Search Documents

Researchers from the National Institute for Occupational Safety and Health (NIOSH) are developing a coal pillar rib rating (CPRR) technique to measure the integrity of coal ribs. The CPRR characterizes the rib composition and evaluates its impact on the inherent stability of the coal ribs. The CPRR utilizes four parameters: rib homogeneity, bedding condition, face cleat orientation with respect to entry direction, and rib height. All these parameters are measurable in the field. A rib data collecting procedure and a simple sheet to calculate the CPRR were developed.

Jan 7, 2020

By N. Aouad

Dump truck operators are exposed to whole-body vibration (WBV) levels that exceed the International Standard Organization (ISO) 2631-1. The WBV level measured by RMS acceleration value, for operator comfort, and long-term health and safety is under 0.315 m/s2 by these standards. However, fundamental research by Frimpong and Aouad (2009, 2012) and field experimental study by Kumar (1999) have shown that operators are exposed to extreme WBV levels exposing them to injuries and musculoskeletal diseases in the long-term. These extreme WBV values in the vertical direction are equal to 3.56 m/s2, 1.12 m/s2 and 0.87 m/s2 for the operator?s seat, lower-back and cervical regions, respectively. This paper will outline current research to solve these problems. Keywords: WBV, Truck Vibrations, MSC.ADAMS, Virtual Prototyping

Feb 27, 2013

By Gregory T. Ziegler

A complex soil profile and high water table, together with a below-grade active subway tunnel, an above-ground elevated railway line, and the heavily travelled Northern Boulevard all passing above the tunnel alignment, combined to make mining of New York?s Northern Boulevard Crossing what is widely considered to be the most challenging portion of the multi-billion-dollar East Side Access project. The Northern Boulevard Crossing is a vital link in this project which, when completed, will connect the Long Island Railroad to Grand Central Terminal in Manhattan. How the sequential excavation method (SEM) tunneling was successfully accomplished, despite the obstacles, was a textbook exercise in practical innovation coupled with close cooperation between the owner, the construction manager, Hatch Mott MacDonald, the designer, Parsons Brinckerhoff, the contractor, Schiavone-Kiewit, and spe-cialty geotechnical contractor, Moretrench.

Sep 1, 2013

By H. Arima, T. Fujita, W. Yen

The copper catalyzed gold oxidation and reduction mechanisms in ammonium thiosulfate solution were investigated by Eh-pH diagram based on the optimum reagent combination for 60 mass% -75 µm silicate ore at 16g/t Au with the maximum gold extraction of 92% and the minimum ammonium thiosulfate consumption of 23 kg/t-ore for 24 hour’s leaching at ambient temperature. The gold recovery by cementation was nearly 100% by Zn and Al powders at Metal/Au mass ratio of 30, and around 95% by Cu powder at Cu/Au+ mass ratio of 50. In order to oxidize the gold efficiently with the less thiosulfate consumption, the stable region of [Cu(NH3)4]2+ should be as wide as possible in the region, where [Cu(S2O3)2]3- was more stable than [Cu(NH3)2]+. In order to reduce gold from the pregnant solution with the less metal powder’s (Zn, Cu, Al) consumption, the stable region of [Cu(S2O3)2]3- should be wider than [Cu(NH3)2]+ on copper precipitation. Zinc powder may recover gold more efficiently than copper powder with the similar trend on the effect of ammonia, copper and thiosulfate. However, the large amount of copper will be co-precipitated along with gold since the stability of zinc ammine and thiosulfate complexes are higher than that of copper’s. Aluminium may reduce gold efficiently at higher thiosulfate concentration and pH. These results were confirmed and compared with the optimum reagent combination for finer grind sample at 100 mass% -75 µm, which is the optimum ore size for the standard cyanidation at 1.0 g/ l NaCN to obtain about 95% gold extraction. The optimum reagent combination was concluded as 0.5 mol/l NH4OH, 0.0001 mol/l CuSO4*5H2O and 0.05 mol/l (NH4)2S2O3 with the result of 94% gold extraction and 3kg/t-ore of ammonium thiosulfate consumption. Gold and copper stabilities were well agreed with the result of coarser grind ore thermodynamically. The lower reagent combination will reduce gold oxidation power, but significantly minimize the reagent consumption. From this pregnant solution, nearly 100% of gold was successfully recovered by zinc precipitation at Zn/Au+ mass ratio of 30. Aluminium and copper precipitations resulted in less than 40% of gold recovery at Metal/Gold mass ratio of 30. The reagent consumption cost on this lower reagent combination followed by zinc precipitation was $1.6/t-ore, while the cyanidation was $3.1/t-ore. Thiosulfate oxidation mechanism indicated the similarity to Belousov-Zhabotinsky reaction.

