Search Documents

By Spencer R. Titley

Porphyry copper deposits in the southwestern Pacific area represent relative newcomers to the growing number of occurrences of this mineral deposit type. In addition to firmly establishing the importance of this region and its potential influence within the framework of world copper resources, the deposits of this region are significant from a scientific point of view because of their close relationship to the phenomena of Island Arc evolution. Since the discovery of Panguna on Bougainville in 1964, the list of prospects, proven and unproven, and developments, has grown to more than twenty and the number continues to increase. At the time of this writing, the number of prospects is imperfectly known but the following localities and numbers are fair minimum approximations: Manus (Admiralty Islands) (3); New Britain (5); New Ireland (1); Guadalcanal (2); New Guinea Highlands (6); Misima (1); and Fiji (2); Proven prospects are present in the new Guinea Highlands (2); one deposit is being developed in Test Irian, and one orebody, on Bougainville, is in production. This summary paper concerns a discussion of some of the geological characteristics of producers, developments, and prospects on the Islands of Nets Guinea, New Britain, Bougainville, Guadalcanal, and Manus. I am not aware of publishable data for Misima or Fiji. As so many variables ultimately determine whether or not a porphyry copper occurrence becomes an orebody, not the least of which is geography, this summary treats the characteristics of these occurrences which alloy; their assignment to the porphyry copper category. For purposes of this discussion, I have considered those copper occurrences which are apparently genetically related to talc-alkaline intrusions and in which the content of copper has been upgraded 50 to 100 times the Clarke for that particular host rock. Some of these occurrences are shown on Figure 1.

Jan 1, 1973

By Jim McKinley

With a growing number of mines reaching closure and seeing closure costs materialize, regulators, lenders, and banks are observing projects that fail economically by miscalculating these costs. Mine closure costs are often categorized as a type of liability which is defined as the money owed by the company to offset effects from the project, and the money available to pay for those debts (e.g., bond). Often, decisions made before Day 1 of mining (e.g., co-disposal, dry stack tailings, waste segregation) can significantly change the bond calculation. Once the bond is calculated and funded, operators are encouraged to conduct closure research and use applied science for progressive bond release prior to final closure. However, this author has observed few instances of financially significant progressive bond release, as there are typically no robust procedures for bond return, either before or during closure activities. As a result, many companies decide that entering a state of Care & Maintenance (C&M) is less risky than attempting to fund closure activities with an unknown bond return mechanism. Although perhaps less risky in the short-term, the primary long-term risk with entering C&M is that it increases the chances of the bond not covering the cost of closure and the chances of the government/regulatory agency inheriting the mine closure. Bonds are typically reevaluated on a regular cycle (e.g., five years) so every mining company goes through this financing challenge eventually.

Feb 22, 2026

By D. S. Parasnis

The early beginnings of mining geophysics in Sweden can be traced back to the reign of queen Kristina in the 17th century. The mine compass, consisting of a freely suspended magnetic needle in a casing, was in use certainly by 1640 and probably earlier for locating iron ore deposits. Whether the mine compass was a Swedish invention or not is an unsettled question since the possibility cannot be overlooked that the celebrated Nürnberg compass-makers of the 16th century may have constructed it for the first time(1). Be that as it may, the mine compass was very extensively employed in Sweden for more than two centuries and met with spectacular success in locating magnetic deposits under shallow overburden. Occasionally the diligent prospector would even be rewarded with a pyrrhotitebearing sulphide deposit, as witness many old sulphide-ore pits and some mines still in operation from the 17th and the 18th centuries. The mine compass measured only the orientation of the Earth's magnetic field and not its strength. Although it was improved in construction and sensitivity over the ages, no great strides were made in magnetic prospecting after the initial discovery of the use of the compass until Gauss, omnipresent in 19th century physics and mathematics, showed with the assistance of Weber how the strength of a magnetic field could be determined.

Jan 1, 1975

By A. A. El-Midany, R. M. Farag, A. M. Salem, S. E. El-Mofty

Bentonite is one of the main players in the stability of drilling mud. Its particle size and particle size distribution significantly affect drilling mud’s rheological properties. Although the Specifications for Drilling Fluids Materials report on Oil Companies Material Association (OCMA)-grade bentonite states that the API recommended powder having 2.5 percent mass fraction as the maximum value of residue of diameter greater than 75 μm, there is no other information on the specific size distribution for API bentonite. It was found that API bentonite has a specific size distribution with specific mixing weights. It is important to investigate why that mixture represents the optimum properties of drilling mud and how each individual size fraction has a specific function in the mixture. To clarify the effect of individual size as well as the collective effect of the size distribution, API bentonite was classified into different size fractions, with each tested separately for controlling properties such as filtration loss, plastic viscosity, gel strength, cake thickness and packing density.

