Search Documents

By D. L. Schenk

The Navajo Mine is exclusively a multiple-seam surface coal mine located in the northwest comer of New Mexico. The property is situated entirely on the Navajo Indian Reservation. It is owned and operated by the Broken Hill Propriety Co. Ltd., of Melbourne, Australia. The mine began production in January 1963 with a long-term fuel supply agreement with the Four Corners power plant. The 2175 MW nominal generating capacity of the Four Corners powerplant consumes 7.2 Mt to 7.7 Mt/a (8 million to 8.5 million stpy) of coal. The Navajo Mine has estimated reserves totaling 1 Gt (1. I billion st) of strip minable coal. Only about one-third of that total is presently committed to the generating station. As development continued over the years, mining operations advanced into more complex geologic areas to satisfy the utility's demand for coal. To optimize the committed reserve and provide competitively priced coal to the customer, the Navajo Mine began developing a new pit in June 1986. The Dixon Pit boxcut development was completed in April 1987. About 6 hm3 (7.9 million cu yd) were stripped, uncovering 929 kt (1 million st) of coal. Strip ratio was 7.74:1 including 36.8% rehandle of prime yardage. This case study of the fourth production cut highlights a variety of dragline stripping techniques including highwall bench (overburden) side cast, intermediate highwall bench (parting-interburden) side cast and spoilside bench (partings-interburden) stripping methods. The Dixon Pit offers considerable challenges in the surface recovery of up to seven seams of coal within the 1432 m (4700 ft) of total pit length.

Jan 1, 1990

By Tim Cleary, Steve Skelhorn

The 9th Line / 16th Ave tunnels are part of a $700 million expansion of the York Durham Sewage System, north of Toronto. The 15 km of tunnels presented many challenges, including glacial and postglacial deposits, at depths up to 55 m. Due to high hydrostatic heads, the Owner specified EPB tunnelling, however, an alternate was proposed utilising rib and lagging tunnels, combined with a de-watering scheme. State of the art technology was utilised with a new Lovat TBM, incorporating PLC control, soft start water-cooled motors and a head designed to tackle the mixed ground expected. The 9th Line tunnels were completed in 2002. Subsequently the second section of tunnel along 16th Avenue has been awarded to the Joint Venture. This paper presents a case history of the soft ground tunnelling, including design elements, tunnel systems and TBM operations.

Jan 1, 2003

By D. E. Ranta, M. G. Hester

The ore reserve modelling of stratiform uranium deposits to be mined by selective underground mining methods must be done with consideration of the erratic nature of the ore-forming processes that produced the mineralization. Estimation methods that model the uranium grade as a smooth transition between high-grade and low-grade drill hole intercepts tend to greatly overestimate the ore tonnage. Care must be taken to first establish realtistic ore pod geometries and then estimate the grade of the reserve units within the pods.

Jan 1, 1992

By Frank F. Aplan, G. Rinelli

INTRODUCTION Coal is a solid, combustible mineral substance resulting from the degradation and alteration of vegetable matter largely in the absence of air. In this natural process of coalification, some non-combustible mineral matter is always associated with the combustible material. Coal preparation or cleaning is the process of removing this inert mineral matter from the coal. Preparation is highly successful in removing the large fragments of inert material, but is not very effective in removing the fine inorganic mineral matter intimately associated with the coal. Of the 600 million tons of coal produced in the United States every year, approximately one-half is produced by coal cleaning methods (1). The bulk of this tonnage is cleaned by coarse or intermediate gravity preparation methods (5 inches to 28 mesh, Tyler). Fine cleaning, say, -28 mesh, is done by shaking tables, washing cyclones, and flotation, or, until recently, the fines were either incorporated into the clean coal or simply discarded--not infrequently, the latter. In 1972, only 13 million tons of raw coal were cleaned by flotation in the United States, and from this 8.4 million tons of clean coal were produced (1). The percentage of clean coal produced by flotation in Europe (England, West Germany, Poland, U.S.S.R., etc.) is substantially higher. However, coal flotation has grown rapidly in the United States from only a few plants in 1950 to 31 in 1960 (2) and 66 in 1970 (1). Virtually all new preparation plants incorporate flotation into their basic flowsheet. The essential difference between ore and coal flotation is that for ores the entire tonnage is ground to flotation size, whereas for coal