Jan 1, 2002

By M. L. Free, L. Anthian

Electrochemical, chemical, and image analysis techniques were utilized together with statistical analysis methods to determine the effect of various anode impurities on copper electrorefining performance. Results indicate that arsenic is a beneficial anode impurity. Anode lead and sulfur are shown to decrease electrorefining performance. Specific emphasis is given to the influence of individual elements on current efficiency, slime particle generation, and cell voltage parameters.

Jan 1, 2000

By Remo Grandori

The Umiray Angat 13,2 km long tunnel in Philippines have been bored through extremely variable and difficult ground conditions including a number of special events. In particular the following adverse conditions were found: faults in decomposed ground, high temperature rocks, extremely rapid and important convergence phenomena, water inflows up to 800 litres per second. The special El Nino climatic conditions caused a long dry season and lower the level of the lake that was granting the access by barge to the site under the minimum navigable level. Many equipment have had therefore to be transported to site by a 10 ton capacity helicopter, after having been partially dismounted. For the same reason most of the tunnel drive have been bored servicing the site by 1 ton capacity helicopters to transport materials, spares and personnel. In order to overcome the above geological and logistic problems several innovation were introduced and tested in this project. Despite all that difficulties the 13,2 km of tunnel were bored in about 24 months, with a global average of 500 m/month.

Jan 1, 2001

By G. R. Robinson

Aggregate resources consist of sand and gravel, and crushed stone. They are large-tonnage, bulk-minable mineral commodities that are used in construction and industrial activities (Tepordei, 1999, 2001).Rates of aggregate production, use and mine permit approval in the mid-Atlantic region differ by population density. These rates are influenced by economic and human factors, such as demand, costs, land availability and community opposition. In some areas, the local availability of aggregate is limited. This is due to the lack of suitable local source materials for aggregate, the loss of potential high-quality aggregate resource production sites by preemptive land development and restrictive zoning (resource sterilization), and the difficulty of developing and permitting production sites for aggregate.

Jan 1, 2004

Two miners were fatally injured when a pillar bump occurred during retreat mining in a southern West Virginia coal mine. The mine was operating in the Eagle seam with overmining in the No. 2 Gas and Powellton seams. A coal bump is defined as a sudden and violent failure of coal caused by the release of stored strain energy in the pillar. While significant strides have been made by academia, industry, and regulatory agencies to better understand bump conditions and mitigation techniques, coal bumps represent a long standing, highly site-specific engineering problem in which the exact failure mechanism(s) is not clearly understood.

Jan 7, 2020

By Ray Brainard

Treated effluent from the Clean Water Coalition (CWC) member agencies is currently discharged at an annual average rate of 6,570 l/s into the Las Vegas Wash, and is increasing annually. As the effluent flow increases, the nutrient loading of the treated effluent will approach the maximum limits allowed under the current regulations. To manage this flow while maintaining water quality in Lake Mead, the CWC is implementing a 44-km-long conveyance system. This paper discusses the geological and geotechnical aspects of the 13.4-km-long tunneled section through the River Mountains and their effect on design. The tunnel alignment traverses a heterogeneous package of volcanic and sedimentary rocks exhibiting widely variable rock conditions.