By Ricardo D. Presnell, Erich U. Petersen, William J. Tafuri, Donald M. Hausen, Russell C. Babcock, William L. Gunter, Thomas R. Gibson, Douglas N. Halbe, Jay W. Hammitt

The Barneys Canyon orebody is a sediment-hosted disseminated gold deposit located 8 km (5 miles) north of the Bingham Canyon porphyry copper mine. Mineable oxide reserves are 8.6 million tonnes (9.5 million short tons) grading 1.64 g/tonne (0.048 oz/ton) gold. Host lithologies are carbonates and siliciclastics of the Park City and Kirkman-Diamond Creek Formations of Lower Permian age. Gold distributions are controlled by favorable stratigraphic units and associated alteration, and structures. Dominant alteration is decalcification and bleaching of carbonates, and argillization and bleaching of sandstones. Gold to silver ratios are greater than 1:1. Anomalous trace metals include arsenic, antimony, mercury and thallium. The Melco deposit lies 2.4 km (1.5 miles) southwest of the Barneys Canyon deposit. It is spatially associated with a steeply northwest-dipping siliciclastic breccia in the Kirkman-Diamond Creek Formation at the contact with underlying orthoquartzites of the Freeman Peak Formation. Both gold-bearing oxidized and sulfide lithologies are present, often in sharp contact. Mineable oxide reserves are 2.8 million tonnes (3.1 million short tons) grading 2.40 g/tonne (0.07 oz/ton) gold. Anomolous trace metals include arsenic, antimony, mercury and thallium, which are generally present in concentrations greater than those at Barneys Canyon, particularly in sulfide-bearing material. A spatial, temporal and genetic relationship is proposed between the Melco deposit and late-stage gold mineralization at Bingham Canyon, although both the Melco and Barneys Canyon deposits have many similarities to Carlin-type gold deposits.

Jan 1, 1990

By Shangyong Lin, Wei Sun, Weiping Liu, Muhammad Azam, Junfeng Cheng, Yujie Zhao, David Asubonteng, Michael Ngoie

Copper concentrates have wide application in global smelting operations, comprising primarily of chalcopyrite (CuFeS2) as the principal mineral, accompanied by chalcocite (Cu2S) and bornite (Cu5FeS4) as secondary copper-bearing minerals. However, these concentrates frequently harbor detrimental impurities, notably fluorine ions, which can cause various complications during the smelting process. Moreover, an elevated fluorine content in copper concentrates may entail financial penalties and sales constraints. This review conducts a comprehensive analysis of existing methods for the removal of fluorine, presenting a nuanced assessment of their merits and demerits. It also provides valuable insights into the current landscape of fluorine elimination from copper concentrates and pinpoints pivotal areas warranting future investigation. This review endeavors to serve as a pragmatic resource for researchers and industry professionals operating within this domain.

Jan 1, 2024

By D. Bahrami, G. Danko, W. Asante

"It is prudent to interpret atmospheric monitoring signals in real-time for checking the safe limits of the air conditions in underground mines. In gassy mines, such real-time evaluation increases the safety of operation. In all mines, the continuous monitoring and evaluation contribute to maintaining air conditions to be within healthy and safe limits. Signal interpretation for safety conditions in mines is difficult for many reasons. An increase of hazardous contaminant concentrations can be predicted by signal pattern recognition, root-cause analysis of rapid changes toward deterioration and forward prediction in time using algorithms and numerical models. This paper focuses on analyzing signal patterns to recognize dangerous trends as well as forward predicting the various environmental and working conditions that may affect safety in underground mines. Efficient numerical ventilation model with heat and gas contaminant simulation components is needed for the analysis of real-time atmospheric monitoring data. Computational speed enhancement methods are discussed and tested in numerical examples, using the Jacobian sensitivity matrices for signal propagation prediction. INTRODUCTION The focus area of this paper is mine safety, related to hazardous atmospheric conditions in a mine ventilation system. Improvements by recognizing safety hazards caused by heat of combustible gases or the accumulation of poisonous gases in a mine are addressed. The recognition of safety hazard by manual evaluation is difficult because of the complex nature of information and the large amount of monitored data from measurement by atmospheric sensors such as air velocity, pressure, hazardous gas contaminants and temperature. In order to recognize problem-causing trends, it is necessary to evaluate continuously individual measurement data from the Atmospheric Monitoring System (AMS) of the mine during their time-dependent variations. In addition, the combined effects of various signal trends need to be simultaneously interpreted in their cross-effects. It is very difficult to foresee the possible outcomes of intertwined signatures of various problems by continuous human observation. For example, a steady, continuous methane concentration measurement together with a sharp drop in barometric pressure from the AMS sensors may be a case for worry in future time due to pressure-induced methane increase from the coal seam or the gob (Danko et al., 2013). This future increase can be predicted by a time-dependent Ventilation Air Model (VAM) and its surrogate Air Parameter Predictor Solver (APPS) model. A calibrated VAM or APPS model can indeed predict a likely methane concentration variation in future time as a function of previous and new air pressure as well as air velocity (Danko, et. al., 2013). Such a future trend, however, cannot be seen from the raw measurement data."

