Search Documents

By Prakash Venkatesan, Mehmet Ali Recai Ӧnal, Shaik Saida, Veerendra Singh, Chenna Rao Borra, Manish Kumar Kar

A laboratory-scale investigation of the effect of milling operation and catalyst addition ( K2CO3) on the partial reduction of low-grade pyrolusite ore pellets was carried out using coke as a reductant. Thermogravimetric analysis was used to understand the correlation between milling and catalyst addition parameters with the reduction temperatures. DTG analysis of pyrolusite pellet reduction showed three distinctive peaks associated with a three-step reduction mechanism (i.e., MnO2→ Mn2O3→Mn3O4→MnO). The results showed that the grinding and addition of the catalyst have a significant effect on lowering the MnO2 reduction temperature independently. But maximum reduction temperature drop is obtained when combining grinding and catalyst addition in this work. By 3 h milling and 10 wt% catalyst addition, the reduction temperatures were reduced by more than 200 °C compared to the raw ore pellets. These results obtained from the DTG analysis were further supported by XRD analysis of the reduced samples.

Dec 20, 2022

By E. H. Smith

St. Joe Minerals Corp., a subsidiary of Fluor Corp., treats high-grade gold, silver, and copper ore at its El Indio plant at an altitude of 4 km in the Chilean Andes. The ore is complex, being a mixture of massive pyrite-enargite and quartz, both containing very fine gold and silver. Treatment produces a copper flotation concentrate containing high levels of gold, silver, and arsenic, and also dore bullion. Part of the flotation concentrate is roasted to remove the arsenic content, and arsenic trioxide is collected as a by-product.

Jan 1, 1987

By QUANWEN PU, Yonggang Wei, Bo Li

With the advancement of industrial science and technology, more and more catalysts are used. The spent catalysts produced are solid waste products, which cause environmental pollution if they are not treated. At the same time, the spent catalysts contain some precious metals such as platinum in concentrations that are often higher than in their ore resources. Therefore, the recovery of valuable metals in spent catalysts is a hot research topic at present. However, due to the complex structure of the spent catalysts, dealing with them is a lengthy process. The first step of recovery, enrichment of the spent catalyst, becomes particularly important. In this paper, a pressure solution method is investigated for this purpose, in which the alumina carrier is dissolved and platinum is enriched in the leaching residue.

By Jerry W. Owens

Current steel consumption for grinding media, mill liners and rods in North America runs in excess of 400,000 tpy in the mineral processing industries. Steel consumption ranks as one of the major consumables along with energy in most operations with total annual industry expenditures in excess of $275 million. It is generally agreed that there are 3 main categories of wear responsible for this metal loss. These three main types can be loosely defined as follows; 1) Abrasion. The cutting, rubbing, scrapping and gouging of the metal surface by the ore with which it is in contact; 2) Impact. Spalling on both micro and macro scale, breakage, and deformation due to metal to metal contact; 3) Corrosion. The oxidation losses of the metal due to electrochemical interaction between the grinding media and the slurry

Jan 1, 1984

By L. L. M. Kadnuck

The U. S. Bureau of Mines studied the suitability of using flexible tendon cable supports as secondary roof supports at a western coal mine. The supports were installed in longwall tailgate entries and grouted into the mine roof. This paper quantifies how the use of cable supports can improve ventilation in underground airways. A mine ventilation simulator was used to model the changes in airway resistance and airflow and show potential for further ventilation improvements when cable supports are used. Model results indicated that cable support use translated to savings in air pressure around the longwall panel and increased airflow at the longwall face.

