Search Documents

By Robert L. Frantz

The performances of the three bituminous coal demonstration methane re¬covery boreholes, located in Greene County, Pennsylvania, are reviewed. Development of these vertical holes was largely underwritten by project funds. Reference is also made to an anthracite coal methane project in Luzerne County, Pennsylvania. This involved one vertical hole and was underwritten by a utility company. In addition, an exploratory drilling in the southern anthracite, which provided the project group with coal cores for methane gas analysis, is also cited. The technical and economical data that were gathered from the various methane projects are analyzed. Finally, the advantages and disadvantages of methane recovery by vertical boreholes are assessed.

Jan 1, 1978

By D. R. Corson

The Bureau of Mines instrumented an operating stope in a deep vein mine to determine the amount of wall closure and the magnitude of loads imposed on a backfilled stope. Hydraulic pressure cells used to monitor pressures in the fill) with bolt closure points to measure vein-wall movement and the procedure for their installation) are described) and the results of the laboratory calibration analysis of the reliability of these cells are given. An attempt to monitor density and moisture changes in the backfill with a nuclear density-moisture device was only partly successful) owing to either deformation of access tubing or relative displacements of the vertical vein walls relative to the emplaced tubes. Data from the instrumentation indicate vein-wall closure in excess of 20 inches and pressures within the fill approaching 600 psi. Analysis) incorporating field data with results of laboratory tests of the compressibility of timber and tests defining the constrained moduli of the fill) points out the limited restraint to vein closure offered by timber sets. Ground movement induced by mining activity could be more effectively con-trolled by the use of densely compacted backfill.

Jan 1, 1967

By William R. Barton

Anthracite has been mined from the Narragansett Basin of Rode Island and Massachusetts sporadically, and with limited success, for more than 170 years. Beginning in 1974, interest in the coal of the Basin was renewed because of increasing prices and supply uncertainties involving petroleum products. During 1974-77 the Bureau of Mines analyzed 28 samples of Basin coals and conducted washing tests on 20 of them. Results, reported herein, indicate that the coals are low-sulfur, moderate- to high-ash anthracites and semianthracites, suitable for physical preparation to a product generally containing less than 10 percent ash. Additional exploration, sampling and testing will be required to permit appraisal of the potential value of the Narragansett Basin coal resources.

Jan 1, 1977

This report, the third in an annual series, outlines recent trends and developments in the minerals industry. Discussed are new methods, equipment, techniques, and systems used to more, effectively extract and process minerals and fuels. Environmental considerations, reduced ore grades, and the related increased quantities of material handled were the dominent concerns of the minerals industry in 1972. Productivity increased in most mineral commodities as equipment became more mobile, versatile, and sophisticated. Increasingly, equipment designs incorporated health and safety features. There was considerable interest in the field of energy and in pollution-free metallurgy processes.

Jan 1, 1973

By N. Seidle

Numerous studies conducted in the 1960's and 1970's concluded or implied (1) that a high accident rate in terms of severity and frequency exists among new (first year) operators of mine machinery equipment, and (2) that lack of experience and training is a major cause of this high accident rate. Further studies refined this premise to show that the major causes of accidents among first year operators are: (1) lack of manipulative skills; (2) failure to follow/adhere to routine procedures; and (3) failure to recognize and respond properly to hazards. This report describes the design, development, and manufacture of a shuttle car operator training system, including a program of instruction which: ? Is economically feasible. ? Addresses accident data and specific causes of accidents. ? Includes an aerospace quality simulator of sufficient fidelity to teach and develop manipulative skills, recognition of and response to hazards, and routine and emergency procedures. ? Is designed to significantly reduce the severity and frequency of accidents especially during the operator's first year. ? Is designed to significantly improve the performance of the trainee as compared to the standard learning curve. Development of the simulator produced several valuable by-products including a major state-of-the-art technological advance in visual systems for simulators, and a first-time application of (certain) advanced filming techniques to underground filming.

Jan 1, 1984

By Warren E. Morrison

INCREASED production and utilization of minerals fuels and power accompanied the overall expansion in U.S. economic activity during 1963, which saw continued advances toward higher production, employment, and purchasing power. During 1963, record levels of wages, profits, and consumption were attained, while costs and prices maintained the stability exhibited throughout most of the recovery period. Expanding industrial production, the average index of which went from 118.3 in 1962 to 124.3 in 1963, narrowed the gap of unused manufacturing capacity to an estimated 5 percent. Gross national product (GNP), another major indicator of economic activity, reached a record level of $583.9 million (current dollars) during the year, this being $27.7 billion, or 4.9 percent above 1962. These achievements were somewhat marred by unemployment, which remained at 5.5 percent of the labor force in 1963, and the continued deficit in the U.S. balance of payments. Against this general background, total national consumption of energy resources for the year was equivalent to 49,816 trillion British thermal units (Btu), an increase of 4.2 percent over 1962. This represented a somewhat lower rate of growth than for GNP during the year.

