Search Documents

By L. B. Pankratz

The Bureau of Mines conducted heat-content measurements above 298.15° K for dehydrated analcite (NaAISi2O6) to 1,000°K, kaliophilite (KA1Si04) to 1,800° K, and leucite (KAlSi206) to 1,800° K. Heat content and entropy increments were tabulated, and the heat content data, were given in equation form. A first order transition was noted for kaliophilite near 810° K with a heat absorption of 160 cal/mole. Leucite had a second order transition which became complete near 955° K. In this transition a crystal change occurred from tetragonal (low-temperature form) to cubic (high-temperature form).

Jan 1, 1968

This report was limited to a search of available literature on under- ground methods to combat acid water pollution. From this review it is evident that very little work has been done in this specific area. It is also evident that there are specific areas of mining engineering and mining related hydrology and geology that need further research efforts to solve the many water problems. They are: (A) Composition, variation and availability for oxidation of sulfur in strata. (B) Rate of oxidation of sulfuritic materials. (C) In situ limestone and its influence on underground acid drainage. (D) Structural, stratigraphic and hydrologic character of old mining areas as a basis to make decisions about adjacent new mining areas. (E) Operational changes in mining methods to prevent pollution. (F) Sealants for underground coating to exclude water from contact with pyrite to inhibit formation of the contaminants. Such a program has been initiated on refuse piles. The prime purpose of this report is to investigate those practices which have been used to regulate or control water accumulation and prevent harmful mine drainage. A supplemental purpose is to indicate those areas which need further research to prevent underground mine water pollution.

Jan 1, 1970

Develop new technolgies and techniques which enable recovery of strategic and critical minerals such as cobalt from domestic resources, thereby easing the U.S. dependence upon foreign producers for these valuable commodities. Approach The Bureau of Mines, through research, developed a process which uses mineral beneficiation techniques to recover cobalt-rich products from Missouri lead ores. Before development of this process, cobalt was lost as an impurity in the copper, lead, and zinc concentrates and in the mill tailings because the technology to recover it with minimum impact on present production did not exist.

Jan 1, 1989

By Harry Dobroski, Larry G. Stolarczyk

Medium-frequency (MF) techniques have been successfully .[pplied] to the problem of radio voice communications in both coal and metal and nonmental mines. Long range is achieved by taking advantage of existing mine conductors that carry and propagate the signal over vast areas. It is very likely that in the near future such systems will become the referred method for general mine communications. MF techniques can also be applied to the areas of in-mine control and monitoring. Preliminary work in this area is described. In a western mine, locomotives are being operated under MF remote control in a loading operation. In several eastern mines, MF has been evaluated as a method for monitoring the status of devices in remote areas of the mines. All control and monitor information uses existing mine conductors.

Prevent collisions between large mine-haulage trucks and smaller vehicles parked in areas not visible to the haulage-truck operator, Approach Two electronic systems were developed to detect the presence of vehicles in the blind areas of a parked haulage truck. The systems can warn haulage truck operators of presence of vehicles that are blocked from view. The systems do not apply for trucks in travel. How It Works The systems use electronic transmitting techniques-one system is based on low-frequency radio waves and the other on very-high-frequency radio waves. Each system requires that a signal transmitter be mounted on the smaller vehicle to be detected. Continuous signals from this transmitter are sensed by receiving antennas mounted on the right front and rear of the large haulage truck. Upon receiving a signal, the receiver energizes warning lights and a buzzer in the cab of the haulage truck, alerting the operator to a possible collision hazard. Detection distance is adjustable, depending upon the size of the haulage truck, but a minimum of 30 feet was the design goal.

