Search Documents

By Don Rose

INTRODUCTION A number of tunnels supported and permanently lined by steel-fiber-reinforced shotcrete (SFRS) have been built in North America in the 1980s. The material is more economical than, and technically equal or superior to, conventional shotcrete using wire mesh. The design and construction of SFRS-lined tunnels is straightforward, and only a few new design principles, laboratory tests or construction equipment modifications appear necessary in order to use this material. Modern tunnel Contractors may use cyclic drill-and-blast methods on some tunnels, with intermittent shotcreting as part of an orderly cycle. The Dry Mix method is most suitable for cyclic, intermittent, relatively small-scale shotcreting. However, modern Contractors excavating tunnels continuously using large long Tunnel Boring Machines (TBMs) or Roadheaders may prefer Wet Mix shotcreting on a mass production basis. In either case, the use of steel-fiber-rein¬forced shotcrete (SFRS) promotes the rapid and economical excavation of tunnels. The addition of microsilica will improve SFRS properties and reduce rebound, and is expected to become standard practice with SFRS in North America, as it now is in Scandinavia. HISTORICAL REVIEW Steel-fiber-reinforced shotcrete (SFRS) at the present time (1985) is essentially conventional shotcrete with straight or deformed steel fibers added, and in general SFRS for tunnel linings encounters the same problems that conventional shotcrete does. Shotcrete history is well known. The use of sprayed plaster on wire frames for mounting animal skins by Carl Akeley of the Smithsonian

Jan 1, 1985

By William Connell

NFPA 502, Standard for Road Tunnels, Bridges and Other Limited Access Highways establishes minimum fire protection and fire life safety requirements for road tunnels, bridges and other roadways where access by emergency responders is physically limited. The 2008 edition of NFPA 502 represents the Technical Committee?s consensus of current best practice for fire protection and life safety requirements for road tunnels, bridges and similarly limited access highways. Research of national and international test programs, design guidelines and regulating standards was per-formed and considered in an effort to establish a singular, comprehensive document representing a recognized base threshold of fire safety in these type facilities. This paper provides an overview of the more significant revisions including the application of fixed fire suppression systems, guidance on tenable environment, protection of structure and dangerous goods transport.

Jan 1, 2008

By Donald E. Raab, Lee W. Saperstein

INTRODUCTION The Premise Not much time has to be spent in a tunneling project to realize the tremendous interdependence that exists among the various unit operations. The research that is to be described attempts to examine one set of these linked operations, namely, the effect of cutters on muck handling properties. All too often research focuses on too minute an aspect of a problem for the results to be of much immediate, practical use. The goal of this research is to avoid this specificity. Apologies are tendered if this goal is missed. It is known that the mode of flow of bulk solids under the influence of gravity -- emptying a bin or hopper -- is dependent on several basic parameters. The size of the particles and the distribution of sizes (consist) determine whether the solids will first flow out of a given aperture; the cohesion of the solids will determine if flow will continue after the bin is opened; and the angle of internal friction determines the size of the flow regime (1,2,3). It is well understood that the latter two parameters affect the behavior of bulk material on a conveyor belt. Cohesion of material to a belt is always an undesired problem. Heaping of material on a belt depends on the material's internal friction. It is also known that varying the particle size, and the packing density of the material can affect the material's angle of internal friction (4,5). The question was posed whether sufficient variation in a mechanical tunneling machine's (mole) cutting function could be arranged to affect materially the handling properties of the muck

Jan 1, 1974

By K. Awuah-Offei

Energy efficiency has become significant due to cost and environmental considerations. Comminution and material handling have been identified as the two most energy intensive processes in mining. The objective of this work was to evaluate truck-shovel energy efficiency strategies using discrete event modeling. Energy audits and time and motion studies were conducted at a surface coal mine to acquire data. A discrete event simulation model of truck-shovel operations was built in Arena® and validated with the field data. The model was used to evaluate the effect of using a larger shovel, and optimizing truck-shovel matching on fuel efficiency. The results indicate that using a larger excavator increases the fuel efficiency of the operation while optimizing truck-shovel matching does not. However, using a larger shovel will lead to under-utilization of the shovel. This work shows the potential benefits of using discrete event simulation to model energy efficiency of mining operations.