Jan 1, 2017

By Mark P. Walsh

In recent years in situ leach mining has emerged as a viable technology for the recovery of uranium from strata in South Texas which contain relatively low concentrations of uranium ore. Because the ore bodies lie within groundwater aquifers, a significant determinant in the economics is the requirement that such aquifers be protected from contaminantion. Since ammonia is one of the constituents of the leach solutions now being field tested, one environ- mental problem to be resolved is the removal of ammonia at the end of mining. A second related question is the fate of the ammonia which is not removed by the restoration procedure. This paper considers the displacement and migration of ammonium in a flowing electrolyte with concomitant ion exchange. The ion exchange is an important feature since, during the solution mining phase, ammonium saturates the mineral exchange sites and must be removed from these sites. A mathematical model is used to simulate this process and the model is tested against the results of laboratory experiments. It is found that the simulations are adequate if an appropriate selection of parameters is made. The model is then used to investigate the effect of cation composition and concentration of the restoration medium as well as dispersion on the overall effectiveness of the process. It is concluded that increasing the concentration of monovalent ions in a solution containing a mixture of both monovalent and divalent ions decreases the adsorption selectivity of the divalent ions with respect to all monovalent ions including ammonium. Thus increasing the ionic concentration of a restoration fluid by increasing the concentration of a nonselectively adsorbed (with respect to ammonium) ion may have a very limited benefit. Dispersion attending the flow of fluids in a porous medium is also shown to be an important factor. The effect of dispersion can greatly reduce the benefits of having a displacing cation which is adsorbed selectively with respect to ammonium. Since dispersion increases almost linearly with fluid velocity, an optimum displacement rate may exist.

Jan 1, 1979

By Zygmunt Sadowski

Problems encountered in barite flotation from various waste materials such as spent drilling muds are likely to be closely connected with the effect of chemical additives and metal ions present either added or present as contaminants, on the flotation. Fuerstenau and Palmer (1976) have studied in detail the adsorption of multivalent cations onto oxide and silicate minerals. It was observed that the adsorption of a multivalent metal species exhibits a sharp pH dependence which is related to the formation of hydroxy complexes of the metal ions in solution. Investigations on the recovery of barite from tailings ponds and mining wastes (Sullivan and Lamot, 1981) have shown that such barite materials can contain large quantities of carbonate and silicate minerals (including clay minerals). Also iron oxide slimes can be present. From these substances cations such as Ca2+, Mg2+, Fe2+ and A13+ can potentially dissolve and be present in the aqueous phase accompanying the various minerals. These ions and their hydrolysis products can have a substantial effect on any subsequent flotation scheme. The present study investigates the effect of the noted ions on both the stability and electrokinetic behavior of barite suspensions.

