Search Documents

By Harold L. Lovell

The areas of application, the limitations imposed by water chemistry as well as the advantages and disadvantages in the use of limestone for the treatment of coal mine drainage have recently been described by the authors (1),(2), (3). The process has been demonstrated in continuous, full-scale operation to yield a treated water meeting specifications established by the Pennsylvania Sanitary Water Board and containing excess alkalinity. Their final pH levels are usually less than seven, a condition which avoids consumption of excess neutralization reagents, but which occurs with lime-based processes and results from unwanted side reactions. Operating experience has been cited by Calhoun (4) using ferric waters while others (5), (6), (7), (8), (11), have reported on related research efforts. Despite the advantages including ?the relative simplicity, and minimal costs of the process, there have been very limited industrial applications of mine drainage neutralization with limestone. Although any treatment of these waters may be considered as a temporary control measure (9), the lack of feasible, immediate alternatives, the extensive magnitude. of the waters and the high cost of treatment requires that optimum processes should be utilized and that operating experience in their use be developed as is feasible. This paper will review treatment experience with a ferrous water of moderate pollution loading .

Jan 1, 1972

By M. Guzman, M. Romero, S. Bravo-Thais, M. Flores

The phytoremediation method is proposed to recover valuable metals from polluted soils. In this sense, the objective of this research is to determine if it is possible to use native plants in the recovery of precious metals from abandoned mining liabilities. The tailings samples containing Au and Ag were acquired from the northern region of Peru. Two native plant species, Stipa Ichu and Cortaderia Nitida, were used. Results show that Au was recovery around 19% (1.52 mg/Kg) and 25.43% (1.78 mg/Kg) by using Stipa Ichu and Cortadeira Nitida, respectively. Besides, Ag had a better recovery in the Stipa Ichu reaching a value of 6.83% (0.628 mg/Kg); in contrast, Cortadeira Nitida had an efficiency of 3.6% (0.814 mg/Kg). Bioaccumulation, bioconcentration and translocation factors were calculated by determining the concentration of precious metals in the roots and aerial parts of each plant. Results show that Stipa Ichu had a greater capacity of hyperaccumulated Ag compared to Au; while Cortaderia Nitida tended to have a better performance for Au. In conclusion, both plants are recommended for phytoremediation of mining liabilities.

Feb 1, 2023

By C. M. Bartley

Canada has been a producer of sulphur in various forms for about 100 years, Pyrites, as a source of sulphur dioxide for the manufacture of sulphuric acid, were being mined in the 1860's. Smelter gas, for the same purpose, has been recovered since 1928. Between 1935 and 1943, and from 1952 to the present, elemental sulphur has been produced in Canada from two raw material sources and by several methods. This paper attempts to present a view of the current status of the elemental sulphur industry in Canada based on the sour gas fields of Alberta and British Columbia. Production from this source has increased rapidly in the past 12 years to make Canada one of the major sulphur producers of the world. The present industry in Canada relies mainly on sour gas sulphur and it is expected that it will continue to grow in the future. However, before describing current activity relating to sour gas it may be of interest to outline briefly the early pyrite activities, the roots of the sulphur industry in Canada.

Jan 1, 1964

By J. B. Offei, K. Awuah-Offei

Mining companies registered with the SEC were required to comply with Regulation S-K 1300 for their annual report covering the first fiscal year ending on or after January 1, 2021. Consequently, most mining registrants filed their first S-K 1300 compliant disclosures in 2022. The US Securities & Exchange Commission (SEC), as part of its disclosure review program, has been issuing comment letters in response to these filings. This paper presents an overview of the trends in these comment letters. The authors reviewed comment letters retrieved from the SEC’s EDGAR database based on Standard Industrial Classification (SIC) Codes that cover mining, the content of the comment letter (whether it references S-K 1300 or not), the names of SEC staff listed in the comment letters, and other criteria. The analysis shows the SEC staff's reviews have been comprehensive covering the breadth of S-K 1300 and eliciting compliance with the rule. The staff through their comments are eliciting all the disclosures required by S-K 1300 and are not allowing registrants to substitute disclosures based on other standards for S-K 1300 disclosures. It is important, however, not to over generalize as the comments are based on the particular context.