Jan 1, 1990

This study presents a reservoir modeling approach to investigate the relative effects of different coalbed parameters on the migration of methane into development entries. A base coalbed reservoir model of a three-entry development section, where grids were dynamically controlled to simulate the advance of mining at a constant section advance rate, was created and calibrated for a Pittsburgh Coalbed mine in the Southwestern Pennsylvania section of the Northern Appalachian Basin. The values of coalbed parameters were varied to evaluate their effects on predicted methane emissions for various development distances. The results of these parametric simulations were then used to derive linear expressions relating these parameters to methane emissions into the workings. These models were analyzed to assess their significance and adequacy for predictive purposes. This work shows that coupling reservoir simulations with linear modeling yield a technique that can be applicable to different coalbeds. The reservoir parameters used by the linear models (coalbed thickness, pressure, sorption time constant, Langmuir parameters, permeability) can be determined by running relatively simple laboratory tests, such as adsorption equilibrium and permeability determination, on coal samples obtained either from the mining operation or from the exploratory boreholes drilled ahead of mining.

Jan 1, 2008

To reduce the possibility of injury to operators and damage to equipment caused by collision of mining vehicles during coal loading. Approach An energy-absorbing bumper was developed and tested underground on a continuous miner. How It Works The bumper, a long box-like weldment backed by five energy absorbers, is attached to a continuous mining machine by a hinge behind the cab. See Figure 1. When a shuttle car collides with the bumper, or when it is otherwise struck, the energy absorbers are compressed. This absorbs and dissipates part of the kinetic energy of the colliding vehicle, thereby reducing or eliminating its destructive effects. Each energy absorber consists of two chambers separated by a freely-moving piston. One chamber (Figure 2) contains hydraulic fluid. The second chamber contains a gas. When a collision causes the absorber to compress, the hydraulic fluid in the first chamber is forced past a metering pin and through an orifice. The hydraulic fluid then pushes against the piston, compressing the gas in the second chamber.

Jan 1, 1978

To rapidly limit and interrupt high dc fault currents with minimal arcing in the mine atmosphere. Approach Design a dc switching sys-tem which uses a pressurized, liquid metal-filled, change-of-state device combined with a conventional interrupter and commutating switch. Direct Current Interruption Switching and interruption of large direct currents imposes severe loads on fuses, contactors, and circuit breakers in mine power systems. This problem is much more pronounced with de than with ac because of the lack of a natural current zero in dc. Dc interruption is characterized by persistent arcing that can foul contact tips and con-tribute to interrupter failures. To reduce maintenance and prolong the service life of these units, a commercially viable dc switching system has been developed by the Bureau of Mines through a research contract with the University of Pittsburgh. This system rapidly limits and interrupts high fault currents when used in combination with conventional interrupters.

Jan 1, 1983

Develop a safer, more effective, and more efficient method to control fires in abandoned coal mines and waste banks. Maintain the costs of this new method at less than or comparable to conventional AMI fire control methods. How It Works Cryogenic extinguishment of subsurface fires is a method of heat transfer. Bureau-designed injection equipment produces a pumpable slurry of liquid nitrogen and solid particles of carbon dioxide. Liquid or gaseous carbon dioxide from a pressurized tank flows to a bell-shaped nozzle where the change in pressure causes the carbon dioxide to form a granular snow. The solid carbon dioxide is mixed with liquid nitrogen. A jet pump is used to move the slurry through the delivery lines and into a simple injection probe. At injection, the nitrogen vaporizes and the carbon dioxide sublimes. This phase change produces a cold gas (-180° C) that, as it expands and moves in all directions, removes heat and also displaces oxygen. This combined process inhibits the combustion process and lowers the temperature below the reignition point. When the liquid nitrogen and solid carbon dioxide are converted to gases, the expanding gas acts like a piston, forcing warm air out of the porous bed, Although smoke and hot gases arc forced from the burning coal, generally there is no significant increase in the odor associated with burning coal.