Jan 1, 2012

By Morris T. Worley

Editor’s note: Mining companies doing business in Central Asia, and parts of the developing world, should look for ways to promote community development through the introduction of appropriate technology. This article should be of interest to SME members. It shows sustainable development type projects need not be massive or expensive. Smaller, utilitarian projects are equally valuable to developing communities as they seek to develop their own economic and social infrastructures. Joint Development Associates International (JDA) began humanitarian relief and community development in Central Asia in 1992, following the collapse of the former Soviet Union. Appropriate technology has played an important role in the company’s efforts to assist those segments of society that are most vulnerable to poverty and disease.

Jan 1, 2005

By Duane A. Smith

They are gone now. Gone like that long ago generation that gave them birth. The Homestake Mine, nestled in the northern Black Hills, closed in 2001 after 125 years, the longest run of any major American gold mine. The Homestake Mining Co., which guided its destiny for those many years, is gone too. It merged with Barrick Gold. The Hearst family, which guided the early destiny of both, has long since gone beyond its mining heritage and into the national and even international spotlight. The mine and the company passed from the scene with as little fanfare as heralded their birth, amid the Black Hills gold rush of the 1870s. They both grew into American mining legends, as did the town they sired and nurtured, Lead. In a real sense, the mine and the company symbolized one of the last links to a vanished world and a mining era.

Jan 1, 2003

By Richard F. Flanagan, Robert H. Marshall

The Republic of Singapore’s Public Utilities Board is implementing the Deep Tunnel Sewerage System Project. The project’s deep tunnel component, 48 km of deep, large diameter sewer tunnels has been successfully completed (the works are in the defects liability period). Six International Design/Build tunnel contracts utilized eight Earth Pressure Balance TBMs ranging up to 7.23 m in diameter to deal with varied ground types ranging from deep soft clays to fresh granite. Numerous access/workshafts were constructed and using various support systems. This paper provides an assessment/overview of the tunnel contracts, tunnel excavation methods and equipment, and the shaft systems. Suggested enhancements to similar future projects are provided.

Jan 1, 2007

By Hyung-woo Kim, Kiyoung Sung, Sup Hong, Jung-Yeul Jung

Many concepts for the commercial production of deep-seabed manganese nodules have been studied since the 1970s. However, the bearing capacity of the deep seabed is not strong because it is composed of fine particles with high moisture content. So it is impossible to carry manganese nodules in the collection system. Therefore, the validity of continuous mining by riser pipe from the seabed to the vessel is highly appreciated. A continuous mining system is composed of mining vessel, lifting pipe, buffer system, transport tube (flexible pipe), and self-propelled mining robot. A conceptual diagram of this system is shown in Fig. 1(a). Korea Research Institute of Ships and Ocean Engineering (KRISO) developed a deep-seabed self-propelled mining robot called "MineRo" to collect manganese nodules in 2012 (as shown in Fig. 1(b)). In 2013, real sea experiments at around 1380 m depth were carried out to evaluate the collecting and driving performance of MineRo. However, we found that the roller in MineRo did not work well at times. To elucidate the problem, we analyzed the rheological characteristics between the bushing and drive shaft under deep-water conditions.

Sep 1, 2014

By R. Q. Honaker, D. P. Patil, A. Sirkeci

Due to increased production of fine coal during mining during this century and inefficient fine coal recovery technologies, a vast reserve of high quality coal currently exists in refuse ponds. A novel fine coal circuit consisting of a hindered-bed classifier, an enhanced gravity concentrator and a flotation column has been evaluated for the recovery of fine coal from refuse ponds. The treatment of a pond derived from Pittsburgh No. 8 seam coal resulted in the production of a premium fuel containing less than 5% ash and a calorific value of about 30,173kJ/kg with 60% mass yield. The results from the treatment of two refuse pond materials will be presented in this publication.

Jan 1, 2000

By Tim Brick, Peter Jewell, Stephen Thompson, Simon Morgan

The $980m (€750m) Dublin Port Tunnel, Europe’s biggest urban highway tunnel project, was opened in December 2006. The culmination of this immense scheme is set to transform the environment, mobility and road safety of Ireland’s capital city. This paper summarizes the key aspects of a project linking both sequential and parallel construction of individual tunnels and describes various approaches to bored, mined and pre-support cut-and-cover tunneling in a wide variety of ground types and depth of cover. Examples of innovative approaches to deal with structural and geotechnical problems while maintaining full operation of both road and rail traffic and the integrity of properties in a dense urban corridor are described.

