Search Documents

By M. E. Ryan, C. L. Hoebbel, E. J. Haas

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of any company or product does not imply endorsement does not constitute endorsement by NIOSH. ABSTRACT It has been suggested that effective disaster prevention and response in mining requires that elements of emergency management be incorporated into everyday operations, planning, and decision-making, much in the same way that the industry approaches routine risk management. Since Congress passed the MINER Act in 2006, the newly mandated structural and technological advancements in mine emergency response preparation have been made and are apparent, but measureable improvement in mineworker emergency preparedness is difficult to ascertain. To begin exploring whether measurable indicators of mine workforce preparedness can or should be addressed within a risk management framework, NIOSH researchers examined the datasets from two separate research efforts—one which measured the organizational safety climate and self-reported safety performance, and the other which measured individuals’ perceptions of their own self-escape competency. INTRODUCTION In response to the mine disasters in 2006, the United States Congress passed the Mine Improvement and New Emergency Response Act (MINER Act), which strengthened existing regulations [30 CFR, Part 48] and introduced new provisions to improve mine emergency response. Since that time, new technological and structural features, such as mandated redundant communication systems, personnel tracking systems, and lifelines in primary and secondary escapeways, have been installed in underground coal mines across the country. Additionally, mine operators are required to develop emergency response plans, provide adequate supplies of breathable air throughout the mine, provide more frequent and realistic expectations training, and are required to immediately notify the Mine Safety and Health Administration (MSHA) in the event of an accident. While the structural and technological advancements in emergency preparedness are readily observable and easily measured, levels of individual mineworker preparedness remain difficult to assess. There is a general consensus that deficiencies in competence in the non-routine tasks required for individual miners to effectively respond to a mine emergency likely remain (e.g., National Research Council [NRC], 2013), and NIOSH research continues address this concern (Haas, et al., 2015; Hoebbel et al., 2018). To maximize an operation’s capacity to effectively prevent disasters and/or respond to emergency events, it has been suggested that individual and emergency management efforts be incorporated into everyday operations, planning, and decision-making in much the same way organizations manage routine risks to health and safety (Haddow et al., 2017). To the authors’ knowledge, the mindful intersection of routine risk management policies and practices and emergency prevention and response readiness have yet to be empirically studied within the mining industry.

Jan 1, 2019

By J. P. Allen

Cobalt, nickel, and manganese can be recovered quickly, cleanly, and selectively from cobalt-rich manganese crust by leaching in dilute acid solutions in the presence of hydrogen peroxide. Common selective precipitation methods can then be used to recover these metals from the leach liquor. The leaching reaction produces only oxygen as a byproduct, and the waste residue from leaching was tested and found to be non-hazardous under existing EPA specifications. The leaching process is effective in either fresh water or seawater. This research is a part of the Bureau of Mines program to identify the mineral resources of the Exclusive Economic Zone and devise methods for recovering their valuable components.

Jan 1, 1990

By R. L. Summers

The tremendous engineering advances occurring during this past century are very evident within the boundaries of the Anthracite Section of AIME. The Steelton plant of Bethlehem Steel Corporation, located along the Susquehanna River just east of the Commonwealth's capital at Harrisburg, for more than 105 years has experienced a most dynamic life which has paralleled America's industrial growth. (Figure 1) In June 1865, just after the Civil War, a group of men met to organize the Pennsylvania Steel Company. The war had brought into sharp focus the vital importance of the railroads to the country's expansion. Until that time wrought iron rails were used, and the replacing of track after only several months wear had become an almost unbearable cost. The spirit of free, competitive enterprise and the prospects of a lucrative market compelled these men to form that first Pennsylvania Steel Company and to develop better rail products. They issued the following statement: "...our desire to free ourselves from dependence upon a foreign market (has) led to the organization of the Pennsylvania Steel Company, and the parties who have connected themselves with it are determined to produce upon American soil all the principal manufactures of steel that are now, at such a serious cost for freight, commission, insurance, exchange, duty, etc., and often, with so much delay and uncertainty, imported from abroad. (We) are preparing to establish near the consumer, works at which articles of accustomed pattern will be promptly produced, and from the