Jan 1, 1992

Continuously separate mixture of non-magnetic materials (such as scrap, precious metals, or certain ores) at a reasonable cost. Approach Nonmagnetic materials of different densities are rapidly float/sink separated by an augmented lifting force produced In a magnetic fluid (liquid) by the effect of an external magnetic field. The magnetic fluid is a colloidal suspension of magnetite In kerosene, prepared by a low-cost process. How It Works Separation is accomplished in an open trough filled with magnetic fluid. A magnetic field is established in the fluid, by energizing an electromagnet having poles on each side of the trough. Due to the design of the magnet poles and air gaps, the magnetic field is strongest at the bottom, about 10,000 oersteds, and uniformly decreases in strength to about 2,000 oersteds at the top of the fluid. Therefore, the magnetic field gradient increases with depth. The magnetic force attracts the entire separation medium (magnetic fluid) creating a reaction force of equal magnitude and acting in the opposite direction. This reaction created within a magnetic fluid/magnetic field combination is called a magnetic levitation force. It increases with the field strength. In this case because the magnetic field is strongest at the bottom of the trough, the magnetic levitation force will quickly float lighter material while heavier material sinks.

Jan 1, 1980

Reduce rockfall fatalities and injuries by using innovative blasting practices to reduce damage to the rock at the excavation limits with little or no increase in cost. The Problem Falls of highwall have been a leading cause of fatalities, injuries, and equipment damage in the surface mining industry. Although the number of highwall falls is not great, when such an incident does occur it is about 14 times more likely to be fatal or result in severe injury and damage to equipment than other types of surface mine accidents. Overbreak or damage to the rock from poor or improper blasting practices is a major factor contributing to rock falls. Presplitting or cushion blasting is the technique most often recommended for improved wall control. This type of blasting however, adds to drilling and blasting costs and is not universally accepted by the industry. Air gap presplitting techniques, also called air decks, are currently being used in some mines as a less costly alternative to conventional presplitting. Approach Blasting can cause highwall damage, but proper blasting techniques have been shown to reduce the magnitude of rockfall problems. In preventing rock falls, it is important to maintain the natural strength of the rock structure to the greatest extent possible. Improved blasting practices have three main advantages: 1) they are preventive rather than corrective in nature; 2) they are cost effective; and 3) they have a very low impact on the mining operation when properly implemented. New ways of evaluating highwall integrity, such as seismic refraction tomography, were investigated.

Jan 1, 1991

By E. J. Gleim

During the past 10 years the Bureau of Mines has had a broad experience in the tasting and inspection of electric motors for gaol-cutting machines, cowl drills, storage-battery locomotives and other equipment Which is used in mines where explosive mixtures of methane and air may be encountered. From this experience the Bureau's engineers have reached the conclusion that the most satisfactory method of protecting a motor so as to prevent any sparks resulting from rough commutator, loose contacts or short-circuits in it, from igniting he surrounding atmosphere, is to totally inclose the motor with a substantial casing; having flanged joints. These joints should be metal-to-metal contact so that the shortest path from the interior to the exterior Of the casing is not less than one inch in length. On account of this experience with mining machinery, the Bureau has been asked whether an equal or loss degree of protection would be sufficient for motors for service in or about places such as refineries, gasoline filling stations, cleaning establishments and pumping stations, or in any place where there is liklihood of explosive mixtures of gasoline or naphtha vapors and air accumulating.

