Flaming Gorge Dam in northeastern Utah necessitated the construction of a new state highway, Utah-260, to provide access to the dam and the town of Dutch John. A 550-foot arch structure was designed to span Cart Creek, about one mile southwest of the dam. The rock exposed at the site is highly fractured quartzitic sandstone with interbedded shale of the Precambrian Uinta Mountain Group. Eight exploratory holes were drilled, four in each abutment area, to determine rock types, the extent of fracturing at depth and rock strength. Drill cores in the west abutment revealed blocks of quartzitic sandstone loosened by the weathering and partial removal of underlying shale beds. The rock in the east abutment area was found to be highly fractured to depths of 70 feet and as far east as 50 feet from the footing locations. Selected core sections were tested for unconfined compressive strength but the values were not considered-representative of the in-situ fractured rock. To prevent movement along or, perpendicular to open fractures, four drilled-in columns were provided at the base of each footing. These extended 50, feet beyond the base of the footing, along the bearing and inclination of the thrust reaction.

Jan 1, 1963

By Samara Ali-Ahmad, Keith Hanks, Cindy Pham

The City of Los Angeles will rehabilitate approximately 9 miles of its North Outfall Sewer. This sewer was constructed in the 1920s as an unreinforced concrete semi-elliptical sewer. One of the methods for rehabilitation is to approach the sewer as a pre-excavated tunnel and install pre-cast segmental liners to provide a single pass corrosion resistant, structurally self sufficient project. The estimated cost for this project is $46 million. The project has completed the pre-design study, and the design is now underway.

Jan 1, 2003

By L. Hagenbuch

Off-highway truck purchasers know the amount of tonnes, pounds, kilograms, etc, a truck will carry. However just because a truck is rated at 240 tons may in no way correlate to what that truck will actually carry. Two numbers define the carrying capacity of an off-highway truck: 1. The weight carrying capacity of the truck; 2. The volume carrying capacity of the truck. These two numbers must be in sync or the amount of payload carried will vary from the carrying capacity of the truck. Currently the Society of Automotive Engineers (SAE) standard J1363 January 1985 defines the volumetric carrying capacity of an off-highway truck. However as is well known in several South American countries, the SAE standard overrates the truck’s effective volumetric carrying capacity 15% to 20%. This paper presents a method for measuring “effective” body volumetric carrying capacity, resulting in a truck body for carrying the targeted load, matched to the loading equipment that interacts positively with the truck chassis.

Jan 1, 2002

Surface characterization techniques, i.e. contact angle measurement, atomic force microscopy (AFM) surface force and surface imaging measurement, were applied to investigate the molybdenite surface in aqueous solution. It was shown that the cleaved basal surface of molybdenite was very hydrophobic with a 92 degree water contact angle. The non-polar component of the solid surface free energy is 50.52 mJ/m2 while the polar components are almost zero. The solid surface was not reactive and was only weakly charged at the pH 6. When the aqueous media changes from water to 1×10-4 M KEX solution, the measured contact angle, adhesion force and surface roughness all increase slightly. However, ethanol rinsing made the surface change back to the bare substrate. It was suggested that the hydrophobic chemical, i.e. dixanthogen, which was shown in the morphology of patches by the AFM image, physically adsorbed on the hydrophobic molybdenite surface through the hydrophobic interaction.

Jan 1, 2009

By P. S. Parobeck, T. F. Tomb, R. S. Ondry

From October 1980 through August 1982, surveys were conducted on 19 longwall mining operations to obtain data relative to respirable dust levels associated with particular longwall operations and occupations, to make recommendations for enhancing dust control, and, where applicable, to evaluate the effectiveness of new technology implemented to control dust. The paper summarizes the data collected during these surveys and, where possible, draws conclusions and discusses actions that can be utilized to reduce exposures to respirable coal mine dust on longwall mining operations.

Jan 1, 1987

By Henry E. Reed

This presentation is about a small company, Industrial Mineral Products, that was formed in 1972 with one product and one customer and by a series of value-added changes avoided disaster and increased sales many times over. The principal of the company stopped by my office in Seattle looking for industrial mineral opportunities in the Northwest. We got together and went through all the minerals in Ladoo's "Industrial Minerals" from Abrasives to Zircon to see if we could find something available on the vast holdings of the Burlington Northern. At that time one of our lessees was operating a silica sand mine near Ravensdale, Washington and indicated that he might be interested in selling out. This sounded interesting to my client and within two weeks the transaction was completed.

Jan 1, 1990

By Richard Ladyman, Ken Baxter, G. B. Siddall

The IPS process, developed by Baxter and McAuley, was first applied in Australia in 1984 at Browns Creek in NSW where a small 300kg batch plant was in operation for a number of years. To date a further 14 plants have been installed. While a number of engineering companies have engineered applications of the technology, a majority of the plants constructed to date have been constructed by Como Engineers who have a reference list of 9 installations with batch capacities up to 3.0 t.