Jan 1, 1971

By Charles O. Frush

This paper presents a summary of the current employment practices with respect to recent graduates in Mining Engineering, as observed at the Colorado school of Mines. Because our experience is limited to our own group of students it prob¬ably does not correspond exactly to that experienced at other mining schools, but because the Colorado School of Mines graduates approximately 15 per cent of the men in this field our experience is probably representative. We have chosen to limit the information presented here to that pertaining to the period since July 1, 1960. This corresponds to the experience with the class of 1961 and to the experience of the class of 1962 up to the end of the first semester of the senior year. There were 36 mining engineering degrees given in 1961 In a class numbering 43 senior. We expect to give 30 first degrees in 1962 in a class numbering 44 seniors.

Jan 1, 1962

By A. Arik

Reliable ore reserve estimates for deposits with highly skewed grade disributions are difficult tasks to perform. Although some recent geostatistical techniques are available to handle problems with these estimations, ordinary kriging or conventional interpolation methods are still widely used to estimate the ore reserves for such deposits. The estimation results can be very sensitive to the search parameters used during the interpolation of grades with these methods. This paper compares the ore reserve estimates from ordinary kriging using several cases in which certain search parameters are varied. The comparisons are extended to different mineralizations to show the changing effects of these parameters.

Jan 1, 1990

By Wilson W. Zoogah, Joel G. Burken, Abdullah Al Moinee, Mariam K. Al-Lami, Kwame Awuah-Offei

Soil CO2 flux serves a critical indicator of ecosystem function and carbon cycling in disturbed landscapes. This study measured and quantified temporal patterns and environmental drivers of soil respiration across fifteen revegetated treatment plots over a 12-week period (July-October 2025). Utilizing automated CO2 flux measurements, we investigated differences between treatments and quantified their relationships with soil temperature, moisture, and atmospheric pressure. One-way ANOVA revealed significant treatment effects on CO2 flux (F4, 442 =14.1, p < 0.001, η2=0.113), with amended plots exhibiting 40–50% higher mean fluxes than control plots. Weekly temporal analysis demonstrated distinct temporal patterns, with peak fluxes registering in mid-August before a gradual decline. Multiple regression analyses showed that soil temperature (β=0.043, p < 0.001) and moisture (β=2.31, p < 0.001) are the primary flux drivers, together accounting for 18.2% of total variability (adjusted R2=0.182). Atmospheric pressure had a moderate effect (β=1.13, p < 0.001), detectable only in multivariable analysis. Variance partitioning indicated that environmental factors explained more variability (18.7%) than treatment effect (10.5%), with approximately 71% of flux variability attributed to finer spatial or temporal variability. These results demonstrate that revegetation amendments enhance soil biological activity and impact geochemical cycling, and that temperature and moisture are dominant controls on respiration dynamics in reclaimed mine soils. The findings provide quantifiable benchmarks for ecosystem recovery through altering soil biology and geochemistry and for quantifying carbon sequestration potential in post-mining landscapes.

Feb 22, 2026

By Isa Nozari, Asghar Azizi

The extraction of copper from sulfate leaching liquor was investigated using Acorga M5640 commercial extractant in kerosene diluent. The effects of important factors such as the extractant concentration, contact time, liquor pH, and temperature were examined on the separation factor Cu/Fe and the extraction efficiency of copper. The results indicated that nearly 92.32% copper was extracted from the leach liquor at 10% (v/v) Acorga M5640 concentration, 1:1 aqueous/organic phase ratio, 20 min contact time, pH 2.5, and 25 °C temperature. Also, the further increase in the values determined had no positive impact on the extraction of copper. Under these conditions, the separation factor Cu/Fe was obtained about 29.64. The extraction mechanism was studied applying the plot of log(D) – 2 pH against log [extractant] and it proved the association of two moles of Acorga M5640 for the extraction of one mole of copper. McCabe–Thiele diagram was constructed and a single-step extraction process was found to obtain themaximumextraction. Additionally, thermodynamic datawere investigated and the extraction process was endothermic and non-spontaneous at 298 K (ΔH = 27.05 and ΔG = 15.52 kJ mol−1). Moreover, the loaded organic phase was stripped and 80.94% copper was recovered after 20 min using 10% sulfuric acid concentration.