Jan 1, 1994

By Harry M. Conger

Thirty years ago, the U.S. gold mining industry was hanging on by its fingernails. Save for one great mine, the Homestake, most production was coming from copper smelters such as Kennecott and Magma. Even Homestake itself was under great pressure from rising costs and a fixed price for gold. The outlook was dim, to say the least. Today, as it has for most of the past decade, the American gold mining industry stands among the world leaders in production, and in the development of mining and mineral processing technology. What caused this dramatic change? Obviously, the freeing of the gold price was a major factor, as was the decline in South African production, but these events alone could not have created the U.S. strength we see today. It was technology, investment, and the determination of miners to build an entirely new industry that were the indispensable ingredients. The U.S. Bureau of Mines, with great foresight, had begun the research that led to heap leaching before the gold price began to rise, and Newmont had committed to build a small mill at Carlin, a move then considered quite risky. From that point, the U.S. gold mining industry was placed on lower-grade ores then being found in Nevada and elsewhere, but it was soon apparent that we would have to develop new technologies to deal with more refractory ores, carbonaceous as well as sulfide-bearing. This is now being done with considerable success. Despite its success, or perhaps because of it, the gold mining industry has come under pressure from various groups who characterize their activities as motivated by "public interest." The public interest they refer to properly include the health and safety workers and impacted communities, as well as protection of the environment, and with these concerns we miners have relatively little argument. In fact, we consider health, safety and the environment among our highest priorities, and not just because regulations may require us to do so. The argument, however, is not about the regulation of a viable mining industry, it is about a well-organized movement to attack and condemn mining in the media and to misrepresent its importance to the Nation and its willingness to accept responsible regulation. Once largely local or regional, the interest groups to which I refer are now quite large, national in scope, and even becoming international. This trend, taken together with finances raised from their dues and contributions, would make the interest groups formidable adversaries for mining, but their grip on the media enormously magnifies their influence. Unfortunately, it also makes possible the wide dissemination of incomplete, incorrect or slanted information. I am not here to "bash" the interest groups. On the whole, I believe that many of them have made positive contributions to society. As conservationists, however, I question their authority to make, or foster, decisions about which American industries and communities live and which die. To illustrate, I would like to present for your consideration the problem of cyanide, one of the issues over which the gold mining industry is most threatened. CYANIDE-POISON OR MIRACLE SOLVENT? Let me get this out of the way right up front: cyanide in most of its chemical forms is toxic. In some forms it is also listed as a carcinogen. These are adverse characteristics cyanide shares with a considerable number of industrial chemicals, including some that are widely used without the stringent regulations already in place for the mining uses of cyanide. In these uses, by the way, the risk to humans comes from direct ingestion of cyanide or cyanide-bearing solutions, or from the accidental acidification of solutions leading to release of hydrocyanic acid gas. That these risks are under control in mining can be seen from the fact that, in modern U.S. practice, there has never been a documented fatality attributed to cyanide! Because of its toxicity, cyanide cannot enter and be accumulated in the food chain. It can, however, be a threat to birds and animals that ingest cyanide-bearing solutions. Protection against this is, quite properly, a responsibility of individual mining operations, and considerable sums are spent each year to prevent or reduce bird and animal exposures. It should be evident, though, that many human activities, including highway traffic, windmills, use of pesticides and the like, result in bird and animal losses. Mining's use of cyanide, and the measures taken to protect birds and animals, should be considered in context. Cyanide must be kept out of surface streams and groundwater, and existing regulations mandate this. Any cyanide residues left in leach heaps, waste dumps and disused facilities must be eliminated, and we have proven technologies to do this now, just as we have means to detoxify tailings prior to disposal. The gold mining industry decries those rare instances when irresponsible operators fail to deal with contamination, and agrees that they should be held responsible. We do not agree, however, that the great majority of responsible companies should be punished, in advance, for accidents that have never happened. So much for the poison, what about the "miracle solvent?" Is that an overstatement? Well, consider the fact that gold has been called "noble" from earliest times, because it does not oxidize under atmospheric exposure, and that it appeared to the ancients to be utterly insoluble. Later generations of scientists did discover that it could be dissolved, but only by a combination of acids so potent that it became known as aqua Regia. Later still, it was found that chlorine would also dissolve gold, and attempts were made to base commercial processes on this, without a great deal of success. It remained

Jan 1, 1995

By Dan Nilsson

Open pit mining is the strong sector of the American mining industry. In the middle of the 60's. 17-18% of the ore in metal mines was mined with underground methods. From the middle of the 60's to 1980 the production in open pit metallic mines increased from about 400 to close to 600 million short tons while at the same time the underground mine production decreased a little, from about 90 to about 80 million tons. Less than 15% of the ore prodction now come from underground mines. Large amounts of waste rock were also handled in the open pits. In the middle of the 60's about 600 milion tons were handled, in 1980 1,200 million tons were moved. This means that the average stripping ratio increased from about 1.5 to over 2.0 tons of waste rock per ton of ore, figure 1.

Jan 1, 1983

By Sam M. Pickering

Most high, purity silica is produced from crystalline quartz-generally from sand. However, there is a small area of southern Illinois where a porous, friable white chert rock is found which is very different in physical form from quartz sand. This microcrystalline material, commonly referred to as tripoli, is more easily ground to micron sizes than sand. Although of similar Moh's hardness, microcrystalline tripoli is less abrasive than either ground quartz sand or many synthetic abrasives. Location The southwestern corner of Illinois is underlain by extensive deposits of very porous chert; in some places the material is quite white. Two companies - Illinois Minerals Co. and Tammsco, Inc. - mine and process this white material. The Illinois Minerals plant is located at Elco, and the Tammsco plant is in Tamms, Illinois. Both companies mine from various locations within a ten mile truck haul of their plants. Production from this district has been continuous since at least 1915. Malvern Minerals Company mines and processes a generally similar microcrystalline, friable novaculite near Hot Springs, Arkansas.