Jan 1, 1964

By James M. Spear

Sample results suggest the only mineral resources in the study areas are placer gold deposits along the South Fork Kern River in the Woodpecker RARE II unit (fig. 1). These deposits, in Rockhouse Basin, total 4.5 Figure 1.--NEAR HERE. million cu yds (3.4 million cu m) of indicated subeconomic gold resources in four deposits of "older" gravel. Gold value in samples averages $0.36 per cu yd ($0.47 par cu m) and is as much as $4.44 per cu yd 1/. Cost of mining the gravel and recovering the placer gold is estimated to be more than $2 per cu yd ($2.62 per cu m) for a deposit of this size and type. Additional inferred subeconomic placer gold resources with similar grade probably occur in four other deposits of "older" gravel on which no mining claims were located. Placer gold occurrences on upper Trout Creek contain gold worth as much as $4.50 per cu yd ($5.88 per cu m) 1/. Average grade is much lower, and only about 1,000 cu yds remain (760 cu m). These occurrences do not constitute a resource, but may attract hobbyists not dependent upon making a profit.

Jan 1, 1982

By J. Mitchell Linne

In 1986 at the request of Bureau of Land Management, the U.S. Bureau of Mines studied 23,225 acres of the 27,980-acre Jordan Craters Wilderness Study Area (OR-003-128) in order to evaluate its identified mineral resources. The study area is located in Malheur County, OR, about 20 miles northwest from Jordan Valley. No mining activity has been recorded within the study area, and no metallic or industrial mineral resources were identified. Small isolated occurrences of decorative quality stone were identified. However, none of these occurrences constitute a resource. Although the study area is underlain by relatively young volcanic rocks, the area has no known geothermal energy resource.

Jan 1, 1987

By H. P. Greenwald, Irving Hartman, H. C. Howarth

"INTRODUCTION A report of tests of seven small pillars formed from the Pittsburgh coal bed in the Experimental coal mine was given in Technical Paper 605 5/ Five additional pillars were tested between July 1939 and. October 1940. The data obtained, in the later tests permit an extension of the conclusions reached in Technical Paper 605, which appears to be important enough to the mining industry to justify a progress report that will explain briefly what it is and how it was obtained. Full detail of the tests will appear in a second technical paper, preparation of which is deferred so that results of pillar tests now under way my be included.DESCRIPTION OF TESTSExcept for minor improvements in operating details, the five additional tests were made as described in Technical Paper 605, pages 2 to 7. Briefly, the desired pillar was formed from the coal bed, by excavating a passage around it (no explosives were used), and enough material was removed from above to permit installation of the assembly used for applying pressure. Each pillar was tested resting on its original fireclay floor, which was restrained from lateral flow by a ring of concrete. Vertical and lateral movement of the pillars in two directions as measured carefully in all tests."

Jun 1, 1941

By Wils L. Cooley

The report covers tests and criteria for the establishment of safe grounding systems for coal mines. The work deals primarily with under-ground coal mines, but much is applicable to surface mines as well. Included is an extensive guide to grounding and bonding procedures for mine surface substations. Xit-Rods are evaluated and shown to deviate from manufacturer's claims. An analysis shows that very long cables are difficult to monitor using audio frequency ground-check techniques. A method is developed to detect failing cable splices without removing the cable from service. Simulation and measurement are compared for a technique to detect bad rail bonds, and an assessment is made of grounding techniques for dc face equipment.