Jul 31, 2020

By H. EI-shall

Bench top centrifuge is used to study the consolidation behavior of phosphatic clays. A mathematical model (based on first order kinetics) is developed to describe the relationship between the void ratio (at any time) and the effective stress. Permeability of the sediment as a function of the void ratio is also described. The obtained data are compared with that obtained by other consolidation testing methods. Centrifuge results indicate that consolidation data may be developed in a short period of time (hours) as compared to days or weeks when other techniques are used.

Jan 1, 1995

By M. L. Free, N. Dhawan, M. S. Safarzadeh, J. D. Miller, M. S. Moats

"The drum agglomeration of nickel laterite and gold ores has been optimized through the design of experiments (DOE) using a Taguchi L16 (45) orthogonal array to determine the optimum conditions for maximizing average agglomerate size and minimizing the amount of fines. The effects of controllable operating factors including moisture content (nickel laterite ore: 34-37%; gold ore: 7-10%), retention time (2-3.5 min), drum speed (15-45% critical speed), drum load (nickel laterite ore: 8-32 %; gold ore: 6-22%) and acid concentration (150-600 g/L) on the performance of the agglomeration process were studied.For nickel laterite ore, maximum average agglomerate size and minimum percent fines (-1 mm) occurred under the following conditions: drum load (23.7%), moisture (36.5%), time (3 min), drum speed (30% critical speed) and acid concentration (150 g/L). Under the studied nickel laterite ore conditions, the most effective parameters for maximizing average agglomerate size and minimizing the amount of fines were found to be drum load and acid concentration, respectively. Drum speed had a statistically significant effect on minimizing the amount of fines. Maximum average agglomerate size and minimum percent fines (-1 mm) for gold ore occurred under the following conditions: drum load (19.3%), moisture (8.5%), time (2 min 15 s) and drum speed (40% critical). The most significant factors for maximizing average agglomerate size and minimizing the amount of fines for gold ore were found to be drum load, time and moisture.IntroductionSeveral heap leach operations have experienced problems in terms of poor recovery due to percolation issues caused by low-grade complex ores, tailings and clayey deposits. Poor percolation can lead to low metal extraction due to solution channeling or the development of impermeable/dead zones within the heap (Dhawan et al., 2012; Kappes, 2005). Improper heap building practices such as the use of loose agglomerates and inadequate attention toward the presence of clay minerals have been among the main reasons for percolation issues. During the transport of ore material, severe segregation of the material can occur. To overcome percolation problems, a major improvement was made through the introduction of agglomeration prior to ore placement. If the ore particles and agglomerates are of similar size, segregation can be avoided to a great extent (Dhawan et al., 2013; Kinard and Schweizer, 1987; McClelland and van Zyl, 1988). Agglomeration improves the uniform percolation of solution through ore heaps and is applicable to many ores, wastes and milled tailings (Bouffard, 2005; Dhawan et al., 2013). Manning and Kappes (2005) reported agglomeration/ stacking accounts for ~14% of the total heap leaching operating cost. The cost of binder is a primary contributor toward the total cost. Also, the lack of consistent quality control tests for agglomerate often leads to operational problems. The details are mentioned elsewhere (Dhawan et al., 2013). Considering the significant contribution of the agglomeration/stacking step toward the total heap leach operating cost, it is appropriate to study the agglomeration behavior and its optimization for two different ores. The reason to study the same parameters for different ores is the fact that significant variability in the agglomeration behavior of different ores has been reported to exist in industrial operations."

