Search Documents

By J. R. Percival, L. Ip, M. D. Piggott, S. J. Neethling

Component wear due to particle-laden flow is a significant challenge in the minerals processing industry in the handling and transportation of abrasive mineral slurries. Studying wear through experimentation is time-consuming and expensive; therefore possessing the ability to accurately simulate, understand and predict wear in these complex environments is highly desirable. The ability to predict wear is important in both the design of equipment in order to maximise the performance over the wear life of the components, as well in minimising potentially costly and dangerous failures and unscheduled maintenance.. Particle-induced wear is a complex problem, requring an understanding of coupled fluid-solid motion, geometry deformation in response to fluid-solid behaviour, moving geometries and wear modelling. Although the literature demonstrates that rebounding particles and changes to surface profiles can have a significant effect on subsequent wear rates and patterns, the challenge of implementing a model to account for this effect in complex geometries has been addressed by only a few authors in the literature. This paper describes a new wear simulator, leveraging fluidity, an open-source, massively parallel, finite element based CFD simulator capable of unstructured adaptive meshing. The wear simulator includes the ability to model particle-laden flow using representative Lagrangian particles and dynamic remeshing of geometry in response to wear and component movement. These capabilities are demonstrated using wear and the associated dynamically deforming boundaries within a Coriolis tester arm, with the results comparing favourably with the experimentally observed wear patterns. Keywords: CFD, wear, two-phase flows, anisotropic mesh adaptivity, boundary deformation

Jan 1, 2020

By H. Edinger

China?s engagement with the African continent has increased impressively in the past decade. Even though China is not the African continent?s largest stakeholder, the rapidly increasing engagement is evident in the huge number of Chinese migrants that have come to Africa in the wake of unprecedented trade and investment levels, as well as in increasing diplomatic and political interactions, which has taken most other commercial partners by surprise. All but four countries in Africa have adopted the ?One China?1 policy stance; and in so doing opened the door for new or strengthened commercial dealings with China, including increasing investments into Africa?s extractive industries. This has been particularly evident since the turn of the century, with a clear shift in China?s policy towards Africa elevating the continent in China?s foreign policy objectives. As such, Africa has become a strategic focus2 for Chinese outward bound and internationalizing companies, especially in the extractive industries. This planned shift in focus is based largely on geo-strategic and commercial needs and interests, rather than previous ideological ones.3

Jan 1, 2011

By D. G. Krige

D. G. Krige: The stimulating contributions from Messrs Cooke, Curtis, Martus, Johnston, Van Wyk, Van Rensburg and Wroth are appreciated by the author and provide clear evidence of the importance not only of the principle of assistance to gold mines, but also of its scope and form. In general all the arguments, raised by Messrs Cooke, Martus and Johnston in favour of extending the scope of the new assistance scheme can be accepted as sound.

By A. Sampson-Forsythe, P. Morissette, A. R. Punkkinen, D. R. Chinnasane

"The performance of ground support systems under dynamic loading is typically assessed in a qualitative and subjective manner. As a result, it is difficult to develop an explicit knowledge on the mechanisms of action and interaction of support elements subjected to rockbursts. This paper examines rockbursts that have occurred at Creighton, Copper Cliff, and Coleman mines since 2000, 2004, and 2006, respectively. The mines are located in the Sudbury Basin, in Ontario, Canada. The majority of pertinent information was obtained through on-site field assessments, seismic system records, and numerical elastic stress modelling. Passive monitoring is used to link the evolution of the frequency and severity of rockbursts to the evolution of mining and support practice at the three mine sites. Based on the collected data, ground support elements that enhanced the capacity of support systems to withstand dynamic loads are identified. IntroductionThe selection of appropriate mining methods, extraction sequences, rock mass de-stressing techniques, and ground support systems is of great importance in mitigating the level of rockburst-related risk. In burst-prone conditions, the design of support systems should account for the anticipated dynamic load demand and the capacity of the available support options. Furthermore, an economical design should, implicitly or explicitly, take into consideration the consequences of a rockburst and its impact on worker safety and mine productivity. Stacey (2012) has argued that we have a limited understanding of the mechanisms of rock mass behaviour in seismic conditions. This is compounded by a ‘lack of understanding of the mechanisms of action and interaction of support elements under dynamic loads’ (Stacey, 2012). Consequently, the design of support systems required to manage dynamic loads is usually based on experience. The assessment of the dynamic performance of ground support systems is typically subjected to qualitative (and sometimes subjective) interpretations from ground control personnel."

