Search Documents

By T. E. Sterner

A laboratory investigation was conducted to determine the applicability of the thermal oil-recovery method as a means of increasing ultimate oil recovery in the Appalachian region. The primary objective was to establish self-sustained combustion in consolidated and unconsolidated sand test assemblies saturated with various amounts of Pennsylvania Grade crude oil and synthetic brine. Tests using blocks of sandstone were unsuccessful because of sealing problems and fracturing of the rock due to thermal stresses. A combustion wave of about 700° F was propagated through the sand-oil-water packs in the linear tube tests. The high air flux used resulted in high oil consumption and rapid movement of the combustion wave through the tubes. Analytical tests on the sand pack showed that sufficient fuel was deposited during the linear tube experiments for a self-sustained combustion wave.

Jan 1, 1967

By F. E. Griffith

Cost data are given for five methods of secondary backfilling of strip mines previously partially backfilled. The operations were conducted in north-central Pennsylvania; an average of 600 linear feet of highwall were backfilled in each trial. Major obstacles and the relative merits of the methods are discussed.

Jan 1, 1966

By E. D. Gardner

"The Bureau of Mines receives many inquiries concerning favorable areas in which to prospect for gold, procedure to be followed, equipment required, and allied subjects. This circular has been prepared for use in reply to these inquiries.Interest in gold mining and prospecting for gold remains steady. From time to time many people take to the field to search for new gold deposits. A large percentage of them have had no previous experience in prospecting for lode gold; this paper has been written with the hope that it might assist these newcomers.A majority of the metal mines in the United States have been discovered by qualified prospectors who were searching for valuable minerals at the time. Chance, however, always has played a large part in finding mineral deposits. Some of the discoveries of the past were made by men on other errands, such as rounding up burros or hunting game. Accidental discoveries of ore bodies have been made in building roads and trails and in excavating for mine struc¬tures. Evidence of ore has been brought to the surface by burrowing animals and by ants; gold found in the craws of fowl has led to discoveries of deposits. Important discoveries have been made by men who had no knowledge of rocks or minerals; on the other hand, many ore bodies have been found by experienced prospectors, sometimes after hundreds of untrained men had already passed over the ground.The prospector who carries on his work diligently and intelligently is of course more likely to be rewarded for his efforts than the lazy or unintelligent worker; nevertheless, it is obvious that if valuable deposits are not present at the place being prospected none will be found. Conscientious and painstaking efforts to trace gold to its source usually disclose nothing more valuable than some narrow, unworkable seams; however, many deposits that were developed into profitable mines were found by this method of prospecting. Although some prospectors have made several lucky strikes, many others have spent their working lives searching for gold without finding anything worth while. Probably only one prospector out of several thousand ever finds anything worth developing. Moreover, only 1 out of every 300 or 400 properties developed becomes a profitable mine.Prospecting was begun in the Western States in the fifties as the miners looked for the source of gold found in placers. The search for gold has been continuous since that time; the number of prospectors in the field at any one time, however, has varied greatly. Except in some desert regions, practicallyall of the placer fields now being worked were discovered by old timers; more-over, most of the important gold districts were found by early prospectors. Important discoveries of lode mines, however, have been made from time to time. Most of the area in the mining regions of the West has been searched many times by prospectors, and nearly all of the easily found deposits have been located, but it is reasonable to expect that new gold mines will continue to be found. Most of the future discoveries undoubtedly will be of deposits that do not outcrop. Prospecting for such deposits requires considerable digging.Several important discoveries were made in 1934. One of these, the Rogers-Gentry gold mine at the edge of Antelope Valley in Los Angeles County, Calif., was found by an experienced prospector on an old patented homestead a number of miles from the nearest producing mine. The initial discovery at this mine was an iron-stained, decomposed, silicous limestone outcrop, with no vein structure evident at the surface, near a small, barren quartz outcrop and a water seep. Another discovery, the Silver Queen gold mine, in the same general region and near Mojave, Calif., was found by an experienced miner on an open fraction 400 by 1,400 feet in size between two old properties that were thought to have been worked out years ago. The Silver Queen discovery was made as the result of finding a"

Feb 1, 1950

By T. G. Carnahan

The Bureau of Mines conducted research to simulate in situ leaching of a porphyry copper sulfide ore. The purpose was to determine the effects on copper leaching of additions of NaCI to a conventional sulfate leach system and to analyze the oxidant requirements and the oxidation products that resulted from leaching of the sulfide minerals in the ore. Baseline sulfate and sulfate plus 2-pct-NaCl-leach-solution experiments employing 167-kg (367-lb) and 152-kg (333-lb) charges, respectively, were conducted. The minus 25.4-cm (10-inch) ore was leached at 90° C under flooded conditions with 2.8 MPa (400 psig) of oxygen bubbling through the system. Sixty-seven pct of the copper was extracted in 1,236 days of leaching in the NaCI experiment, whereas 47 pct of the copper was extracted in 913 days of leaching in the baseline experiment. Diffusion into and out of the ore fragments controlled the rate of leaching, which precluded enhancement of the leach rate by the chloride ions. The calculated oxygen consumption was 3.17 kg/kg of copper extracted in the baseline experiment and 3.46 kg/kg of copper extracted in the experiment to determine the effect of chloride ions.