Jan 1, 1986

By Robert M. Stevens

INTRODUCTION Truck haulage of muck in underground mining operations has been in use around the world for many years. From the late 1.950s into the early 1970s, haulage by means of load-haul-dump (LHD) units challenged haulage by means of trucks, and, to a large degree, LHD units dominated the trackless concept of moving mate¬rial underground. However, beginning in 1975, the emphasis began to shift back to the use of trucks, with LHD units assuming the secondary role of loading the trucks. Over the years, several manufacturers have been offering trucks with capacities ranging from 4.5 to 45.4 t (5 to 50 st) and with features that specifically address the constraints of underground operation. TRUCK TYPES Three different types of trucks are available for use underground, namely the tip dumpers, telescoping dumpers, and push-plate dumpers. The following para¬graphs describe each of these three types. Tip Dumpers Tip dumpers are designed to lift the truck box, using gravity to dump the load out the rear of the box. The primary application of these trucks is in the haulage of muck to the surface. However, these trucks also may be utilized underground, if a chamber is provided to accommodate the raised truck box at the dumping point. Fig. 1 illustrates a four-wheel drive truck with a 10.0-t (11-st) capacity; this truck is only 1.9 m (6.25 ft) wide and is designed specifically to follow narrow and winding vein courses. Fig. 2 illustrates a two-wheel drive tip dumper with a 24.5-t (27-st) capacity; this truck operates on 12% grades with firm dry surfaces and in modes both loaded-up and loaded¬down. Telescoping Dumpers Telescoping dumpers specifically address the constraints imposed by low back heights, and they represent an optimization of compressed envelope size with maximum payload capacity. Figs. 3 and 4 illus¬trate a typical telescoping dumper with a capacity of 18.1 t (20 st). Fig. 3 shows the box in position for carrying the load, and Fig. 4 shows the same truck with the box in the full-dumping position. Fig. 5 illustrates the loading and dumping cycles. Fig. 6 illustrates an approximation of how an LHD unit with an eject-o-dump (EOD) bucket would be used to load over the rear of this type of truck. Fig. 6 shows a low-profile telescoping truck in the first stage of loading, with a 6.8-t (7.5-st) LHD unit equipped with an EOD bucket. A loader with a smaller capacity and a narrower bucket would allow the bucket to fit inside the truck box and would achieve an even lower loading height than that illustrated. Gen erally, an LHD unit equipped with an EOD bucket and teamed with a telescoping dump truck can be used with a lower back height than could any other front-end loader and truck team. Push-Plate Dumpers Push-plate dumpers are similar to telescoping Bump¬ers, except that they do not have the two-stage box. Instead, push-plate dumpers utilize a single push plate to discharge the load out the rear of the box. Gen erally, these units are limited to payload capacities of about 9 t (10 st). Fig. 7 illustrates a typical push-plate dumper.

Jan 1, 1982

By Michael Davis

In the fairly recent past, with a history of cheap and abundant energy, it has been possible to predict with reasonable confidence that world energy demand would continue to double about every 15 years. Those who attempted to forecast the role of nuclear energy in future electricity generation could also start with the fairly safe assumption that electricity demand would increase even faster : with a doubling in demand about every 10 years. To estimate the likely future world demand for uranium it was then necessary to introduce a number of other assumptions including the rate of penetration of nuclear energy, the timing and the specific fuel requirements. This series of assumptions naturally compounded the uncertainty, but, remarkably, usually led to future uranium demands being overestimated. Such a bias which has almost always been observed in predictions made over the past 20 years has increasingly made uranium producers sceptical when expected to match the forecast demand with increased production capacity and supporting reserves. This scepticism has, of course, been reinforced by the persistence so far of a buyers' market in uranium throughout the entire period of emergence of commercial nuclear electricity generation.

