Search Documents

By W. W. Wen

Approximately 3 percent of the raw coal processed in U. S. Steel coal-preparation plants ultimately reports to slurry- tailing disposal. The usual disposal method is to pump the refuse slurry containing the minus-48 mesh (300 µm) refuse into dams or impoundments that are constructed of the coarse refuse. The failure of an impoundment at Buffalo Creek, Saunders, West Virginia and the sliding failure of a coarse refuse pile at Aberfan, Wales, England, resulted in an evaluation of refuse disposal methods by various regulatory agencies as well as coal producers. The result of this evaluation was the promulgation of Federal regulations dealing with the construction, operation, and final abandonment of coal refuse disposal areas. As a consequence of these regulations the use of the landfill/impoundment method of disposal became in some cases economically urlfeasible or technically impossible. U, S. Steel has studied a number of alternative methods of refuse disposal. During an investigation of mechanical dewatering with a pressure filter, Portland cement was added to the slurry to solidify the filter cake. Because of the success of the cement addition it was decided to study the stabilization of fine-coal-refuse slurry through use of cement-type additives.

Jan 1, 1979

By W. R. VanSlyke

Scrubbing is gaining increasing recognition as a valuable tool in the treatment of Mesabi Range intermediate iron ores. In general, the earliest washing plants included log-washers in their various flowsheets. While log-washers certainly did impart a degree of scrubbing to the crude ore, such treatment bears little resemblance to the type of scrubbing being practiced today. At the time that these early plants were erected, only the true wash-ores were being processd. ("Wash-ores" are defined as crude ores in which relatively coarse chunks of almost completely liberated iron are found in a matrix of loosely-consolidated fine sand.) To treat ores of this type, sizing at approximately 65 to 100 mesh was sufficient to produce a merchantable concentrate. As crudes were being treated in which there was little "locking" of iron and silica, log-washers tended to disappear and large screens and classifiers took their place in Mesabi range flowsheets. The "screening and classification" type of flowsheet 'had its greatest usage in the 1945-55 period, generally speaking. During this same period, many operators found it necessary to supplement the "wash-ore" type flowsheet with heavy-media treatment.

Jan 1, 1959

By Koji Nakanishi, Masayoshi Karasawa, Yasuhiro Morimoto

"Shin-Yokohama station (tentative name), one of the station of the Sotetsu - Tokyu through line (ST line), is under construction by the OPEN – CUT method. The Underground Soil–Cement Steel Diaphragm Wall is implemented as an earth retaining wall. This earth retaining wall is utilized as a main body of a subway station. It is the first time to utilize this earth retaining wall as the main body. There are two difficult issues for this project. One is that this station is planned under busy major road and there are many underground utilities, for example, an electrical transmission line. Because of that, construction area is limited. The other is that this station is located in a thick soft clay layer. This layer has a high risk of consolidation settlement because of draining during main excavation. Thus, high water tightness is required for this earth retaining wall. This paper reports design and construction methods for the Underground Soil–Cement Steel Diaphragm wall introduced as a part of the body of the subway station.1. OUTLINE OF SHIN-YOKOHAMA STATION 1-1. Location and structure of Shin-Yokohama Station Shin-Yokohama station is an intermediate station on the ST line connected to the Tokaido-Shinkansen bullet train, the JR-Yokohama line and the Yokohama Municipal Subway. Access to Tokyo and the Tokaido- Shinkansen from the eastern part of Yokohama city will be improved by this project. In addition, the number of estimated passengers of this station is one hundred thousand people/day because a soccer stadium (Nissan Stadium: 72,000 people), a huge indoor arena and a hotel are located in this area. This station consists of 4 stories and 3 spans (Max width; 29m, Depth; 33m, Length; 325.5m). Completion image is shown in Figure 2. Generally, stations have 1 platform and 2 trucks. But this station has 2 platforms and 3 tracks because some of ST line trains return at this station and a train deadheads from Hazawa station to this station in an emergency. This station is planned as 4 stories underground station, and the platform is on the lowest story. The reason why this station is in such a deeper position is to prevent the alignment from interfering with the Yokohama Municipal Subway station and foundation piles for bridge piers existing along the alignment. Even under the constraint conditions, earth covering should be shallow as much as possible. As a result, the tunnel edge is very close to the foundation pile, and the gap is only about 2m (Figure 3). In addition, passengers will be able to change trains easily from the ST line to the Yokohama Municipal Subway or vice versa at this station."