Jan 1, 1976

By Donald E. Zipperian

It has been recognized that froth flotation of mineral particles utilizing rising flow of micro size air bubbles, counter-current to quiescent falling flow of particles in a column type cell, provides a unique mechanical atmosphere conducive to extension of froth flotation process to much coarser and finer particles sizes than possible with mechanically agitated and aerated cells. 1,2,3,4. This paper describes metallurgical results obtained at several plant installations of large capacity commercial size Deister FLOTAIRE® Column Flotation Cells. These cells utilize air aspiration into surface tension lowered water to generate micro size bubbles. Operating costs, power, wear, and scaling characteristics of rougher, cleaner, and scavenger units are compared with mechanical units. Problems encountered and scale up criteria developed when increasing from 0.20m(8inch) diameter pilot cells to 2.42m(96inch) commercial cells are discussed.

Jan 1, 1985

By David J. Akers

INTRODUCTION The variety of uses of coal and the wide range of characteristics of coal combine to produce a need for a wide variety of laboratory analysis. Coal is used to heat homes, produce electricity, and make coke for steel manufacture. It can also be used to produce both gaseous and liquid fuels as well as a variety of chemical products. Various applications may require specialized analytical procedures. For example, some of the procedures developed for the coke industry, such as expansion or contraction during carbonization, have little value to the power generation industry. Even for a single application, the type of analysis needed can depend on the source and/or general nature of the coal. This section provides a general overview of the types of analytical procedures commonly applied to coal from the perspective of the user of this information, not the producer. The intent is not to detail laboratory procedures, but rather to discuss the application of commonly used laboratory tests in coal preparation. Accordingly, laboratory procedures are categorized by type of information produced. Gravimetric Analysis Procedures that produce weight-based information (parts per million, pounds per cubic foot, or weight percent). Such analyses can relate to the coal's physical, chemical, or mineralogical characteristics. Volumetric Analysis Procedures that produce volume-based information (amount of a mineral present as a volume percent). The primary source of volumetric information is from petrographic analysis. Application Tests Procedures that measure some characteristic of coal that has been empirically related to some application or handling or processing step. Typically, these procedures attempt to duplicate some aspect of the commercial application at laboratory scale and may produce information in the form of an index. Applications procedures do not measure a single component of the coal but infer the combined effect of multiple components. Each class of information is discussed in the order listed. References are provided as a source of more detailed information. The American Society for Testing and Materials (ASTM) publishes the most inclusive reference to analytical procedures. This publication,16 which is revised annually, provides extensive information concerning generally accepted methods of laboratory analysis. ASTM also provides standards for sampling and some information concerning sample handling.

