Search Documents

By C. R. Hopkins

"The petroleum refiners of the United States made rapid strides in fuel economy in 1928, when the calculated number of B. t. u. required to refine a barrel of crude petroleum was 637,000 as compared with 698,000 in 1927, a decline of 9 per cent. The major portion of this indicated increase in fuel efficiency was undoubtedly due to the gain in use of the pipe-still and the continuous process of refining as contrasted with the old batch method of distillation.,Almost without exception the new refineries are equipped with one or more pipe-stills, and many of the older plants are changing over to this type of equipment. The refineries of the Appalachian area are among the oldest and most conservative of the country, yet a number of them dismantled their old shell and cheese-box stills and installed pipe-stills in 1928.The more extensive use of the pipe-still was not the only way in which the refiners lowered their fuel requirements in 1928. The use of heat-exchangers, in which the heat from hot vapors to be condensed is used to heat the incoming cold oil, also increased in 1928, and in addition the refiners have kept abreast of the times in saving fuel through better insulation and improved burners.For the year 1928 the refiners burned as fuel the following: 46,400,000 barrels of-fuel oil; 3.362,000 short tons of coal; 114,950,000,000 cubic feet of natural gas; 77,313, 000,000 cubic feet of refinery or still gases; and 470,000 short tons of coke, in addition to a little electricity. This fuel was calculated to have produced a grand total of 582,156 billions of B. t. u., as compared with 578,784 billions B. t. u. in 1927.The total of 46,400,000 barrels of fuel oil burned represents an increase over 1927 of about 5,000,000 barrels, which made it about equal to the 1926 figure. Practically all of the refinery districts used more oil as fuel in 1928. The most important increase - over 2,000,000 barrels - occurred in the East Coast district, where greatly expanded throughput of foreign crude was instrumental in increasing fuel-oil production.The use of coal for fuel at refineries again registered a material decline, the total for 1928 of 3,362,000 short tons being 33 per cent below that of the previous year. The outstanding decrease in the use of coal in 1928 occurred in the East Coast district, where coal was probably replaced by oil. The use of coal for fuel at refineries in the States of Ohio, Pennsylvania, and West Virginia declined materially in 1928; the substitute used in the majority of cases was oil burned in pipe-stills."

Nov 1, 1929

By Lloyd A. Morley

This report abstracts project work performed under USBM Grant GO155003 during the period 4 November 1975 to 3 November 1976. The research was funded, as a continuance of previous support from USBM Grants GO133077 and G0155003, to gain further knowledge in mine electrical system safety. Five reports have been separately produced, all under the grant title, "Coal Mine Electrical System Evaluation," and are as follows: 1. Volume I - Continuous Monitoring, 2. Volume II - Transient Analysis, 3. Volume III - Shielded Cables, 4. Volume IV - Computer Modeling, and 5. Volume V - Battery and Battery-charging Safety. Abstracts of these comprise the balance of this document with one exception. The task ?d-c offsett currents," does not fall under the scope of the other report volumes and, further, the material to be presented does not justify a separate report. Hence, this subject concludes the Executive Summary.

Jan 1, 1977

By D. J. MacDonald

The Bureau of Mines investigated two alternative methods for treating a zirconium-bearing chloride-sulfate strip liquor to obtain reactor-grade Zr02. One method involves neutralization with NH3 and the other hydrothermal precipitation. The strip liquor was derived from zircon sand by a Bureau of Mines method for separating zirconium and hafnium via solvent extraction with a tertiary amine. Neutralization with NH3 to precipitate hydrous zirconium oxide required 0.9 to 1.1 g NH3 per gram of zirconium. The NH3 can be recovered for recycle. Zr02 that met reactor-grade specifications was produced by precipitation with NH3? Hydrothermal precipitation of Zr02 from strip liquor required that the solution be maintained at 2600 C and 680 psi for 10 min and in a non-corrodible pressure vessel. In bench-scale experiments both methods gave-zirconium recoveries greater than 99 pct.

Jan 1, 1984

By Adam K. Smith

Over-exposure to noise remains a widespread, serious health hazard in the U.S. mining industry despite 25 years of regulation. Most other categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. In order to reduce cases of Noise Induced Hearing Loss (NIHL) in the mining industry, retrofit acoustic treatments and controls are being developed to subdue noise at the source. The Mine Safety and Health Administration (MSHA) coal noise sample data collected from 2000 to 2005 has determined that continuous mining machines rank first among all mining equipment whose operators exceed 100% noise dosage. The continuous mining machine conveyor, used to move coal from the cutting face to the rear of the machine, has been identified as a dominant noise source. A dual sprocket conveyor chain was tested as a potential solution. Sound power level measurements conducted at the Pittsburgh Research Laboratory (PRL) accredited reverberation chamber showed a 3 dB reduction in the A-weighted sound power level when the dual sprocket chain was implemented. Underground results show an 8-hour Time Weighted Average (TWA8 hrs) reduction a 3 dB for continuous mining machine operators. Utilizing this newly developed noise control, along with previously proven controls, provides continuous mining machine operators an opportunity to be within the MSHA-Permissible Exposure Limit (MSHA-PEL).

