Search Documents

By W. Miola

The MSHA prescribed method for the determination of quartz in airborne respirable dust samples from underground coal mines is the P-7 method, a combination of low temperature radio-frequency ashing (LTA) and infrared analysis (lR). There is no prescribed procedure for quartz analysis in bulk samples of coal and host rock. Dispersive Infrared (IR), Fourier-transform Infrared (FTIR), and X-Ray Diffraction (XRD) methods are most commonly used for quartz analysis in powders. Several aspects of the experimental procedures such as the analysis sample preparation from bulk samples, ashing techniques, scanning procedures, peak measurement location, calibration techniques, sample amounts, size consist, and data interpretation affect differently the results from each of the methods. Significant differences in analysis results from X-ray diffraction (XRD) and infrared spectroscopy (IR) on the same samples are reported. All these studies point to the need for reliable quartz analysis methods. In a recent research, a procedure for preparing bulk coal and host rock samples for quantitative quartz analysis was developed. Further the results from X-ray diffractometry and infrared spectroscopy for quartz content on identical samples were compared. Calibrations with pure and mixed standards were used to assess the influence of particle size distribution, matrix, and calibration on analysis results. In this paper, several issues with the measurement of quartz in the samples of coal, host rock, and airborne respirable dust from mines are outlined and quantified.

Jan 1, 1994

By H. Sevim

Placement of coal combustion byproducts into abandoned sections of underground coal mines for the purpose of subsidence mitigation has been investigated in Illinois. Several handling and transportation systems have been examined. Prototype pneumatic and hydraulic placement systems have been developed and demonstrated. The demonstration site, Peabody No. 10 mine in Pawnee Illinois, is selected as a case study. It is found that, for a project of 5 years, transporting 150,000 tons of byproduct annually from a power plant located 32 km (20 miles) to the mine would cost $1.80 per ton and placement into underground would cost $3.07 per ton.

Jan 1, 1998

By J. J. Carlson

An important factor in filtration is the zeta potential of the particles. Since zeta potential is a function of pH, it was hypothesized that adding CO would lower the pH and zeta potential. A reduction in zeta potential should enhance the flocculation and increase the filtration rate. This paper describes the effects CO on the zeta potential of both pure hematite and samples of hematite concentrate from an iron ore processing plant. A significant shift in the zeta potential, as a function of pH, curve was observed. These results point to an alteration of the particles mineralogy, not just a shift in pH.

Jan 1, 2010

By A. A. Campoli

A stress control design strategy was developed to minimize the explosive failure of highly stressed pillars, during room-and-pillar retreat mining conducted between stiff immediate roof-and-floor strata. A confined core coal pillar strength model was based on in-mine geotechnical evaluations of successful room-and-pillar and longwall bump control designs. Tributary area and linear shear angle approaches were used to estimate development and gob side abutment pillar loads for supercritical section widths. Subcritical width sections separated by barrier pillars to control stress within total extraction panels were optimized with the boundary element program MULSIM/NL.

Jan 1, 1994

By R. R. Klimpel

This paper demonstrates, using the results of an unusually complete industrial test sequence, what the various interactions are between grind size, collector dosage, and frother type. While particle size is universally acknowledged to be important in optimizing industrial copper sulfide rougher flotation circuits, many of the various interactions that do occur at the industrial level with particle size are still being identified and/or quantified. This study also presents, in a consistent manner, the changes in flotation kinetics that occur as a function of particle size, in a typical industrial circuit along with some insights as to how flotation operators can optimize rougher circuit performance.

Jan 1, 1993

By J. J. Sammarco

Computer-aided control of a mining machine pl aces its operator in a safe, remote location, thus reducing health and safety risks, Sensing systems that provide machine position (xy coordinate) and heading (yaw), are extremely useful in aiding remote positioning of mining machines. The U. S. Bureau of Mines has developed two sensing systems for position and heading information: A scanning laser system based on the Lasernet sensor and a mechanical position and heading system based on linear-position transducers. The Bureau is also investigating a system from Honeywell, the modular azimuth and positioning system that employs ring-laser gyroscopes. This paper presents a brief background and status of these sensing systems as applied to the remote positioning tasks of a continuous mining machine. Included are field test results of each system operating in a room-and-pillar research section at a cooperating mine in West Virginia.

Jan 1, 1992

By J. F. T. Agapito

Significant economic benefits can result when rock mechanics is applied within a practical framework and integrated within the other engineering functions of the mine organization. This requires management support and understanding of rock mechanics as a practical tool to help attain high standards of safety, productivity and resource recovery. For such an approach, a long-term geotechnical program is needed in most operations to build an adequate data base and to ensure that design and ground control issues are handled in a cost-effective manner. This paper presents a summary of four case studies where significant economic benefits were realized with the help of rock mechanics. Although cost savings were not computed, the economic benefits are obvious and clearly impacted the mine operations favorably.