Jan 1, 2007

By Roger L. King

Working in gassy ground conditions is an everyday occurrence for the U.S. coal mining industry. As tunneling operators begin to venture into projects that expose them to the additional hazard of potentially explosive atmospheres, lessons learned by the mining industry over years of experience should be transferred into this industry. This paper will present practices developed by the U.S. coal mining industry for dealing with the problem of excavating material in potentially explosive atmospheres. Procedures will be discussed that can be used to detect and quantify gas prior to mining that have application to the construction industry. Degasification or drainage practices, including predrainage from vertical and horizontal boreholes, will be discussed. Also, ventilation practices commonly used in the mining industry will be presented.

Jan 1, 1985

By Raymond P. Miller, David L. Monson, Robert A. Robinson

A geotechnical instrumentation program consisting of borehole extensometers and portable tape extensometer stations was effectively used to monitor concrete liner deformations and guide construction procedures during enlargement of a 75-year old Union Pacific Railroad tunnel in Wyoming. Enlargement involved excavation of the old concrete invert and placement of 5,941 feet of new concrete invert 6 feet lower in squeezing shales, fault zones and water-bearing sandstones. Instrumentation data were used to guide procedures for excavating the old invert, installation of temporary interior struts, underpinning existing liner walls, and placing the new concrete invert.

Jan 1, 1976

By J. D. Miller

Characterization of feed material with respect to expected concentrate grade and recovery is fundamental to the design of improved separation efficiencies and to achieve sustainable development in the utilization of our mineral resources. An important reference point for this characterization is the liberation-limited grade/recovery curve which represents the perfect separation, the best separation which can be achieved for a given feed material limited only by the extent of liberation. Now, liberation-limited grade/recovery curves can be determined based on 3D mineral liberation analysis of feed material. Thus, actual separation efficiencies can be compared to what might be expected for a perfect separation limited only by the extent of liberation. It is shown that 3D mineral liberation analysis based on X-ray micro CT (XMCT) is preferred to 2D section analysis which overestimates the extent of liberation. By way of example, procedures and experimental results are presented and discussed for feed material in the case of phosphate rock flotation.

Jan 1, 2009

By J. Egan

The recovery of gold by ore leaching is influenced by the size of the particles and the chemical environment. Within the experimental error associated to the testing of gold ore, results of a series of leaching tests conducted with natural ores rather than monosized samples confirm that gold dissolution increases with decreasing ore particle size. The tests also indicate that the dissolution of gold in the ore within a size interval is weakly affected by the intensity of the size reduction method.

Feb 27, 2013

By David Caiden, Geoffrey Fosbrook, Jaidev Sankar, Donald Phillips, Jon Hurt, Anil Parikh

This paper will cover the progress being made on Phase 1 of New York’s Second Avenue Subway line. It will include a description of construction progress on the first contract to be let, which consists of a 248 m (815 ft) long launch box, 3.9 km(2.4 miles) of TBM tunnels and a tunnel sump; the packaging strategy for the remaining work; and the progress through Final Design of the remaining packages, including the two large span rock cavern stations.

Jan 1, 2007

By B. Mishra, A. Staley, D. Kirkpatrick

The major waste product of the alkaline extraction of alumina from bauxite [Bayer Process] is known as red-mud. Approximately, a ton of red-mud is produced for every two tons of bauxite mined. The red-mud produced from Jamaican bauxite is rich in hematite, alumina and titanium oxide. It has been shown that over 90-wt. pct. alumina can be recovered from red-mud by soda-ash sintering and caustic leaching. Hematite can be carbothermically reduced with a degree of metallization of over 94 pct resulting in attempts for magnetic separation. These separations are desirable in the notion that there is no waste product generated from this type of processing and consequently an opportunity for complete utilization of the waste material. Conversely, the pre-separated material could be charged through the tuyeres in an iron blast furnace or smelted to produce pig iron. If smelted, the concentration of titanium oxide in the slag will be significantly high justifying its recovery by established acid-leach process. This paper describes the results of alumina recovery and the plans for titanium oxide recovery from red-mud. In addition, the situation of ongoing efforts in iron extraction, particularly, the method of magnetic separation of the reduced material. The problems associated with the use of reduced red-mud as an alternative to direct-reduced iron [DRI] has also been discussed. Critical assessment of the recovery sequence chosen for the products has been described based on economics.