Jan 1, 1982

By James H. Russell

Several solid sorbents were compared for their effectiveness in removing sulfur dioxide from flue gases. The materials were tested for the rate of sorption and capacity at about 300° C, and rate of regeneration around 700° C in thin beds and in 4-inch-diameter fluidized beds. Rates of material loss were also estimated. The sorbents tested included three samples of alkalized alumina, two samples of sodium carbonate-impregnated alumina, and one proprietary sample of porous silica impregnated with copper and iron compounds. The results showed that all the alkalized aluminas had good sorption capacities and rates, required high temperature regeneration, and suffered excessive material loss; the sodium carbonate-impregnated aluminas (1) had high sorption rates but barely adequate capacities, (2) required high temperature regeneration, and (3) suffered excessive material losses; and the copper-iron impregnated silica suffered only slight material loss and could be regenerated at a relatively low temperature, but the sorption rate and capacity were too small. None of the sorbents met all the arbitrary performance criteria that follow: sorption rate constant of 1 min-1, sorption capacity of 0.1 g sulfur per g sorbent, regeneration rate constant of about 0.075 min-1 at a reasonable temperature, less than 0.07 pct per hour material loss during operation, and a chemical life of 500 cycles.

Jan 1, 1971

By Robert J. Timko, Edward D. Thimons

Sulfur hexafluoride (SF6) is an odorless, colorless, nontoxic gas that has found acceptance as a tracer gas in research on ventilation pat- terns, measurement of air leak rates, respirable dust reductions due to bagging hood modifications, and the study of airflows relating to gob boreholes. Following a short review of the SF6 sampling technique, this report describes recent Bureau of Mines projects in which SF6 was used successfully as a tracer gas, enabling researchers to acquire representative data quickly and inexpensively.

Jan 1, 1982

By A. J. Rambosek

An evaluation of diamond-bit performance data accumulated from core drilling in quartzite shows that core recovery and physical characteristics of drill bits and diamonds have economic significance. Relatively inexpensive, low-quality, small Congo diamonds will perform as well as, or better than, other diamonds used as drill bart. M-type bits set with oriented Congo diamonds provide those engaged in core drilling with near optimum combination. Various factors that affect bit performance, including size of diamonds, size and type of bits, grade or quality of diamonds, and percentage of core recovered, are evaluated by means of tables, charts, and discussion.

Jan 1, 1958

By G. H. Hopkins

Like most industries, the refining industry has in recent years been confronted with the problem of a decreased martin of profit, due both to a general lowering of prices and to rising costs. This has resulted in accelerating a program of increased efficiency an evidenced by improved methods and the installation of equipment designed to affect a number of economies hitherto regarded as unimportant. Perhaps the most important of these has been that of fuel economy for, as is not often realized, a refinery consumes about one-tenth as much fuel as it produces. A recently completed canvas., made by the Bureau of Mines for the purpose of determining the trend of fuel consumption at refineries in the United States, showed the following outstanding points, (1) a decrease in the use of oil for fuel in 1926 of approximately 4,000,000 barrels as compared with 1925; (2) a small decrease in the use of coal; (3) a material increase in the use of gas, both natural gas and refinery gas; and (4) a considerable increase in the use of petroleum coke.

Jan 1, 1927

By P. W. Jerant

The methane emissions from an advancing coal mine section were continuously monitored for 120 days. During this time, the section advanced 2,000 feet into virgin Pittsburgh coalbed producing 54,565 tons of coal with a total methane emission of 91 million ft3. Analysis of the data gathered showed that daily methane emissions did not correlate with overburden thickness and daily coal production. A good correlation was found between the daily methane emission and the average length of rib exposed to virgin coal.

Jan 1, 1976

By John C. Edwards

The Bureau of Mines has developed a time-dependent mathematical model of radiative heating of bulkheads in mines. The model includes both reradiation from the duct (cylindrical) walls and direct radiation from the fire zone. Thermal loss into the wall of the duct and into the bulkhead is included. Both brick and wood bulkheads are considered. It is found that the heating rate of the system scales as the duct length-to-diameter ratio and the flame temperature. In particular, the time required for the irradiated surface of the bulkhead to reach a specified temperature decreases with increasing flame temperature for a fixed length-to-diameter ratio and increases with increasing length-to-diameter ratio for a specified flame temperature. It is also deter-mined that the time, T, for the bulkhead surface temperature to reach a specific value, Tb, for a fixed length-to-diameter ratio less than 4 and for a flame temperature of 1,200 K is approximately linearly dependent on Tb for 500 K < Tb < 700 K, and is nearly exponentially dependent on the length-to-diameter ratio for Tb = 600 and 700 K.