Jan 1, 2016

By Julian W. Feiss

Before undertaking to present to you a current analysis of copper, I would like to preface my remarks with a few observations that in themselves have a bearing upon commodity reviews in general. Having sat through a large number of such reviews since first joining the A. I. M. E. nearly forty years ago, I have no illusions about the hazards of the undertaking. If a speaker presents a statistical summary of commodity economics for the last year, most of his audience, having already read at least four commodity summaries on the identical subject, either get up and walk out or fall asleep. Should the latter happen, and were the listener to tumble from his chair and break his neck, obviously the speaker is liable. The subject matter seldom lends itself to histrionics on the part of the speaker so dangers of heart attack in the audience are not too great. Therefore the speaker, in order to retain listener interest, resorts to prophecy. Such venture was undertaken long ago by weather soothsayers, the "harouspex" of Ancient Rome, who generally cut up a sacrificial sheep and after staring at the entrails made their predictions which I understand had a batting average somewhat better than those undertaken on Wall Street based upon Dow Jones averages. Not being a licensed harouspex I cannot undertake predictions. I shall, however, fall back upon the experts.

Jan 1, 1965

By J. W. Merks

At mineral processing plants the accuracy and precision characteristics of assays in mill feed, tailings and concentrate largely determine the reliability of the metallurgical balance. The accuracy of measurements is ensured by selecting effective sampling methods and efficient sample preparation procedures, and by effecting each phase without introducing a systematic error while the precision of measurements is determined by the sampling regime. Sampling systems and components, sampling methods and regimes, and sample preparation procedures will be reviewed. Different techniques to determine variance components for sampling, preparation and analysis, and to detect systematic errors in assays at mineral processing plants, will be discussed.

Jan 1, 1986

By George M. Meisel

This paper is devoted to a discussion of the factors governing design of concentrators for large grinding circuits. Emphasis is placed on the manner in which use of ever larger grinding mills has affected the size of grinding bays, service cranes, gear reducers and electric motors, and the selection of ancillary equipment for cushioning of the starting load of large mills. Information is presented on the effect of using large grinding mills on the capital and operating costs of concentrators, e. g. : (Fig. 1) ? Benefits in lower cost of mills, drives and materials handling equipment, plant space, power, grinding media, operating labor and maintenance, and in ease of instrumentation and automation. ? Penalties in distribution of materials from the grinding mills to multiple lines of equipment which have not been developed to commensurately large sizes, and higher cost of ancillary equipment.

Jan 1, 1968

By M. J. Virnig, G. A. Kordosky

Throughout time, the mining industry has been very successful in meeting the world's requirements for metals and materials while meeting the challenges of decreasing ore grades and increased emphasis on protection of the environment. This success has been due to the development and implementation of new technologies. A clear example of such a development over the past 25 years is the increasing use of leaching/solvent extraction/electrowinning for the recovery of copper from oxide and sulfide ores. The key to the successful introduction of this technology was the discovery and development of the hydroxyoxime liquid ion exchange reagents by General Mills Chemicals (now Henkel Corporation). An important role was also played by the close working relationships between General Mills Chemicals and Ranchers Exploration which resulted in startup of the first plant in 1968 and between General Mills Chemicals and Bagdad Copper which resulted in the startup of the second copper SX-EW plant in August of 1970. Following on the heels of the hydroxyoxime development came the commercialization of other new chelating reagents based on different chemical functionalities, i.e., beta-diketones, alkylated 8- hydroxyquinolines and sulfonamidoquinolines. This initial spurt of activity was then followed by a slowing of development in terms of new reagent functionalities. Activity has continued in terms of further optimization/improvement of existing reagent functionalities but the commercialization of new reagent functionalities has slackened. This observation reflects the fact that the development of new reagent functionalities for metal recovery has become increasingly more expensive such that the right combination of price and sales volume must exist in order to justify the investment required to bring a new reagent to the market place. Given the dependence of the mining industry on innovation to meet the needs of the future, one can ask how these new developments, particularly in new reagents, will occur. To arrive at an estimate of the costs involved in commercializing a new metal extractant functionality, particularly a chelating type functionality, a case study of the development of LIX ®* 34