Jan 1, 1985

By Milos Krofta, Donald B. Aulenbach, James P. Van Dyke

INTRODUCTION An innovative Ø.1-MGD (378.5-m3/day) biological and phyicochemical wastewater treatment system at Hancock, Massachusetts, USA, has been treating the domestic sewage generated from the four-season Jiminy Peak timeshare resort since 1985. The influent raw sewage is collected and equalized in an equalization tank, then biologically treated by two rotating biological contactors (RBC). A portion of the RBC effluent is discharged to a secondary sedimentation tank to simulate conventional waste treatment by a conventional RBC system. For parallel treatment the remaining portion of the RBC effluent is discharged to an innovative Sandfloat (SASF-8) clarifier to simulate a two-stage biological and physicochemical treatment by RBC-Sandfloat. Both secondary sedimentation effluent and Saandfloat effluent are later combined together and discharged to a tertiary sand filter and two UV disinfection'units for final polishing. The operation and performance data of Jiminy Peak plant in the period of May 1985 to March 1988 was fully documented in the Lenox Institute technical report No. LIR/Ø3-88/292 (391 pages, March 1988). This report presents only background information and complete plant data in the period of April 1988 to January 1989. Dr. Lawrence K. Wang and Mr. James P. Van Dyke have been the Consulting Engineer and Director of Special Projects, respectively, for the Jiminy Peak Project since 1985. (Key Words) Innovative and Alternative Technology, Rotating Biological Contactor, Sandfloat, Dissolved Air Flotation, Sedimentation, Tertiary Filtration, Ultraviolet, Disinfection. BACKGROUND INFORMATION Jimmy Peak, Inc., Hancock, Massachusetts, has designed and constructed a secondary wastewater treatment system consisting of preliminary/primary treatment facilities, two rotating biological contactors, a dissolved air flotation clarifier, a secondary sedimentation clarifier, a sand filter and two ultraviolet (UV) disinfection units. Total average wastewater flow is approximately Ø.1 ) (378.5 cubic meters per day). In accordance with the Consulting Engineer's preliminary design, the total wastewater stream is initially collected and equalized by an equalization tank, and then biologically treated by rotating biological contactors (RBC). Part of the RBC effluent is diverted to a Krofta Sandfloat (SASF-8) for physicochemical clarification in order to simulate an innovative RBC-Sandfloat two-stage waste treatment system. The remaining part of the RBC effluent is diverted to a sedimentation tank for secondary clarification in order to siumulate a conventional secondary RBC-sedimentation waste treatment system for the purpose of parallel comparison. Both Sandfloat effluent and sedimentation effluent are later combined together and discharged to the subsequent sand filter and UV disinfection unit for final polishing. Figure 1 shows the flow diagram of Jiminy Peak Plant. The Massachusetts Clean Waters Act (M.G.L.c.2l,s.26-53) was amended by Chapter 246 of the Acts of 1973 to authorize the Massachusetts Department of Environmental Quality Engineering (DEQE), Division of water Pollution Control, Boston, Massachusetts, to regulate discharges into all waters of the Commonwealth of Massachusetts, including groundwaters. The DEQE regulates discharges through the issuance of discharge permits which impose limitations on the amount of pollutants which may be discharged in the effluent, together with monitoring and reporting requirements and other conditions to insure adequate treatment of all liquid wastes prior to discharge. The DEQE reviewed the application submitted on behalf of Jiminy Peak, Inc. for a permit to discharge sanitary wastes from the Jiminy Peak secondary wastewater treatment system located off Brodie Mountain Road, Hancock, Massachusetts, and subsequently developed the conditions contained in the Groundwater Discharge Permit No. Ø-188. More specifically, Jiminy Peak, Inc. (i.e. the permittee) has been authorized to discharge into the ground from the Jimmy Peak secondary wastewater treatment facilities for which the Permit No. Ø-188 was issued, a treated effluent

Jan 1, 1989

By J. L. Workman

The stability of spoil and highwall slopes are important to successful strip mining. This paper discusses soil parameters of importance in stability analysis. The common mechanisms of spoil failure are discussed. Modes of highwall failure are also outlined. The importance of water to stability is presented. Dragline mining methods most suited to creating spoil and highwall profiles that address stability needs are provided. It is concluded that groundwater and surface runoff must be well controlled, and that it will often be necessary to modify spoil and highwall configurations to achieve a stable overall slope angle.