Jan 1, 2015

By Louis M. Schlesinger

KMG Minerals, Inc., a mica-feldspar-quartz producer in Kings Mountain, N.C., uses about 50% of its plant&apos;s -200 mesh slimes to manufacture brick. However, the company is unable to market the remaining 50% of this fine mineral mixture. The NCSU Minerals Research Laboratory operated a pilot plant to process these slimes to produce an additional product. The process, consisting of blunging and hydraulic sizing, was designed to separate a kaolin-enriched -270 mesh product from the bulk of the coarser +270 mesh "grit" minerals. Size analysis showed that this product was 80% finer than 20 microns and 50% finer than 6 microns (in equivalent spherical diameter). An evaluation indicated that it is a hydrous aluminum silicate that might be suitable in the filler and extender markets for traffic paint, some types of plastics, joint cements, and dusting compounds. Because of its high viscosity, it will be difficult to use more than a small percentage in cast ceramic bodies. However, it might be possible to use up to 10% in extruded ceramic bodies (i.e., electrical porcelain). The 15.2 cm (6 in,) diameter Linatex Hydrosizer was tested using a range of teeter water flowrates, so that the net rise velocity was varied from 0.10 cm/s to 0.40 cm/s. The solid feed rate to the sizer was maintained at approximately 1.1 t/hr/m2 (0.12 ton/hr/ft2). Tests were run using both "shallow" (i.e., 6 in.) and "deep" (i.e., 15 in. teetered beds. The best overall result was obtained when the sizer was operated with the "deep" teeter bed and a net rise velocity of 0.10 cm/s. About 97% of the +270 mesh material was rejected and approximately 79% of the -270 mesh material was recovered in a 14% solids slurry.

Jan 1, 1994

By R. J. Roman

The "mass balance" is unquestionably the most common class of problems for the process engineer&apos;. Closely related, mathematically, is the "heat balance". Every laboratory test requires a mass balance to describe the results. Mass balance calculations can be subdivided into several sub-categories based on whether the results are time dependant or not and depending on whether the input data are measurements that contain errors or are hypothetical values with no errors. Time dependent mass balances are dynamic process simulations and in addition to the conservation of mass constraints require kinetic data input. They are one step beyond simple mass balances.

Jan 1, 1992

By Manoj Khandelwal, Bright Akuinor Tsidi, Newton Amegbey, Daniel Mireku‑Gyimah

One of the ambient effects of production blasting is flyrock. To effectively manage flyrock throw distance in mining, there is the necessity to successfully envisage blasting output without sacrificing the hazardous impact of flyrock which may result in fatality and operational shutdown. For flyrock throw distance prediction, velocity of detonation (VOD) and charge per bank cubic meter (CPBCM) are not usually included. This paper focuses on the use of support vector machine (SVM) regression to ascertain the impact of VOD and CPBCM on flyrock throw predictions. The machine learning models were linear support vector machine (LSVM), quadratic Gaussian support vector machine (QGSVM), fine Gaussian support vector machine (FGSVM), medium Gaussian support vector machine (MGSVM), and cubic Gaussian support vector machine (CGSVM). The outcome indicates that FGSVM was the most sensitive with a 4% improvement when VOD and CPBCM were included. As a result, the LSVM model provides a suitable AI competitive alternative tool for flyrock throw prediction in mining operations by incorporating VOD and CPBCM.

Feb 10, 2024

By R. Rodgers

The Pinto Valley concentrator of BHP Copper Inc. restarted its sulfide mining operations in September 2007 to produce copper and molybdenum concentrates. During the plant production ramp up, the copper/molybdenum circuit quickly reached the copper grade and recovery targets, but the production and quality of the molybdenum concentrate continued to be a challenge. Even though several improvements in the molybdenum circuit were completed, the final molybdenum concentrate did not meet contractual specifications. After reviewing several options to improve grade and reduce contaminants, the installation of three flotation columns were chosen. The column design and construction were done using in-house craftsmen and engineers. Ten days after commissioning, the columns successfully reached a steady operation and began producing molybdenum concentrate to the required specifications, that is, high molybdenum tenors and low copper and iron content. The Pinto Valley operations, are comprised of the Pinto Valley concentrator, the Pinto Valley dump leaching and a solvent extraction/electrowinning (SX/EW) plant. The concentrator operated from 1972 to 1998 when mining and milling operations were curtailed for economic reasons. The SX/EW plant continued operations for copper cathode production. After a cessation of mining operations of almost 10 years, Pinto Valley operations began a restart project in January 2007, to bring the mine and the concentrator back into production. Copper concentrate production started in October 2007 after refurbishing and upgrading the facilities with a new DCS system and filter plant. The daily targets of the concentrator were to treat 56.7 kt (62,500 st) of ore, produce 762 t (840 st) of copper concentrate containing 27.5 percent copper at recoveries of 86 percent and produce 2.2 t (2.5 st) of molybdenum concentrate containing more than 80 percent MoS2.

