Search Documents

By L. J. Douglas, A. G. Kim

Methane and other hydrocarbon gases, byproducts of coalification, are emitted from coal at widely varying rates and often present ventilation problems during mining. The air in some coal mines apparently contains no methane. To determine if coals from mines which had no history of detectable gas emission contained adsorbed methane, samples of coal at the shaft bottom and at an active face were obtained and placed in sealed metal cylinders. The atmosphere around the coal was sampled and analysed by gas chromatography. Methane, ethane, ethylene, propane, propylene, and butane were found to have been desorbed from these coals. Hydrogen and helium were also detected. An estimate of the amount of residual gas per ton of coal indicated that coal samples from the active face generally contained more adsorbed gas than coal samples obtained from the shaft bottom, although in both instances the total amount of gas was relatively small.

Jan 1, 1973

By James R. Aggson

The theoretical relationships that are used to calculate in situ rock stress magnitudes and directions from borehole deformation data obtained during overcoring are based on the assumption that the rock is a linearly elastic material. Strictly speaking, this assumption is not valid in any rock. Thus, investigators using overcoring techniques must either accept various degrees of nonlinearity and the associated inaccuracies or use core testing techniques that address the problem and compensate for elastic nonlinearity. Previously developed test procedures for stress-relief overcores partially correct for nonlinearity. This Bureau of Mines paper describes a test procedure that completely corrects for elastic nonlinearity in stress-relief overcores.

Jan 1, 1977

By Thomas J. Peters

The U.S. Bureau of Mines studied the 63,9SS-acre Hanson Lakes study area, including the Ten Mile-East and part of the Ten-Mile West RARE II areas, plus additional acreage, all proposed at times for Wilderness designation. The study was part of a Idaho Land Assessment Program with the Idaho Geological Survey and the U.S. Geological Survey, to provide minerals information for land-use decisions, and ensure domestic mineral supplies. The area is at the north end of the rugged Sawtooth Range and includes parts of the Sawtooth National Recreation Area which is closed to mineral location. The Copper Mountain. Elk Mountain, and Observation Peak mineralized areas are in the study area, but only Copper Mountain is open to claim location. It is on the trans-Challis fault zone and contains Tertiary granite which is favorable for mineral deposits of gold, beryllium, niobium, REE (rare-earth elements), tin, molybdenum, copper, silver, and lead. Identified resources are 1.9 million tons of flake graphite at Elk Mountain, but much more graphite occurs in the vicinity REE occurs in 18 black sand placer sites along the lower reaches of study area streams just outside the study area, on Cape Horn Creek, Marsh Creek, and lower Valley Creek flood plains, and at one hydrothermal site near Observation Peak. Hydrothermal REE is commonly low in? by-product thorium. a radioactive disposal problem. Many advanced REE applications enhance the quality of life, and future uses in superconductivity may reduce energy consumption. Seventeen lode, one geothermal, and 11 placer prospects were examined. Workings totaled about 20 adits, one shaft, several open cuts, and numerous small pits. Approximately 500 mining claims have been located or relocated in the study area, including a 200-claim block for disseminated molybdenum.

Jan 1, 1992

By James J. Olson

The Bureau of Mines recorded and analyzed overpressure levels for three production blasts at the White Pine copper mine, Upper Michigan, to obtain representative data from single-heading blasts in a long, straight haulageway and to estimate the damage potential inherent in production blasts fired in close proximity to underground structures. Commercial pressure gages with a flat response to 1 kHz were used with an FM tape recorder to record the overpressures from one dynamite and two AN-FO (ammonium nitrate-fuel oil), 500-msec production blasts having zero-delay charge weights of about 75 lb (34 kg). The recorded waveforms from the underground blasts (1) were more complex than the typical free-air wave, (2) were of longer duration, and (3) had numerous secondary arrivals due to reflections from the ribs and roof. The waveforms showed that the zero-delay charges produced the only high overpressures. First pulse peak overpressures from the blasts ranged from 0.10 lb/in2 (6.9 X 102 N/m2) at a distance of 471.1 ft (144 m) to a maximum of 1.76 lb/in2 (121.3 X 102 N/m2) at 191,7 ft (58.4m) from the blasts. An analysis of variance of the first pulse overpressures from the three White Pine blasts showed that no statistically significant difference existed among the overpressure levels from the dynamite and AN-FO blasts and that a single equation P = 4.9 x 103 (D /W1 / 3) 2 .15, where P = overpressure in pounds/inch2, D = d-stance from the blast in feet, and W = zero-delay charge weight in pounds, could be used to describe the falloff of overpressure with distance.