Jan 1, 1996

By James R. Jones

The purpose of these opening remarks is to establish a viewpoint, which will form part of the basis for later discussion between panel members and between the panel and the audience. Important issues will be identified. These ideas in the form of questions and answers, hopefully, will provide the necessary background for the ensuing dialogue. Is There An Urgency? We do not believe there is the urgency for immediate control legislation that has been depicted by some Congressional sources, environmental groups, and certain segments of the press. Emissions of sulfur oxides in the United States have decreased 15% during the 19701s, even though the use of coal by electrical utility power plants increased nearly 80%. That trend will continue as the older plants are phased out of operation and are replaced with newer plants, which must meet the New Source Performance Standards (NSPS) requiring the use of "scrubbers" to reduce sulfur dioxide emissions by 70% or 90%. The present Clean Air Act Amendments of 1977, by allowing the logical progression of economic events- -depreciation, retirement, replacement, and growth--will produce approximately a 50 % reduction in SOX emissions by the year 2015.

Jan 1, 1984

By T. A. Lloyd

The use of tank cells over the years has provided a means for low cost, space efficient, extra capacity in existing flotation circuits. In some cases, new plants have selected tank cells as the machine of choice. Typical tank cells use high efficiency impellers for mixing, which results in low power draw. Unfortunately, these mixers have poor aerating characteristics that compromise metallurgical performance. This has all changed with Outokumpu's new flotation concepts. Outokumpu has recently developed the HG or High Grade flotation cell that can provide higher recovery with better selectivity while maintaining the simple operation of conventional cells.

Jan 1, 1993

By Lukas Erkurt, Wolfgang Holzer, Stefan Auderer, Richard Gradnik

SEM/ NATM Tunnelling contracts in Austria and Germany are usually tendered applying unit price contracts. The purpose of this paper is to show how contractual problems are resolved in these countries. The focus will be put on describing the theoretical approach, several case studies will show how contractual problems were dealt with on site.

Jun 23, 2024

By S. S. Peng

The generation and transportation of the airborne dust are mainly governed by the velocity and the movement pattern of the ventilation air in the longwall face. Generally speaking, the higher the air velocity, the more the airborne dust will be generated and the longer the period of the dust of certain size will be carried away from the source. In order to effectively prevent the production and the spread of the airborne dust, The airborne dust concentration distribution in the longwall face must be known in advance. Before the dust concentration distribution can he predicted theoretically with confidence, the air velocity distribution pattern of the ventilation air in the longwall face area must be determined first. However, the complicated, time-dependent and unpredictable mining conditions along and around the face area make the theoretical studies of the problem rather difficult. For instance, one of the factors commonly affecting the air velocity distribution at the longwall face is the air leakage, either into or from the gob area. The leakage quantity and the location of occurrence differ from mine to mine, face to face, and time to time. They depend not only on the compactness of the caved roof fragments in the gob, but also on the degree of obstructions in the working space and in the return entry. Another obstacle to the theoretical studies about the velocity distrbution is the complicated boundary conditions of the ventilated spnce which is very difficult to represent accurately in mathematical forms. In this paper, the air velocity distributions measured in four longwall faces are presented. A statistical model for each longwall face is also derived for prediction of air velocity distribution in the longwall face.

Jan 1, 1985

By İbrahim Gunes, ATILA GURHAN CELIK, Eren Komurlu

This study introduces a new apparatus designed to improve the load-bearing capacities and insertion efficiency of split set type friction bolts. Laboratory and site studies demonstrated the apparatus’s advantages in terms of practicality and prevention of buckling. The apparatus temporarily compresses the split tubes, reducing friction during insertion and increasing normal stresses and friction capacity at the bolt-rock contacts.

Jan 3, 2022

By J. H. Fowler

Canada's gypsum industry began over two hundred years ago in the Maritime Provinces when farmers attempted to supplement their incomes by selling "land plaster" to traders bound for the United States. Rising from such humble beginnings, gypsum now contributes significantly to the economies of nine of Canada's ten provinces. Thirteen open-pit and three underground mines produced a total of 8.38 million tonnes of crude gypsum and seventeen processing plants manufactured 2.49 million tonnes of finished products in 1985. Recent economic growth in North America has resulted in steady increases in gypsum production, however, competition from foreign producers and by-product gypsum poses a growing threat to Canada's gypsum mining industry.