Jan 1, 2008

Underground mine designs typically try to avoid extraction beneath streams and rivers of any significant size, especially when the overburden rock thickness between the stream bed and the mine is thin. Potential issues with mining beneath streams include excessive groundwater inflow to the mine; weak ground (roof, floor, and pillar) conditions; horizontal stress effects; as well as stream loss and other potential adverse environmental effects. However, there are times when crossing beneath a stream or river is necessary to move into a new area of mineral reserve without creating additional mine access points from the ground surface. Often, stream crossings are completed without thorough assessment, potentially resulting in increased costs, decreased safety, and, in some cases, failure to advance the mine. Selection of the most favorable location(s) to cross the stream must account for numerous factors and the associated assessment often requires a multidisciplinary approach. Stream crossing investigations often require geological, hydrogeological, geotechnical, and geophysical expertise. Phases of stream crossing investigations include desktop evaluation of maps and aerial photography, stream bed observations, drilling, detailed rock core logging, downhole geophysical surveying, hydraulic conductivity testing (packer testing), geotechnical laboratory testing, assessment, and reporting. The deliverables from a stream crossing assessment typically include geological, geotechnical, and hydrogeological characterization of potential stream crossing locations; classification of favorable and unfavorable crossing locations; recommendations for entry design and pillar sizing; and recommendations for if, and how, to conduct pre-grouting activities. Examples of technical aspects of data collection and assessment are provided based on decades of industry experience conducting stream crossing assessments in various underground mining scenarios.

Jul 28, 2020

By Xiaodong Ma, Marek Pawlik

Introduction Guar gum is a natural nonionic polysaccharide. Guaran, the functional polysaccharide in guar gum is a chain of (1?4)-linked ß-D-mannopyranose units with a-D-galactopyranose units connected to the mannose backbone through (1?6) glycosidic linkages. The poly-mannose chain is randomly substituted with galactose units at a mannose-to-galactose ratio of 1.8-1.0 [1]. Cheng et al. reported that the molecular weight of natural guar gum is 1.935 • 106 [2]. Robinson et al. found that the molecular weights of five grades of commercial guar gums ranged from 4.4 • 105 to 16.5 • 105 [3]. Guar gum is frequently used as a depressant of naturally hydrophobic gangue minerals (e.g. talc) in the flotation of PGM-bearing ores, and according to Harris et al. a wide variety of modified guar gums are available for this application [4]. The Canadian potash industry utilizes natural guar gum as a blinder of water-insoluble slimes in the flotation of potash (sylvinite) ores, a process that is carried out in a saturated KCl/NaCl brine. The role of the polysaccharide is to prevent a primary amine collector from adsorbing onto these unwanted fine minerals. Hydrophobic interactions between basal cleavage planes and the polymer appear to be involved in guar gum adsorption on talc [5,6]. Liu and Laskowski stressed the importance of metal impurities on mineral surfaces that can serve as the active sites for polysaccharide adsorption [7]. This postulate was consistent with the later observation that, in addition to hydrogen bonding, the adsorption of guar gum onto talc was strongly dependent on the surface concentration of magnesium sites [8,9]. In this case the adsorption process was visualized as metal-polysaccharide complexation facilitated by the cis-configuration of the hydroxyl groups of mannose monomers. Hydrogen bonding and chemical interactions with metal sites were also suggested by Rath and Subramanian in their studies on guar gum adsorption on biotite mica [10]. In a recent study, Wang et al. demonstrated that hydrogen bonding is the main driving force behind guar gum adsorption onto talc [11]. Their data also show that the adsorption density of guar gum on alumina is about five times lower than the adsorption density on talc. Pawlik and Laskowski reported that the amount of guar gum adsorbed on illite was independent of ionic strength over a wide range of salt concentrations [12]. The adsorption density of the polysaccharide on illite did not measurably change with ionic strength from that of distilled water to about 50%-saturated KCl/NaCl potash brine (~3N KCl/NaCl). However, guar gum adsorption on dolomite dramatically decreased over the same range of ionic strengths, and no reliable explanation of that phenomenon was proposed [12]. The water structure-breaking or structure-making capabilities of background ions are usually ignored when discussing adsorption mechanisms of polymers. The concept of “structure breakers” and “structure makers” was first introduced by Gurney, and Frank and Wen who postulated that each ion is surrounded by three distinct regions of water structure [13,14]. In the first layer, water molecules are tightly bound to the ion. The second region extends farther away from the ion and is referred to as the region of structure breaking. Only at larger distances, where the ionic field is weak, water molecules form the “normal” ice-like structure. It is also now recognized that the first layer can be further divided into the primary and secondary hydration shells. Small, strongly hydrated ions reinforce the “normal” structure of water and the region of structure breaking disappears. In contrast, large less-hydrated ions disturb the ice-like structure and generate an extensive region of structure breaking. Experimentally, these two effects can readily be distinguished through viscosity measurements. Increasing concentrations of structure-breaking ions result in a decrease of the viscosity of aqueous solutions. On the other hand, increasing amounts of structure-makers significantly reduce the viscosity of water. Alkali metal cations form a sequence known as the Hofmeister series. The Hofmeister series - Cs+, K+, Na+, Li+ - orders the cations from the least hydrated to the most hydrated. Based on literature viscosity data for aqueous