Jan 1, 1991

General. Data for the operating information given in the 15 tables in this chapter was obtained from voluminous questionnaires sent to over 100 operating companies in 1972. There has been a considera¬ble change since then in supply and power costs and many companies have had expansions or revisions since that time, so it must be realized that information is valid for the year 1972. This is true except for the three new properties of Sacaton, Metcalf, and Pinto Valley. These three operations started up since 1972 and all information for them was obtained in 1975. The questionnaires were sent to all major copper properties throughout the world as well as to many smaller units and to some mines that had complex or unusual conditions. Properties for which no information is given did not submit completed questionnaires. Several operations were unable to supply information requested be¬cause of company policy prohibiting it. However, data is presented for 75 different operating properties. The reference number of the left-hand column is the same for all 15 tables of data. If the company had several operating properties as of 1972, then subsequent properties use the same number but a different letter. For example, Anaconda's property at Butte, Mont., is IA, whereas Anaconda's (now Anamax) Twin Buttes property in Arizona is IB. Table I gives general data for the properties including exact loca¬tion, milling rate, pertinent assay values and recoveries, and a brief listing of ore and gangue minerals. It was not possible to obtain any more information from the properties in Chile except that given in Table I. Crushing. Crushing plant operating data is given in Table 2. This table gives data on the crushers, feeders, and screens used at each property. The data obtained on feeders was confusing, but, rather than completely eliminate this information, it was decided to report it as given. The confusion lies only in the description of where the feeder is located. Where a primary feeder is listed it was not possible to determine if this feeder was on primary feed or primary discharge. For secondary feeders it is known that the feeder listed usually is feeding the secondary crushers, but at some properties it is handling the secondary crusher discharge. The same reasoning holds true for tertiary feeders-they handle either tertiary feed or discharge. This table contains a voluminous amount of data. A column giving tons per day per square foot of screen area would have been very informative, but some properties included circulating load in the feed rate and others listed new feed only, so calculations were meaningless. Autogenous Mills. The use of autogenous or semiautogenous mills for any property must be given serious consideration in the future. Table 3 lists data for four properties that are fully autogenous and four more semiautogenous mills that use balls to supplement the chunks of ore. This method of grinding is especially applicable when the ore is of such a nature that crushing problems would be severe, such as when ore is wet or sticky or contains a lot of fines. Paradoxically, it should also be considered when ore is tough and hard and blocky because then the competency of the ore means it can serve well as the grinding media. Where the ore varies greatly in hardness, as at Cyprus Pima and Lornex, semiautogenous grinding has been especially beneficial with capital costs and operating costs both 10-20% lower than could be obtained with conventional crushing and grinding. Rod Mills. For a great many years the standard milling operation used two- or three-stage crushing followed by open circuit rod mills and then ball mills in closed circuit with classifiers of some kind. A surprising number of properties crush to the fine size of about 3/8 in. and then use ball mills only, in closed circuit, with no rod mills. It is difficult to say whether rod mill-ball mill circuits or ball mill only is the best. One can be certain of two things: (1) the argument will go on for a long time and (2) for some mills one method obviously was superior over the other. As ball mills of 14, 15 ft, and larger came into use, more properties like Duval Sierrita (16b ft diam by 19 ft long) and Bougainville (18 x 21 ft) were built with single-stage ball mill grinding. Although there are larger rod mills used, especially in the iron ore industry, the largest rod mills on copper ore are at Twin Buttes (14 x 18.5 ft) and at Gibraltar (13'A x 20 ft). Table 4 lists operating data for rod mills. If a company is listed in Table I

Jan 1, 1985

By D. R. Zuchelli

The purpose of wrapping ball mills with thermal/acoustic blankets is twofold: 1) to maintain the desired temperature inside the mill, and 2) to reduce the sound emanating from the mill. This field case study focuses solely on the latter, evaluating and documenting the sound level reduction attributed to the installation of the blankets on ball mills and its potential to reduce the noise dose experienced by the process attendant. One of the three ball mills had already been treated (baseline) before the evaluation started. However, treating the remaining two mills still proved to be very effective, further reducing ball mill noise in the near field by as much as 10.0 dBA and producing far field noise reductions of 3.0 dBA or greater, extending as far as 35 feet from the mills and to the floor above. The model developed from the survey data shows that a process attendant spending a substantial portion of a shift in the mill building will experience a significant reduction in overall noise dose.

Jan 1, 2010

By D. S. Choi

The paper contains a subsidence measurement taken over a room and pillar panel of a mine located in northern West Virginia. A total of 72 monuments were used to determine a three dimensional view of mine subsidence. In addition, the results of measurements were used to compute ground strains with the use of a numerical model.

Jan 1, 1982

By T. Tamagawa, I. Iwasaki, N. X. Fu, M. Kobayashi

A three-stage fluidizing-bed process consisting of chlorination, selective oxidation and sulfur chloride conversion was tested for processing chalcopyrite concentrate. It was found that the use of excess oxygen was essential for the stable operation of the oxidation reactor. The excess-oxygen gas inevitably causes the oxidation of the sulfide concentrate in the chlorination and sulfur chloride conversion reactors. A new flowsheet is proposed to separate the chlorination and selective oxidation steps with separate flow paths of the fluidizing gases, thereby, preventing the passage of excess-oxygen gas in the chlorination and sulfur chloride conversion reactors. The feasibility of the proposed flowsheet was demonstrated in a laboratoryscale fiuidizing bed setup.