Jan 1, 1979

By Charles Sabine

The U.S. Bureau of Mines studied mines and prospects in the Bristol/Granite Mountains Wilderness Study Area (WSA) in 1982. The 45,000 acre WSA, located in the eastern Mojave Desert of California, is underlain by Mesozoic plutonic rocks with scattered roof pendants of Paleozoic (?) metasedimentary rocks. Two mines and six prospects are identified; one mine, the Silver Lode Mine, and a prospect of unknown name are adjacent to the area. The Silver Lode Mine has occurrences of silver, lead and zinc. Within the study area, the Comanche Mine has occurrences of iron and copper and the Iron Victory Prospect has an occurrence of iron. None are large enough to constitute a resource. Occurrences of magnesian marble at the Comanche Mine, Iron Victory Prospect, and elsewhere in the area contain too much MgO for commercial use other than agricultural soil supplements or crushed stone. Transportation costs to markets would exceed the value of the rock. At the Comanche Mine, situated in a roof pendant of marble, about 10 tons remain of a 110-ton pod of magnetite which contained 42.5% iron, and less than 50 tons remain of a mineralized fault breccia which averaged 2.5% copper and 0.3 oz/ton silver. Magnesian marble contained 41 to 45% CaO and 14 to 16% MgO. Primary and secondary silver, lead, zinc, and copper minerals are disseminated along altered joints and in quartz veins in quartz monzonite at the Silver Lode Mine, adjacent to the WSA. Analytical data are sporadic; samples contained as much as 0.12 oz/ton gold, 1.8 oz/ton Silver, 1.1% lead, 3.8% zinc, and 0.3% copper. Mineralized zones in the workings are not resources, but they might indicate possible silver-lead-zinc resources at depth. At the Iron Victory Prospect, lenses of magnetite and hematite with some chalcopyrite occur in a skarn lone in a marble roof pendant. About 110,000 tons of iron-rich rock, averaging 47.2% iron, are present; the largest lens contains about 30,000 tons. About 150,000 tons of magnesian marble, averaging 41.0% CaO and 11.7% MgO, are also present. Deposits of stone, and sand and gravel in the WSA are too distant from markets to be resources. Occurrences of energy minerals were not identified.

Jan 1, 1984

By E. J. (Kirk) Conway

The objectives of this project were to: (1) determine the extent to which maintainability design concepts and principles have been applied to the design of underground coal mining equipment, (2) try to assess its impact on productivity and personnel safety, and (3) develop maintainability guidelines to enhance the design of new or rebuilt equipment. An equipment design review was completed at ten operational coal mines. The purpose was to identify design approaches and features that enhanced and degraded the maintenance process. Mine management, safety, and maintenance personnel were also interviewed to identify machine specific design problems. Six original equipment manufacturers were visited and the procedures used to enhance the maintainability of Their equipment discussed. Volume I of the Final Technical Report presents an overview of procedures and protocol used and a summary of the findings. Volume II includes the maintainability design guide for mobile underground mining equipment.

Jan 1, 1988

By Charles E. Whieldon

The importance of producing more oil from known petroleum reserves has placed increased emphasis on the application of secondary-recovery methods. Recently published reports3 4/ describe the results of waterflooding in Roane and Pleasants Counties, W. Va. (see fig. 1.) This report describes the Barron Kidd Oil Co.?s Santee waterflood project, Maxton sand, Burton field, Church district, Wetzel County, W. Va. (See fig. 2.) The Federal Bureau of Mines hopes that these reports will stimulate interest in improved waterflooding techniques, thereby discouraging premature abandonment of oil leases.

Jan 1, 1961

By Martin D. Conyac

Results of the minerals survey indicate low potential for the discovery of placer gold along Deck Creek aid for copper, silver, and gold in PreTertiary rocks within the boundaries of the Lake Fork RARE II area. Potential for oil, natural gas, coal, and geothermal resources is negligible. No evidence of economic mineral resources was found during the examination of the study area, and no assays of rock or placer samples taken from the urea showed economic mineral values. There are no producing or developing mines within the boundaries o of the lake Fork study area. SETTING Mining Districts The Lake Fork RARE II area is on the eastern fringe of the Cornucopia Mining District, which is centered about 6 mi west. It is also on the western edge of the Homestead district, centered about mi east.

Jan 1, 1983

By Peter de Bakker

The objective of this contract was to develop a simple, reliable, economical, remote-control roof bolting module for installation of mechanical and resin bolts. It was to be capable of placing longer than seam height bolts, up to 10 ft lengths, from a seam height of 36 to 72 in., while keeping the operator under supported roof. The resulting machine, called REM-Bolter, is a low profile unit that utilizes Foster-Miller Flexible Shaft Roof Drill, a Bendix Roof Bolt Inserter and a newly designed. Roof Bolt Lifter/Torquer. Every effort was made to strike a compromise between complete automation and complete manual control. In a controlled laboratory environment the REM-Bolter remotely installed 1000 bolts. Subsequently the machine was tested in an operating coal mine where 500 holes were drilled (and an equal number of bolts were installed) remotely, over a 4 month period. The results of all tests Live shown that the operator of a machine of this kind can quickly, and repeatedly, install rootbolts remotely from his operator compartment some 8 ft away from the drilling/bolting action. The report includes recommendations for improvements to the present REM-Bolter design that would translate the present test bed into a second generation test bed and a potential first generation production unit.

