Search Documents

By G. E. Rouse

Anomalies of sulfur dioxide and other gases have been defined, by direct measurement, around various sulfide bodies. These readings were made (1) in soil gas and (2) in the atmosphere, from both ground vehicles and, to a limited extent, from helicopters. Test areas included porphyry copper and molybdenum deposits, sulfide bearing vein systems, pyrite zones associated with sandstone uranium accumulations, and pyrite-bearing mine dumps. Some of the deposits are covered by as much as several hundred feet of overburden or barren rock, while others outcrop, or have been exposed by mining operations. Depending on local conditions, background values of sulfur dioxide in soil gas and the atmosphere range from 1 to 15 parts per billion. Using present techniques, anomalous readings are recognized at approximately two times background. Apparent "depth penetration? on known deposits has ranged to several hundred feet. Readings have been made over known deposits from a helicopter and ground vehicle moving at up to 40 mph. The rate at which the survey may be carried out depends largely on the size and extent of the anomaly. The existence and magnitude of sulfur dioxide anomalies around sulfide-bearing deposits is a function of geology, target size, soil moisture, and climatic conditions such as temperature and temperature changes, barometric pressure, wind velocity, and precipitation. Industrial S02 pollution can effectively mask the presence of the anomalies sought.

Jan 1, 1971

By Ziyan Ouyang, Haotian Zheng, Spencer Quiel, Mike Mooney, Clay Naito

This paper summarizes the results of an experimental program conducted to characterize the moment-rotation behavior of skewed flat radial joints from large diameter (45 ft) tunnel lining. Both positive and negative joint moment-rotation behaviors were measured experimentally using two-segment joint combination assemblies. The results are compared to closed form methodologies used by designers, e.g., the Janssen method. The differences in observed and model behavior are discussed within the context of design practice.

Jun 23, 2024

By A. L. Stomberg

Federal and State surface coal mining regulations require special handling of prime soil materials which result in additional costs, and no actual benefit when prime and non-prime soils are similar. The Coteau Properties Company proposes to mix both prime and non-prime topsoil and subsoils at the Freedom Mine in Mercer County, North Dakota, based on an analysis of soil physical and chemical characteristics which show these materials to be comparable.

Jan 1, 1985

By Jack C. Haptonstall

The Tayoltita Unit of Minas de San Luis, S. A. is situated in an isolated corner of the state of Durango, Mexico. The ore deposits in the region were first worked by Indians, but by 1757 the Spaniards had discovered them, and the first systematic exploitation of the mines commenced. By the early 1900's most of the mines had been acquired by American interests, and the San Luis Mining Company was organized. The modern period of exploitation, uninterrupted for the last 74 years, began. In 1962 the company was fully "Mexicenized" in compliance with the modification of the mining law, and the name was changed to Minas de San Luis, S. A. Tayoltita continues as one of Mexico's most important silver and gold mines. The ore is extracted in en extensive underground operation, mining epithermal fissure veins by selective methods. The ore is milled and treated in an efficient counter-current cyanide plant, where 95 % of the silver and 96 % of the gold is recovered. Current annual bullion output is 55,000 kg (1.7 million troy oz) of silver and 1000 kg (31,000 troy oz) of gold from milling 165,000 try (181,900 stpy). Rough, 33-kg (1000-troy oz) bullion bars are smelted at the mine, shipped by air to Mazatlan, Sinaloa, and are thence sold to the Met- Mex Peñoles smelter in Torreon, Coahuila. Ore reserves, blocked by very conservative methods, are currently at 540,000 tons (595,000 st). Ore reserve grade is 425 g of silver and 6 g of gold per ton (12.4 troy oz Ag and 0.18 troy oz Au per st).

