Search Documents

By Allen D. Look, J. Howard Bird

"INTRODUCTION The Phelps-Dodge Corp. New Cornelia Branch open-pit copper mine operated without a fatality in the drilling and blasting department from December 13, 1937, to April 1, 1947, and continuing.Between the dates named the explosives crews had a total of 746,520 man-hours of exposure and handled 12,000 tons of explosives, over 770,000 detonators, 2,300,000 feet of fuse, and 7,700,000 feet of Primacord in loading holes to break 116,780,000 tons of material.It is the purpose of this paper to record the procautions taken to insure safe handling of explosives at this operation where safety is definitely a matter of forethought rather than chance.GENERAL INFORMATIONThe New Cornelia Branch open-pit mine operates on a large, low-grade, disseminated-copper deposit about one-half mile south of Ajo, Ariz. The pit is approximately oval; the ore body being some 4,800 feet long and 2,750 feet wide. Ore is mined with electric shovels loading into railroad cars. All benches in- the pit are 40 feet in height except two, which are 60 feet high.The New Cornelia ore body differs from most porphyry-copper deposits in being hard and siliceous. In common with the other low-grade porphyry-copper deposits, continued operation is possible only with economical handling of large tonnages. This has necessitated a great deal of study in the evolution of a safe and efficient method of handling the large quantities of explosives needed in breaking this hard-rock material."

Feb 1, 1948

By Walter W. Fisher

Cement copper was flash roasted in a vertical tube furnace to convert the copper to acid-soluble oxides as part of a postulated process for refining cement copper by oxidation roasting, acid leaching, and electrowinning. The results of the study showed that the oxidation was a linear function of oxygen concentration between 0 and 20 percent, but above 20 percent oxygen there was no further increase in oxidation. Therefore, air was the optimum oxidizing atmosphere in this flash roasting system. The oxidation followed a parabolic rate law as the roasting temperature was increased from 400° to 800° C. Extrapolation of the data, based on the parabolic law, indicated that at 400°, 500°,600°,700°, and 800° C, the roasting times required for complete conversion to soluble oxides were 75, 37, 21, 7.7, and 4.6 seconds, respectively. Cyclic-roasting test results did not substantiate the predictions obtained through data extrapolation.

Jan 1, 1973

By Dennis R. Dolinar

The danger to personnel, equipment, and pillar structure created by the spalling of a coal rib can be minimized by installing rib bolts. To assure that a configured support system will maintain a coal rib, the U.S. Bureau of Mines developed a rib bolt system based on a nonpreventable failure concept. A statistical equation quantitatively relates the amount of rib retained to the bolt spacing and the width of the spalled material. Laboratory test results show that the equation accurately predicts the amount of material retained and confirm the validity of the support concept. The examination of rib bolting at a coal mine experiencing rib sloughage provides evidence that the effectiveness of the support can be related to the failure pattern of the spalled material. An analysis of roof and roof support reaction to rib sloughage at the mine indicated that the rib sloughage had little effect on roof stability. Although supporting ribs might not affect roof stability, laboratory test results indicate that the material retained by the support can sustain a load up to 20 pct of the intact compressive strength of the material.

Jan 1, 2010

By W. L. Hunter

Eleven steelmaking heats are described in this Bureau of Mines report in which acid practice was used to produce carbon steel from pre reduced iron ore pellets. Furnace slags obtained with no flux addition to the charge became quite viscous as they cooled, which precluded pressure casting from a ladle. Lime was added to the furnace charge at two levels to eight of the heats to modify slag characteristics in the furnace, and to the ladle in two heats to further modify the ladle slag cover. Selected ingots from nine heats were successfully rolled on a commercial mill to produce No. 10 reinforcing bar.

Jan 1, 1974

By R. J. Shanley

This report presents a computer code that has been developed by the Bureau of Mines for isolating naturally occurring clusters of data plotted on the unit hemisphere and testing these clusters against a probability distribution which admits elliptical symmetry about its mean. A listing of the computer code is provided along with an example output illustrating the delineation and analysis of clusters in fracture orientations measured in a porphyry copper deposit.