Jan 1, 1983

By William A. Beck

The Construction Aggregates Corp. operates a plant for processing sand and gravel from two deposits in Ottawa County, Mich. The bulk of the sand is obtained from a sand dune on the shore of Lake Michigan, and the gravel is dug from a glacial-drift deposit farther inland. Mining is done with draglines, and the material, both at the digging site and in the plant, is moved mainly by systems of conveyors. The Ferrysburg plant serves customers along the Great Lakes, which is unusual for a business normally local in character. Annual production exceeds 1-1/2 million tons of sand and gravel as concrete aggregate and 200,000 tons of core sand for foundry use.

Jan 1, 1962

By M. P. Hardy

Copper-Nickel ores in northeastern Minnesota could establish a new industry in a region where underground mining has not been active. This study reviews geotechnical data relevant to the selection and design of underground mines in this region and by numerical structural analysis evaluates the importance of some geotechnical parameters to mine method selection. Because of the rapid development of computer modeling many new techniques have become available for modeling rock mass behavior in recent years. An overview of these methods is presented and their applicability to mine design reviewed. Methods included in this summary were the differential continuum models, such as finite Pint and finite difference, integral continuum models, such as boundary element, displacement discontinuity and boundary integral equation methods, and discontinuum methods such as the distinct block model. The displacement discontinuity method was used to evaluate the influence of geotechnical parameters on some aspects of mine design. Three problems; room stability, pillar stability on a weak inclined contact and sill pillar thickness influence on sill pillar stability, were analyzed to evaluate the relative importance of insitu stress field and joint properties on design. It was concluded that for stability analysis the initial horizontal stress is of most importance in all aspects of design. The position, orientation, persistence and strength of joints is also of primary concern. In a more general sense, however, it was concluded that detailed geotechnical parameters have much less influence on mine method selection than more general factors such as rock quality, initial stress state, orebody shape and economics.

Jan 1, 1978

By Howard B. Hamilton

Laboratory performance of mercury filled current limiting devices (CLD) used for high speed switching of DC circuits (600 volts and below, up to 1000 amperes) using a system involving a parallel connected vacuum switch with CLD and an additional series connected vacuum switch was verified in USBM Contract #HO 357079. This report details analytical work and field experimental tests to predict and control voltage surges associated with the high switching speed associated with the switching system. It also details tests conducted to demonstrate the fault current limiting ability of the CLD. Problems associated with designing a fault current limiting system are discussed.

Jan 1, 1978

By David E. Nicholson

The Bureau of Mines has constructed a special compression chamber for developing stress-strain relationships of mine backfill and simulating the high compressive ground pressures encountered in underground mines. A one-dimensional, or Earth-Pressure-at-Rest model is proposed for backfills subjected to these pressures. Results of the compression tests performed in the chamber indicate that reliable stress-strain relationships can be developed from these tests. The primary objective of the test series was to evaluate the effectiveness of compaction of common backfills in retarding ground closure. Analysis of the stress-strain data shows an eightfold reduction in relative strain in optimum well-graded, compacted backfills over poorly graded, loose backfill material. Analysis of the one-dimensional compression test data also indicates a significant retardation of transmitted stress in dense compacted samples of backfill and natural sands. Although not fully understood, a deformation mechanism is thought to occur at the intergranular contacts in cyclic fashion causing frictional heat loss and a reduction in transmitted stresses in the densely packed materials. The experimental values of transmitted stress are compared with theoretical values of effective stress calculated from the one-dimensional compression relationships developed by Hendron (4).3 These experimental values of transmitted stress compare very closely with the theoretical values of effective stress.

Jan 1, 1968

By Mark R. Pettitt

The development of fire hazard criteria for noise control products in underground coal mines are presented. Qualifying requisites of the criteria include maintaining miners' safety, allowing for maximum use of noise control products, and economic feasibility. The burning process is analyzed for its relationship to fire hazard criteria developed by NASA and the FAA, and the mine environment is analyzed in conjunction with the end-use applications of noise control products. Also, the interim fire hazard specification developed by MSHA is appraised as it applies to end-use applications of noise control products. From these analyses and a literature survey, fire hazard criteria are developed. They include an initial screening procedure that evaluates the level of flammability testing required. Fire tests that may be indicated are the Vertical Flame Test, the Ignition Temperature Test, and the 25-Foot Tunnel Test.

Jan 1, 1983