Jan 1, 2009

By W. D. Bryson

This paper is one of a series being prepared by the United States Bureau of Mines on tunnel-driving methods. The practices described are those used at No. 11 mine of the Colony Coal Co., Denver, Colo. No. 11 Mine is situated at Dines, some 14 miles north of Rook Springs, in Sweetwater County, Wyo. It is served by a spur off the Winton branch of the Union Pacific Railroad. The Colony Coal Co.'s mines were opened in 1918, and since that time have been among the largest producers of coal for the railroad and domestic markets in the Rock Springs coal district.

Jan 1, 1932

Illinois has the largest reported bituminous coal resources of any state and is one of largest coal-producing states in the nation. Coal-bearing rocks underlie about 65 percent of Illinois, including all or part of 86 of its 102 counties. An estimated 18 1 billion tons of coal resources are still in the ground. Using present mining methods, more than 30 billion tons of coal are classified as recoverable. This represents almost one-eighth of the total recoverable reserves of all types of coal in the United States. The state's surface mining regulatory program was conditionally approved June 1,1982. It received full approval October 25,1988. The Abandoned Mine Land Program was approved June 1, 1982, and the AML emergency authority June 11, 1984.

Jan 1, 1992

By C. M. Bouton

Although much valuable work has been done in the study of dust explosions, the laboratory technique has not been developed to the point where the many factors involved can be properly controlled, and thus where really fundamental information can be obtained. This paper presents a brief discussion of the difficulties encountered in fundamental work on dust explosions, a description of apparatus intended, to overcome some of them, and an account of some results obtained. FACTORS INVOLVED IN DUST EXPLOSIONS The more important factors pertaining to the dust cloud itself which are known to determine the phenomena of explosions are (1) the kind of dust; (2) its fineness; (3) its concentration in the exploding cloud; and (4) the nature of the interior motions, or turbulence, of the cloud before and during the explosion. These factors are arranged in what seems to be an ascending order of complexity. The kind of dust is the factor most easily subject to control. The fineness of the dust at first sight seems to be a controllable factor, but when it is recalled [that] most explosible dusts are mixtures of particles of continuously varying sizes so small as to pass through the finest woven sieves, and therefore difficult to separate either for purposes of analysis or experiment, the fineness is seen to be a factor difficult to control accurately.

Jan 1, 1929

By David E. Van Dillen

This volume is a task-by-task review of work performed in modernizing the BMINES finite element code. Much of the discussion is accomplished by cross reference to the user?s guide, which is Volume I of this two-volume report. The computer program described in this report provides for the static, three-dimensional, linear and nonlinear analysis of structural and geologic systems by the finite element method. The nonlinear material properties currently available in the code include isotropic, anisotropic, variable modulus, plastic, viscoelastic, and viscoplastic. Load application capabilities include gravity loading, surface tractions, and initial stresses. The element library includes rods, beams, plane and axisymmetric quadrilateral elements, three-dimensional brick elements, thick shell elements, and plane, axisymmetric, and three-dimensional joint elements. Special features include the ability to simulate excavation and construction sequences by means of element activity. An automatic mesh generator is included in order to simplify input preparation.

Jan 1, 1981

By John Durkin

Owing to the daily exposures of uranium mining personnel to 222Rn daughters, a device is needed that will continually monitor individual exposure. Such a device has been built and tested by the Bureau of Mines and is known as a radon daughter dosimeter. This is an electronic instrument using a solid-state detector and circuitry. The concept of the instrument, which is a personal device worn throughout the working shift, is to evaluate an individual's cumulative exposure to airborne radon progeny, expressed in units of working level hours. Since the instrument is in close proximity to the miner and measures continual exposure, it avoids the errors caused by the present technique of spot checking of the environment and provides a more accurate account of total cumulative exposure.