Jan 1, 1996

By P. R. Hervey

Quartz is the second most widely used electronic material, with approximately 3,000 tons of single crystals used each year. Virtually all of this material is synthetic; grown with a technique called hydrothermal growth. We will review the basics of hydrothermal growth, the feedstocks for these crystals, and the challenges to improving the growth process. We will also review the processing of these crystals, the markets and applications where they are used, and the global outlook for these markets.

Jan 1, 1999

By Ray Nivens, Umit Turunc, Caroline Sui, Nick Morrison, Douglas Steiner

"In most copper mines and concentrators, mill water is continuously recovered and reused, with fresh water added to make up for losses. When mixed, these water chemistries can lead to severe scaling, especially in pipes, tanks and pumps on the mill water supply side, reducing flows and causing significant production losses.At KGHM Robinson Nevada Mining Company, increases in the fresh water addition ratios resulted in severe scaling problems and premature pump failures thereby jeopardizing plant production. What initially appeared to be a few isolated scaling events eventually unfolded into a recurring pattern of water supply-related production losses with increasing severity. Through completion of detailed root cause analysis, chemistry modeling, laboratory work, in-plant testing and system engineering, the mechanisms of scaling were identified and addressed.Advancements in fresh water addition practices and antiscalant application methods resulted in a stepwise reduction of the mill water scaling. Cost savings and production benefits were significant to the plant’s financial metrics.IntroductionThe production of mineral and metal concentrates using the flotation process requires large quantities of water. Flotation is utilized as the primary means for beneficiation with sulfide ores. Mined ores are crushed and ground into a slurry of 20-55% solids. For each ton of ore, 400-900 gallons of water1 are needed to supply the grinding mill. Additional water is needed in the flotation circuit as well. With many modern mills operating at2 11,000-165,000 tons/day, water supply volumes can be upwards of 3,000 gpm to 100,000 gpm of flow.For plants operating at or above capacity, disruptions and restrictions in water supply flow can have a direct impact on the production and recovery of the metal. Water supply flow can be limited for a wide variety of reasons but of interest are those limitations that are due to mineral scaling. Mineral scaling is the selective point precipitation of inorganic species above saturation concentrations. Precipitated species form flow-restricting deposits in the mill water system (tanks, pumps, pipe and valves), that will eventually impact water supply to the concentrator."

Jan 1, 2017

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

6.1 PRINCIPLES OF PLANNING GROUTING OPERATIONS FOR SHAFTS, DRIFTS AND TUNNELS The planning of integrated grouting of vertical, inclined or horizontal underground workings in saturated, fractured rock includes the following phases: 1. Planning for the collection and analysis of geological information concerning the characteristics of the struc¬tural deformation(s) that produced the details of the frac¬ture system being studied. 2. Planning for the acquisition of initial hydrogeological information produced by the flowmetric and hydrody¬namic investigations (described in Chapters 2 and 3). 3. Computing the initial engineering calculations of the ex¬pected or planned dimensions of the isolation curtains for each water-producing stratum (fracture zone) and the expected areal spreading pattern of the grout in each of these water-producing horizons. The selection of the lo¬cations, the initial optimal number of holes and the vol¬ume of grout needed to create each isolation curtain also are included in this phase. 4. The selection or development of a grout formula for the specific hydrogeological conditions that exist at the site. 5. Identification of a resource (deposit) required to produce the grouting clay. The planning of grouting operations must be supported by the acquisition of all necessary initial data, which in¬cludes: 1. The geographic location and administrative responsibil¬ity (ownership and regulatory constraints) of the mineral deposit and any peculiar features of the area where ex¬cavation of the underground workings is planned. The surface relief, the hydrographic network of the region, and the local climatic conditions must be evaluated prior to planning for buildings and waste discharges if any. 2. The economic status of the region, the available trans¬portation, the nature of the energy base, the water and heat supply sources, the location of construction mate¬rials suitable for making the grout all must be deter¬mined. 3. The geological and hydrogeological characterization of the work site must be accomplished. 4. The technical features of the shaft(s) and underground works must be characterized. 5. The organization's principal initial design plan features and the construction sequence of all buildings and struc¬tures must be developed. These must be correlated with the organization and schedule for excavating the under¬ground works. The technical characterization of a shaft or of other un¬derground workings must contain information about the purpose of the workings, the design depth, the planned excavation procedures along with cross-sections, and the parameters of the lining, if a lining is required. The geology of the section to be penetrated must include geological data obtained from existing exploration activities at the mineral deposit and conclusions about the shaft ex¬cavation conditions obtained from drilling technical moni¬toring holes and exploration drillholes. The interpreted stratigraphic regime, including the thickness, strike and dip of each stratum, must be shown in cross-section. The tec¬tonics, including all geologic structures, must be presented by cross-sections. The bedding orientations must be used to identify anticlines, synclines, monoclines and faults. The lithologic composition and the drillability of the rock com¬prising the section must be examined. The character of the rock's fracture pattern must be presented. Finally the per¬meability, porosity and storage characteristics of each aqui¬fer must be determined by in situ hydraulic property testing (injection tests or pumping tests, as described in Chapter 3). The fracture pattern of the indurated rock is presented in reports derived from geo-exploration borehole studies and from studies of outcrops on the surface and in all nearby underground workings. The extent of each fracture zone is mapped in three dimensions. The distribution of fracture apertures, the nature of the fractures according to each litho¬logic stratum, and the relationship of bedding planes to each fracture system are all determined. Acoustic logs, downhole cameras, caliper logs, oriented core, and any other appro¬priate geophysical tools available are used to construct the data base for this purpose. The hydrogeological characterization of the geologic section to be penetrated by the workings is based on the analysis of hydrogeological data collected during the drill¬ing and testing of technical monitoring holes and from in¬formation on ground water inflow collected during the ex¬cavation of nearby underground workings, if such workings exist. The hydrogeologic characterization must contain the following information: 1. The identification of all aquifers, their thicknesses and their locations in the section, 2. The distribution of hydrostatic head in the ground water in three dimensions, 3. The coefficient of saturated hydraulic conductivity (per¬ meability) of each aquifer, 4. The porosity and storativity of each aquifer, and 5. The projected rate of water inflow into the shaft, drift or tunnel for each aquifer prior to grouting. This step is used to identify the zones to be grouted.