Jan 1, 2017

By A. Hoogervorst

Cyanide is a key contributor to the efficiency of gold extraction. Public perceptions of cyanide are emotive and following some publicised incidents involving cyanide, the gold mining industry established a voluntary cyanide code for the manufacture, transport and use of cyanide in the production of gold. The paper describes the development of the code, its content and the third party auditing of the code as a means of establishing and maintaining benchmark standards. In adhering to the cyanide code requirements, there are overlaps with other management systems such as ISO 14001 and OHASA 18001 and the paper seeks to show how existing mine systems can readily accommodate cyanide code compliance and that operating and auditing the cyanide code can assist in the integration of mine heath, safety and environmental management systems.

Jan 1, 2009

By S. A. Hosseini, O. Asghari

"Recoverable mineral resources assessment has become a standard geostatistical application in the mining industry, with various geostatistical techniques currently available. This investigation aimed to improve the prediction at the Sungun deposit and to obtain mineral resource models capable of handling (i) the change of support from drill-hole composites to selective mining units (SMUs), (ii) the multivariate nature of the ore control selection criteria that involves both copper and molybdenum grades; and (iii) the local uncertainty on the true (unknown) grades. The solution presented in this paper is to use direct block-support sequential cosimulation in order to construct a set of alternative outcomes of the copper and molybdenum grades on block support over the deposit, with no need for storing point-support values, hence with a considerable gain in memory management and CPU time. The grade realizations so obtained are then processed to calculate the uncertainty in the mineral resources that can be recovered above given cut-off grades, both globally and on a blockby- block basis. IntroductionGeostatistical methods are widely used by mining companies to determine a resource model of the tonnage and head grade of a potential orebody, which is one of the first and most critical inputs underpinning any mining project. The prediction of the grade, tonnage, and recoverable metal for a particular mining plan and the corresponding financial forecast constitute the main technical risks in mineral resource evaluation. The conventional approach to this problem is to predict the mineral grade for constant volumes relevant to the mining plan and to base the recoverable mineral resource calculations on those predictions. Alternatively, one can directly predict the local variability in the mining block grades based on a spatial distribution model (David 1988; Rossi and Deutsch 2014). Multiple realizations can also be constructed by conditional simulation, providing a more complete representation of block grade uncertainty, as well as the uncertainty over multiple blocks. Simulation methods allow quantification of the uncertainty of the mineral resource prediction risks in downstream studies such as mine design, mine planning, or operational optimization studies; the risk assessment is achieved after applying transfer functions to the conditional simulation models (Dimitrakopoulos 2012; Rossi and Deutsch 2014)."

Jan 1, 2017

By L. E. Salinas-Farran, S. J. Neethling

Key variables in heap leaching include permeability, mechanical stability and mass transport. All of these properties can be manipulated by agglomerating and curing the ore before stacking it into heaps. The chemical and structural evolution of the agglomerates during curing is key to improving agglomerate properties and, ultimately, heap performance. It is possible to image the internal structure of agglomerates using SEM/EDX (e.g. QEMSCAN or MLA), although these methods are destructive and do not represent the 3D structure of the agglomerates. A non-destructive alternative is to image the agglomerates using X-ray Microtomography (XMT). Not only does this provide 3D information, it also allows the same samples to be repeatedly scanned, allowing the time evolution of the agglomerate structure and chemical composition to be tracked. In this paper we compared the behaviour of ores agglomerated using a combination of sulphuric acid and ferric sulphate with ones in which chloride ions are added to the recipe, since chloride leaching is gaining in popularity as a chemical alternative to bioleaching for sulphide ores. We tracked the curing process beyond the typical time scales to see the impact that this has on both the agglomerate structure and the subsequent leaching behaviour. Keywords: Heap leaching, curing extent impact, leaching kinetics, ferric-chloride leaching