Jan 1, 1987

By Alex Stewart

Most iron bearing ores treated by the R=N Direct Reduction Process yield products lower in phosphorus than the initial ores. The sulfur is also removed and generally is in the range of 0.02 to 0.05 percent in the final R=N product, independent of the sulfur content of both the ore and carbon fuel used. The mechanism and thermodynamic justification of the principal reactions leading to the removal of both phosphorus and sulfur and the control of sulfur in the iron concentrate produced are discussed and supported by the results of laboratory experiments. In substantially all iron ores (containing up to 4% sulfur as sulfate) and solid carbon fuels (containing sulfur from 1 to 8%) tested, the rejection of sulfur has been in the order of 90-95%, with not more than 0.02 0.05% sulfur in the final metallic iron product. With respect to phosphorus-bearing iron ores ranging up to 0.70% P205, the rejection to tailings has been in the order of 70-95%, resulting in not more than 0.03 - 0.07% phosphorus in the final product.

Jan 1, 1958

By Dan S. Nilsson

When an open pit mine is deepened, more and more waste rock must normally be removed. Techniques for optimization of open pit design are well-established within the mining industry. The recommended method is to choose the open pit alternative with the highest net present capital value of open pit and future underground mining. When the open pit is mined out, the operation must be closed, or, if it is profitable, mining must start underground. When planning an underground operation we experience the same type of optimization problem that occurs when determining the optimal depth for open pit mining. When mining underground the ore body is often divided into a number of areas, blocks or slices, each containing a transportation system with trains, trucks, conveyors, etc. When all the ore within such a part of the deposit is extracted, the operation must be closed, or, if it is profitable, a new transportation must be developed. The question that now arises is: how large a pan of a deposit shall be included in the first development and how much shall be left for future consideration?

Jan 1, 1981

By K. K. Kohli

Since the adoption of the Surface Mining Reclamation and Control Act of 1977, which mandates that surface subsidence be an intergral part of the underground coal mine design, there has been a sudden rise of demand on guidelines for minimizing surface subsidence and its associated structural damages. Unfortunately there is no sufficient amount of systematic subsidence data to fill such a gap, although considerable research has been devoted to the subsidence-induced damages of surface structures in the past. However, it was said that many surface subsidence surveys have been performed and monitored by coal companies during the past twenty years, and that it will be a great source of information for subsidence engineering design if they can be collected and assembled together. An effort was therefore initiated in the Department of Mining Engineering, West Virginia University, under contract with the U. S. Bureau of Mines in December 1978 to contact each individual coal company in the Northern Appalachian Coal Field for any surface subsidence survey data. After 10 months' survey, the data collected include 17 longwall panels and 2 room and pillar sections. The data in-each panel and section cover the complete set of subsidence survey raw data, underground mine layout maps, surface topo maps, geological loggings showing the stratigraphic sequences and thickness of the overburden, and if available, locations and types of surface structures. On-site visits were followed to study the surface terraines and structures. Interviews were conducted with the owners of the surface structures in most cases about, if any, the history and characteristics of damages.

Jan 1, 1980

By Elmer H. Citron

The Monterey Coal Company, a wholly owned subsidiary of The Carter Oil Company of Houston, Texas, recently awarded a contract to build the Monterey No. 1 Preparation Plant, which will be located near Carlinville, Illinois, to the McNally Pittsburg Manufacturing Corporation. The preparation plant will be one of the most modern jig preparation plants in the State of Illinois. Illinois No. 6 coal will be delivered by a 48" slope belt having 35-degree carrying idlers, operating at 650 FPM and operating on an incline of nearly 17 degrees. The slope belt is driven by two 450 BP motors and will deliver the mined coal at the rate of 1800 TPH to a stationary step-type ' screen having six-inch openings. The overproduct from the stationary screen will discharge into a 10' x 24' McNally Rotary Breaker and the underproduct will bypass the rotary breaker. The rotary breaker is equipped with heavy manganese screens with 6 ½" diameter openings. The sized 6" x 0 coal from the stationary step screen and the rotary breaker will be discharged by gravity to a 4%" raw coal incline storage belt. The 48" raw coal storage belt will deliver the 6" x 0 sized coal at the rate of 1800 T?H to an 8000 ton concrete raw coal silo, 70 feet in diameter and 1x7 feet high. The 6" x 0 sized coal will be drawn from the concrete storage silo by seven (7) 36" wide reciprocating plate feeders. Five feeders are to have constant speed drives at a rated capacity of 145 TPH each. Two (2) feeders will have remote con- trolled variable speed drives, to provide a varying feed.

Jan 1, 1970