Jan 1, 1971

By Raymond B. Ladoo

Talc mining ·in the state of New York was first started about 1876, but important production did not start until 1880, when about 4,000 tons were shipped, In 1883 the production was about 6,000 tons valued at $75,000, or an average of $12.50 per ton, From this date the production gradually inc~eased to a peak of 93,236 tons in 1916, valued at $961,510 or about $10,30 per ton, In 1918 the production declined to 71,167 tons valued at $902,100, or about $12,70 per ton. For ma.ey years New York ,-Jas the largest producer in the United states, but in 1917 and 1918 its output was surpassed by Vennont in tonnage thou[;h not in value. In June, 1920, there were three companies producing talc in the Gouverneur district, st. La,1Tence Co'Ul'lty, and one near Natural Bridge.

Oct 1, 1920

Provide better ventilation for mines by reducing air leakage around stoppings. Approach Most stoppings are constructed of concrete blocks and trowelled-on mortar and are not very airtight. Bureau of Mines research has shown that brushing on modified mortar containing fiberglass and/or other additives, that enhance strength and adhesion, minimizes air leakage around and through the stoppings. Airtightness is an important factor in building stoppings since an airtight stopping will provide for more efficient ventilation airflow and more cost-efficient use of the mine's ventilation system. How the New Technique Works After broken floor and rib material is removed, the stop-ping faces are covered with one or two coats of modified

Jan 1, 1982

Provide a rapid, reliable means of warning underground miners of a fire or other emergency. Approach An ultalow-frequency electromagnetic signaling system was designed, breadboarded, and tested at various under around mines. How It Works Current fire warning systems for underground mines, such as stench, audible alarms, and messengers, arc slow, unreliable, and seldom achieve total mine coverage. An ultralow-frequency electromagnetic fire warning alarm system with true through-the-earth signaling capabilities was developed to solve these problems. The system was originally designed for high-back room-and-pillar mines where stench systems are unusable due to the low velocity of mine air flow. However, the system has an application to all underground mines.

Jan 1, 1988

By William A. Beck

The K.T. Dome Mine in Owen and Henry Counties, Ky., has been operated intermittently under several different owners since the early nineteen hundreds. No record of total production is available, but it is said that during 1943 and 1944, while being operated by the Twin Valley Mining Co., 30 cars of zinc concentrates and 10 cars of lead concentrates were shipped. The vein can be traced for about 10 miles along the strike from Lockport, Henry County, to Big Twin Creek in Owen County. It pinches and swells both vertically and horizontally and is reported to average 20 inches in width. In order to develop additional reserves on the property, the Bureau of Mines drilled four holes on the south extension of the vein. Drilling disclosed that the vein dips to the west on the south side of the Kentucky River and is continuous along the strike and in depth. However, the extent of mineralization in the vein varies widely.

Jan 1, 1949

By J. H. Weber

This Bureau of Mines publication describes the hardware system and software package for the semiautomatic acquisition and automatic processing of high-resolution mass spectrographic plates. The semiautomatic data acquisition allows a tenfold saving of time compared with manual data acquisition. Automatic processing of the high-resolution data to yield exact masses, intensity, and the corresponding empirical formulas is accomplished by efficient programming on a small, inexpensive, programmable calculator system.

Jan 1, 1974

By R. Hogg, T. F. Dumm, L. G. Austin, M. Yekeler

"Dedicated to Professor Kurt Leschonski on the occasion of his 60th birthdayAbstractThe kinetics of batch grinding quartz from a feed of 600 by 425 Jim to a product of 80% less than 10 µm have been determined using screening and laser diffractometer sizing for size analysis. The specific rates of breakage decreased by a factor of about three when the material became less than about 100 µm in size, but the primary breakage distribution function also changed to give proponionately more fine material, so that the grinding efficiency expressed as the development of surface area (B.E:T.) per unit of energy input did not decrease. Analysis of the shape of the particles in the 2S x 38 µm size range showed that particles of this size produced by roll crushing or by 8 minutes of grinding of a 42S x 600 µm feed were not different but at long grinding times the particles were rounded. This suggests that the breakage mechanism changes to give more chipping and abrasion and less disintegrative fracture. As the material approached the ultrafine size range it adhered to the mill case and there was no further size reduction. However, a technique for striking the mill case to dislodge the particles was successful in allowing further grinding to 400Jo by weight less than 2 µm.1 IntroductionIt has long been known that it is difficult to accomplish ultrafme grinding in a tumbling ball mill. It has been reported [12, 13] that there is no further size reduction after some hours of grinding cement clinker in laboratory ball mills. Austin and Bagga (1] and Shah and Austin [16] have given an analysis of the kinetics of dry grinding in a laboratory ball mill, introducing the concept of a slowing-down factor K, which is the ratio of the specific rates of breakage at some long time of grinding to the normal specific rates of breakage. They showed that this factor decreased as fine material accumulated in the mill charge. Cottaar and co-workers [8-10] showed that the movement of solid in a dry laboratory ball mill was influenced by the fineness of the solid and by the presence of air, and that evacuation of air from the mill caused particle sedimentation and low rates of breakage.The concept of the slowing-down factor has also been used in wet grinding [17, 18]. At very .high slurry concentrations it appears to be correlated with a steady decrease of mill power caused by the build up of a layer of deposit sticking to the mill case. This reduces the effective mill diameter and, eventually, the balls start to adhere in the layer and centrifuge. A decrease of mill power always indicates less lifting and tumbling of the media and, hence, less breakage. However, slowing-down of breakage rates was also observed at lower slurry concentrations where there was no change in mill power."