Jan 1, 2005

By Charlie Yates, Max Ramey, Kurt Nielsen, Michael Hardy

The Yankee Gulch sodium minerals project (YGP) is a solution mining project operated by American Soda. The mine operates on a federal lease administered by the U.S. Bureau of Land Management (BLM). Commercial operations began in November2000. In 1964, Irv Nielsen discovered nahcolite mineralization where the YGP pilot plant is now located near the Piceance Creek in Rio Blanco County, Colorado (Nielsen, 1969).Development of the project accelerated after Williams Corp., of Tulsa, OK, joined with American Alkali in1996 to form American Soda. Pilot testing by American Soda led to commercial permitting, plant design, construction and startup. Figure 1 shows the location of the Yankee Gulch leases and the location of the upper and lower plant sites.

Jan 1, 2003

By Bill Cain, David F. Tsztoo, R. John Caulfield, D. Scott Kieffer

In 1994, the East Bay Municipal Utility District (EBMUD) commenced a system-wide Seismic Improvement Program to protect their facilities from catastrophic damage. A primary focus of this program has been on retrofitting the 75-year old Claremont Tunnel, which crosses the active Hayward Fault zone. A large earthquake on the Hayward Fault could generate enough right-lateral fault slip to effectively sever this important lifeline. The retrofit project involves construction of a new bypass tunnel through the Hayward Fault zone, together with systematic contact grouting and localized structural repair of the existing concrete liner. Several innovative design measures have been incorporated into the seismic retrofit design, including an oversized tunnel cross section, backfill concrete side drifts, seismic isolation of an internal structural pipe, and shear fuses in the final lining.

Jan 1, 2005

By Brain E. Gombos

The Allen Park Sanitary Sewer Overflow (SSO) Tunnel and relief sewer project, located in the city of Allen Park, MI, is a long-term corrective action designed to bring Sanitary District One?s sanitary system into compliance with its 2005 consent order and service contract with the Detroit Water and Sewerage Department (DWSD). The $20 million project is intended to reduce Allen Park?s wet weather discharges to DWSD, reduce bypass pumping to the Ecorse Creek and limit the future risk of basement flooding by providing storage during wet weather events and eliminating hydraulic bottlenecks in the sanitary sewer system.

Jan 1, 2013

By K. Y. Haramy, K. Hanna

Early identification of adverse geologic conditions and high stress concentrations during the high-speed extraction of coal using modern mechanized longwall systems is a major challenge facing the mining industry. Often, unexpected geologic anomalies that affect rock mass quality are encountered more rapidly, leaving the mine operator with insufficient time or information to deal with the changing ground conditions. The RockVision3D™ seismic tomographic system, developed by NSA Engineering, Inc., offers substantial benefits over conventional geologic/stress-detection methods and has been used successfully in coal mines worldwide. Tomographic images, produced economically and in near-real time, are easy to interpret, allowing mine operators to deal with potential hazards on a day-to-day basis.