Feb 1, 2023

By G. Wang, L. R. Moore, Y. Xiong, A. Gorken

"Feldspar may represent 60% of the earth’s crust, but the mineral does not exist in a pure state. It is generally associated with quartz, iron containing minerals such as mica, and titanium containing minerals such as rutile. Feldspar itself can even exist in different lattices from those containing sodium to various divalent ions. As such, its beneficiation has become a process that is quite complicated, when compared to the beneficiation of other minerals. It is this complexity that has made feldspar beneficiation dependent on tailor made reagents to successfully yield the industry specified feldspar products. This paper reviews the mineralogical variations found from two feldspar mines and the development of collectors to specifically target a Fe+Ti concentration of < 0.05%, while maintaining a feldspar recovery greater than 90%.INTRODUCTION Feldspar is a class of aluminum silicates that represents the most abundant mineral on earth (Vidyadhar, 2002). This class of mineral can further be defined by the types or concentrations of cations present in the crystal lattice, MAlSi3O8 (M = K, orthoclase and microcline; M = Na, Albite; M = Ca, Anorthite) (Heyes, 2012). Feldspar is most commonly mined and processed for either the alumina used in glass making or for the alkalis used in ceramics. The alumina is known to improve product hardness, durability, and resistance to chemical corrosion. The alkalis act as flux, which means they not only lower the melting temperature of the mineral mixture, but also assist in connecting the other components present in ceramics. It was stated in 2009 that the world production of feldspar was in excess of 18.3 million tons produced, with the majority coming from China, Italy, and Turkey. Raw feldspar is typically found with quartz, iron containing minerals such as mica, titanium containing minerals such as rutile, and other feldspar minerals (Celik, 2001). Quartz is stated as having a negative effect on the melting point of the feldspar, whilst the iron and titanium based mineral contaminants are known to have negative effects on color and quality of the product produced; these mineral contaminants must therefore be separated prior to application (Barns, 1997 & Celik, 2001). Mineral flotation and magnetic separation are the most common means of feldspar beneficiation. However, conditions vary greatly from mineral contaminant to mineral contaminant (Table 1). Some literature suggests feldspar can be floated with an amine, but this generally yields lower than acceptable recoveries and often still requires the magnetic separation of iron based minerals to achieve the desired grade (Amarante, 1997 & Heyes, 2012). Feldspar flotation can be further improved with the addition of hydrofluoric acid (HF) as a silica depressant and feldspar surface modifier, but this still requires the removal of some of the other minerals first. Rutile can be floated with an anionic fatty acid collector at a pH range of 7-8 or with a petroleum sulfonate at a pH < 4 (Celik, 2001), while mica can be floated with a petroleum sulfonate or an amine collector at a pH of 3.5."

Jan 1, 2016

By Thomas J. Wright

The evaluation and development of the Eastern North Carolina phosphate deposit resulted in one of the world&apos;s largest and most modern phosphate mines and fertilizer complexes at an investment in excess of $90,000,000. The resulting ore beneficiation process showed excellent correlation with pilot plant data. A number of variations from current industrial practices were introduced and projected from bench scale tests through pilot plant to production. Principal among these variations were the following: 1) removal of magnesium by classification, 2) simultaneous flotation of coarse and fine phosphate, 3) the use of saponified fatty acid, 4) utilization of filter wash water for deoiling, 5) utilization of a rougher concentrate for acidulation, 6) calcination of flotation concentrates, and 7) elimination of grinding prior to the manufacture of phosphoric acid.

Jan 1, 1971

By W. K. Dressel

Over 2 million tons of steel furnace dusts are produced each year in the United States. Recycling of these dusts rather than disposal would conserve mineral resources, reduce land requirements for disposal, and decrease pollution. In addition to the iron content, the dusts contain appreciable amounts of zinc and lead. Removal of lead and zinc with simultaneous reduction of Iron oxide has been achieved by inert atmosphere roasting of carbon-containing pellets prepared from steel furnace wastes. High- and low-carbon wastes were blended to obtain mixtures with sufficient carbon to serve as a reductant during subsequent roasting. The mixtures were pelletized with the addition of bentonite and water, and the dried pellets were roasted in a stream of nitrogen at temperatures ranging from 900" to 1,150° C. Zinc and lead contents were reduced to the 0.1 percent level or less by roasting mixtures containing as little as 7 percent carbon for 1 hour at 1,100° C. ton metallization increases with available carbon content; 50 percent metallization is achieved with 7 percent carbon, 85 percent metallization with 12.5 percent carbon, and over 95 percent metallization when the pelletized mixtures contained in excess of 20 percent carbon.