Jan 1, 2010

By D. R. Wilburn

his summary of international mineral exploration activities for the year 2011 draws upon available information from industry sources, published literature and U.S. Geological Survey (USGS) specialists. The summary provides data on exploration budgets by region and mineral commodity, identifies significant mineral discoveries and areas of mineral exploration, discusses government programs affecting the mineral exploration industry and presents [ ] analyses of exploration activities performed by the mineral industry. Three sources of information are reported and analyzed in this annual review of international exploration: 1) budgetary statistics expressed in U.S. nominal dollars provided by Metals Economics Group (MEG) of Halifax, Nova Scotia; 2) regional and site-specific exploration activities that took place in 2011 as compiled by the USGS and 3) regional events including economic, social and political conditions that affected exploration activities, which were derived from published sources and unpublished discussions with USGS and industry specialists.

Jan 1, 2012

Industry and regulatory agencies have requested guidance on safe blasting near transmission pipelines. The U.S. Bureau of Mines and AMAX Coal Company have studied surface coal mine overburden blasting near four steel and one PVC pipe-line of 15 to 5l-cm diameter, monitoring vibration, strain, and pressure. Unlike tests simulating construction blasting, these were up to 1000 kg per delay in 3l-cm blastholes. Worst case comparisons showed that 12.7 cm/s blasting vibrations produced strains about 1/4 that of pressurization and 10-18 pct of the ultimate tensile strength. No failures occurred from blasting as close as 15 m which produced vibrations over 60 cm/s.

Jan 1, 1994

By PEILIN LAN, LEONARD HILL, SIMON TIMBILLAH, BERNARD FOSU, CESAR SOSA-BLANCO

The use of sodium hydrosulfide (NaHS) in most of the operations in by-product molybdenum flotation comes with safety concerns and, in some instances, a high reagent cost. Engineered solutions at the various operations where NaHS is used have reduced the possibility ofH2S gas evolution immensely. However, the threat of exposure remains, and this, coupled with the high dosages of NaHS consumed, supports the continued search for alternative depressants. This paper focuses on efforts to study the applicability of disodium carboxymethyl trithiocarbonate (DCMT), an organic depressant, as an alternative to NaHS. Benchscale rougher flotation results for samples from the Sierrita Cu–Mo plant showed the best DCMTperformance at 8 kg/t of DCMT and pH=10.5 with 30 min of shear conditioning and 10 min of flotation conditioning time. The Aminpro plant model simulation confirmed that DCMT with 4–8 kg/t under certain shearing and conditioning times achieved superior or equivalent Mo–Cu separation efficiencies when compared to NaHS.

Apr 19, 2021

By R. J. Roman

The results of column leaching tests on 3 different mixed oxide/sulfide ores from a Chilean deposit are presented. The 3 samples contained different ratios of oxide copper minerals to chalcocite and chalcopyrite. The results of the column leach tests are interpreted in light of the shrinking core model for coarse particle leaching. The copper recovery from the oxide minerals and the sulfide minerals each conforms to the shrinking core model with the total recovery equal to the weighted average of the individual minerals. The use of column test results to predict field heap leaching results using the multi-mineral shrinking core model is discussed.