Jan 1, 1975

By John P. Conway

This Bureau of Mines investigation was undertaken to determine the feasibility of lock-bolt support in Tertiary-gravel material. Pull tests were performed on five types of rock-bolt anchors to determine their optimum anchorage capacity. Four of these anchors are commercially available; the fifth, an explosive-anchor bolt, was developed by the Bureau of Mines. To increase anchorage capacity, epoxy grout was used with several of the commercial types of bolt. Tests showed that sufficient anchorage could be obtained by employing epoxy-resin grout with the commercially available wedge bolt, or by using the explosive-anchor bolt. Also estimated are bolt spacing and cost of a rock-bolt support system.

Jan 1, 1971

By Paul S. Lewis

The Bureau of Mines hydrogenated coals of different rank that had been irradiated with either x-rays or gamma rays. Lignite, high-volatile A and C bituminous, and low-volatile bituminous coals were exposed to l billion roent¬gens of gamma-ray radiation; specimens of high-volatile A and C bituminous coals from other sources received 6 million roentgens of X-ray radiation. Irradiated and unirradiated control specimens of those coals were hydrogenated in autoclave experiments at (6,000-p.s.i. final pressure and 400° C. with retention times of 15, 30, or 60 minutes depending on the coal rank and catalytic treatment. Comparison of results from irradiated specimens with those from the control experiments showed that the radiation had no beneficial effect on the coal. High-volatile C bituminous coal may have been affected by radiation more than the other coals. One billion roentgens appeared to reduce the amount of coal converted to liquids and gases by about 10 pct., and 6 million roentgens reduced it by about 6 pct. then catalyzed with tin. In all other cases, the conversion of irradiated coal was either reduced by as much as 4 pct. or was essentially the sank as that obtained with unirradiated coal. Irradiation during hydrogenation nay be effective for increasing the reactivity of coal and should be investigated; further work with coals irradiated prier to hydrogenation is not recommended.

Jan 1, 1962

By Albert E. Long

Diamond-bit performance and cost data accumulated in core-drilling sandstones reveal significant trends of economic interest. Large-size, AA-Grade drill bort suffered less diamond loss per foot drilled than any other size or grade of diamonds assessed. Detailed analyses of the factors that affect diamond-bit performances -diamond size, diamond quality, bit size, bit type, percentage of core recovered, and physical characteristics of bit matrices -are assessed in the tables, graphs, and discussion. INTRODUCTION Since 1945 the Bureau of Mines has been compiling detailed performance records on diamond bits used in core drilling throughout the United States and Alaska. Analytical reports covering bit performance in various rocks are issued as in-formation on a significant number of bits used in anyone type of rock is accumulated. The first three such reports analyzed bit performance in gneiss,2/ schist,3/ and lime-stone and dolomite.4/ This report evaluates diamond-bit performance in sandstone. Data obtained from 627 bits, which drilled 42,665 feet on 45 different projects, are presented. The geographical distribution of the projects is shown in figure 1.

Jan 1, 1958

By Yael Miron

Ammonium nitrate-fuel oil (AN-FO) mixtures are used as blasting agents in mining pyrite-bearing ores. The temperature of these ores can increase by the continuous, though at times slow, oxidation weathering of the pyrites. At elevated temperatures, AN-FO reacts exothermally with pyrite, and the reaction becomes self-sustained at 120° C ± 10° C. The Bureau of Mines has conducted an investigation to determine the reactivity of mixtures of AN-FO with pyrite containing ferrous sulfate. The results of tests in a heated vessel simulating a hot borehole demonstrate that small amounts of ferrous sulfate, a major product of pyrite weathering, initiate a self-sustained exothermic reaction with AN-FO at 80° C. Five pct by weight of urea was found sufficient to prevent a reaction among the three ingredients, at least within the limits of the test, which reached 180° C. Smaller amounts of urea and of potassium oxalate slowed down the reaction and delayed its onset to higher temperatures, but did not prevent it.

Jan 1, 1979

By Lucia Kuizon

Results of the U.S. Bureau of Mines' survey of mineral resources in the Cuyama RARE II study area indicate there is no potential for metallic minerals and low potential for the development of gypsum resources. There are no producing or developing mines within the study area. The Santa Barbara Canyon Prospect contains 30,000 tons (27,000 t) of subeconmic gyspum resources, the Wagon Road Prospect 276,000 tons (250,000 t), and the Brush Fence Canyon 61,000 tons (55,000 t). Most of the resource in the Brush Fence Canyon Prospect is outside the area. Gypsum was not observed at the Cuyama River deposit. Present gypsum and gypsite requirements are being met by larger deposits closer to major markets. INTRODUCTION Location (USGS) Present and Previous Studies (to be combined with USGS section) The Bureau of Mines reviewed literature and mining claim records for the study area. A field examination of known mineral properties was made in October 1980; it included mapping and sampling of prospects to evaluate the economic potential of mineral resources.