Jan 1, 2002

By S. K. Kawatra, J. A. Halt

"INTRODUCTION Iron ore beneficiation needs advances in areas such as process control, automation, burner and furnace designs, silica-free binders, and even alternative iron making routes. While some – like new binders – are only step-changes, all are tools that can help make the ironmaking industry more sustainable. This paper focuses on binders. Binders are added to iron ore fines before they are agglomerated. Binders are used to control the balling process and increase the mechanical quality (e.g. strength) of green-balls and pellets. Agglomeration usually follows thickening and filtration. Good-grade ores, which don't require upgrading, are wet ground to decrease particle size and increase specific surface area. Low-grade ores are often extensively upgraded through wet operations (flotation, dispersion and selective flocculation, magnetic separation, etc.). For both types of ores, thickening and filtration conclude the circuits so that moisture contents are lowered and the ores can be agglomerated. It's been known for a long time that thickening and filtration behaviors are influenced by zeta potential (Sandvik, 1979). Highly-negative zeta potential is good for dispersion while low zeta potential is good for filtration. So, the zeta potentials of iron ore particles are lowered with additions of acid or carbon dioxide, for example, to increase filtration rates and throughputs (Eisele et al., 2005). What happens to particles as their zeta potentials are lowered? Particles aggregate together, effectively forming larger particles. How stable then, are those aggregates during mixing and balling? Are they easily broken up during mixing (if mixers are even used)? Are they broken up during balling? Or, do the aggregates resist breakage so that the availability of ultra-fines, which are so beneficial for agglomeration (Stone, 1968), is decreased? For plants where high doses of bentonite are used as binder, the above questions may be of no concern. The bentonite adds the necessary amount of fines; however, even at those plants, the calcium and magnesium contents in the water affect bentonite's effectiveness (more magnesium and calcium means less effective bentonite). (Engesser, 2003) For plants where new silica-free organic binders are being developed and used, the above questions may need to be considered. The binder is only amongst the iron ore particles for a short period of time – until it burns away or thermally decomposes in the induration furnace – so the liberation, availability and distribution of fine particulates is very critical for the quality of balls and pellets. It was hypothesized that high zeta potential conditions would lead to good pellets, while low zeta potential conditions would lead to relatively bad pellets."

Jan 1, 2018

By Wayne Taylor, Martyn Dawborn

Simulation modeling of portions of two platinum mines using General Purpose Simulation Software (GPSS/H™) is presented in this paper. Both mines, located in the Bushveld Igneous Complex PIC) of South Africa, exploit Merensky and UG2 reef horizons, which are processed separately and therefore handled individually from the stope face to surface, requiring duplication of storage arrangements and batch operation of transport facilities. The first simulation assignment concerns the upgrading of a shaft system operating exclusively on Merensky ore, to hoist UG2 ore and increase production. The second assignment comprises a simulation of rock flow from the stope face to surface by way of tramming, inclined conveying and vertical hoisting. Development ends and stope boxholes were modeled down to individual hoppers (cars) demonstrating the versatility of the GPSS/H™ language.

Jan 1, 2002

By Al. Valero, A. Domínguez

This paper appraises the energy requirements for mineral production through an exergy approach taking into account the long-term decline in ore grades. In this context, the exergy required for restoring resources from the dispersed state of the so called Crepuscular Earth into the physical and chemical conditions in which it was delivered by the ecosystems in light of the available technology, is known as exergy cost. The exergy cost is the point of reference in order to evaluate in a single variable, characteristics such as composition, concentration (ore grade) and the state of technology. The ratio between the exergy cost and the minimum thermodynamic cost required to accomplish the same process is called unit exergy cost and provides a measure of the irreversibility of the analyzed processes. Otherwise, the ore grade is one of the main issues which affects directly the costs associated with mining the ore. Hence, the unit exergy costs to produce minerals from progressively lower ores grades by the current technology is analyzed. The unit exergy cost curves are presented for some important minerals such as aluminium, chromium, cobalt, copper, gold, lead, manganese, nickel and zinc, in order to know the trend when the ore grade decreases.