Jan 1, 2001

By Steven Norris, William Moler, Michael Cole, Patrick Doig, Debi Lewis, Craig Pyle, Matthew Crow

The recently completed Lower Northwest Interceptor Program (LNWI) in Sacramento, California comprises, ten pairs of micro tunnels totaling 4,369 m (14,417 ft),three horizontal directionally drilled bores totaling 956 m (3,154 ft), and two large diameter tunnels under the Sacramento River totaling 1,198 m (3,953 ft). This paper briefly summarizes surface and subsurface conditions, and planning and design considerations. It then goes on to describe problems encounterd with each trenchless crossing, as well as lessons learned with respect to shaft construction, ground control at shafts during tunnel break-in and break-out, frac-out and heave, settlement, obstructions, coordination with permitting agencies, and application of geotechnical baseline reports.

Jan 1, 2007

By Zephaniah Varley, Dominic Parmantier, Paul Schmall, Richard Martin, Red Robinson

Sequential excavation of the Beacon Hill Station has been accomplished in highly complex and inter-layered sand, silt, and clay soils with multiple perched groundwater tables. Successful excavation has required the installation of a deep dewatering well system used to depressurize sand layers above and within the excavated tunnel faces. In addition, the presence of sand layers in the crown of the Platform Tunnels required jet grouting at depths of up to 49m (160-ft). This paper discusses the design intent, construction, and effectiveness of the dewatering system and the selective jet grouting of sand horizons and shaft break outs for the successful construction of the deepest SEM station excavation ever completed in the United States.

Jan 1, 2007

By L. Bergkvist

"History can provide many answers with regard to what today’s mining industry looks like and how we got to where we are today. It has always been self-evident that safety has to be given the highest priority and, throughout history, many mine workers have been injured, become ill and have even sacrificed their lives due to the way in which attempts have been made to extract the ore, often due to ignorance of the dangers being faced. In more recent stages of history we have seen certain dangers being compensated by means of higher wages and bonus systems in order to have the work carried out: one example of this is when the rock heating method was employed and the men who first went underground to put out the fires that were burning, were paid extra. The working conditions, to which these people were exposed, with smoke-filled closed spaces, shortened their life expectancy considerably and today we can ask ourselves whether it is really possible to value these efforts just by higher wages. In all mines worldwide the working environment has been improved and many mining companies have a zero vision where work-related injuries and accidents are concerned. Despite this, incidents of varying severity still occur and a continuous improvement process and ongoing training is necessary in order to constantly minimise risks and improve the working environment. Atlas Copco takes this into account in all its development and we not only review our own production units but also the needs of our customers, with regard to the machinery that is produced in order to cater for customers’ safety and production objectives. Underground mining probably started at the beginning of the 11th century when people with modest tools tried to extract ores that were present in the bedrock. Methodology has developed enormously over the years with a strong focus on increased efficiency and higher production. In different parts of the world the development is driven forwards at different rates depending on which controlling factors are regarded as necessary. Political decisions, profit goals and productivity have partly controlled the development, but the greatest factor where improvement is concerned still remains with increased understanding of the totality. During more than 1000 years since underground mining has been conducted, all individuals at all levels have constantly improved their expertise and the human element has been of great importance with regard to the development that has been made, even though technology often occupies a leading role when we describe the improvements made."

Jan 1, 2011

By A. Anani

The need to optimize surface mining operations has led to the use of discrete event simulation (DES) modeling of truck-shovel systems. Often, these models assume truck cycle times are independent and identically distributed (iid) random variables, although, with significant bunching on the haul routes, this may not be valid. The objective of this paper is to present a methodology to (i) account for truck bunching due to slow trucks; and (ii) test for cycle time dependence (i.e. whether truck cycle time data is iid or not). We built a DES model that accounts for bunching due to a slow truck(s) and used the cycle times as data for further analysis. We then tested for cycle time dependence using Pearson correlation coefficients. The results show significant correlation of truck cycle times for different number slow trucks, with variable speeds. Assuming iid in modeling results in over-estimation of productivity and the uncertainty surrounding it. The over-estimation of uncertainty is pronounced when the relative difference in truck speed increases. The confidence interval of the means of truck loads/shift decreases with increasing number of slow operators. This work extends the usefulness of DES in truck-shovel applications.

Feb 27, 2013