Jan 1, 1976

By J. S. Gardner

Fortunately, few mining professionals have dealt with what all mining professionals fear---a mine disaster. Unfortunately, many have dealt with ?accidents? which may or may not claim lives but nevertheless rise to the level of a ?disaster? given the fallout of liability and litigation in today?s society.1 The undersigned authors published an article some ten years ago regarding crisis management2 based upon their collective first-hand experiences in actual disasters to that point in history. Unfortunately, disasters have occurred since that time, prompting legislation, and a fresh analysis and expansion of those basic principles is certainly in order. Without question, no two disasters are ever alike, yet general guidelines for forming an effective plan of action can be formulated?and if a mining operation is to have any chance of survival after a disaster, such a plan is vital. The primary concern as any disaster evolves remains as stated a 2003 SME article3--the protection of human life. From that point, the focus moves to any assistance that may be needed given the magnitude of the situation. Permeating throughout this process is "damage control." The first step in dealing with a disaster, however, begins long before any threat of danger arises?formulation and implementation of an Emergency Response Plan.

Feb 23, 2014

By James S. Browning

Extensive deposits of kyanite occur in the southeastern United States, The reserves of these deposits, if developed, are adequate to supply the United States with 35-mesh kyanite concentrate:; for many years at the present-rate of consumption, According to Espenshade and Potter,1 the kyanite-quartz rock type deposits in this area contain about 100 million tons of ore averaging 10 to 30 percent kyanite. The tonnage of kyanite-bearing gneiss and schist is, much larger than the tonnage of kyanite-quartz rock, but the kyanite gneiss and schist are appreciably lower in grade. The largest deposits of kyanite-quartz rock are in the Farmville district, Virginia, and Kings Mountain district, North Carolina South Carolina, and at Graves Mountain, Georgia. Of the known deposits, only four were being mined for kyanite in 1967. These deposits are near Farmville and Dillwyn, Va., Clover S. C., and Washington, Ga. Production of kyanite and synthetic mullite increased substantially in 1965.2 Output of, domestic kyanite concentrate increased by 14 percent in 1965, establishing a record high for the fifth consecutive year. Estimated annual consumption of kyanite minerals and synthetic mullite was in excess of 100,000 tons. The manufacture of mulatto refractories accounts for most of the kyanite minerals consumed annually, but non-refractory uses are expanding.3 Most mullite refractories are used as furnace linings in metallurgical and glass manufacturing furnaces. The remainder is used largely for kilns, kiln furniture, and saggers by the ceramic industry. Small quantities of kyanite without calcination are used as a source of alumina in the manufacture of glass, electrical and chemical, porcelain, pyrometer tubes, and in the form of kyanite concentrate to increase the alumina content of fireclays. Kyanite is used to improve workability, increase strength, and to compensate for firing shrinkage in floor and wall tile and other ceramic products.

Jan 1, 1968

By G. Southam

Bacterial populations play an active role in mineral weathering in subsurface and near-surface environments e.g., supergene enrichment of Cu at Morenci, AZ. An in vitro bacterial biofilm model was used to examine the interaction between Sporosarcina ureae and ionic gold (which is toxic) or amino acid-gold complexes in gold mobility. The immobilization of ionic gold was between 80-90% for 1 week but as the available, cellular reactive sites became saturated immobilization decreased to 14% within 2 weeks. In the asparagine-gold system, gold immobilization occurred at a high rate (80-90%) throughout the experiment with limited toxicity towards Sporosarcina ureae.

Jan 1, 1999

By Ray E. Williamson

One of the prime objectives of the mine industry is to develop a low cost way to clean up what has been called "The Rape Of Mother Nature". The project falls under the broad umbrella of reclamation, which is now considered an essential part of the mining cycle. As such, it is being given full consideration in the initial planning of all surface operations. In most areas, if a proposed mining system does not lend itself to proper reclamation, it is not an acceptable system. By combining mining and reclamation plans, a producer not only can minimize reclamation costs, but can also restore the land to usefulness and insure continuing profits after a deposit is depleted. As long as fifteen years ago, many of the larger mining companies were already deeply involved in this extra cost work. Even then the involved companies were projecting a great need for a bigger bulldozer, Bigger than anything commercially available. At that time, the D9 tractor weighed about 60,000# bare weight.