Jan 1, 1990

By John Taber, Robert D. O'Brien

"INTRODUCTION The Bozeman corundum deposit was first examined in May 1944 by an engineer of the Bureau of Mines. In August 1944, the property was re-examined because of a sharply increased war demand for corundum. A small program of trench exploring was undertaken after the second examination. The work was started in October 1944 and was completed in December 1944. This report presents the essential data obtained by the exploratory work.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that, they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploration work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests.The field work on the Bear Trap project was supervised by E. W. Newman, district engineer Montana District office. The microscopic examinations and. the grid grain-count analyses of the samples and the beneficiation tests were made at the Bureau's laboratory at Salt Lake City, Utah, under the direction of S. R. Zimmerley, chief, Salt Lake City Division, Metallurgical Branch."

May 1, 1947

By F. E. Block

This investigation was made as part of a larger program to develop basically new methods for preparing yttrium metal in high-purity form. It was performed under a cooperative agreement between the U.S. Atomic Energy Commission (AEC) and the Federal Bureau of Mines. Laboratory-scale tests were made to devise methods for preparing high-purity, anhydrous yttrium trichloride, for reducing the yttrium trichloride with sodium or lithium, and for consolidating the resulting yttrium sponge into ingots.

Jan 1, 1960

By A. L. Engel

This publication describes further research by the Federal Bureau of Mines in beneficiating domestic manganese ores. The ores selected for treatment were typical of many manganese deposits in California and Nevada in that they have not been economical to mine because they are low grade or contaminated with siliceous minerals and are not amenable to physical concentration.3 4/ It would be desirable to develop a simple treatment method resulting in nearly complete extraction of manganese from these ores and applicable to small-scale operations. Sulfation reduction appeared to be such a method. The studies reported in this publication were directed toward sawdust or lignin-sulfonates as reducing agents. Sawdust, as waste from lumbering, and lignin-sulfonates, byproducts of woodpulp papermaking, are comparatively cheap and may be available in areas where manganese ores are found. Sugar, oils, and coal were also tried as reducing agents.

Jan 1, 1960

By W. H. King

"INTRODUCTION The manganese deposits of the Drum Mountain area were investigated as two separate projects. The first was begun in November 1940 and completed in August 1941, and the second began in January 1945 and ended in May of the same year. The first project was initiated as part of the Bureau of Mines program for development of strategic minerals for national defense. Subsequent operations disclosed conditions somewhat different than were expected, and it was decided that additional drilling should be done to delimit the ore bearing horizons further.The more promising manganese deposits in the Drum Mountains are situated on properties known as the Staats manganese mine and the Pratt manganese mine. The property controlled by the Pratt interests is under lease to the Ward Leasing Co. The 1941 project investigated the deposits on both properties, whereas the 1945 project was planned to explore further the oxidized ore bodies of the Pratt mine, although one hole was drilled in an attempt to extend the carbonate ore body on the Staats property (fig. 1).ACKNOWLEDGMENTSIn its program exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests."