Jan 1, 1994

By T. Emery, D. Sweet, J. Bourgeois, M. Gomez, B. Seymour, J. Feiler

For traditional underhand cut-and-fill mining operations, it can be challenging to design a suitable cemented paste backfill (CPB) mix that can meet the necessary strength requirements and yet maintain its ductility. In deep underground metal mines, the CPB must achieve a high enough strength to be competent under high stress conditions while also remaining ductile enough to withstand high strain from squeezing ground as underhand mining continues under backfilled stopes. To eliminate ground falls that result in injuries and fatalities, researchers from the Spokane Mining Research Division (SMRD) of the National Institute for Occupational Safety and Health (NIOSH) have partnered with Aerix Industries, a producer of concrete additives, to study the effects of foaming agents on the strength and ductility of CPB. This laboratory study examines the impact of various amounts of foam additive on the strength and ductility of CPB mix designs, using binder and tailings provided by Hecla Limited from the Lucky Friday Mine

Mar 2, 2022

By Bjørn Nilsen

"INTRODUCTION/BACKGROUND Weakness zones or faults containing clay-rich gouge represent one of the most challenging rock mass conditions to be encountered during tunneling. In Norway, such conditions count for a large part of the rock support costs, and in cases where the rock support has been insufficient, serious instability and cave-in have in many cases been the result. Most commonly, such cave-in has occurred after water filling of hydropower tunnels, but in some cases it has also occurred in tunnels under excavation and in completed “dry” tunnels. To avoid instability, two important requirements have to be fulfilled: 1) The location of the weakness zone and its character have to be identified in time. 2) The rock support has to be sufficient to withstand the loading caused by the zone. An incident which really brought the problems related to swelling clay into focus was the cave-in at the Hanekleiv road tunnel in 2006. Here, rock fall from the roof as shown in Figure 1 occurred unexpectedly about 10 years after the tunnel was completed. Fortunately this happened at a time with very little traffic, and nobody was injured. This incident emphasized the significance of the issue of swelling clay, although it was found to be caused also by gravitational collapse of the clay-rich gouge material of the weakness zone, and not related to swelling only (Nilsen et al. 2007).In this paper, main focus will be on discussing the characteristic features of swelling clay, test procedures which are being used for characterizing swelling clay, and the reliability of the results from testing for use in support evaluation and design in conditions with swelling clay. It is generally well known that swelling clay may cause considerable pressure on support elements, but quantifying this pressure for reliable analysis and design of rock support is still a great challenge."

Jan 1, 2016

By William J. Lang

In just over a generation, the United States bentonite industry has grown from almost a rake and shovel operation into one with a multimillion ton annual production rate and exports to all corners of the globe. Bentonite production, pressed to keep pace with the soaring demand, has increased more than 10 fold in the last 30 years. The worldwide demand for bentonite is expected to double during the next eight to ten years. It remains to be seen whether U.S. producers will be able to maintain the dominant position in the world market. It should be noted that accurate statistical information regarding production or market information is difficult or impossible to obtain abroad and also within the United States. Published information obtained in response to questionnaires of the Bureau of Mines tends to be on the conservative side. FOUNDRY It has only been in the last thirty or forty years that bentonite has become an indispensible part of the age old metal casting industry. The relationship has proven most beneficial to both industries and promises to be long lasting. The foundry market for bentonite was the least of the three major markets twenty years ago but now leads all others and consumes 1/3 or more of the