Jan 1, 2011

By Kendall Y. Keuhey

The Mercur Mine, developed and operated by Getty Mining Company, is designed to process 3,000 tons/day of gold ore from the historical Mercur Hill mining district. The mill process involves crushing, grinding, and cyanide carbon in leach for recovery of gold ores ranging from 0.08 to 0.10 oz/ton. During the mining of normal grade ore, a substantial tonnage of material containing 0.02 to 0.05 oz/ton is mined and would be available for heap leaching. Also, Getty Mining is developing methods to test and prepare lower grade material for heap leaching by rejecting a course rock fraction from the grinding circuit SAG mill. This lower grade fraction is suitable for heap leaching, and its removal will upgrade the regular mill feed. Other test methods are directed toward leaching techniques on some 4.0 million tons of tailings that resulted from roasting and/or cyanide leaching Mercur ores in the early 1900s. The natural carbons associated with the Mercur deposits require special treatment to reduce their gold adsorption effects when leached with cyanide.

Jan 1, 1983

By Roger Holmberg

INTRODUCTION The driving of drifts is a very important aspect of underground mining. It is not unusual for the percent¬age of rock broken during development in a mine using sublevel caving, for example, to be as much as 25% of the total. If one also considers the amount broken for transport, ventilation, and exploration drifts, one can easily understand that the planning and excavation of drifts play a major part in the total economics of the mine (Fig. 1). Increasing mechanization in mining demands larger tunnel areas for transport and mining equipment. With modern machines the hard work involved in using hand¬held pushers is gone, and a better environment is achieved. More rational methods could be used, but much of the experience the working man acquired by working close to the rock face (such as utilizing the natural weak planes in the rock when he placed the drill¬ing holes) has unfortunately been lost. By having sepa¬rate shifts for drilling, loading, and hauling, more atten¬tion has to be placed upon a well-designed drilling pattern. Some reduction in the number of holes required can be achieved with mechanized drilling because of the larger holes that can be produced. On the other hand, it is probably not possible to achieve the same precision as with pneumatic pushers, and it is difficult to utilize the larger holes because these cause more damage to the re¬maining rock. Recently, however, the precision has be¬come very good with the parallel booms and automatic devices for setting the lookout angle (Fig. 2). A larger arch of the drift roof requires a more carefully executed blasting procedure than before in order to prevent rock fall and to insure a sufficiently long stand-up time. In this chapter, empirical relationships that can be used to design an economic and optimal drift blasting design will be presented. The principles of the calcula¬tion method are based upon the earlier work of Langefors and Kihlström (1963) and Gustafsson (1973). COMPARISON OF EXPLOSIVES To provide for the use of various explosives it is necessary to have a basis of comparison. Several meth¬ods have been developed to characterize the strength of an explosive. Some examples are comparison of values given by (1) calculated explosion energies; (2) the ballistic mortar test; (3) the Trauzl lead block test; (4) the brisance test; (5) the weight strength concept; and (6) the underwater test. However, most of these meth¬ods should be used carefully when stating the breaking