Jan 1, 1974

By Richard H. T. Garnett

In 1900, placer gold was discovered on the beach of Nome, AK on the southern coastline of Alaska's Seward Peninsula (Garnett, 1991). The site is about 800 km (500 miles) from Anchorage. Nome is connected to Anchorage only by air (daily) and by sea (summer). Total onshore placer gold production from Nome's immediate vicinity was more than 155.5 t (5 million oz). Alaska Gold Co, has continued to produce gold onshore with, until recently, two bucketladder dredges, each of 255-L (9-cu ft) bucket capacity. Small-scale marine dredging for gold has been at- tempted several times this century (Garnett, 1991). Western Gold Exploration and Mining Co. Ltd. Partnership (WestGold) is the only company to have been successful in achieving a significant offshore production. The Nome bucketladder-dredging operation from 1986 to 1990 constituted a unique marine-mining experience in the United States. \Inspiration Gold Inc., WestGold's predecessor, acquired six offshore leases in 1985. The total lease area of 87 km2 (21,551 acres) extended from the coastline to the 4.8-km (3-mile) offshore limit (Fig. 1). Those leases al- ready had been partially explored. Drilling was conducted off the shorefast winter sea ice. Therefore, it was rarely more than 1.6 km (1 mile) from the shore or in water deeper than about 9 m (30 ft). In 1985, estimated reserves comprised of a 5-m (17-ft) vertical thickness of sediments below 6.3 m (20 ft) of water. This meant a mean digging depth below the mean sea level (msl) of 11.3 m (37 ft). It was thought that the offshore Nome deposit possessed a feature that is common with many terrestrial gold placers - the secret of profitable exploitation of the marine deposit lay in maximizing the dredge throughput to minimize the unit costs. The inability of the project to withstand the prohibitively high cost of a new dredge was recognized. So Inspiration Gold purchased a used unit. This was the world's largest ocean- going bucketladder dredge (Fig. 2). Binzn was an 850-L (30 cu ft) bucket capacity dredge that was lying idle in Singapore. Originally constructed in the Jurong shipyard of Singapore in 1979, Bima was designed by Mining and Transport Engineering, a subsidiary of IHC Holland. Billiton Marine used the dredge for tin production at Pulau Tujuh in Indonesia (Dieperink, 1978) before it was laid up in mid-1985. Bima underwent a nine-week refit before departing Singapore on June 4,1986, with 800-t (880-st ) of deck cargo. It was dry-towed for 32 days to Alaska. A slower, less expensive, wet-tow at the authorized 5.5 kmthr (3 knots/hour) would have delayed the dredge's arrival in Alaska untl almost the onset of winter. The 13,000-km (8,100-mile) voyage was made on the deck of Smit Lloyd's "Giant-4" submersible barge towed by its 7.8- MW (10,500-hp) tugboat. The first season's dredging revealed several major shortcomings in Bima. Further repairs and modifications were undertaken at Tacoma, WA. The dredge returned to Nome for the June start of the 1987 summer dredging season. The refitted Bima worked offshore at Nome from 1987 to 1990. It produced 3.67 t (118,078 oz) of gold at an average recovered grade of 824 mg/m3 (0.0204 oz/cu yd). In 1991, the dredge was dismantled and sold.

Jan 1, 1997

By F. G. Miller

It is generally accepted that sulfur exists in coal in three forms: (1) pyritic, (2) organic, and (3) sulfate sulfur. Sulfate sulfur usually makes up less than 1% of the total sulfur content. Pyritic and organic sulfur, make up almost all of the total sulfur and occur in varying amounts in different coals and can vary greatly in coal of the same seam Pyritic sulfurs of 20% to 80% of the total sulfur have been reported Other authors have shown that it is not possible to remove the organic sulfur without chemically altering the coal. Chapman and Jones (1) state: "Organic sulfur, unlike pyritic sulfur does not exist as discrete particles, but is intimately associated with the coal structure, and as such it is not possible to remove it or reduce its concentration by physical means." Any success in removing sulfur has come about by removing pyritic sulfur by physical means; therefore, removal of sulfur in the pyritic form is the subject of this investigation. The extent to which any impurities can be removed from a particular coal can be determined by a washability study. Outside of crushing coal, to finer sizes or chemically altering the coal, there are no known methods of changing this inherent washability characteristic. The efficiency of various methods used to remove impurities can be determined by comparison of results produced at a yield to the results as shown by a washability study. In recent years heavy media processes have proven their ability to wash plus 28 mesh coal and nearly produce results shown to be theoretically possible by the washability study. Therefore, it is the objective of this paper to show various methods of treating the finer fractions of the coal, in the hope of developing a process, which can effectively produce in the fine fractions the efficiency of heavy media devices in the coarse.

Jan 1, 1963

By John H. Paugh

Hydraulic slurrying and pumpability characteristics of phosphate matrix (ore) have not been quantitatively defined. An elemental triangular diagram analysis of rock/sediment texture is used to classify the nature of the ore; then related to empirical field data of hydraulic pressureand production yardage ratios. This experiment is applied as a geotechnical tool to provide empirical data of ore slurry and pumpability characteristics as key considerations in the design of slurry pipeline systems. A real texture variability maps are developed on a section of land to assist mine engineering planning.

Jan 1, 1981

By J. Hanna

The University of Alabama Mineral Resources Institute (MRI) has developed a unique process for selective fatty acid flotation of carbon-ate gangue from sedimentary apatites "francolite" in the pH range of 4-6 without collector conditioning of the pulp. The process, which does not require an apatite depressant, was modified to beneficiate a high Mgo siliceous phosphate matrix from south Florida. The modified process includes two flotation stages, one for carbonate removal, as mentioned above, and the other for phosphate recovery from the siliceous gangue. The selective flotation separation of the carbonate and phosphate, from siliceous constituents of the matrix at various pH levels and collector dosages are discussed. In the carbonate flotation stage, about 70% of the Mgo was rejected in the froth and the phosphate flotation stage produced concentrates analyzing about 31% P2O5,0.7% HgO and 4% insol. The overall P2O5 recovery in the two stages is about 85%.