Jan 1, 1981

By Alton B. Cook

Data are presented to show oil vaporization resulting from the passage of natural gas through a sand-packed tube saturated with synthetic reservoir oils. The Bureau of Mines performed 13 experiments, using reservoir oils synthesized with base crude oils of approximately 22°, 35°, and 45° API, at 100°, 175°, or 250° F and 1,100, 2,600, or 4,100 psia. It has been determined that the amount of vaporization is significant if proper conditions exist. These experiments show that oil vaporization depends on pressure, temperature, volatility of the oil, and amount of gas cycled. Increases in each of these conditions increase the volume of oil vaporized.

Jan 1, 1969

By d&apos, Kathleen J. Amico

This summary appears in Minerals Year-book volumes I-II, and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The sections of this chapter and the area chapters in volume III contain further details on production. A summary table comparing world and U.S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operations at or near mines.

Jan 1, 1967

By Arthur M. Hartstein

The Bureau of Mines through contract with Ultrasystems, Inc., obtained gram per gram data of products formed on thermal oxidative degradation of selected compositions, both under dynamic and static conditions. Four broad classes of materials were studied! Polyvinyl chloride compositions, neoprene compositions, rigid urethane foams, and variously treated woods. Whenever possible, comparisons between pure components and composites were attempted. Thermogravimetric and differential thermal analyses were performed to gain understanding of the processes occurring and to explore the feasibility of using these analyses as a method of material identification. The toxic products detected and quantitated included HC1, H2S, CO, S02, CS2,COS, HCOOH, CH3COOH, formaldehyde, acrolein, C 6H6, chloroprene, chloroethanol, benzyl chloride, aniline, and furfural.

Jan 1, 1974

By Roy C. Bartholomae

An accurate characterization of the vibration environment and a vibration qualification test derived from it will be a very useful tool for manufacturers of instrumentation for use on underground coal mining equipment. Recognizing this, the Bureau of Mines sponsored a study wherein vibration levels were measured on mining equipment to form a basis for developing the required vibration test. The data base was composed of 160 samples taken at different positions on a variety of underground machinery. The data were analyzed and presented in a format typical of military vibration qualification tests. The form was shown to be virtually identical to the swept sine test envelope specified in MIL-STD-810B for tracked vehicles.

Jan 1, 1982

By Margaret R. Egan

The U.S. Bureau of Mines investigated the product-of-combustion (POC) characteristics of combustible materials used in typical coal mining operations in a series of experiments conducted in an intermediate-scale fire tunnel. The materials examined include wood cribs, transformer fluid, coal, conveyor belting, brattice cloth, and ventilation ducting. Smoke and toxic gases evolved from burning materials contribute to panic conditions and hinder escape. Smoke irritates and obscures vision, while toxic gases physically debilitate and disorient the victims. However, POC emissions may be used for early warning fire detection. POC levels will vary not only between materials but also between stages of combustion and the conditions in which they are burning. This report summarizes the POC characteristics of each material and evaluates their effectiveness for early warning mine fire detection. Results show that smoke was the POC most readily detected from the smoldering materials tested.