Jan 1, 1979

By Jack E. Fraley

Magnesium oxysulfate cement has been specially formulated as a sealant in underground coal mines for reducing sloughing of shale roofs and coal ribs, for reducing air losses through block stoppings, for constructing sprayed stop-pings over approved jute cloth or metal lath, and for reducing combustibility of polyurethane foam. A standard spray machine (Mining Enforcement and Safety Administration (MESA) approved) was used for the underground testing. Our research shows that a 1/2-inch coating reduces shale and coal sloughing, reduces air losses through block stoppings, and prevents fire propagation through a metal tunnel lined with polyurethane foam. During the underground tests, excess mixing water was used to improve pumping the slurry to the spray nozzle. This was later found to increase shrinkage cracks in the cured coatings. Controlling excess water is important to an acceptable coating.

Jan 1, 1976

By Van E. Shaw

Fusion of an 86-percent euxenite concentrate with ammonium sulfate was investigated by the Bureau of Mines. Reaction for 4 hours at 400° C results in conversion of both the rare-earth elements and the titanium-columbium components to water-soluble compounds. Similar results are obtained with ammonium bisulfate. Stirring the fusion mass decreases the reaction time substantially. Alternatively, treating the fusion product with a 3-hour, 650° C calcining step renders the non-rare-earth constituents insoluble, thereby allowing selective leaching of a pure rare-earth fraction with an overall yield of 97 percent.

Jan 1, 1967

By John L. Ellenberger

The Bureau of Mines investigated the occurrence of slickensides in mine roof in the Pittsburgh coalbed in a portion of the Valley Camp No.3 mine in southwestern Pennsylvania to improve the potential for prediction of slicken-sided zones and determine the orientations of the most prominent slickensided planes. Two distinct types of slickensides were identified; those which were associated with clay veins observed in the coalbed (genetic), and those which were unrelated to any visible structure (nongenetic). The study draws three conclusions: (1) Nongenetic slickensides are not the result of tectonic forces, (2) both genetic and nongenetic slickensides tend to dip at an angle of 30°, and (3) genetic slickensides tend to be alined parallel to the trend of the clay vein and usually dip toward the center of the clay vein. A schematic roof bolting plan is presented that may provide improved roof support where slickensides are present. Roof stability could be improved by supplemental bolting in the direction normal to the plane of slickensides.

Jan 1, 1979

By C. W. Owings

When explosions have occurred in mines where rock dust has been used to some extent, generally to a very limited extent, the press has immediately characterized those mines as "rock-dusted." To persons familiar with the method of rock-dusting, it is apparent that if rock-dusting is done properly, if all mine surfaces are rock-dusted to within at least 40 feet of the faces of rooms and entries, and if the incombustible content of the dust is more than 65 per cent, there is little likelihood that an explosion of coal-dust will occur. The report that an explosion has occurred in a "rock-dusted" mine immediately conveys to the mind of the alert safety advocate the information that the mine is inadequately rock-dusted or that either dust sampling of the rock-dusted surfaces has not been done or, if done, the mine has not been redusted with sufficient promptness. Rules for Collection of Samples Collection of dust samples is by no means intricate, but a few simple rules must be kept in mind if the results are to be dependable. A sample must represent the true average conditions of the dust in the section or zone in which it is taken, and therefore &apos;the point at which the sample is to be collected must be selected with care. During an explosion much if not all of the dust on the ribs, roof, timber, and road in the affected region is blown into the air; the sample, therefore, should contain all loose dust and material on: the surfaces to a depth of about 1 inch, if that amount is present. If there is considerable sand locally along the track, care must be taken not to include enough of this material to vitiate the sale and distort the results; however, if the sand is distributed throughout the region being sampled it should be included. Dust should not be collected from recesses in the ribs, such as hitches cut for timber, as the character of the dust in such places is often different from that on the ribs proper. Samples should not be collected at points where the dusting machine has been loaded or at a point where the machine has stopped and discharged for a longer period than at other points on the entry or in the rooms. In short, the sample must represent AVERAGE CONDITIONS, and if there is any doubt as to the character of the dust it is far better to have too much combustible matter than too much incombustible matter in the sample, as it is best to err on the side of safety if it is necessary to err.