Jan 1, 1947

By W. C. Hudson

"The McLeod sand pits, on the northeast side of the Little Ocmulgee River in Wheeler County, Ga., opposite Lumber City in Telfair Co., were examined by the Bureau of Mines under its war program of Investigation of Critical and Essential Minerals. The pits are about a quarter of a mile above the bridge, which is half a mile above Lumber City. Mrs. A. T. McLeod of Lumber City owns the land, including the pits. The property was inspected by an engineer of the Bureau of nines on March 8, 1945, on recommendation of Capt. Garland Peyton, director, Division of nines, Mining, and Geology of Georgia.The Mcleod pits are at the northwestern extremity of a mile-long series of old pits that were worked from about 1900 until the 1920's. The burning of the spur railroad bridge connecting the pits with the Southern Railway at Lumber City stopped mining operations. The pits on the south-east, or opposite, side of the Glennwood Road from the McLeod pits were first worked by F. L. Hinson and later, in 1921, by Mrs. n. H. Mobley. The glass sand was shipped to Tallapoosa, Ga., and Chattanooga, Tenn., where it was used in the manufacture of bottles for soft drinks. Some of the sand was used as molding and construction material. The sand was mined by hand shoveling it into wheelbarrows, which were unloaded on freight cars. The pits were partly refilled with overburden, so that it is impossible to estimate even roughly the amount of sand excavated.Analyses of samples of glass sand made years age3/ and later in 19404/ roughly check those made by the Bureau of Mines laboratory, except that in the former the iron oxide content usually was greater, attaining a maximum of 0.72 percent.The sand pits are in a valley slightly more than a quarter of a mile wide that lies along the northeast side of the Little Ocmulgee River. The land is either flat or marked by ridges only a few feet high. . A rather thick growth of scrub trees covers most of the valley. The surrounding country consists of gently rolling farm lands. The altitude of the valley is not known, but, judging by its distance from the seashore, it probably is about 200 feet. In addition to the Glennwood highway, which crosses the valley, several old sand roads lead to the pits."

Apr 1, 1946

By J. E. Tiffany

"The new permissible blasting device, Cardox, utilizes as a blasting agent liquid carbon dioxide which is discharged.as a gas from a steel container or shell. The loaded shell is placed in a borehole, stemmed, and tamped in a manner similar to that employed with explosives, and is fired by electricity.The Bureau of Mines' approval for use of the device in coal mines was granted as Approval No. 1 under date of October 3, 1928; as the result of tests made under the conditions and requirements of Schedule 20. There have been three subsequent extensions whereby minor modifications in the original design were granted.The permissibility of the device is subject to the following conditions; (1) It shall be in all respects similar to the sample submitted for tests; (2) certain thicknesses of disc and. weights of heater ingredient and of carbon dioxide, all of which are set forth in Table 2 under the provisions governing permissibility, must be used: (3) the rear cap must always be in place after the shell has been charged, to prevent accidental firing; and (4) firing must be done by means of a permissible-type blasting unit.The permissibility of Cardox was established by gallery tests similar to those used in testing explosives for permissibility. In these tests the shell was discharged into gallery 1 without causing any ignition of gas and air or of gas, dust, and air mixtures there. The conditions of charging the shell, such as weight of the ingredients of the heater element, the carbon dioxide charge, and thicknesses of the disc, were varied according to the conditions under which it would be likely to be used in blasting. The tests made in gallery 1 are here described in detail, as are also the tests which have been made for determining the propulsive strength of the device and the quantities of poisonous gases given off when a shell is discharged."

Mar 1, 1929

By A. B. Hooker, J. W. Paul

"There was a time when any suggestion that the Davy flame (safety) lamp be discarded, would have evoked unlimited, criticism. However, that time is past.Investigations both here and abroad have shown conclusively that the Davy lamp does not have the necessary factor of safety against ignitions of mine gas, and England, the lost stronghold of the Davy lamp in Europe, has eliminated this lamp and substituted safer types.In the United States there are companies who still use the Davy lamp in spite of all that has been said and published as to the dangers connected with its use.Recently the purchasing agent of an anthracite coal company requested the Department of the Interior, Bureau of Mines, to pass upon the safety of some braise gauzes for use in a shielded Davy lamp. A shielded Davy lamp is an ordinary Davy safety lamp equipped with a circular brass shield that is attached to the lamp posts. This shield extends about one-half way around the gauze and one-half of the gauze height. The main purpose of the shield is to prevent the lamps being extinguished by a sudden increase in the velocity of the air current past the lamp.The brass gauzes submitted for this test represented two grades of brass - a yellow brass and a red brass. The analysis of these brasses was not determined. Two shielded Davy lamps that were submitted for the tests each had a steel gauze. These steel gauzes were also tested. Tests were made in horizontally moving mixtures of Pittsburgh natural gas and air at velocities of 400 to 1,000 feet per minute. The gas percentages used were 7%, 8.6%, and 11%. Tests were made with the lamp shield in two positions relative to the lamp and direction of flow of the gas-and-air mixture. In one position the shield was between the gauze and flow, as normally used. In the other position the shield was on the downstream side of the lamp. The tests were continued until one or more failures or gas explosions been obtained with each of the six gauzes. The results of these tests summarized as follows:"