Jan 1, 1971

By Richard Campbell, MEHMET KIZIL, Ismet Canbulat, Serkan Saydam

The design and effectiveness of ground consolidation to regain stability of longwall faces vary widely and are often based predominantly on-site precedence or what were considered successful applications at other sites in similar situations. Little is known regarding product migration characteristics or change in rockmass conditions as a result of the application of consolidation chemicals. This paper presents the in-situ testing rationale designed and implemented recently across several longwall operations in the Bowen Basin, Queensland, Australia to provide quantitative measurement of the actual zone of influence of various resin injection products. Product migra- tion was physically measured by monitoring the change in rockmass temperature as a result of the exothermic chemical reaction of the various strata consolidation chemicals used. In conjunction with strata coring and Lugeon transmissivity testing pre- and post-injection to characterise the improvement in rockmass conditions due to consolidation product injection. The results of the testing programme, migration measurements, and rockmass assessment are presented, along with a discussion on how site- based Rock Mechanics Engineers can incorporate the data into the design of strata consolidation plans.

Jun 25, 2024

Underground mining alters ground condition, producing a disturbance in the ground water regime. The level of disturbance is dependent on the local hydrology, geology, and type of mining. Serious damage is sometimes caused by ground water- when mine roofs collapse, causing subsidence. Subsidence is either unplanned, where pillars are inadequate to provide support; or planned, where total extraction occurs over a large area. The primary objective of this study is to investigate the effects of mine subsidence on the ground water hydrology in the Warrior Coal Basin. Underground openings resulting from coal mining activities have been the most significant cause of subsidence problems in the Warrior Coal Basin, the main source of coal in Alabama. This problem will be even more serious in the future because 19 of Alabama's 24 billion tons of coal reserves are classified as an underground source (Tolson, 1982).

Jan 1, 1987

By Yuting Xue, Xin Li, Ihsan Berk Tulu, Gaobo Zhao, Deniz Tuncay, Mindi Ruan

Most coal mine roofs in the Appalachian region consist of laminated shale, which is prone to brittle failure. Accurate modeling of shale roofs is vital for studying cutter failures of these shale roofs, and ordinary and formational bedding planes play a significant role in the response off the shale roof to mining-induced stresses. This paper presents a robust method for constructing three-dimensional shale roof models using limited borehole cores and leveraging image processing techniques. The approach begins with image extraction from shale cores. Then, we extract the portions that feature the core and employ image-stitching techniques to merge them seamlessly. Once the images are stitched, they are duplicated horizontally and merged to create a cross-sectional plane image representing a shale roof. This roof cross-sectional plane image serves as an input to our proprietary Digital Image Processing (DIP) algorithm, which is adept at extracting ordinary bedding planes (interfaces that represent color transitions between a single shale unit). The extraction process involves transforming discrete core points (ordinary bedding plane pixels) into continuous lines representing ordinary bedding planes. Finally, extending this method into the third dimension, the model is further extrapolated to form a comprehensive three-dimensional shale roof. Through this process, the geometry information of ordinary bedding planes can be extracted for each type of shale in cores, including sandy shale, gray shale, dark shale, etc. This work bridges the gap between limited core data and comprehensive 3D geological modeling, offering valuable insights into identifying and quantifying the variations in different shale roof geologies.

Jun 25, 2024

By Paul A. Rittenhouse

Its a pleasure to be with you this afternoon and to talk briefly on one of my favorite subjects -- the U.S. sulphur industry. As our Chairman mentioned, I have been associated with the sulphur industry either directly or indirectly for the last twenty years, both on the production side and as a consumer. Sulphur, while unseen and relatively unknown to most people, is like margarine ... that ubiquitous spread ... that is yellow and nearly omnipresent in the industrial world. It is because sulphur, in some form, is required in nearly all aspects of our economy that makes its study so interesting to me as a researcher. An analysis of the sulphur outlook requires examination of such industries as fertilizer, paints and pigments, copper and zinc, uranium, petroleum, chemicals, pulp and paper and textiles - just to name a few. Of course, because its use is so widespread and ever-changing it is difficult to develop and maintain a good understanding of the sulphur industry. It is also a problem to cover the industry in a short discussion and to project its really dynamic nature. Hut, if you will bear with me, I will attempt the task. First of all, let me say that sulphur today is a world commodity and to a large extent moves freely in world trade; nearly a third of the world's sulphur or something over 15 million tons in 1974 entered international trade. However, today our interest is in the current changing sulphur picture in the U.S., with particular emphasis on the western part of the country.