Jan 1, 1973

By P. A. Cornejo

Blastings always generates induced vibrations through seismic wave, these are lost energy from the blasting and therefore causing the disturbance of slopes and structures near the blast source. Most of the components of an open pit mine have to reach a physical stability, especially during its closure process. Aiming to develop a vibration prediction model using the historical records from an open pit mine located on Peru, this research has two main focuses depending on the distance from the blast source to the structure: to protect the final slopes and to protect the villagers houses. Both are based on the Devine model of the Square Root Scaled Distance (SRSD) to predict the Peak Particle Velocity (PPV). The Mid field model, where is found mainly final slopes from the pit, limited by the failure criteria of McKenzie based on the geo mechanical properties of the rock mass. The Far field model ranges distances where are located the most community households, limited by the German rule DIN 4150 for highly sensitive structures. Both scenarios resulted on a distribution abacus to limit the weight of used explosives to get the best operational advantage and structure safety.

Mar 2, 2022

By Lawrence K. Nordell

The selection of belt conveyor drive systems (*) is the subject of ongoing investigation. Frequently this choice has been governed by an incomplete perspective on the major considerations. A more comprehensive and objective approach is desirable. This paper presents additional factors which hopefully will broaden this perspective. BACKGROUND Conventional belt conveyors are powered by electric or electro-mechanical drives(*) mounted at the conveyor&apos;s head, tail, intermediate return span, or a combination of these (Fig. 1). A list of the drives reviewed is given in Table I. The following are main elements influencing the selection of the drive system: 1) dynamic characteristics, 2) economic factors such as capital cost, plant spares compatibility, reliability, availability, maintainability, and 3) environmental constraints. The principal dynamic characteristics of concern are the reactions of belt forces generated by the drive system during starting of the conveyor. Another attribute for consideration is the application of multiple driven pulleys used to 1) lower the conveyor&apos;s belt tension requirements, 2) increase the expected tonnage throughput, allowing for possible drive component failures, and 3) increase the plant spares flexibility related to the drive assembly.

Jan 1, 1977

By Bob Katsiouleris

Having passed through the worst of times for industrial minerals demand, there are signs that the best of times lie ahead. If the downturn was the result of unsustainable economic policy, the path forward has everything to do with sustain-ably meeting the demands of more people enjoying higher standards of living than ever before. Minerals producers must be poised to understand and meet their requirements well into the next decade. Successfully marketing industrial minerals - the building blocks of a growing and increasingly urban world population - will depend on producers? ability to respond nimbly to a rapidly changing and regionally evolving macroeconomic environment. A renewed focus on energy conservation, sustainable agriculture and building practices and consumer demand for products with a smaller environmental footprint will drive product and market segmentation strategies. These trends will not only shape the way industrial minerals producers do business, but also the type of skills and people they will require to run those businesses.

Jan 1, 2011

By B. K. Parekh, R. H. Mehta

Handling of fine coal is an importance issue for coal as well as the utility industry. Reconstitution in form of pellet or briquet would be desirable if it could be done economically. This paper evaluates the effectiveness of three binders e.g., asphalt- emulsion, corn starch and Brewex, in forming pellets of ultra-fine clean coal. It was found that asphalt emulsion and corn starch were not effective binders for ultra-fine clean coal, however, Brewex provided excellent quality of pellets, which exceeded all the minimum quasi requirements of coal pellets. INTRODUCTION Advanced coal preparation techniques (physical or chemical) are designed to process ultra-fine (minus 200 mesh or 74 pm) coal. The average particle size of the clean coal product is about 25 pm. Currently available dewatering techniques are effective in providing a 25 to 30 percent moisture product of this size coal slurry (Parekh et al. 1989). Handling and utilization of this dewatered ultra-fine size coal is difficult. Reconstitution, which includes pelletization, briquetting, extrusion, etc., of the dewatered coal product provides an ideal answer to handling and transportation problems. However, reconstitution of fines in the coal industry has not been successful due to various reasons. The most important criterion for its unsuccessful application in the coal industry is the cost of the binder (Capes et al. 1965). Various methods of reconstitution, such as briquetting, disk pelletization, extrusion pelletization and roller and die-pelletization, have been tested for fine coal agglomeration (Conkle et al., 1991) (Richards, 1990). Conkle et al., (1992) have provided a detail analysis of each technique in terms of moisture and operating cost requirements. According to Conkle, briquetting requires a product containing very low moisture, whereas pelletization can be done with coal containing up to 30 percent moisture. Currently available dewatering technique provides about 25 percent moisture product, thus, pelletization appears to be an ideal route for reconstitution. In this paper, results are presented on the comparison of three different binders i.e., asphalt-emulsion, corn starch and Brewers condensed solids (BCS or Brewex), for fine coal pelletization.