Jan 1, 1922

To enhance safety and efficiency when moving large mining equipment under energized trolley lines, and to assist in compliance with Section 75.1003.2, 30 CFR. Approach A system was designed, using established technology, that permits a remotely located circuit breaker to be controlled from the cab of a mine locomotive moving large mining equipment under energized trolley lines. This control consists of setting the desired trip current, automatic or manual tripping, resetting, and voice communications between the locomotive and a remote Circuit breaker location. How It Works According to 75.1003.2, 30 CFR, whenever a piece of off-track equipment (such as a longwall chock or a continuous miner) is moved by rail under energized trolley or feeder lines, power for the locomotive that is moving the equipment must come from only one' circuit breaker. This circuit breaker must be adjusted to permit no more than one-half its rated short-circuit current to flow. The intent is to lessen the danger if an accident should occur, and if the equipment contacts the trolley line. Even so, the danger is great. This half setting can still represent many hundreds or even thousands of amperes, enough to endanger personnel, the equipment, or the mine. The Remote Control System reduces this danger substantially by giving the personnel associated with the move total control over the associated circuit breaker. The system as designed, is intended to be used with portable circuit breakers that are pulled on a small flat car by a mine jeep, and either precede or follow the equipment, depending on the direction of the power. This portable circuit breaker is equipped with a commercially available solid state overcurrent relay and associated shunt. This circuit breaker is connected via heavy duty clamps around an open trolley line tie breaker such that the current through the shunt is also the current in the trolley line. A receiver, interfaced with the overcurrent relay and shunt, completes the remote system.

Jan 1, 1981

Introduction The Coal Mine Roof Rating (CMRR) is a roof classification system. It was first introduced to the mining community in 1994.The CMRR filled a longstanding need to quantify geologic description of coal measure rocks into an engineering value that could be used for mine design. It has now been written to a user-friendly visual basic code that can be run on any PC with a Windows operating system. Background Rocks that form the roof of coal mines can vary widely and quickly in composition, extent, and defects. This results in an equally broad range of rock properties that can substantially affect the ability of the rock mass to form a stable mine roof. The CMRR was designed to evaluate the properties of the coal mine roof rock mass that contribute to its weakness and convert them into a relative strength rating from 0 to 100. These properties include the cohesion and frequency of discontinuities like bedding, slips, shears, and joints; uniaxial compressive strength (UCS); and moisture sensitivity. With simple lab and field tests and observation, the CMRR can be calculated by technical and operating personnel with a minimum of training. The CMRR has been widely accepted in both U.S. and international coalfields. As a result, a number of roof control applications have been found for the CMRR. It is currently used as an input component in the Analysis of Longwall Pillar Stability(ALPS) program, which is used to design longwall chain pillars. Incan be used as a criterion for determining the appropriate width of mine entries. It has also been used to indicate the appropriate length of cut in weak ground. The CMRR can be used as a strength parameter to characterize inter burden between mined seams in the numerical modeling of subsidence effects. In any area where an estimation of coal measure rock mass strength is required, the CMRR can be adapted to fill this need. How It Works Originally designed to be used with underground exposures, the CMRR can also be calculated from core. The chisel test for bedding cohesion and the ballpeen hammer test for UCS are inappropriate for core. These tests have been replaced by point load testing both axially and diametrally. Two other measures that are common to standard core logging—Rock Quality Designation (RQD) and fracture spacing—are also used to estimate rock weakness. With these easily obtained parameters, the CMRR can be calculated from core and used in the mine planning and exploration phase. The input screens allow calculation of the CMRR for both underground exposure and core. The CMRR is reported both as a “dry" value and as a groundwater-adjusted value for moisture-sensitive rocks. There is a graphical output report featuring a lithologic column with annotated unit ratings and a roof bolt symbol representing the height of the bolted horizon. Another important feature is an AutoCAD interface. This feature allows the export of located CMRR data directly to an AutoCAD layer in XYZ form. In this way, drill hole data can be inserted directly to a base map.

Apr 1, 2003

By Robert King

Splicing portable trailing cables used in underground coal mines is usually less expensive in terms of capital outlay and production time lost than replacing them. However, handling trailing cables may result in electrical arcs, shocks , and burns. Also, destructive forces encountered during a mining operation may shorten the effective life of a cable splice. This report gives the results of an analysis of cable splice defects in an effort to establish cable splice performance criteria, determine testing standards for cable splices, establish guidelines for training programs in cable splicing, and indicate areas for improvement.