Jan 1, 1999

By D. M. Weinberg, S. R. Novascone, R. R. Reynolds, J. H. Cole, C. D. Christensen

The mechanical properties of the rocks surrounding an orbital vibrator alter the shape and amplitude of the vibrator’s orbit. Detecting these changes with driving point impedance measurements promises to reveal fractures and, possibly, identify the in situ stress state and significantly increase the depth that can be investigated. Our research emphasis has been on detecting vertical fractures through casing. Experimental and numerical results to date indicate that our new logging tool has excellent potential for determining both the vertical extent and azimuthal orientation of such fractures. Fracture and in situ stress orientations are useful in mine planning.

Jan 1, 2002

By T. J. McKeon

Partition curves are used to evaluate the separation performance of gravity-based concentrators. The partition curve is used to identify the nominal density cutpoint and relative sharpness of the separation. In addition, the graphical representation makes it possible to quickly identify the root cause of misplacement based on the characteristic shape of the partition curve. Partition curves have been traditionally constructed using data obtained from float-sink tests using heavy organic liquids. These toxic liquids are environmentally unfriendly and have been banned in several countries. Another method of establishing the partition curve is to introduce density tracers into the feed and plot the distribution to the lights and heavies. For heavy mineral separations, this approach is generally impractical due to the fine particle size. In addition, the partition data obtained using these existing techniques do not account for secondary factors such as particle shape that may influence the separation. In light of these problems, a methodology was developed for constructing partition curves using experimental data obtained from microscopic grain-counts. This technique, which essentially uses the different mineral species as density tracers, provides a powerful tool for evaluating heavy mineral separations. A case study is provided to demonstrate how this analytical approach can be used to assess and improve the separaton performance in an industrial upgrade plant.

Jan 1, 2005

By G. Duncan, K. Winther, R. Ericsson

Distinct trends in grinding mill technology have emerged in recent years. In an effort to optimize overall mill performance for the needs of the End User, broad measures of logistical speed, process flexibility, operational risk, and overall costs now exert greater influence on the specification of grinding equipment. As a result, innovative alternatives to conventional grinding mill structures, supports, drives, feed, and discharge configurations are now being offered and selected with greater frequency. This paper investigates these trends in grinding mill technology, utilizing optimization and decision-theory techniques. In particular, the paper considers how specific advances in process design, product engineering, manufacturing techniques, and mining operations continue to relax technological constraints, enabling further mill innovation. In this context, a methodology is presented, illustrating how proper selection and specification of grinding mill components and configuration can target an optimization of the four End-User performance measures listed above.

Jan 1, 1999

This paper was developed as part of an effort by the National Institute for Occupational Safety and Health (NIOSH) to identify risk factors associated with bumps in the prevention of fatalities and accidents in highly stressed, bump-prone ground conditions. Changes of failure mechanism with increasing confinement, from extensional- to shear-dominated failure, are widely observed in the rupture of intact specimens at the laboratory scale and in rock masses. In the previous analysis conducted in 2018, both unconfined and triaxial compressive tests were conducted to investigate the strength characteristics of some specimens of a Utah coal, including the spalling limits, the ratio of apparent unconfined compressive strength (AUCS) to unconfined compressive strength (UCS), the damage characteristics, and the post-yield dilatancy. These mechanical characteristics were found to be strongly anisotropic as a function of the orientation of the cleats relative to the loading direction.

Jan 7, 2020

By D. Bedell, J. Robitalle, D. Macgilliveray

Agnico Eagle (Cadillac Quebec, Canada) selected the new Eimco PEC E – CAT™ clarifier thickeners for their counter-current decantation circuit, which handles approximately 200tph leached gold/silver ore. The E-CAT is based on rakeless ultra-high rate thickening technology that originated in South Africa. Four 9m diameter and two 10m EIMCO E – CAT ultra high rate, rakeless thickeners were installed in the fall of 2000. Thickening and clarification performance has been excellent. Problems with level control have been resolved and the plant personnel continue to improve the operating control techniques. The CCD circuit is critical to the success of the operation and good recovery. Data will be presented showing the wash ratios and recovery achieved. A brief history of the operation and the decision to utilize the CCD system will be presented.

Jan 1, 2002