Jan 1, 1995

By S. Vivek

An atomic force microscope (AFM) was used to measure the surface forces between silica plate and glass sphere in sodium oleate solutions. Hydrophobic forces were observed when the two surfaces were activated by CaOH+ or MgOH+ ions. The force measurements conducted in the absence of the surfactant showed that the activated silica surfaces do not exhibit the primary hydration forces that have been observed between unactivated surfaces. The activation mechanism was studied by calculating the contributions from electrostatic and chemical interactions to the total free energy change. The results suggest that the adsorption of the hydroxo-complexes is controlled mainly by the lateral interactions between the adsorbed species on the silica surface.

Jan 1, 1999

By Robert A. Cummings

A field inventory was made of the mineral, geologic, geothermal, and groundwater resources of three geologically recent lava fields in the desert of Oregon. The term "resource" was applied with care: a "resource" must have particular value or worth, although it need not be economically viable. The spectacular volcanic features of the area have particular scientific and general interest and thus constitute geologic resources. The mineral endowment, mostly occurrences of low unit value such as stone and cinders, in large part are not resources, due to market conditions, regulations, and other factors. These and other conclusions will be used by the Bureau of Land Management in its multiple land use planning process for the area.

Jan 1, 1980

By Yi Luo, Jianwei Cheng, Mingming Li, Lei Xiao

Concealed thermal events in longwall gobs present safety hazards for underground coal miners and can significantly interrupt mining production. The probable causes for such thermal events range from coal oxidation at slightly above ambient temperature to smoldering fires due to spontaneous combustion of the broken coal left in the gobs. Locating such “hot spots” is the key step for planning and implementing mitigation measures to bring such thermal events under control. If a mine section, or even an entire mine, has to be sealed, understanding the status of the sealed mine atmosphere is important for the decisions guiding subsequent actions. The gas composition data obtained through the tube bundle mine atmospheric monitoring system is firsthand information of great value. Fire ratios proposed by various researchers and derived from gas composition data are useful in determining the fire status and even approximating the source locations (Timko and Derick, 2006). However, the applicability of each of these ratios under particular conditions should be carefully evaluated. The use of properly combined fire ratios can enhance the certainty of analysis. The explosibility of a sealed mine atmosphere deserves primary concern for safety reasons during seal construction, idle time and reopening of the sealed area.Mine atmospheric monitoring data from a longwall mine with flame fire have been analyzed. Efforts have been made to identify the possible causes, locations and statuses of these events using the obtained gas data, as well as other ventilation, geological and mining parameters. The effect of injected inert gas to control the events has also been quantified. The explosibility of the sealed atmosphere has been determined using two methods.

Jan 1, 2012

By J. G. Asbury

Broadly conceived, the demand for electricity depends upon three sets of variables: (i) the growths of the many individual demands for energy services; (ii) the competitiveness of electrically driven technologies in meeting these demands; and (iii) the energy-conversion efficiencies of installed electrical technologies. The first set of variables establishes the size of the potential market; the second, the market penetration of electrical equipment; and the third, the quantity of electricity required to operate the equipment. All forecasts of electricity consumption ultimately depend upon inferred or assumed relationships to describe the future behavior of these variables. This partitioning of the demand-forecasting problem is conceptually useful and will guide the discussion presented in this paper. However, it is also something of an oversimplification. Examined in more detail, the electricity fore-casting problem is exceedingly complex. The variables mentioned above are, in turn, found to depend upon more fundamental sets of demographic technological, resource, and policy variables. The demand projections developed by the major forecasting services are usually developed in terms of these underlying variables, which themselves must be independently forecast.

Jan 1, 1985

By Mostafa Benzaazoua, Mariam El Adnani, My Ahmed Boumehdi, Rachid Hakkou, Salah Ouhamdouch, Abdelmalek Goumih

This study focuses on the environmental characterization and assessment of long-term neutral mine drainage (CND) potential from waste rock piles at the abandoned Erdouz mine in Morocco. The study involved metallographic analysis, static tests, and column tests. Results indicate that the waste rock is not an acid mine drainage generator but produces CND, mainly with sulfates exceeding Moroccan standards. The waste rock is relatively stable and could be reused after pretreatment.

Jan 25, 2022

By Yves C. Lizotte

Although blasting remains the most inexpensive method of fragmentation in hardrock mining, the significance of the costs of blast-induced rockmass damage in terms of mining efficiency and safety is becoming increasingly recognized. There is no straightforward and systematic method of adequately measuring blast damage in on-going mining operations. This paper considers various techniques available to measure blast damage, making particular reference to recent underground hardrock mine studies. It concludes by proposing a damage audit procedure for integration into routine mine production control.