Jan 1, 1975

By Garrett R. Hyde

Sintered yttria and sintered dysprosia can be used to make single-component thermistors having typical thermistor geometries and operable in the temperature range 500° to 1,200° C. However, at these temperatures, instability of platinum electrodes can contribute a slight aging effect if the thermistor is kept near 1,200° C for long periods. Typical characteristics at 500° C for an yttria disk thermistor 12 mm in diameter and 2 mm thick are a resistance of 12.4 megohms and a temperature coefficient of resistance of -3.8 percent per degree C. Typical characteristics at 500° C for a dysprosia thermistor of the same dimensions are a resistance of 1.84 kohms and a temperature coefficient of resistance of -1.6 percent per degree C.

Jan 1, 1970

Provide an instrument for continuous remote monitoring of carbon monoxide concentration in underground mines. Approach A carbon monoxide fixed? point continuous monitor consists of two modules. A line-powered control module is designed to power a remote transducer module; provide continuous readouts, visual and audible alarms, operational checks; and activate fans and equipment shutdown circuits if preset CO concentration levels are exceeded. How It Works The control module must be used in conjunction with a single transducer module. Developed under contract. the control module is a wall-mounted Instrument which contains a readout and alarm capability and power supply

Jan 1, 1981

By Launa Mallett, Charles Vaught, Michael J. Brinich

The lack of good communication is a very real problem in mine emergencies. Sometimes critical information is not communicated to those who need it to make decisions. At other times, those on the receiving end of a warning do not think to ask the right questions. What happens in underground coal mine fires is a case in point. The authors interviewed 48 workers who escaped three serious fires in western Pennsylvania. In each case the location of the fire was known but did not get communicated to many of those who had to evacuate. Sometimes, even the nature of the problem was not clearly communicated. Some workers began their evacuation knowing nothing about what was happening. In an effort to improve emergency communication National Institute for Occupational Safety and Health (NIOSH) researchers worked with safety professionals to determine what sorts of information are critical in a mine emergency. An extensive list was generated, which proved too long to be remembered by individuals. The list was therefore collapsed into six categories. A communication protocol was derived from these categories.

By Ann G. Kim

Gas samples containing 02, N2, H2, He, CO2, CO, CH4, and trace amounts of C 2 to C6 hydrocarbons are analyzed by a gas chromatographic method that utilizes both thermal conductivity and flame ionization detectors. A porous polymer support and molecular sieve columns are used with argon as the carrier gas. A column selector valve makes it possible to perform a complete analysis either on one 1-ml sample in 40 minutes or on two samples in 20 minutes, one sample for each detector. Samples are introduced either by on-column injection or through a gas sampling valve. By varying operational parameters, the speed, sensitivity, and accuracy of analysis may be modified to suit a particular situation.

Jan 1, 1974

Reduce the number of accidents caused by slips and falls from large mining equipment. Approach A powered lift was developed that provides operators with a safer way of getting on and off large machines. How It Works The powered step is designed to lift personnel and materials to working levels on large machines. It eliminates hazardous blind steps and makes it unnecessary to climb on irregular surfaces made slippery by mud, ice, snow, and accumulations of grease. The step is powered by a self-contained electric/hydraulic unit which is connected to a vehicle's auxiliary power supply. When in the "down" position, the step rests about 15 inches above ground level. When the power unit is activated with an electrical switch located on the step, a Single cylinder attached between two lifting arms smoothly lifts the step. In conjunction with the lifting motion, a linkage and bearing arrangement on the mounting end of the lift arms causes the step to rotate towards the machine, so that the step moves in an arc from ground to platform level. When the machine Is operating, the step is automatically locked in the "up" position, protecting it against any damaging contact with obstructions. The step is lowered by activating a pressure release solenoid. An in-line orifice controls downward speed and prevents free fall. On most machines, additional control switches are conveniently located at ground level and in the operator's cab. Visual alarms and machine interlocks are provided where necessary to prevent machine operation when the step is In the "down" position. The powered step can be easily adapted to any type or model of large machinery.

Jan 1, 1981