Jan 1, 1990

By R. W. Wittkopp

The Relief Canyon gold deposit is located approximately twenty- four kilometers east of the town of Lovelock in Northwestern Nevada. At Relief Canyon, the Late Triassic Grass Valley Formation has been thrust over the Late Triassic Natchez Pass Formation. The lower plate Natchez Pass Formation is composed of massive gray dolomitic limestone which is locally silty and sandy. The upper plate Grass Valley Formation is composed of shale, siltstone, argillite and quartzite. Gold mineralization at Relief Canyon occurs along the highly brecciated thrust contact between these two formations. Weak gold mineralization often occurs above the thrust in the Grass Valley Formation, however, most of the ore grade mineralization is present below the thrust in the brecciated Natchez Pass Formation or where the two formations are mixed as a result of movement along the thrust. Several types of gold mineralization have been recognized at Relief Canyon. A large amount of the ore is present as a jasperoid breccia, however, significant amounts of ore occur as a mixed breccia composed of upper plate rock, fresh limestone, clay and jasperoid breccia. Gold ore also occurs in a fresh limestone breccia which contains a large amount of clay. Below masses of jasperoid, jasperoid stringers containing gold extend into the fresh limestone. Gold mineralization at Relief Canyon appears to be truly disseminated and has the typically associated trace elements of arsenic, antimony, mercury and fluorine. The Relief Canyon deposit can be classified as a structurally controlled disseminated gold deposit. Other deposits that fit this classification are the Pinson and Dee gold mines.

Jan 1, 1984

By Mads Aniksdal

New Nedre Fiskumfoss is a construction project in North Trøndelag, Namsen River. The purpose of the contract is construction of a new hydropower plant, that will phase out the existing power plant in the same waterfall. The contract consists of a tunnel system with cross sections from 16 m2 to 150 m2, powerhouse and transformer in rock caverns, 6 shafts and major works with inlet and outlet below river level. Technical challenges consist of demanding design on rock extraction, cofferdams, solid constructions with challenging design and demanding rebar work, as well as restrictions and unpredictable water flow in a national salmon river.

Jun 13, 2023

By R. L. Grayson

Productivity achievements in underground coal mining over the past ten years highlight the improvement of management practices as well as the adoption of new technology. Research findings and results from operational studies characterize the aspects of good management that translate into high productivity. In concert with these findings, the Mine Management Support System (MMSS) is being developed, under co-sponsorship of the U.S. Bureau of Mines and the West Virginia University Energy and Water Research Center, as a knowledge-based system to enhance more efficient management of underground coal mines. Concentrating on capturing the intricate knowledge needed to manage a mine effectively, MMSS will encompass information and rules on work scheduling, desired work practices, regulations impinging on operations and planning, responses to operating problems, and the labor-management work agreement.

Jan 1, 1990

By J. Villeneuve

Steady-state simulation has proved to be a very useful aid in designing new plants and optimizing existing ones. The algorithms and data definitions of existing simulators often, however, require a great deal of expertise for implementing a simulation-based methodology. The constraints imposed by conventional simulators are explained and the advantages of a new algorithm, the Objective-Driven Simulation, are shown. These advantages are a) an improvement in the simulation results, which enables simplifications of the methodologies used, and b) the possibility of taking into account economic objectives for plant operation, thus extending the range of application of steady-state simulation.

Jan 1, 1992

The future phosphate rock deposits in South Florida contain a significant fraction of dolomite. The high MgO content of the rock is undesirable in the production of phosphoric acid. Several flotation schemes have been attempted to separate dolomite from phosphate rock. Alternately, Selective Flocculation process has been suggested to separate dolomite from apatite. A high MgO content rock was simulated by a 30:10:60 synthetic mixture of apatite, dolomite and silica. Single mineral selectivity was observed in the mixed mineral systems apatite-silica and dolomite-silica with Polyacrylic acid (PM) and Poly(ethylene oxide) (PEO) flocculants respectively but not realized in apatite-dolomite system with PEO flocculant. Heteroflocculation, suspected to be the major reason for loss in selectivity, was minimized by addition of a Site Blocking Agent (lower molecular weight fraction of PEO). Process parameters such as size reduction schemes, flocculant/SBA dosage, and pH were investigated to achieve the desired separation. The selectivity obtained in binary mixed mineral tests was translated into the ternary mixed mineral system, viz. apatite-dolomite-silica. In this presentation surface chemical characterization of the samples and their flocculation behavior will be discussed.

Jan 1, 1994

By Joshua Cole, Joshua Sovechles, Christian Cardoso, Guillermo Bermudez, Martta Hirsi, Joshua Dettamanti, Rabia Abbasi

The implementation of technological advancements in flotation is key to optimize performance in mining operations. Consequently, flotation cell’s performance is highly dependent on the effectiveness of the mixing mechanism. A more efficient flotation mixing mechanism is likely to improve metallurgical performance and optimize energy consumption, which is the motivation for Metso’s journey to develop the latest iteration of FloatForce®. Looking to test the new design at plant scale, Metso approached the Kennecott Copperton concentrator, which is continuously looking for different venues to improve metallurgical performance. In this context, a test campaign was conducted to implement this new flotation mixing mechanism in their rougher circuit during 2024. The industrial trial consisted of several sampling campaigns assessing different operational parameters for comparison purposes around a 300m3 flotation cell. The effect of the new flotation mixing mechanism on the cell’s power draw was also studied. The results of this trial at Kennecott are presented in this paper. Overall new flotation mixing mechanism, FloatForce+ was seen to perform as well as the original FloatForce.