Jan 1, 1977

By Valois R. Shea-Albin

An accurate assessment of the vertical stress on a coal seam at depth is important for mine design. Vertical stress calculation techniques presently available either are not sufficiently accurate or cannot handle complex surface topography. Therefore, the U.S. Bureau of Mines developed a computerized method to calculate vertical stress exerted on surfaces at depth that includes the effect of topography. Two input data sets are required: a digital elevation model containing topographic elevations and a coal seam file defining coal seam elevations at depth. Boussinesq's equation then quantifies the vertical stress resulting from topography. The computerized method was tested on a coal seam overlain by a complex topography where a vertical stress map encompassing several square miles was produced. Results show that depth mitigates the affects of surface topography, while the coal seam topography has a direct effect on the vertical stress. In comparison to the computerized method, the direct stress method overestimates stress under hills and underestimates stress under valleys. The largest difference between the two methods occurs under the steepest topographic relief. A limitation of the computerized method is that stresses cannot be accurately determined near an outcrop.

Jan 1, 2010

By N. E. Hanna

An important goal in the development of coal mining explosives has been to improve their safety characteristics through suitable formulation. In the United States no systematic effort to establish factors influencing the incendivity to firedamp and to coal dust of explosives through research was made until the last decade. In consequence, American permissible explosives underwent only very slight modifications and many remained substantially the same as in the early years. As part of a long range program for increasing the safety of permissible explosives, the Bureau of Mines undertook to determine how the amounts and particle sizes of the principal constituents of these explosives affect their incendivity. It was found that an increase in the relative amount of sodium chloride and a decrease in its particle size significantly decreased the incendivity of our permissible explosives to firedamp (7-9).6 This is in agreement with findings reported by Dolan (4) for compositions of nitroglycerin and salt. One important result of the work at the Bruceton station has been the recent introduction of salt-formulated permissibles by several explosives manufacturers. This paper describes a statistically designed experiment for studying the effects of the particle size of ammonium nitrate and the type of carbonaceous materials used on the incendivity of permissible explosives. Interest in these particular effects goes back as far as the first formulations of coal mine explosives, around 1910 in the United States and even earlier in Great Britain and other countries. Although it is well established that fine

Jan 1, 1961

By John A. Davis, John Gross

This paper is one of a series giving the results of metallurgical tests conducted by: the Alaska station of the Federal Bureau of Iſines, on the recovery of gold from the black sands of placer clean-ups. The data given in this report were obtained from tests on a lot of black sand from a property located on St. Patrick Creek, Fairbanks mining district, Territory of Alaska. This property comprises the Sagan Fraction and adjoining bench claims, and is being operated by J. A. Lillie. The sand ad already been treated at the mine by amalgamation. A sample taken by Mr. Lillie and assayed at the station showed that the gold still remain ing amounted to ll cents per pound. As this gold content was sufficiently high to justify further treatment of the same, 770 pounds were shipped to the station for testing. The reader will note that the gold content is given in cents per pouni, rather than per ton. This is in conformity with practice in the district in valuing black sands, as the quantity obtained at any one time is small, much less than one ton. . The sand consisted principally of schist and quartz, with very little ilmenite and garnet; and no magnetite or sulphides. Most of the gold present as contaminated with quartz, as the free particles of gold had been removed by amalgamation at the mine.

Sep 1, 1920

By E. D. Gardner

Humphreys Gold Corporation of Denver, Colo., was conducting a successful placer operation in 1936 on North Clear Creek about 6 miles below Blackhawk in Gilpin County, Colo. About 3,000 cubic yards of gold-bearing gravel are dug daily (September. 1936) by two draglines and a power shovel. The gravel is screened in a portable washing plant; the trommel oversize is discarded, and the undersize is pumped to a gold-saving plant. The gold is caught in riffles in sluice boxes. The total cost of mining is about 20 cents per cubic yard. The mine is in a narrow canyon at an altitude of 7,200 feet. The Blackhawk-Central City branch of the Colorado & Southern RR. runs over the property. Freight platforms for receiving supplies were moved as the workings advanced. The workmen reached the mine on a speeder that ran on the railroad tracks from a point on the automobile highway (U. S. 40) on Clear Creek near the bottom of Floyd Hill, about 5 miles distant. The mine is 36 miles by road and speeder, or 30 miles by rail, from Denver.

Jan 1, 1937

By Ralph L. Windrow

This paper is one of a series being prepared for and published by the United States Bureau of Mines describing methods and costs of mining and preparing sand and gravel for market at various plants throughout the United States. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. The Clowdy plant, with which this paper deals, is located 7 miles west of Dallas, Tex., and has a rail connection with the Texas and Pacific Railway. In addition to the rail outlet there is a paved road over which materials produced at this plant can be moved into Dallas by truck.

Jan 1, 1932

By Oliver W. Keener

The operation described herein differs from the usual practice in the Tri-State district in two important respects: (1) the ore is loaded into cars which are tramped to the shaft and hoisted on self-dumping cages, and (2) about 30 per cent of the ore is loaded by power shovels. The four-month period covered by the cost data appended at the end of the paper immediately followed a period of about one year during which the mine was shut down, and the expense incident to the resumption of operations is reflected in the costs. The author acknowledges the assistance of C. F. Jackson, mining engineer, U. S. Bureau of Mines, in the preparation of this paper and the compilation of the data.