Jan 1, 1975

By G. C. Presley

With plant construction scheduled for the Spring of 1997, U. S. Zeolites will become the new source for quality in natural zeolites. The company will selectively mine, dry process, package, and market a very high quality clinoptilolite possessing many unusual properties. These unusual chemical and physical properties provide a multitude of industrial, commercial, and consumer applications. Extensive testing has determined many potential applications.

Jan 1, 1997

By E. A. Domínguez

La Espingarda kaolin deposit was formed by ?in situ? alteration of volcaniclastic rhyolitic rocks belonging to Jurassic Marifil Formation. Three volcanic lithofacies were identified: porphyric biotitic ignimbrites (PBI), a coarse lithic ignimbrite (ILG), a fluidal intrusive rhyolite (RFI), all kaolinized in different degrees. The alteration covers an ellipsoidal area of ~20,000 m2, with its alteration decreasing downwards and disappearing at 8-12 m from the surface. The length to thickness ratio of alteration is 60:1. An erratic silicification was found as small zones (<3 m2) of quartz stockwork. The mineralogy is kaolinite + quartz + feldspars + Fe-oxyhydroxides ± halloysite ± illite and interstratified I/S, although the relative proportions change in each rock type. Due to coarse grain size and high quartz content, natural kaolin is unsuitable for slip cast ceramics, unless beneficiated. Washed ILG kaolin has the best rheological properties and behavior in casting and drying for its mineralogy, particle size distribution, thin texture and surface activity, as well as a certain fusibility and firing kinetics. PBI and RFI kaolins, due to finer texture, smaller grain size, lower surface activity, and higher halloysite amount, have worse slip viscosity and thixotropy that are due also to soluble salts. For the same reason, they have good casting and drying properties, but their purity brings about higher softening temperatures and water absorption. Several parameters are used to discriminate between hypogene or supergene kaolinite genesis. The hydrothermal genesis is mainly sustained by fluid inclusion temperature (150-180ºC) in quartz veinlets, while weathering is supported by deposit morphology, simple mineralogy, kaolinite stable isotopes (d18O ? 18, 13; dD ? ?59; ?85) and paleoclimatic record. It is concluded that a weathering process formed the main alteration with some participation of steam-heated meteoric waters. Neither the contents of Au, Ag, As, Sb, Hg, nor drill data support the existence of any epithermal gold mineralization at the kaolinite bottom.

Jan 1, 2010

By M. M. Hajdasinki

A project&apos;s rates of return (RORs)1, be it the internal rates return (IRRs) or one of the many IRR surrogates, frequently needs to be approximated. The success and efficiency an ROR- approximation procedure depend on the quality the approximation-initiating parameters, such as bounds or seed values (guesses). The existing approximation procedures commonly use bounds and guesses suggested by intuition rather than supported by mathematical considerations. This paper presents three mathematically founded ROR-bounding and eleven ROR-guessing approaches and examines their suitability by using examples of typical project cash-flowpatterns (CFPs). The calculated bounds and guesses not only improve the approximation efficiency, but also allow the process of the ROR discovery to be automated, thereby making it more convenient and reliable.

Jan 1, 1999

By J. B. Hiskey

The principle oxide minerals of molybdenum are wulfenite (PbMoO4), ferrimolybdite (Fe2(MOO 4)3.nH2O), powellite (CaMoO4), and ilsemannite (Mo304). Wulfenite is found in Arizona, New Mexico, Nevada, Utah, California, and Montana. It is also found in the states of Sonora and Chihuahua, Mexico. Prior to 1915 wulfenite ores were the primary source of molybdenum. The solubility of wulfenite in hot sodium sulfide was first noted by Bonardi(1) during attempts to sulfidize wulfenite material prior to flotation. He identified lead sulfide and soluble sodium molybdate as reaction products. Bacon (2) sulfidized wulfenite in preparation for flotation and by X-ray analysis found the reaction product to be lead sulfide. Holmes(3) made an extensive investigation of the extraction of molybdenum from wulfenite concentrates by leaching. Nearly 100% molybdenum extraction was possible from -100 mesh samples leached for 15 min with 10% sodium sulfide solution at room temperature. Molybdenum extraction from -100 mesh samples after leaching 30 min at a temperature of 45°C using 2, 4, and 6% sodium sulfide was about 32, 79, and 98% respectively. The extraction showed little sensitivity to time, temperature, or particle size using 10" sodium sulfide solution.