Jan 1, 1975

By Morton Handelman

The extraction of aluminum oxide_ from its ore is the initial step in the commerical production of metallic aluminum. This is most commonly done by the Bayer Process in which a caustic solution is used to dissolve hydrated alumina from the insoluable materials with which it is associate in bauxite. At the two-thousand ton per day Sherwin Alumina Plant of Reynolds Metals Company, the extraction residue from Caribbean ores is removed from the main pro¬cess stream as the underflow of a continuous clarifier-thickener operation. This sludge, prior to its ultimate r4jection from the process, is washed in a nine-step continuous countercurrent decantation system to recover physically-entrained mother liquor. Control of alumina production costs requires the optimum recovery of solubles from this residue which is generated at the same rate as the finished product. The equipment, operating techniques, controls and process variables which affect the efficiency of this soda recovery from Bayer Process red mud will be discussed.

Jan 1, 1959

By R. S. Hearon

The image of the open-pit miner in the eyes or the Environmentalist has never been very outstanding. The phosphate industry, whose history in Florida reaches back to the late 1800's, can-not be credited until recently with a large number or accomplishments in terms of protection or the environment to change this image. This lack of action was not deliberate or in opposition with the desires of the public. In the formative years, there was little or no public and the companies found it necessary to build towns to house their employees and their families, towns which remained in existence until the late 50's and early 60's or formed the core of present large communities. Neither these pioneers nor most subsequent resource developers considered themselves un-thinking spoilers, nor were they so regarded by their contemporaries. Instead, they acted in a manner consistent with their environmental circumstances and intellectual heritage. Early Americans did make mistakes in using the land but the mistakes became apparent only in the opinion of later generations. Over the past five to ten years, there has been a new self-awareness in the industry with regard to environmental responsibilities brought about, in part by a continuing onslaught of new regulations with jurisdiction over our activities. Part of the new regulations are aimed at industries as a whole while many, particularly state regulations, pertain specifically to the phosphate mining industry. Why all the new regulations? The reasons are encased in a complex web of activity but stem primarily from a new public awareness of its environment. More and more of our youth have become interested in the environmental science areas such as biology and ecology. The tremendous growth rate in both the population and industry has made personal issues out of subjects such as atmospheric inversions and water shortages which previously were abstract concepts. The State has grown from a population of 1,500,000 in 1930 to approximately 9,000,000 people today. This personal impact and general lack of knowledge on the part of the public concerning economics has resulted in big business no longer being held in awe, often in contempt and generally in suspicion where environmental concerns are encountered.

Jan 1, 1978

By Cal D. Iles

Decreasing ore grades and increasing labor and material costs have seriously eroded the economic vitality of many mining operations. Coupled with global economic stagnation and recession in the early 1980's, these conditions have forced reevaluation of operating strategies and methodologies with the objective of remaining competitive in a world marketplace. A concept offering large potential benefits is hardrock portable crushing and conveying. Implementation of this system at Duval Corporation's Sierrita open pit copper-molybdenum mine (Figure 1) has significantly reduced mining costs, becoming a major part of Sierrita's cost reduction strategy. Located 48 km south of Tucson, Arizona, the 209 000 t/d property has one portable 60x89 gyratory ore-crusher in operation with tentative plans for two additional units.

Jan 1, 1985

By R. J. Thompson

Well-designed and maintained haul roads are the key to minimizing truck haulage onroad hazards and costs, as well as increasing productivity. In practice, however, designing and managing a haul road for optimal performance is often difficult to achieve, especially when resources assigned to design and construction are constrained. By understanding how a road design is developed from geometric, structural, functional and maintenance considerations and, critically, the interplay between these components in design and operation, optimal performance can be achieved. This paper briefly summarizes the evolution of mine haul road design, from the seminal USBM work of Kaufman and Ault in 1977, through to current geometric, structural, functional and maintenance management design components. These augmented design and management guidelines have been developed over the past decade, both in response to the requirements of mine operators for safer and more efficient haulage systems, the truck manufacturers’ requirements for a more predictable and controlled operating environment and the recognition of human factors as a significant contributor to haulage accidents. While the human factor is the most problematic to address in a road design, the paper shows that the more that is known about human error, the better a road can be designed to accommodate those actions or non-standard practices that would, on a poorly designed road, invariably escalate an error into an accident.