Jan 1, 1929

By Spencer P. Hwell, Charles E. Munroe

"Among the surplus explosives left on band with the War Department was a quantity of that styled Trojan Grenade Powder, which was especially designed during the war for use as a bursting charge in grenades and for which naturally there would be very little military use in time of peace. With a view to its disposal through use in civil projects a quantity was sent to the Bureau of Minas explosives experiment station, where analysis showed that its characteristic explosive ingredient was nitrostarcn and that the powder bad the following composition:Trojan Grenade Powder appears as a dark gray granular substance, part of which is slightly pulverulent. The granules fairly hard. The explosive is not at all dusty, and has the consistency of granulated sugar.Nitrostarch is a substance produced by treating starch with nitric and sulphuric acids and in appearance it looks very little different from powdered starch. It resembles nitrocellulose and nitroglycerin in its constitution and explosive properties and has been longer known than either, it having been prepared by Braconnet in 1833. Nitrostarch explosives have in recent years been developed for industrial use in this country, they having been used to an extent in blasting in the Canal Zone, yet as this grenade powder was a special composition it seemed desirable that a complete series of tests should be run upon it. This was done, and the results are reported in the following table in comparison with those previously obtained in testing ammonia dynamite."

Jun 1, 1920

By C. E. Jordan

The Bureau of Mines conducted laboratory studies on methods to increase the recovery of brine from slime produced by operating potash plants. The slime was comprised of 80 percent brine saturated with KCl and NaCl, and 20 percent solids. A variety of settling techniques, filtration methods, continuous centrifugation, and novel processing techniques were investigated. Vacuum filtration recovered 6S percent of the brine at 47 gallons of brine per square foot per day. Pressure filtration, on the other hand, recovered 74 percent of the brine at 40.9 gallons of brine per square foot per day. Centrifugation in a 6-inch-diameter continuous decanter-type separator resulted in 42 percent recovery of the brine at a treatment rate of 542 gallons of brine per day. Vertical drains proved to be the most promising novel debrining technique investigated. With this method, 45 percent of the brine was recovered in 3 days.

Jan 1, 1977

By J. B. Gayle

Numerous investigators have studied the addition of inert4 substances to coking blends. Generally, the results have yielded trends applicable only to the particular coals and inerts studied. Recently, somewhat more general results were obtained for cokes produced from blends containing added inerts, using the sole-heated oven. The present investigation represents an extension of this work to include a wider range of inerts and to determine the applicability of the various conclusions to cokes produced with the Tuscaloosa oven. The results indicated that an increase in dry-coal charge density of 1 pound per cubic foot (p.c.f.) caused a corresponding change in the hardness (1/4-inch tumbler index) of Tuscaloosa oven cokes of 0.9 percentage points. This value compares favorably with the value of 0.7 determined previously for the sole-heated oven and Bureau of Mines-American Gas Association (BM-AGA) retort.

Jan 1, 1961

By L. B. Pankratz

Heat contents were measured for Na2CaSi04 and Na2Ca2S02 between 298° and 1,300° K, for Na2Ca2Si309 between 298° and 1,500° K, and for Na4CaSi3O9 between 298° and 1,350° K. Copper-block drop calorimetry was employed. Reversible, first-order transitions were found for Na2CaSi04 and Na2Ca2Si309. The transition for Na2CaSi04 is at 830° K with a heat absorption of 160 cal/mole; that for Na2CagSi309 occurs at 750° K with a heat absorption of 1,550 cal/mole. Results for the other two silicates showed no irregularities. A table of heat content and entropy increments above 298.15° K and heat con-tent equations are included for use in thermodynamic calculations.

Jan 1, 1968

By E. R. Cole

A lead smelting process that appears to present minimal pollution problems has been developed at the Bureau of Mines, Rolla Metallurgy Research Center. Ten and 100 g samples of PbS mill concentrates were vaporized at 1,000° to 1,100° C in a furnace with an inert gas atmosphere during a 2-hour period. The PbS vapor was transported by the inert carrier gas to the reduction zone of the furnace where it was reduced at the same temperature with excess hydrogen to metallic lead. Lead of 99.9 pct purity was produced. The H2S formed can be decomposed into elemental sulfur and water vapor by a modified Claus process. Approximately 90 pet of the Cu and 70 pct of the Ag and Zn remain in the residue and are potentially recoverable. More than 98 pct of the lead in the concentrates was extracted.

Jan 1, 1974