Jan 1, 1976

By Stanley R. Riggs

The rocks exposed in the phosphate district are of Neogene age and consist of clayey quartz and phosphorite sands overlying phosphatic dolomite. The Bone Valley Formation is redefined as a marine phosphorite containing primary phosphorite and abundant terrigenous sediments. It contains a Middle Miocene vertebrate and invertebrate fauna and conformably overlies the Hawthorn Formation containing similar invertebrate fauna. A new, unnamed formation, with Pliocene and Pleistocene fauna and containing reworked phosphorite, overlies the Bone Valley disconformably. Its phosphorite is derived from the subjacent Bone Valley by post-Middle Miocene erosion and deposition in stream channels and marginal marine environments. The Bone Valley contains two main types of primary marine phosphorite. Orthocbemical phosphorite, a direct precipitate of microcrystalline phosphorite (microsphorite), occurs as a cement or binder in thin beds. Allochemical phosphorite consists of clastic phosphorite particles that were originally formed as microsphorite on another part of the shelf. Microsphorite was deposited in a very shallow open marine environment which had an abnormally high phosphorous content caused by upwelling currents. The mechanism of deposition is still in doubt, but organisms probably were a major factor. Soon after deposition, microsphorite was indurated, periodically torn up, and the resulting fragments transported and deposited elsewhere on the shelf. These processes account for a great portion of the clastic phosphorite in the Miocene deposits of Florida. The primary fossil skeletal material is of minor importance.

Jan 1, 1965

By A. J. Guse

The primary limiting factor for hoisting capacity from great depths is the self-weight of steel wire ropes. Steel wire ropes are very suitable for mine hoisting due to their high strength and durability, but have the negative characteristic of a low strength/weight ratio. Also, as hoisting depths increase, the service life of steel wire ropes decreases due to the higher stresses and physical effects on the ropes. The significantly higher strength/weight ratio of synthetic ropes offers the primary advantage of hoisting a larger payload with a similar size rope and hoisting plant. The beneficial properties of synthetic ropes could be used to improve the overall economics of deep underground mining both for new deep shaft projects and for existing mining operations expanding to deeper orebodies. A research and development program has been initiated to evaluate the suitability of a fully synthetic rope for the mine hoisting application.

Feb 23, 2014

By Andrew Chegwidden, Tara Wilk

Construction of Shaft 17B-1, a part of The New York City water supply system, required an excavation of approximately 38 m (123 ft) through water-bearing overburden soil and more than 152 m (500 ft) of gneiss bedrock to make a connection to Water Tunnel No. 3. Ground freezing was the specified method to provide temporary earth support and ground water control for the overburden material. The ground freezing process relied on a supplemental geotechnical investigation and comprehensive laboratory testing of the frozen soil to evaluate the potential long-term creep behavior of the soil and the elimination of a temporary lining system. This paper describes that process as well as the drilling and installation methods of the ground freezing system. Additionally, the methodical system of excavation and insulation is discussed that permitted a safe and timely excavation followed by the installation of the permanent concrete liner.

Jun 13, 2023

By C. C. Clark, S. J. Jung

Determining the correct combination of mix components and water for high-density paste backfills that have the transport and deposition properties necessary for a mining operation is a difficult task. Rheologic properties cannot be determined without conducting full-scale pumping tests, and data from existing tests tire very limited. This paper presents the findings of investigations undertaken to determine if paste-backfill rheology can be determined using existing techniques and to determine which mix and system variables have the greatest influence on transport-pressure loss. Data from laboratory-scale pumping tests were used to produce a rheologic model of flow behavior for comparison, and a statistical analysis was conducted to determine the most significant factors affecting transport-pressure loss.