Jan 1, 2020

By B. Yu, M-H. Cao, C. Zhou, X-Z. Zhang

The transient infiltration and lubrication behaviour of slag during continuous casting of steel is important for billet quality. A two-dimensional coupled mathematical mould model was developed to investigate these phenomena. The accuracy of the model was verified by comparing the calculated slag consumption with measurements by the plant. The results show that the liquid slag is consumed from the middle and late period of positive strip time to the next early period of positive strip time, including the entire negative strip time. The maximum downward infiltration velocity and positive pressure in the slag channel is at the middle of the negative strip time. Increasing the positive pressure of the slag channel is conducive to lubrication. The shear stresses acting on the shell surface and at the mould side were determined by the lubrication slag consumption and total slag consumption, respectively, and gradually decreased with increasing slag consumption. The negative strip time was lengthened to increase the slag consumption and prolong the time near the maximum downward shear stress, so as to be conducive to the demould.

Apr 16, 2024

By J Cahill, M Lee

Leinster Nickel Operations, located in Western Australia, consists of an underground and three open pit mines in relatively adverse ground conditions. This paper reviews our ground control practices in the open pits, covering aspects of ground support, wall control and monitoring. These methods have been effective in allowing mining operations to continue beneath unstable slopes. In particular, the use of Groundprobe?s Slope Stability Radar has enabled the Harmony Open Pit to safely operate for months following indication of failure from traditional methods. This case study highlights the benefits of investing in appropriate slope stability monitoring systems.

Jan 1, 2006

By Kym L. Morton

Ground water and associated pore pressure represent elements which can have a negative impact on surface mining and slope stability. Ground water flow and deformation within a slope influence each other. An increase in pore pressure will result in a decrease of effective stress; and conversely if the pore pressure decreases, the effective stress increases. Slope analysis and slope design calculations require good information on pore pressure distribution around an open pit excavation. Until recently very little pore pressure data was available and assumptions had to be used. Location and design of measuring points depend on geological and structural setting, geotechnical domains and practicality. Good planning and the use of sensitive point piezometers to measure in situ pore pressures means that real-time data can be collected and used for the construction of flow nets, the determination of pore pressure distribution around an open pit mine, the validation of the dewatering/depressurization requirements, the calculation of the efficiency of the dewatering system and finally the use of pore pressure data in slope stability analysis. The recommended layout for a monitoring system, types and design of piezometers, data collection and use of the pore pressure data are presented.

Jan 1, 2008

By M. Rudolph, J. Sygusch

Froth flotation is well-established and efficient in the selective separation of valuable particles from unwanted material with sizes ranging from 10 μm to 200 μm. However, when it comes to the separation of ultrafine particles (< 10 μm) there are still some challenges, or rather opportunities. This research aims at developing a method for the separation of ultrafine particles based on multiple particle properties. Amongst such properties are wettability, morphology (shape or roughness) and size with applications not only in mineral processing but in general chemical engineering. In this study, three differently shaped fractions are used as valuables for testing: spherical particles, elongated particles and irregularly shaped particle fragments; together with ultrafine magnetite as the gangue material, in order to investigate the effect of particle morphology on ultrafine particle flotation, as well as wettability, which is varied by esterification using alcohols. Flotation tests are carried out using a novel flotation device that was designed especially for the flotation of ultrafine particles, combining advantages from machine-type froth flotation and column flotation. The results showed that, in contrast to previous studies, recoveries for ultrafine spheres were higher than for ultrafine fragments for all wettability conditions, and hydrophobisation generally increased particle recoveries for said morphologies. Tests using fibres showed different behaviour as hydrophobisation had negative effects on their recovery, despite increased selectivities and kinetics. These findings suggest that apart from influences of particle properties within the suspension zone, their effects on the froth characteristics should be studied in more depth. Keywords: Ultrafine particles, Flotation, Particle shape, Wettability, Esterification of glass, Hydrophobisation