Jan 1, 1996

By C. W. Baxter

Eveleth taconite company was formed in 1963 to mine and beneficiate taconite on the Mesabi range of Minnesota. Its thunderbird mine is located midway between the cities of Eveleth and Virginia, Minnesota, and the crude ore is transported by rail to its Fairlane plant approximately ten miles to the south of the mine, "figure 1". As is implied by the names of the mine and plant, the ford motor company is the principal owner of Eveleth taconite company, with an 85% interest, Oglebay Norton company holds the remaining 15% interest and also is the managing agent.

Jan 1, 1972

By M. Deutsch

A common casualty of modern open pit mine optimization is the assurance that the resulting design is actually achievable. Optimized mine plans that consider value and a bare minimum of precedence constraints do not, in general, translate into practical, operational mine designs that can really be used in the field. Ultimate pits may come to a sharp point at the bottom. Schedules may require taking small parcels of material from many disparate areas of the pit in a single period. And grade control polygons may be ragged, narrow, and not minable with realistic equipment. In this paper all of these problems are addressed by encoding these three fundamental open pit mine optimization problems as maximum satisfiability problems. Maximum satisfiability provides a useful framework for problems that are non-linear and may guarantee the optimality that metaheuristics cannot. INTRODUCTION Open pit mines are large and complicated operations, which require significant initial and ongoing investment. A single mine may employ hundreds or thousands of people and creates substantial benefits for both the surrounding and global communities. Planning an operation of this magnitude requires a lot of effort and cannot be done optimally by hand. Mining engineers today rely on many techniques from operations research to guide decision making, and to maximize the value of the mine. Techniques including linear programming, metaheuristics, and network algorithms are all used to solve different problems throughout mine design and optimization. However, techniques based on Boolean satisfiability, including the optimization extension of maximum satisfiability, have not seen much use in mining despite being used in many other fields including electronics design, scheduling, and artificial intelligence. We claim that maximum satisfiability is a useful and meaningful way of expressing and solving optimization problems in mine planning. However, this technique does not come without challenges; the problem is NP-hard, and modern techniques for solving these problems can struggle with the number of variables and clauses that a typical mining problem requires. Also, some of the constraints that mining must contend with do not fit nicely into the satisfiability paradigm. Despite these challenges, we believe that maximum satisfiability provides a useful framework for considering operational constraints and expressing some problems that other techniques can't easily express. Maximum satisfiability can be solved exactly, yielding the true optimal answer which metaheuristics cannot guarantee. In this paper we show the applicability of maximum satisfiability to mining by specifying three fundamental problems in open pit mine optimization. We show how these fundamental problems can be formulated and how they can be extended within the framework of maximum satisfiability. For the remainder of the paper we first give a brief background on common elements between the three problems and an introduction to satisfiability. Then we tackle the three problems; the Ultimate Pit Problem, the Block Scheduling Problem, and the Grade Control Polygon Problem. In the Ultimate Pit Problem we specifically show how to extend the problem to support a minimum mining width – a coveted result for many mining engineers. We then discuss some of the complexities and shortcomings of this framework and possible research directions.

Jan 1, 2019

By W. Burger

For the development of deep, hard rock, mines fast access to the orebody is critical. In some cases the mineralized area is more than 1,500 m (5,000 ft) below surface. Excavation of shafts or declines is typically on the critical path of the project schedule. Saving time on those activities can significantly increase the net present value of the mining project. Mechanical excavation methods are a step-change in excavation performance and labor safety compared to drill-and-blast operations. In hard rock conditions, roadheaders cannot be used effectively, so disc cutting is the first choice. For excavation of declines, tunnel boring machines (TBM) can be used in many cases. These provide, in certain rock conditions, considerably higher production rates com-pared to drill-and-blast excavation. Herrenknecht AG has developed a vertical shaft sinking machine (VSM) that is able to excavate shallow shafts in soil and medium soft rock. The ground is excavated by a roadheader boom. The muck is removed by a slurry system or a pneumatic system in combination with hoisting of skips. These machines have been applied successfully on shafts down to 100 m (300 ft). A pre-sink for a deep mine shaft has been excavated by this technology. For deep, hard rock shafts, a new shaft boring system has been developed by Herrenknecht AG in collaboration with Rio Tinto. Based on proven technologies, the system uses a unique arrangement of existing proven technologies. The system integrates excavation, mucking, primary rock support, installation of the final lining and shaft infrastructure. This new system improves the health and safety of shaft construction. Detailed performance estimates indicate significantly higher shaft construction rates are possible compared to conventional shaft sinking methods.

Jun 1, 2010