Jan 1, 1993

By Scott Rosenthal, Dave Gilkey, Theresa Stack, Daniel Autenrieth, Ciara Kremer

Jackleg drill operators are exposed to harmful levels of hand-arm vibration (HAV). Anti-vibration handles and gloves provide modest reductions in HAV exposures and forearm muscle exertion from the use of anti-vibration handles and gloves by jackleg drill operators. The goal of this pilot study was to investigate changes in HAV with the use of anti-vibration gloves and handles compared to forearm muscle exertion experienced by operators and measured with surface electromyography (EMG). Five subjects operated the drill under four different cases: no anti-vibration controls, anti-vibration gloves only, anti-vibration handle only, and simultaneous anti-vibration handle and glove use. Muscle exertion was expressed as a percent of maximum voluntary contraction (%MVC) and was compared using Welch’s ANOVA with Games-Howell post hoc comparisons. The case with both anti-vibration controls in use simultaneously (largest grip diameter) was associated with a mean %MVC of 36.13% during operation for all forearm muscles combined, which was significantly higher than that of the other cases (p < 0.05). There were no statistically significant differences in mean HAV exposures. The anti-vibration handle with anti-vibration glove case only increased the maximum allowable exposure time by 8 min as compared to the control case without any anti-vibration controls. These results suggest that the modest HAV exposure reductions from the use of anti-vibration handles and gloves may pale in comparison to the increased muscle exertion resulting from their use, and this trade-off among jackleg drill operators is a potential concern that warrants further investigation.

Jul 12, 2021

By R. E. Murray

"It is a gloomy moment in the history of our country. Not in the lifetime of most men has there been so much grave and deep apprehension; never has the future seemed so incalculable as at this time. The domestic economic situation is in chaos. Our dollar is weak throughout the world. Prices are so high as to be utterly impossible. The political cauldron seethes and bubbles with uncertainty. Russia hangs, as usual, like a cloud, dark and silent, upon the horizon. It is a solemn moment. Of our troubles, no man can see the end." By now you, no doubt, are asking, &apos;Where did Murray get this bit of philosophy?&apos; Well, I obtained it from an editorial entitled. "The Worst of Times", which was published in the Harper&apos;s Magazine in 1847. That&apos;s right, 1847! The parallelism between the situation in our country at this time and in 1847 is un- canny. But wait, there is one major exception the size of government. To my knowledge, the citizens of 1847 were not stifled by the extreme governmental excesses that we are experiencing today.

Jan 1, 1980

By W. L. Price

I. INTRODUCTION Today, there are two conflicting trends facing the designer of the bulk material handling system. The first trend is the necessity to stockpile increasingly larger amounts of bulk material (coal, ore, stone etc.) as economically as possible. Fig. 1 illustrates such a typical large storage pile. The second trend is the increasing awareness of the ecological problems of today manifesting itself in a new concern over possible air pollution from storage pile surface particles. The conflict between these two trends can become dramatic when this bulk storage pile is located near a heavily populated area. Strong winds can easily create a severe local problem by blowing the particles from the pile surface toward residential and commercial areas, igniting a crisis in public relations. (2), (3), (4). To help define our combined subject and ecological culprit more accurately, Fig. 2 shows the commonly accepted size range of dust particles. A descrip¬tion of the present state-of-the-art of dust control for large storage piles is the intent of this paper. II. OPEN STORAGE PILE SYSTEMS - ALTERNATE CHOICES AND RELATIVE COSTS In discussing the open storage dust problem and possible solutions, one obvious question arises - what are the economics of placing large bulk storage under cover? Part or this answer will be found in Fig. 3 - an approximate unit capital cost comparison between several methods of storage. It will be noted that the cost curve(s) for the closed concrete silo storage illustrated in Fig. 4 is cheaper per ton at relatively small tonnage capacities, but as tonnage increases, the open pile storage unit cost (B) becomes more economical. Curve (T) covers the cost of open storage using the plow feeder arrangement shown in Fig. 5. A gravity draw-down pile with feeders at the base as shown in Fig. 6 represents yet another open storage choice.

Jan 1, 1972