Jan 1, 2020

"Sampling error and bias, especially the Increment Preparation Error (IPE), are introduced when the tool allocated to do the job fails to extract a representative sample. This is the case with chip sampling; the tool can only extract haphazard shapes of loose or fractured material and not always from within the demarcated sample area. Increment Extraction Error (IEE) and Increment Delimitation Error (IDE) could be severe, but are found to be relatively unbiased. The uncontrolled action of the sampler in discarding excess sample material after sample collection has a significant impact on the error and bias introduced with each and every extraction. A new type of bias, referred to as the ‘waste discard bias’, arises when samplers select what portion of the excess sample material to discard at the sample site. Material visually identified as waste is discarded in preference to mineralized broken ore if there is an excess of sample material. This results in a considerable error in the analytical results. The bias is proportional to the reef-waste ratio in the demarcated sample. IntroductionTwo types of ‘sampling’ are distinguished, namely sampling of particulate materials (broken ores) and sampling of solid, unbroken in situ mineralized reef. This study considers only chip- or face-sampling of in situ, goldbearing, carbon-rich conglomerates typical of the Upper Witwatersrand Supergroup and examines where components of sampling error and bias, clearly specified in the Theory of Sampling, may arise during the practice of ‘face sampling’. Many millions of face samples have been extracted from Witwatersrand-type mines using a hammer and chisel, and detailed descriptions (standard operating procedures) of how the samples should be taken have been developed by many mining companies. There is, however, no taxonomy or nomenclature for managing or reporting the different types of errors associated with chip sampling. The Theory of Sampling compiled by Pierre Gy in the early 1950s provides, comprehensive nomenclature of sampling errors that is applied to particulate sampling of ore in a lot, a stockpile, or a moving stream on a conveyor belt. The taxonomy and characteristics of sampling errors, grouped according to the sources from which they arise, and identified by Gy (1973, 1979, 1982, 1992, 1995, and 1998) are shown in Figure 1. This classification of errors is used extensively in regard to the sampling of particulate materials in the mining and minerals industry, but not in regard to chip sampling. A relatively small mass (hundreds of grams) of representative particulate material for estimating the average grade of a much larger mass (thousands of tons – the ‘lot’ in the Theory of Sampling) is extracted by the chipping or cutting of a representative rock ‘sample’ from the stope face."

Jan 1, 2016

By R. G. B. Pickering

The South African narrow reef hard rock mining industry has been stuck in a time warp with relatively little change in the mining process in the last century. This paper presents a methodology on how to implement change in narrow reef hard rock mining. It then explores a number of technologies that have been introduced into this mining industry and the impact that they have had on the mining process. The author then presents his view on whether the defined change process has been followed and sets out to identify the most critical aspect of ensuring that change is successfully implemented. Future demand will also be speculated on.

Jan 1, 2007

By B. P. Watson

In South Africa, the Bushveld platinum group metal deposits are unique in that they are the largest platinum group metal deposits in the world. These deposits occur as two distinct stratiform tabular orebodies and strike for many hundreds of kilometres. Mining is extensive, with depths ranging from close-to-surface to 2 000 m. The mining method is a variation of planar open stoping. Pillars are widely used to support the open stopes. Crush pillars are commonly used in this role, where the residual pillar strength provides the required support resistance to stabilize the stoping excavations. This paper describes the direct measurement of stress within these crush pillars, and describes the stress?strain behaviour of these pillars. These findings indicate that the measured pillar failure stress is too high. The implications of these findings are that roof damage and pillar bursting could occur, and some examples of this type of damage are shown. The paper concludes that this problem could be mitigated if the three dimensional pillar geometry were modified and the pillars were cut smaller.