Jan 1, 1993

By Patrick J. Doig

The NS9 Drop Shaft contract formed part of the Waste Pollution Abatement Program (WPAP) conducted by the Milwaukee Metropolitan Sewerage District (MMSD). The contract involved the construction of two shafts, a deaeration chamber and connecting tunnel, and ancillary facilities. Portions of the construction were located in saturated overburden where dewatering was prohibited. Ground freezing was utilized for temporary support of the excavation. This paper concentrates on the freezing system and the excavation of frozen ground, with particular emphasis on the use of mechanical cutting equipment, including a raiseborer and a roadheader.

Jan 1, 1991

By Gy. Deák Deák

The ECOMINING platform aims to develop a scientific and technical organization in order to promote within the natural resources industry a framework for environment-friendly exploitation technologies (on Best Available Technologies principle) and also to develop a solid basis for performing Research and Development projects. The ground of this project is the success of the First International Seminar: ECOMIN-ING - Europe in 21st Century1, organized by the Research and Development National Institute for Metals and Radioactive Resources Bucharest in co-operation with ITASCA Consultants GmbH Germany, the University of Petrosani and supported by the National Society of Salt Bucharest & Praid salt mine branch and the Ministry of Economy and Commerce. The platform provides a complex data base, for partners? selection and researchers? team structure. This can provide the scientific results with a high level of confidence for the projects of interest in the field of exploitation of mineral resources and for the participation on national and international project proposals competitions (i.e., target the 7th Framework Programme or any European / national programme, which can provide funds for the ECOMINING platform field of interest). The next step is the affiliation of the ECOMINING platform to the European ones, and to be compatible with them. The ECOMINING platform represents itself a 7th Framework Programme (FP) project idea.