Jan 1, 1982

By Matthew Wilcock, Kenichi Soga, Peter Wright

"This paper discusses how an existing grey cast iron segmental tunnel lining responds to construction of a new SCL tunnel transversely beneath with zero clearance; how the damage assessment for the existing tunnel was conducted for impact of longitudinal movement; how the tunnel is subsequently instrumented to observe both movement and stress manifestation at its longitudinal connections and how the results from the instruments compare with the prediction. An assessment of neutral axis of the tunnel in longitudinal flexure is also explored using interpolated horizontal displacement data from a conventional monitoring system. INTRODUCTION The Royal Mail Tunnel (RMT) (formely Post Office Tunnel or ‘Mailrail’) was constructed using semi-mechanised deep level construction techniques from 1914 and 1917 (Lee 1938). Commencing full commercial operation in 1926, the system was until 2003; conveying parcels the 6.5 miles between seven sorting offices in the center of London, and linking the system with main line rail stations, Paddington and Liverpool Street (The British Postal Museum & Archive 2013). A single tunnel of 2.74m internal diameter facilitated a bi-directional twin narrow-gauge (~611mm gauge) railway road system for electric driverless operation. The tunnel lining is segmental grey cast iron (grade 10) made up of six flanged segments and a smaller flanged key segment; constructed into a ring of width 508mm The external diameter of the tunnel is 2.971m. For further details of the tunnel lining and material properties are outlined by (Devriendt & Alhaddad 2014).London Underground Bond Street Station is a major station of the London Underground system in the very center of London; in its vicinity, the RMT runs west-east perpendicularly above the north south Jubilee Line tunnels. Historic survey record of the Jubilee Line’s (the then Fleet Line) construction in 1974 and its impact on the RMT case is documented in (Crossrail 1993): it is one of only a hand full of case-studies frequently cited when assessing the impact of new construction scenarios of this type; not least including the assessment of the same tunnel, at the same site some 40 years later, and the subject material for this paper: It noted significant vertical displacement of ~90mm to the RMT without noticeable serviceability or operational impediment."

Jan 1, 2016

By Roland Trunk, Marcel Imbach, Yves Boissonnas, Jan Vesely

"INTRODUCTION The expansion of the Suez Canal, which runs between the Mediterranean and Red Sea, is at the top of Egypt’s economic agenda. The £8 billion development plan includes a new channel alongside the existing one which will double the number of ships able to pass each day and several tunnels to connect the Sinai peninsula to the main part of Egypt. The Egyptian government ordered three new tunnels under the Suez Canal in the area of Port Said as part of the Canal Region Development Plan. The three tunnels will contribute to the North Sinai expansion, helping to create a vast industrial zone and completing the coastal road extension from Rafah to Nuewiba. Two of these three tunnels will be allocated for roads and the third for railway traffic. A further part of the Suez Canal development mega project are an additional six tunnels in the area of Ismailia and Suez. The focus of this paper is on the two road tunnels in Port Said and will give an overview of the project and the challenges encountered regarding the technical complexity and tight time schedule both in its design and execution. PROJECT OVERVIEW The tunnels will be built in the area of Port Said (see Figure 1) which is the most northern part of the Suez Canal.The road alignment connects the Port Fuad Road in the east bank of the Suez Canal to the Port Said-Ismailia highway in the west bank with a dual carriageway section. Each of the carriageways has two lanes. The bored diameter of the 2.8 km long road tunnels is 13.050 m and will be driven with two Mix-Shield TBMs. The distance between the two tunnel axes is planned with 42.5 m (discussion about a reduction are ongoing). The width of the Suez Canal is around 340 m at upper level and around 170 m at the bottom. During the TBM drive, three main geological layers are expected. Below a depth of around 40 m in a very soft clay layer, a dense to silty sand layer is predicted. Within the sand layer another silty hard clay is expected in different depths with variable thickness. After finishing the excavation of the road tunnels, the same TBM will be used for the railway tunnel. The lowest points of the road tunnels will be located 59 m below the surface (tunnel invert to surface) and only 18 m of ground cover exists between the tunnel crown and the Suez Canal invert. Minimum ground cover over the tunnel crown is approximately nine meters at the tunnel portals."