Jan 1, 1989

By S. J. Schatzel, J. D. Addis, V. Gangrade, L. L. Chasko, C. A. Hollerich

A ventilation study was conducted at a western U.S. coal mine to evaluate the movement of longwall face air and exchanges between the face and worked-out areas to document the presence or absence of face airflow pathways between these locations. This field study was part of a project investigating the effect of longwall face length and caving characteristics on longwall face air behavior and its potential movement on and off of the face. Tracer gas experiments using sulfur hexafluoride (SF6) were done to describe air movement on the face and in the mined-portion of the active panel. Maintaining adequate ventilation air on longwall faces is important for worker safety and for the dilution of methane emitted from the face and caved gob.

By E. A. Wieselmann

In 1970 Texasgulf (Australia) introduced natural gamma radiation logging of drill holes for exploration in the Hamersley Iron Province of Western Australia. Drill hole logs have allowed positive stratigraphic and structural correlations within complexly folded secondary hematite ore deposits and between individual iron ore deposits separated by distances in excess of seventy-five miles. A Neltronics model KPD logging system and gamma-ray sonde are being used to measure the natural gamma radiation of the enriched Brockman and Marra Mamba banded iron formations. The parent banded iron formations are composed of thick, chemically precipitated iron oxide, chert, iron silicate, and carbonate with thin intro-formational clastic horizons. These clastic horizons give a greater natural gamma radiation than the banded iron horizon, and each clastic horizon has a characteristic radiation profile related to its composition and thickness. Because the natural gamma-radiation profile is unchanged during secondary enrichment of the iron formation, the present stratigraphic position of each drill hole can be established and complex folding can be accurately traced in the sub-surface. Gamma ray logging of percussion drill holes has made feasible a significant reduction in diamond core drilling without loss of accuracy. At the same time, it has provided a means of rapid evaluation of complexly folded iron ore deposits.

Jan 1, 1975

By H. Habenicht

Requirements for full extraction in underground coal mining call for inexpensive, safe, techniques to be competitive with conventional methods. Longwall and shortwall systems are to some extent employed for this purpose. Another method would be rib pillar extraction (and pillar extraction). These methods are compared with each other with respect to procedure, equipment, safety, roof control, investment, output, performance, costs The advantages of r.p.e. show this method very attractive. Number and cost of equipment are lowest. Safety and roof control becomes improved by a mobile roof support recently developed in Austria. Its successful use in the R.S.A. is being explained.

Jan 1, 1986

By W. R. Reed

This study evaluates the roof-bolter canopy air curtain (CAC) system in an exhausting face ventilation system, demonstrating its effectiveness and illustrating the CAC protection zones. Two scenarios are considered: (1) a roof-bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof-bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment that contains 6.0 mg/m3 of respirable dust and is ventilated by an exhaust curtain with 9,000 cfm (4.25 m3/s) of air to simulate the roof-bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts and in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3/s) with dust reductions ranging from 39.5 to 82.8 percent. When the roof bolter is operated close to the face, increasing CAC airflow was required for adequate protection, as the dust reductions can be as low as 39.5 percent. Increasing CAC airflows to 350 cfm (0.17 m3/s) and 450 cfm (0.21 m3/s) were evaluated, demonstrating that dust reductions increased to 59.7 percent (350 cfm) and 72.0 percent (450 cfm). These results revealed improvement in respirable dust reductions compared to the CAC airflows at 250 cfm when the bolter is operated close to the face, showing the CAC can provide protection against high respirable dust concentrations for roof-bolter operators.

By M. J. Hart

There are no formulas that guarantee success when it comes to obtaining zoning approval for mineral aggregate mining. Local land use decisions often times represent the most controversial issues faced by community. Public awareness, concern, willingness to get involved, sensitivity to the environment and probably most importantly fear of change only begin to describe the atmosphere in which local land use decisions are made. Add to this the public hearing process which is quasi judicial, adversarial, and unfortunately not designed for resolution of disputes and it is not difficult to see the need for an alternative to present methods. Hopefully, some day we will have a process that will do away with or at least minimize unnecessary, unproductive and unmanageable community conflicts.

Jan 1, 1984