Jan 1, 2007

By Stanley W. Ivosevic, Mark E. Emerson

Introduction Metals exploration activity is moderately intense in the US despite the 1981-82 recession in the mining industry. Although exploration expenditures are significantly less than the 1981 peak, quality and goal orientation of current exploration are high. Major foreign and domestic mining companies as well as nonmetal companies had been attracted to invest in minerals in the US. Its capital markets, political stability, and open-door policy are attractive for hard mineral explo¬ration, particularly in the West. The approach was to either acquire fully or partially developed ore bodies through merger and acquisition, or to fund large scale exploration programs in search of bulk-tonnage deposits. The acquisition avenue has not proved the panacea envisioned for overcoming lack of substantive mineral development. Nor has the decentralized approach to exploration that was adopted proven cost-effective. The emphasis on gold, to the exclusion of all other commodities, raises questions regarding the direction of exploration in the US for the rest of the 1980s. Overview More than 300 companies are active in metals exploration in the US. These range from established, well-known domestic and foreign corporations to hurriedly incorporated, unknown companies financed by having promoted mineral prospects or occurrences of questionable quality. Junior companies tend to be oriented toward property entrepreneurship, rather than the development of minerals resources. These companies have helped maintain mineral lands from prospect to production by holding blocks of property intact during periods of exploration inactivity. This was done through promotional efforts, even though few properties that attracted major venturers proved to have real merit. Exploration objectives of senior and junior exploration companies currently embrace only a few commodities. Arranged in approximate descending order of priority, these are: precious metals; base metals in monometallic or polymetallic deposits; strategic metals, such as tungsten, tantalum, and tin; unconventional commodities, such as diamonds; ferrous metals; and commodities such as beryl, zeolites, and barite. Prospectors are important in searching for these targets. In the US, where they have been financed by major and junior companies, prospectors have proven a useful and low-cost means of locating gold prospects (e.g. the Alligator Ridge property in Nevada). The tenacity and persistence of independent prospectors have been factors in discovering properties rejected or overlooked by professional geologists (e.g. Lornex mine in British Columbia). This has been realized by the provincial government that grubstakes bona fide prospectors. Exploration interest in commodities has always been cyclic with price. Gold is one of the few metals that has experienced a price increase of such magnitude to warrant attention. The potential for realizing adequate operating margins for the Nevada open-pit "no-see-um" gold deposits is great. The present declining gold price, however, may indicate that this emphasis on gold, to the exclusion of other commodities, is shortsighted. Mining companies have been the last to react to price increases, opening new mines based on unrealistic market expectations. A scenario could develop where plummeting gold prices bring recession to the gold industry, as lately occurred in uranium, molybdenum, and copper. US Exploration Climate The US is attractive for exploration due to its strong mineral po-

Jan 4, 1984

By Paul Lenchuk

The concrete block industry can trace its beginnings to the early 18th century when most of the experimental work was being carried out in England. In America, the concrete masonry industry got started shortly after the Civil War and has had sometimes a spectacular, but always a steady growth since then. From a few hundred thousand concrete masonry units made in the late 19th century, the industry today produces approximately 3.3 billion concrete masonry units making it the largest industry in the United States for masonry wall materials. There were 3500 concrete masonry plants manufacturing these units after World War II. This nwnber decreased to 1500 by 1970 although the production of concrete masonry units increased by over 100% in the last 25 years. One of the reasons for this increase in production by less than half of the plants which once existed, is the tremendous strides made in automation of production machinery. The concrete masonry plant of today is probably one of the most automated small businesses in existence. Within a few years it will be possible to push a button and the entire manufacturing process will begin with no human hands touching the units until they are laid up in a wall at the manufacturing plant and are trans-ported to the job site. No other concrete product has reached this state of manufacturing sophistication and it is one of the reasons why the price of a concrete masonry unit is not much different than it was 2S years ago. Because of automation, it is safe to say that concrete masonry will remain a highly competitive building material for many years to come. The problems that beset the continued use of this material are not related to the cost of manufacturing and delivering the product. What are some of the problems as well as some of the opportunities and is the golden age of opportunity knocking rather than a wolf in disguise? The use of concrete masonry has grown each year because a larger unit was provided at less cost than other competitive materials. Concrete masonry has had severe competition from the clay products industry as well as masons who laid the product in the wall and who resisted concrete masonry for many years. Even today

Jan 1, 1971

By B. M. Eiter, J. Hrica, D. R. Willmer

"Mineworkers are routinely tasked with making critically important decisions about whether or not a hazard presents an imminent danger. Researchers from the National Institute for Occupational Safety and Health (NIOSH) collected formative data to investigate mine safety professional perspectives on workplace examinations, which revealed a potential gap in how mineworkers are assessing risk. During interviews, participants indicated having processes in place for what should be done once an imminent danger situation is identified. Critically, however, they report having no systematic methodology for mineworkers to use to determine if a hazard is considered imminent danger. While this is important for all imminent danger situations (e.g., failure to lockout/tagout), it is especially important for those situations that are not immediately recognizable as imminent danger. In this paper, we identify and describe, three distinct categories of imminent danger complexity and discuss potential steps that could lead to improved identification of imminent danger situations. Finally, we identify potential practices to incorporate into risk management efforts, including feedback, communication, and specialized training to increase awareness of imminent danger situations. INTRODUCTION In recent years, the metal and nonmetal (M/NM) mining sector, as categorized by MSHA, experienced an increase in the number of fatalities occurring at mine sites. From 2013 to 2015, 69 mineworkers were fatally injured; that is twice the number of fatalities that occurred in each of the previous two years (MSHA, 2015a). As a way to address this increase, the Mine Safety and Health Administration (MSHA) issued a program policy letter (P15-IV-01) suggesting that “miners would benefit from rigorous workplace examinations conducted by experienced and trained examiners (MSHA 2015b).” The goal of workplace examinations is to find hazards in the field and mitigate them before they cause injury or death to mineworkers. While it is important to identify all hazards in the workplace, it is critically important to identify those hazards that are considered imminent danger because they require an immediate response to avoid a severe or even fatal injury."

Jan 1, 2018