Jan 1, 2016

By A. Juganda, Jr. Bogin, S. A. Lolon, J. F. Brune, J. W. Grubb

"A longwall gob is mainly filled with broken rocks from the collapsed roof and becomes a porous medium where explosive methane-air mixtures can accumulate. In bleeder ventilation systems, this mixture can migrate out of the gob into the longwall face and other active areas in the mine during barometric or ventilation-induced pressure changes. When external pressures change, the gob does not perceive this disturbance instantly but with a delay due to air flow resistance in the porous gob material. The delay of gob response to outside pressure changes increases the pressure differential across the gob and may cause an outflow of explosive air mixtures from the gob into the adjacent bleeder entries. With computational fluid dynamics (CFD) modeling, researchers at the Colorado School of Mines have evaluated the impact of gob pressure fluctuations on the outgassing of the explosive gas zones (EGZs), the magnitudes and rates of pressure changes, the volumes as well as the potentials location of outgassing if it occurs. INTRODUCTION The air pressure field in underground mines is controlled by many factors such as operating fan settings, ventilation controls, surface atmospheric conditions, and other local events that can intermittently disturb mine pressure, including blasting, roof falls, or inundations. Mine fan settings are rarely changed. Mine atmospheric pressure fluctuations due to adjustments in ventilation controls occur more often during the mining process. Atmospheric conditions and barometric pressures can generate fluctuations in mine pressure on a large scale. Atmospheric pressures change regularly every day but can fluctuate abruptly and become increasingly hazardous in adverse weather conditions. Investigations conducted in coal mines in the United States, Australia, Poland, and South Africa observed higher methane emissions from the gob during periods of falling atmospheric pressures, which led to mine explosions (McIntosh, 1957; Boyer, 1964; Kissell et al., 1973; Fauconnier, 1992; Belle, 2014; Wasilewski, 2014; Lolon et al., 2015). Falling external pressures are understood to cause potential outflow of explosive mixtures from the gob, while rising pressures may push fresh air into the gob. This phenomenon is widely known as gob breathing. The actual processes that trigger gob breathing are not fully understood, nor are the parameters that contribute to the process. Other major events such as roof falls or fan failures can also change the pressure conditions in the mine. In contrast to atmospheric pressure changes, these events can change mine pressures much more rapidly or immediately. TIME LAG AND GOB BREATHING CONCEPT In a bleeder ventilation system, the pressure in the gob is designed to be lower than that of the headgate entries and the longwall face. Air from the gob and gate entries flows towards the tailgate-bleeder returns. When the external pressures are disturbed, this designed pressure arrangement may change, potentially resulting in increased outflow from or inflow into the gob."

Jan 1, 2017

By Adrian J. Mathias

For many years excavations were made in rock exclusively by conventional blasting methods, and without concern for damage to the rock surfaces which remained after the excavation was completed. Recently, however, there is an increasing awareness for the importance of making rock excavations with as little damage as possible to the remaining rock surfaces; consequently, several revolutionary new precision blasting techniques have been developed during the past few years. These techniques, variously known as cushion, smooth- wall, perimeter, pre-shear, and pre-split blasting, basically involve the creation of a fracture plane in the rock between a series of blasted holes. The variations in each of these techniques are largely due to the differences in hole diameters, hole spacings, methods of charging, and sequence of blasting used to achieve certain specific results. The development of these precision blasting techniques was initiated by Canadian Industries Limited in 1953 at the time the Sir Adam Beck No. 2 Hydro-electric Project was under construction by the Hydro-Electric Power Commission of Ontario. Since then, these techniques have been somewhat advanced, and they have been applied with varying degrees of success to a number of projects. These projects include railroad and high- way cuts, dam spillway channel excavations, canal excavations, tunnel driving, shaft sinking, and other underground applications.

Jan 1, 1965

By A. M. Galperin

Back analysis is a very important procedure for proper understanding of physical processes. Back analysis can be used to establish the role of different factors, define parameters to be calculated and formulate the behavior of natural or physical processes based on field experimental results. It is evident that, in order to obtain the necessary data for back analysis, field observations are required. For the Michailovsky region (Kursk Magnetic Anomaly, KMA) the long-term strength characteristics of the clay covering the quarry slopes were established with the help of back landslide calculations. The obtained data allowed quantification of the shearing resistance parameters at the presence or absence of intermittent dips of discharge in the pit bank massif structures. Based on the results of investigation for material composition, strength and deformation of finely dispersed (clay-chalk) deposits in the Kursk Magnetic Anomaly including measuring of the settlements of filled structures, complex probing and laboratory determination of water-physical and mechanical properties of "man-made" soils, engineering-geological zoning of filled structures was carried out.

Jan 1, 2005