Jan 1, 2007

Gold Fields is the world?s fourth largest gold producer with operations in South Africa, Australia, Ghana and South America. All of Gold Fields? South African Operations are located in the Witwatersrand Basin and are intermediate to deep level underground mines exploiting gold bearing, shallow dipping tabular orebodies, which have collectively produced over 50 kt (1,608 Moz) of gold over a period of more than 100 years. Although the use of Monte Carlo as a business tool was introduced in 1964, it has only been in the last 30 years that it has gained increasing acceptance within the mining industry. However, the application thereof has been mostly limited to determination of risk in project areas. This paper however, considers the possibility of using Monte Carlo simulations to asses the underlying ?Root Cause? criteria critical to the operations management of existing mining operations. Currently, working operations have a distinct advantage over project areas as they have a wealth of historical information at hand. This, in turn, can be utilized to model distributions and relationships that can be used in Monte Carlo simulations, the results of which can be analysed to determine areas of concern. Projects can then be set up to ameliorate the effects of these and in turn reduce the risk of not achieving the operational targets. It is here that it must be stated emphatically that it should be the ?root causes? and the associated relationships that need to be emplaced within the model in order to achieve results that reflect the true causal relationship. The paper outlines possible sources of ?root cause? relationships and considers the outcomes of these in a case study on a large South African Gold Mine.

Jan 1, 2009

By R. A. Govender, A. Mudau

"Rockbursts continue to be a major contributor to mine accidents and cause of damage to mine excavations, particularly at great depth. The problem of rockbursts has also escalated in civil engineering tunnels driven at depth, due to high levels of in situ stress at such depths. Attempts have been made in the past to mitigate the impact of rockbursts, with rock support remaining the ultimate method for providing stability in rockbursting environments. However, records show that, on many occasions, conventional support elements such as rockbolts, wire mesh, shotcrete, and lacing fail to withstand severe rockburst events.Recently, a support method termed ‘sacrificial’ support was proposed as a potential additional method to prevent rockburst damage, based on observations made after rockburst events in a mine. The philosophy behind a sacrificial support system is that, under dynamic loading conditions, support in the form of a liner must fail; leaving behind, undamaged, what was previously supported rock mass. The sacrificial support concept reported herein is applicable in situations where the source (i.e. seismic event) of the rockburst is located remote from where rockburst damage is likely to occur.Spalling tests based on the split Hopkinson pressure bar (SHPB) technique were conducted to study some aspects of dynamic rock fracturing in tension at high strain rates and the role a sacrificial layer plays in combating dynamic rock failure. A single Hopkinson pressure bar, with a long cylindrical intact rock specimen attached at the bar free end, was impacted by a striker on the opposite free end in order to generate a dynamic stress pulse responsible for spall failure upon reflection from the specimen free end. Different liners and liner combinations were then introduced at the specimen free end as support. Such a simple, yet robust, experimental set-up allowed the potential benefits and failure mechanisms associated with sacrificial support under dynamic loading to be demonstrated and compared with ‘sacrificial support’ behaviour observed in real rockburst events in a mine. Analysis of the results revealed that varying liner thickness and mechanical impedance between rock and support liner play a significant role in limiting rockburst damage."