Jan 1, 1929

By Clarence O. Babcock

This Bureau of Mines report presents the initial development of a two-dimensional method of analysis for inclusions in plates in which the deformed shape of an open hole and the separate structural behavior of inclusion and plate with hole are used to obtain the stresses and strains in the inclusion only. In this report the solution for a circular inclusion is presented because a direct verification of the results with previous solutions was possible. The numerical results were in exact agreement with those obtained with the equations of Sezawa and Donnell. The equations developed are less complex than those of Sezawa and more general, for a circular inclusion, than those of Donnell. Stresses and strains in the inclusion are in terms of the elastic constants of the inclusion and the plate and the biaxial stress field applied far away. The elastic constants can be all different. An important conclusion from this work is that a difference in Poisson&apos;s ratios between inclusion and plate may be as important as a difference in Young&apos;s moduli between inclusion and plate in producing the inclusion effect. Many problems in mining and rock mechanics can be treated as inclusion problems. The understanding of inclusion behavior on a physical basis should provide the solutions to some of these problems.

Jan 1, 1974

By R. E. Brown

The objective of this Bureau of Mines study was a laboratory-scale evaluation of the sodium sulfate refining process for removing copper from molten ferrous scrap. Maximum copper removal is achieved in carbon-saturated melts at 1,300° C. Low carbon concentrations and higher temperatures result in a less efficient copper removal and an increased sulfur concentration in the iron. Sodium sulfate refining significantly lowers the concentration of aluminum, manganese, and silicon; however, the copper removal efficiency is adversely affected by the presence of manganese and silicon. Compared with other reagents tested, sodium sulfide-forming slags were found to be the most suitable for both copper removal and sulfur control. The sulfur content of the refined iron was higher in tests conducted in acid-type refractory crucibles. Earlier studies showed that tin, a significant metallurgical impurity, is not removed by the sulfate process. During the present investigation, results showed that chlorination, using organic solid sources of chlorine, reduced the tin concentration to acceptable levels in molten iron.

Jan 1, 1975

By Bruce T. Olenchuk, Wils L. Cooley

Electrical grounding is essential for the safe operation of power systems. A low-impedance path to ground is necessary to prevent the possibility of dangerously high potentials in human work areas. If for any reason this ground connection becomes faulty, a serious hazard may exist. One reason for faulty ground connections is ground bed corrosion. Corrosion of electrical ground rods has plagued the power industry and appeared in coal mine power systems. This paper will investigate ground rod corrosion, its cause, and possible solutions. Included is an evaluation of various ground rods for their ability to resist corrosion under stray current conditions. -The first known study of X-it3 Rod Corrosion is also presented.

Jan 1, 1979

By Steven J. Page, William A. Heitbrink, Andrew B. Cecala, Edward D. Thimons, John A. Organiscak

Miners at noncoal surface mining operations are often exposed to high levels of respirable dust. In an effort to lower the respirable dust exposure of these surface miners, the National Institute for Occupational Safety and Health (NIOSH) has been conducting research to address this problem in a practical and economically viable manner. One successful effort deals with lowering the dust exposure of equipment operators in enclosed cabs. Many types of surface mining equipment utilize enclosed cabs to protect equipment operators from dust exposure. Normally when the equipment is new, the cabs are fairly airtight. These tightly sealed cabs, combined with good filtration systems, generally provide the operator with good dust protection. However, most mining equipment is older, and as aging occurs, many components of the enclosure deteriorate. The structural integrity of the cab diminishes and the effectiveness of the air filtration system fails. NIOSH has been successfully researching costs-effective methods to improve both filtration effectiveness and cab integrity of these older cabs in order to provide a healthier work environment for equipment operators. Dust sampling records indicate that drill operators and helpers have the highest dust exposure of all workers at surface mining operations. Since much of the overburden contains a high percentage of silica, the health hazard associated with this dust can be even more serious. NIOSH research is addressing techniques to lower respirable dust levels at surface drilling operations. INTRODUCTION NIOSH&apos;s mission is to assure a safe and healthy work environment for the working men and women of this nation. The primary emphasis of NIOSH&apos;s Pittsburgh Research Laboratory (PRL) is mining health and safety research. This report focuses on two areas of research

By F. N. Kissell

The Bureau of Mines used sulfur hexafluoride (SF6) tracer gas to evaluate the effectiveness of gob ventilation and/or sealing practices at three coal mines, each having different problems associated with their mined-out areas. The purpose of these ventilation studies was to better understand whether current techniques employed for ventilation or sealing are successful at minimizing the potential for gob fires and explosions. The work performed at each mine is discussed: One is a long-wall operation that uses ventilation to carry off hazardous gases, and two are room-and-pillar operations, each with far different concerns, that seal off the gobs to isolate them from the main mine ventilation. In all cases employment of the Bureau&apos;s SF6 tracer gas technique resulted in answers to questions raised by the mine operators concerning the effectiveness of their gob ventilation or sealing practices in preventing mine fires.

Jan 1, 1986

By Jeffrey B. Osmint

The Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau&apos;s data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority fur the Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96479, 96th Congress), which strengthens protection fur proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1991