Feb 1, 2025

By A. S. Atkins

The interest in the use of micro- organisms in the leaching of sulphide minerals has been traditionally exploited as a scavenger process for the recovery of valuable metal by- products from waste ore dumps. Environmental concern on sulphur emission from conventional pyrometallurgical plants together with the cost of stack cleaning systems to comply with legislative control also indicate baccerial leaching to offer a low cost treatment for the processing of sulphide minerals. The paper describes the effect and limits of relatively coarse particles on the complete leaching of pyrite and its importance to the practical application in dump leaching operations of sulphide minerals. It has also been demonstrated that static leaching techniques have encouraging economic potential for process plant operations compared with agitated leaching systems.

Jan 1, 1984

By R. Mensah-Biney

The loading characteristics of gold-tetrabromide species onto activated carbon have been evaluated using a completely mixed batch reactor system. The overall loading of gold onto carbon was rapid for the first hour but continued slowly without cessation as a result of reduction of gold. Conventional equilibrium considerations were therefore not applicable. Although loading continued slowly after several days, abnormally high loading capacity values of 10-12 meq/g carbon (650-800 kgAu/tonne) could be attained within 72 hours. The loading of gold-bromo species by activated carbon was by the mass transfer of [AuBr4l-onto the carbon surface where reduction to metallic gold took place. Elution of gold from the loaded carbon was feasible provided the carbon had not been loaded to too high capacity values. If loading is carried to high levels, complete elution becomes impractical and the gold may be recovered by ashing the carbon. For the high loading capacities observed, this option would appear to be cost effective. The effect of several variables on the loading capacity of the activated carbon is discussed.

Jan 1, 1992

By R. G. Johnston

Minerals have many uses in paint systems. These roles include use as primary and extender pigments, sheen control, film durability enhancement, and rheology control. These and other uses of minerals in paints, and the effects of mineral quality variations on coatings performance are discussed. As coatings performance requirements become more demanding, tighter consistency of important mineral properties, such as particle size distribution and purity, is becoming increasingly vital. Future directions of mineral use to meet projected environmental restrictions and performance demands on coatings, including the use of advanced minerals technologies, are examined.

Jan 1, 1993

By Albert F. Duzy

Recently there have been some problems associated with hot coal in shipments from the USA to overseas markets. This paper will serve several functions. First, a brief review is presented, together with a selective bibliography. Second, a thorough discussion of coal oxidation is covered. Third, potential effects of storage are presented and, lastly, methods are suggested for the safe storage and bulk transfer of coal. The scope includes coal storage for power plants.

Jan 1, 1983

By R. R. Rollins

Field data combined with theoretical derivations were used to design a surface mining operation using explosive casting. Calculated casting results varied from 44 to 65% depending on bench height. This model was then applied to field tests at an eastern, contour, coal stripping operation. Results from five experimental casting shots are summarized and compared to conventional mining methods. The overburden material removed by casting ranged from 35 to 65% with an average of 50%. Fragmentation was improved and it was demonstrated that this procedure is economically attractive with a resultant cost savings of $.59/m3 or $5.93/t of clean coal.

Jan 1, 1987

By J. R. Henke

Dewatering wells producing iron-rich water experience rapid declines in yield and drawdown due to the formation of ferric (Fe +) hydroxide deposits in well screen, pump intake and riser pipe. Precipitation is caused by a combination of dewatering-promoted iron oxidation and iron-oxidizing bacteria. Physical and chemical well rehabilitation techniques, as well as alternative well construction and well development techniques designed to minimize well clogging, were evaluated in this study. The addition of acid downhole feed systems to dewatering wells prone to iron encrustation can, in some cases, prolong their operational lives up to 500 percent that of unacidified wells.

Jan 1, 1989

By D. C. Martin

Construction of the Cerro Colorado on-off leach pad in northern Chile required placement of approximately 3,000,000m3 of fill over a P1an area of approximately 600,000m in irregular terrain with relief of up to 40m. Earthwork construction was completed in approximately six months using mine waste which was placed in 4 to 6m lifts using mine haul trucks. The lift thickness was reduced and the compactive effort increased in the upper 10m to enable development of a mat and additional resistance to possible differential settlements under dynamic (earthquake) conditions. A single 80 mil (2mm) HOPE liner was used below the leach pads and this was protected from the loading and unloading equipment using an engineered liner system consisting of screened sand, gravel and silt from local sources as the bedding and cover layers, and a heel of screened gravel and primary crushed low grade ore. Settlement monitoring, field testing and subsequent assessments of liner performance have indicated an adequate design was achieved and the project proceeded with considerable savings in time and construction costs.

Jan 1, 1995