Jan 1, 2016

By C. van Buuren, R. F. Sandenbergh, P. J. Pieterse

Gold extraction from double refractory ores using conventional cyanidation has proved challenging due to the presence of carbon within the ore. Carbon particles may adsorb leached gold resulting in gold losses to tailings, i.e. preg-robbing the gold. Some of the preg-robbed gold may be recovered by the application of the HiTeCC process on CIL tailings. The process developed by Metso Outotec involves caustic conditioning of the tailings followed by high temperature desorption and simultaneous adsorption onto virgin activated carbon of the aurodicyanide. The aim of this paper was to develop a model for the HiTeCC process which could be used to support design and optimisation of the process, based on the adsorption characteristics of the preg-robbing and activated carbons. It was found that accurate experimental isotherms can be used to predict the behaviour of preg-robbing adsorbents. Comparing the sorption isotherms for preg-robbing ores and activated carbon indicated similar dependencies on temperature and ionic composition. Applying boundary layer diffusion models coupled with experimentally determined isotherms for preg-robbing ore and activated carbon, the HiTeCC process was successfully simulated at experimental and plant scale. Gold recovery of the HiTeCC process is most sensitive to the temperature of desorption and gold loading of the activated carbon, with increased temperature improving recovery. The gold loading of the activated carbon in the process should always be maintained lower than that of the normalised pregrobbing carbon gold loading to ensure favourable conditions for adsorption onto the activated carbon. Caustic conditioning stabilises adsorption and is therefore not necessary during the desorption stages of the process, but potentially improves recovery during adsorption. Keywords: Preg-robbing, refractory gold ores, HiTeCC, aurodicyanide

Jan 1, 2020

Dr Hanekom I would like to thank Dr Hanekom for a very valuable -contribution; it summarizes careful statistical test work which was an omission from the original paper. Minor manipulative details, the application of a finer measuring graticule and the reproducibility of the procedure are described and the author accepts with gratitude this ready-made answer to the first and second points of Dr Finkelstein&apos;s comments. Mr Williamson The author is indebted to Mr Williamson for historical background to early experiments with captive bubbles and it is conceded that the original paper described another avenue to an old flotation goal. The field of application is restricted and we would not work with all the material illustrated by Klassen and Mokrousov.1 The particles in Figure 74(a) are far too large and irregular; material in Figures (b) through (d) could be employed for semi-quantitative work in spite of obvious disadvantages; Figure 74(f) represents ideal conditions. We have studied this mineral-collector association in the size range given and results were satisfactory. For larger pick-up values than that illustrated an induction period of more than 0.01 second was required (actually 90 seconds for a maximum bubble load at pH 7.2 with 25 g/t oleic acid!). REFERENCE 1. KLASSEN,V. I. ANDMOKROUSOV,V. A., &apos;An Introduction to the Theory of Flotation,&apos; Butterworths, London, 128, Figure 74, (1963). Mr Slander and Mr Kooij Researchworkers in a practical mineral development laboratory may well ask what contribution yet another micro-technique can make to the problems of large scale ore flotation. The obvious answer is that there can be little or no direct translation of results obtained with a static system comprising air bubble and pure mineral concentrate to a dynamic multicomponent operation. However, for the rapid study of one mineral or variable some small scale apparatus must be employed. In the Anglo American Research Laboratory, the described semi-quantitative pick-up technique has filled a niche and requirement. For ourselves, the system represents a definite advance over the contact angle approach in that samples of minerals conventionally prepared in laboratory or plant may be used, which is a desired step nearer flotation. We bracket this pick-up apparatus with the Hallimond tube1,2 and evidence is now to hand that pick-up curves may often be related to flotation recoveries obtained from this tube with pure mineral samples and from the Fuerstenau glass cell3 with the total ore at low pulp densities. We would not wish to push the comparison of pick-up results past this stage for there is much published development work relating the Hallimond and Fuerstenau equipment to flotation on a larger scale. At the Anglo American Research Laboratory for example, a test in a Fuerstenau cell is often the final integrated step in laboratory investigations into the TORCO process. As these contributors rightly point out, pick-up tests can offer nothing towards the determination of optimum reagent dosage for large scale flotation. This is the function of bench-type flotation cells with up to 2 kg batches of ore. At this level, collector performance and consumption and physical properties of the froth are more comparable with large scale operation. The pick-up cell, Hallimond tube and Fuerstenau cell are essentially equipment from which the effect of control parameters can be derived. For the assessment of collector behaviour, the pick-up approach is rapid and economic and we offer here a pick-up contribution towards the flotation of Witwatersrand uraninite with anionic sulphonate collectors (Fig. 1). A large crystal of the local mineral was not available for contact angle measurements and owing to its low concentration in Witwatersrand gold-bearing reef, a small sample was laboriously obtained by tabling, superpanning and heavy medium separation. The pick-up values of a sized portion were determined by the described procedure in the presence of nine petroleum sulphonate collectors. Responses fell into two categories; "normal" curves (dotted lines) and a group of collectors which were very active at low concentration but showed depression of pick-up at the higher levels. The similarity in form of curves for collectors 1 and 3 was apparent and reagent 3 was found to be simply a diluent of 1. Otherwise, collector performance could not be related to either sulphonate content or molecular weight of the active constituent. However, reagent 2 gave the best performance in a bench flotation cell with regard to overall uranium distribution but, as predicted, reagent 1 yielded the best grades. Later pick-up tests with a similar class of collector have suggested that depression at high reagent concentrations may be due to "bubble armouring" whereby an hydrophilic air-liquid interface is produced which rejects mineral attachment. Prolonged investigations with the same mineral sample have not been required except for the study of uraninite which lasted for more than a year. Variation in pick-up response could not be detected over this period during which the mineral was stored under distilled water. The only visible change was a small efflorescence of lead sulphate, readily removed and decanted off after stirring with a glass rod in the sample tube. In its main role as a "trouble-shooter", the pick-up method is applied to fresh mineral samples taken from a flotation plant and soon discarded or from a current run in the ore-dressing laboratory. After production of a concentrate, a solvent cycle, as described in the original paper, may be required to remove heavy organics or other contaminants as when a sample has been taken from circuits containing detergents, grease or return flotation solutions. This solvent cycle will not remove chemisorbed collectors and we prefer not to work with minerals from flotation tailings or with pick-up cell discards. It has been thought preferable to answer the contributors&apos; other apprehensions with regard to sample preparation, activators, depressants and the physical properties of reagents in another paper on offer to this Journal. It covers pick-up investigations relating to the flotation of nickeliferous pyrrhotite at two Anglo American Corporation Mines, which approach seemed the correct orientation for a reply to another contributor to this paper.