Jun 1, 1923

By W. Hermanson

This report, which covers the period from January 16 to October 21, 1974, describes the work performed in compliance with the requirements of contract no. H0242028 and modifications 1 and 2 thereto. The purpose of the contract was to further reline and modify three of the canopies (shuttle car, loader, and roof drill) which were developed under contract no. H0220031, and to conduct further testing and demonstration of the relined designs. Modifications I and 2 involved conducting further in-mine evaluations of the face. drill and cutter canopies, also developed under contract no. H0220031. In addition to the canopy modifications, the contract involved an evaluation of an operator's seat concept for a shuttle car which was developed for the USBM by another contractor.

Jan 1, 1974

By A. B. Hooker, L. C. IlsLey

In lare-scal e blasting, it is customary to fire me.l'\Y shot.!:l simu1. taneously. The electric !atonators ara usually conneced in seies, ard are fired either from a power circuit or :from a blasting ma.chine with large capacity, operated by hand. "!hen :'::ri111; with a blasting ca.chine, trouble with missed shots has been freqi.,.ently e>:pert0nced.. Unit1:i:' thes ,:::rcu:ns tances, the shots that fail to fire are often a gr"up in the t.:E"nter r,f t>e series, Various explaz,.a.tions hs.ve been given as to the cause of the failurs. Tis paper covers a few tests made cy the electrical section of tl:.e Dti..'t'cau. cf Mines, wh;.r.;h may be helpful in understanding the -probable cuse of tl1e misfiring of c.:anter shots, Wh3tever th9 source ot the firir. current generator, magneto, or batter, the CUl"rent delivered th:·01.1.gh a shot-f:?·ing circu.it is determined by t.ae total resistance of ,;he clrcili +.; c:1nd all cure:it leaving th9 p,si tive terminal must return to tre negative te1-minal. If a. metallic circuit is well i1,.sul.:tted, praeti­ccl. l;1 a.ll of the t.'Urrent keepo within the circu.it; but in a. shot-!11·.irig ci.rc1li t, Nhere the ·.vires f:ll·e often 1n c.c,i.cact with the eru:"!ih as i11 wet holer., end whero the ins".lla.tion of the leg wires :i. inadecpa.te to prc·,ent lea.l.tage, the current ma.v tu.e v a.r ious pa the: thro-.. .. gh the nr r. earth.

Aug 1, 1922

By Peter Kovalchik, Ed Kwait, T. Michael Durr

1. BACKGROUND Many research projects on engineering controls for noise reduction in mining were conducted by the former U.S. Bureau of Mines, mostly under contracts from 1972 through 1986.1 Contracts were awarded to determine which mining equipment was responsible for worker noise exposure over the permitted Federal Regulation level of 90 dBA for 8 hours. Dominate noise sources, for each piece of equipment was also determined. The final goal was to develop engineering noise controls for those pieces of equipment and then evaluate them. This was the general approach taken in each research project or contract. This paper deals with what is known about the control of noise from continuous miners, one of the most commonly used underground mining machines. A literature review on continuous miners revealed that the relevant noise sources were divided into four categories: conveyor, cutting head, drive train, and motor noise. The dominate noise sources reported were the conveyor noise and the cutting noise.2 Conveyor noise consists of impacts and scraping at various locations on the conveyor structure. These impacts are associated with discontinuities on the top and bottom decks, impacts between the chain and the tail roller, impacts on the sidewalls at path points of discontinuity under horizontal pivot, and impacts on the flex plate.3 Scraping occurs along the entire length of the chain conveyor. The other dominate source, the cutting of coal, has also been addressed in past research.4, 5, 6 The research presented in this paper only addresses the controls associated with the conveyor. The literature suggests several effective treatments for noise control: retrofitting the chain conveyor with a urethane coating or a urethane sleeve on the chain flights, using a urethane coating or urethane sleeve on the tail roller, constrained layer damping of the decks, and the use of a modified take up plate.7, 8 However, the in-mine durability of these concepts has yet to be proven for the conveyor system. This paper analyzes extensive noise and urethane durability testing on a Joy 14CM9 continuous miner’s conveyor assembly, tail roller, and bottom plate conducted at the Pittsburgh Research Lab facilities. It will also discuss the initial underground testing results for the urethane-coated conveyor flights and tail roller.