Jan 1, 1996

By A. J. S. Spearing, B. Forbes, T. Kostecki, A. Hyett

Improving upon the past understanding of the interaction between installed rock bolts, the immediate roof and sidewalls is vital for the implementation of sound support system design, as this has a direct impact on rock-related safety. This is the primary goal in rock-bolt-related research. The earliest research in this field concentrated on limited laboratory and in situ measurements accompanied by theoretical analyses, based on the Kirsch equations. This represented the initial insight into understanding relative ground movements and their impact on primary support. However, these studies were far from complete. More recently, major technological advances in computing power within the mining industry has changed the scope from theoretical analysis to computer simulation. Even with these advancements our understanding of rock bolts in situ and in the laboratory has not progressed, particularly concerning bending and shear. To measure the behavior of rock bolts, the widely accepted practice is to populate the bolts with an array of strain gauges. Historically, resistive foil strain gauges or long displacement sensors have been used. Additionally, all instrumented rock bolts have used only two diametrically opposed slots. Rock bolts instrumented with these methods have significant shortcomings, one of which is the inability to capture shear and bending. The shearing and bending of rock bolts are particularly common in tabular soft rock mining, such as coal mining. This paper discusses the use of three slotted rock bolts, cut diametrically 120º apart, and two new optical fiber technologies populated along the entire rock-bolt length.

Jan 1, 2015

By W. J. Kogelmann

Roadheaders, also called Boom Miners or Boom-type Tunneling Machines have been in North America since 1968, when first introduced by Willy Kogelmann, the founder of Alpine Equipment Corp. (?Alpine?). Roadheaders were invented in Europe in the late 1940s. Machines with in-line, axial cutter heads were developed in the former Soviet Union. The British Dosco DRCL is based on the Russian PK-3 roadheader. Roadheaders with transverse ?ripper? cutter heads were invented in Hungary (1). The Austrian-made Alpine Miners of VOEST-Alpine, purchased by Sandvik AB, are based on a 1965 Hungarian license. Roadheaders are widely used in the mining and tunneling industries because they can excavate drifts, entries and tunnels with cross sections of any shape and size, can handle mixed faces, work on steep grades, and negotiate tight curves and cross-cuts. A roadheader?s only major limitation is the strength and abrasiveness of rock and minerals to be excavated. This paper covers roadheader selection criteria, improvements in reliability, attachments for flexibility (Multi-Tool Miner), and automated support systems for increased cutting time for increased shift production.

Jan 1, 2008

By J. V. Belke

There are many aspects of a grinding mill supply and installation that can result in the mill not operating as intended, resulting in unplanned shutdowns, poor reliability and headaches for all concerned. One of the largest aspects, both in criticality and physical mass, is the mill foundation; if not properly specified, designed and constructed the mill operation will be compromised. The mill foundation starts with the design specification and loading diagram supplied by the mill builder. The importance of understanding these documents and how to apply them is critical for the start of any mill project. When designing mills with a GMD the foundation must be properly modeled to ensure that all interactions of the mill and motor structures, foundation and subsurface strata behave in the intended fashion. All of the previous efforts can be laid to waste if the construction of the mill foundation is poorly handled. Mill foundations are typically the most massive concrete structure at a processing plant and can easily cause nightmares for inexperienced contactors. This paper explores some of the more important facets along the lifecycle of the grinding mill foundation.

Feb 23, 2014

By William R. Yernberg

Caterpillar introduced 21 new products during Caterpillar Press Days ‘96, held in June at the company’s proving grounds near Tucson, AZ. The event, billed as the largest product introduction ever held by Caterpillar, was attended by press from around the world. Most of the new products were demonstrated at Caterpillar’s Tinaja Hills Training Center in the Sierrita Mountains south of Tucson. Under the scorching Sonora Desert sun, the press was treated to demonstrations of the new equipment. After a display of the equipment’s power and capabilities, the press was given an opportunity to operate the new models and, in some cases, compare them with the old.

Jan 1, 1996