By John L. Hill

"The Bureau of Mines is conducting research on the causes and methods for control of cutter roof failure in underground coal mines. This hazardous ground control problem exposes miners to the danger of falling roof rock and frequently results in massive roof failure. This report outlines the probable causes of cutter roof failure, which are proposed based on field investigations, numerical model analysis, and in-mine observations. Traditional methods of control are presented, as well as innovative methods based on mining concepts developed during earlier years of coal mining history. The report can be useful to a mine operator for assessing the causes of cutter roof failure on a site-by-site basis and for predicting the probability of its occurrence. A process is presented for selecting an optimum control method that includes both traditional and innovative control techniques for each of the various causes of cutter roof failure. INTRODUCTIONGround control research conducted by the Bureau of Mines is designed to develop technology that will aid in reducing the frequency of accidents associated with poor ground control conditions. Cutter roof failure often poses a safety hazard to miners and causes delays in production while massive roof falls are cleaned up and unstable roof is resupported. Implementation of control measures reduces the threat of injury to miners and prevents production delays.The definition of cutter roof failure used in this report separates this unique type of failure from other ground control problems, to aid in the analysis of the causes and in the development of control methods. The definition is as follows:Cutter roof failure in mine roof rock is a failure process that initially begins as a fracture plane in the roof rock parallel to, and located at, the roof-rib intersection. The fracture propagates upward into the roof over the mine opening at an angle usually steeper than 60° from the horizontal.The mappable extent of cutter failure may range in length from only a few feet to several hundred feet and may traverse entry-crosscut intersections without change in direction. Once initiated along the roof-rib line, a cutter may propagate away from the roof-rib line of one side of a room, cross the roof span, and continue along the other side of the room. It is important to note that this definition excludes a similar type of failure (sometimes referred to as ""kink roof') that has comparable characteristics but occurs in the center of the entry. (The reasons for this distinction are discussed in the ""Background"" section.) Researchers refer to the cutter failure discussed in this report as ""classic"" cutter roof failure; except for short deviations across intersections and entries, initial failure is confined to the roof-rib intersection."

Jan 1, 1986

By Marvin L. Whisman

A radiotracer technique developed by the Bureau of Mines extends to the parts-per-billion range the sensitivity for determining contributors of deposits formed in stored and thermally stressed jet fuels. The method depends upon measuring radioactivity associated with thermally induced deposits from fuels containing one labeled compound. The technique was applied to 88 test blends, representing 12 fuels and nine carbon-l4 labeled fuel constituents or fuel additives, or both. Data from results of these tests are included in this report. With this radiotracer technique, the contribution of fuel components and additives to thermally induced deposits in a variety of fuel environments was estimated before and after storage.

Jan 1, 1969

By E. A. Johnson

As part of its effort to reduce the environmental impact associated with mining and metallurgical operations, the Bureau of Mines used a modified form of the Environmental Protection Agency's Extraction Procedure toxicity test on copper reverberatory slags that contained low, medium, and high levels of the impurity elements As, Pb, Sb, Bi, and Zn. All tests resulted in extracts that did not exceed those limits published in the May 19, 1980, Federal Register; there-fore, these solid wastes were designated as nonhazardous for most landfill disposal situations. However, arsenic and lead levels disturbingly close to the allowable limits--and even higher levels of copper and zinc, for which there are no established limits--leached from the high-impurity-element granulated slags. These slags should be handled in such a way so as to minimize the possibility of water contamination. One baghouse dust was tested according to the EPA procedure and found to exceed the extract limits by a factor of 10. This solid waste may be considered hazardous.

Jan 1, 1982

By Fun-Den Wang

A two-dimensional plane strain analysis by the stiffness matrix method was used to analyze two basic pit slope configurations. The magnitudes and the directions of stresses are given for a V-shape and for a flat-bottom pit with the slope angle varying from 30° to 90° at 10° intervals, Stress effects due to irregular pit configuration or to in-situ forces are discussed. Equations of similitude for gravity loading are given. Expressions are also given for the stresses at the toe as a function of slope angle. Procedures are given for finding the stresses in any geometrically similar pit slope of different dimensions and material properties from the stresses and equations presented in this report. Numerical results show that the V-shape pit slopes have lower stresses than the flat-bottom pit slopes; hence, they are inferred to be more stable.

Jan 1, 1970

By John C. Franklin

The Bureau of Mines conducted extensive laboratory and limited field tests to determine whether a polymeric material could effectively reduce the emanation rate of radon gas from uranium ore. In the laboratory 46 different single-coat materials and 14 two-coat applications were tested. The laboratory tests showed that up to 100 percent of the radon gas could be sealed into the rock. Materials tested in the laboratory were polyesters, furan resins, epoxies, latices, and totally inorganic coatings. From the laboratory work six different materials were selected for field testing. The first test was single-coat materials in five static chambers; the second test used two-coat applications in an open chamber. Both tests were conducted in the Dakota mine at Grants, N. Mex. During the second test, the amanation rate of radon gas was reduced up to 62 percent.

Jan 1, 1975