Hydrometallurgical processing of complex ores and concentrates is becoming increasingly important as the mining and metallurgical industry seeks to exploit mineral deposits that are difficult to treat using conventional mineral processing and pyrometallurgical technologies. Mineral processing is often challenged by the difficulty or inability to separate valuable minerals into marketable concentrates. Hydrometallurgical processing, using selective leaching technology, can often ?chemically beneficiate? such difficult deposits. Pyrometallurgical treatment of base metal concentrates is capital intensive and subject to ever more stringent environmental control. Hydrometallurgical processing is generally lower in capital cost for an equivalent metal production rate and avoids the gas and dust issues associated with pyrometallurgical processing. The possibility of by-product recovery may also increase with hydrometallurgical treatment. Two examples of new technology or flowsheet development for treatment of complex ores and concentrates are used as illustration. These include the El Boleo process of Baja Mining for recovery of copper, cobalt, zinc and manganese from a complex clayey ore and the PLATSOL? process for recovery of copper, nickel, cobalt, platinum, palladium and gold from a bulk sulphide concentrate.

Jan 1, 2009

As part of a broad program to optimise the performance of their grinding circuit, BHP Billiton Cannington have installed an OCS© Expert system together with three VisioRockTM online particle size analysis cameras. The main purpose of the system is to stabilise grind size and feed to the flotation circuit. This particular application of OCS© is the first installation to incorporate Metso Minerals Process Technology-Asia Pacific&apos;s (MMPT AP) Dynamic SAG/AG Mill Model, which is able to predict numerous mill parameters that were previously unable to be measured with the existing plant instrumentation. Integrated into the logic of the control algorithm are online vision based, particle size measurements of the AG mill feed and recycle crusher product. This paper will describe the history of the project from initiation to date, the model and OCS© logic configuration, and demonstrate the significant benefits realised at Cannington mine.

Jan 1, 2007