Jan 1, 2010

By Brent W. Madsen

To assist in fulfilling the Bureau of Mines goals of maintaining adequate mineral supplies to meet national economic and strategic needs, and to minimize the environmental impacts associated with mineral-processing operations, a leaching-solvent extraction-electrowinning technique was compared with a leaching-cementation technique for processing low-grade copper ores. Large-scale laboratory column leaching tests (6 to 7 tonnes) were conducted on minus 37-cm chalcocitic ore using ferric sulfate leach solutions at 25° C. Two columns contained 11 percent minus 1.27-cm fines, and two columns contained 32 percent minus 1.27-cm fines. After 416 days of leaching ore samples containing 11 percent minus 1.27-cm fines, copper extraction was 48 and 51 percent for the leach-cementation and leach-solvent extraction-electrowinning procedures, respectively. When leaching ore samples containing 32 percent minus 1.27-cm fines, the leaching-solvent extraction-electrowinning technique extracted 60 percent of the copper after 568 days, whereas the leaching-cementation technique extracted only 48 percent of the copper. In the latter test, leach solution ponded on the ore, which reflected a decrease in ore column permeability. The decreased permeability was attributed to the generation of excessive amounts of iron salts during cementation; the salts precipitated on the fine ore particles and in the interstices, thus plugging the column. This decrease also lowered the available oxygen, resulting in poor aerobic bacterial activity which slowed the oxidation rate of ferrous ions to ferric ions. Sulfuric acid required to maintain a leachant pH of 2 was nearly halved when copper was recovered by solvent extraction and electrowinning rather than by cementation.

Jan 1, 1979

By Ehsan Alavi, Brian Hagan, Glen Frank, Michael A. DiPonio, Michael Mooney, Lisa Mori

"The data from EPB cells located inside the pressurized chamber of EPB TBMs and also the data from the pressure sensors in grout lines are quite important in controlling the EPB operation. However, there have always been questions in regards to pressure distribution along the shield body. Could the pressure distribution data be used to come up with potential locations for ground loss? Does the overcut region, the space between the shield body and the maximum cut diameter, consist of broken material or EPB muck, or does that region consist primarily of void space? During free air interventions, how does pressure distribute along the TBM body? To address these questions, one of the two EPB TBMs used in the Northgate Link Light Rail project in Seattle, WA is equipped with EPB cells in front and rear body to monitor the pressure distribution along the TBM body in addition to the standard 6 EPB cells located inside the cutterhead chamber and pressure sensors located at the grout lines. This paper discusses the results of this study and weighs on the valuable data that can be collected by using the shield pressure sensors.INTRODUCTIONThe cutterhead of the TBM is normally equipped with overcutters on the cutterhead periphery which extend into the annular space beyond the diameter of the TBM shield. Thus, the overcutters serve to disturb and excavate some of the ground in the annular space which reduces friction and resistance around the TBM body. This phenomenon is necessary to help the TBM steer and navigate around curves. Additionally, the shield of an EPB TBM is also often shaped like a cone, with the diameter decreasing from the front to the tail shield. This conical shape also helps the TBM to navigate because material that is cut by the cutterhead either gets pulled into the cutterhead or it gets pushed out of the way – around the cutterhead and into the annular space. In EPB tunneling, the conditioned material from the face that does not get pulled into the cutterhead mixing chamber flows into the shield gap and pressurizes the surrounding ground. Additionally, grout can travel from the segment annulus into the shield gap. The pressure in the shield gap mainly depends on the pressure of the material at the face and the grouting pressure behind the tail shield."

Jan 1, 2016