Search Documents

The method of using large-diameter augers to recover coal was introduced to the mining industry about the end of World War II, and production of bituminous coal with augers has increased steadily to an estimated 7 million tons, or approximately 1.4 percent of the total mined in 1956. Although auger mining has proved to be a reliable and economical method of mining coal, a number of unfortunate fatal accidents have been experienced; consequently the need for these recommended safety standards is indicated for this comparatively new method of coal mining. As mining methods and equipment change from time to time and new hazards are introduced, these standards will be revised; therefore, questions or suggestions from the coal-mining industry will be welcomed and carefully considered.

Jan 1, 1958

By Richard F. Hewlett

Use of digital computers makes possible a more efficient and complete analysis of data from a mineral deposit . This computer program was written and used during an investigation into the efficiency of methods of computing grade and tonnage of ore , wherein it was necessary to make repeated computations involving different combinations of data . This investigation was part of a continuing program of sampling methods research at the Bureau's Denver Mining Research Center.2-4 This program is designed to compute tonnage and average grade for 40 cutoff grades using either the statistical or polygonal methods . tational rate is from 200 ( input bound ) to 1,400 assays per minute , depending on the use of either individual ( one assay per card ) assay- interval length or

Jan 1, 1963

By William H. Schiffbauer, Ph. D. Mowrey

Proximity warning devices can improve workplace safety by alerting workers when they are in a hazardous area near moving equipment. Industrial work sites often present extreme challenges to safety-based proximity warning devices. Many commercially available types of proximity warning sensors and systems can be rendered useless when covered with mud, ice, snow, ore, rock, and other material. The list includes radar, ultrasonic, capacitive, and visual types of sensors and systems. Addressing these shortcomings, NIOSH personnel have developed a patented active proximity warning system called HASARD (Hazardous Area Signaling and Ranging Device) which employs lowfrequency, low-power magnetic fields which are quite impervious to severe environmental conditions. A shapeable wire loop antenna which provides the marker of dangerous work areas, has been mounted on a continuous mining machine and was mounted inside 1.3-cm thick angle iron. This loop antenna was exposed to more than six months of active underground coal production, which included being covered by and scraped over with tons of rock, sprayed by a continuous stream of water, and immersed in thick mud. After six months the loop antenna showed signs of wear, but was still capable of performing its intended function. The HASARD system is now being applied to other industrial applications and is showing much promise, especially in harsh environments. This paper details the system, describes the tests that have been done, and mentions other areas where it can benefit the safety of industrial workers.

By F. S. Crawford

Interesting data on electric blasting and sinking of the Montreal No. 5 shaft of the Montreal Mining Co., Montreal, Wis., were obtained during the sinking of the last 877 feet of this shaft. Several unusual features and safety practices are also to be found in the Montreal mine. The Montreal shaft was sunk 2,156 feet from August 16, 1921, to May 1, 1924, and 877 feet from October, 1927, to June, 1928. The first section of the shaft was supported with steel sets spaced 5 feet on centers; and instead of lagging the walls were covered with three-eighths of an inch of gunite where Greenstone was encountered, and where quartz-slate was found (from the surface to the 12th level) the walls were lagged with tamarack lath treated with carbolineum, a preservative.

Jan 1, 1929

By B. W. Gandrud

In 1927 Coghill5 showed that there is considerable liberation of the iron oxide mineral from gangue when the Alabama red iron ores are ground to a size suitable for classification and tabling, but that there is not sufficient to make possible a high extraction and a high grade of concentrate. Coghill states: High extraction and high grade of concentrate cannot be obtained without grinding to a size comparable with flotation or cyanide practice. If grade of concentrate be sacrificed the grinding need not be so severe.

Jan 1, 1934

By A. C. Johnson

The Ellington manganese deposit in Reynolds County J Mo., had been known for some time; and limited exploration, consisting of test pitting and sinking a shaft 54 feet deep on the property, had been done by private interests. Late in 1941, the Bureau of Mines cleaned, deepened, and sampled many of the existing pits and dug and sampled 27 new ones. The shaft was unwatered and sampled, and several pockets of manganese ore were trenched to determine their extent. Samples were analyzed and beneficiation tests on 1 ton of the ore were made at the Rolla, Mo., station of the Bureau of 'Mines. Results of the investigation indicated that the deposit was small and low in manganese content.

Jan 1, 1948

By B. W. Madsen

Research by the Bureau of Mines has shown that treatment of open pit waste by crushing and sizing followed by flotation of the fines and leaching the coarse fraction results in greater metal recoveries than obtained by leaching only. Tests with a chalcocite-bearing quartz monzonite mine waste sample that had been crushed to minus 6 inches and screened on 1/2 inch yielded copper and silver recoveries of 71 and 22 percent, respectively, by the combined flotation-leaching process, compared with 48 percent of the copper and no silver recovered leaching the run-of-mine material. Copper was more readily leached from the coarse material with the minus 1/2-inch fines removed than from material with the fines included. The improved leaching was attributed to improved permeability and the associated improved circulation of air to the interior of the ore column. Cost estimates showed that the proposed intensive treatment of mine waste will require a greater capital investment and higher annual operating costs than conventional milling and dump leaching process. However, the income from the additional metal production offsets the increase in capital investment and operating costs, resulting in additional profit.

Jan 1, 1975

By S. P. Sandoval

Several researchers have shown that the surface of chalcopyrite becomes hydrophobic under oxidizing conditions. Because dissolution of copper from chalcopyrite in dump leaching occurs under oxidizing conditions, the U.S. Bureau of Mines studied the effect of surfactants on chalcopyrite leaching under dump chemical conditions. Surfactants were selected for study because they can lower interfacial tension. The tests were conducted in shaking water baths using 250-mL Erlenmeyer flasks in statistical experimental design formats. The addition of nonionic surfactants increased copper extraction in the fernc sulfate leaching of chalcopyrite when sufficient Fe3+ was present. A positive interaction between Fe3l+ concentration and surfactant concentration was demonstrated. Copper concentration in the leachhing solutions was increased by as much as 100 pct at 25° and 50° C by adding nonionic surfactants. ionic surfactants decreased leaching. The structure of the nonionic surfactants and their hydrophile-lipophile balance (HLB) influenced surfactant performance. The branched hydrophile of an ethoxypolyol was beneficial to surfactant performance. The ethoxypolyol was the superior surfactant at 25° C, but became unstable at 50° C. Four surfactants, an ethoxyalchohol and three block copolymers, performed best at 50° C.

Jan 1, 1990

Control the release of ground-water into active underground coal workings by short-term pumping from dewatering wells sited on fractures. Approach The sudden release of fracture-stored groundwater into underground coal workings often occurs when mine workings are developed beneath fracture valleys, Pumping from fracture trace-sited dewatering wells, prior to development of the underlying workings, can be an efficient means of intercepting fracture-stored groundwater before it is released into the mine. Dewatering operations are discontinued once the underlying mine workings have been fully developed, and the maximum possible reduction in fracture storage has been achieved through pumping. How It Works An aerial photographic technique known as fracture trace analysis is used to site dewatering wells on rock fractures in a valley bottom. Downhole caliper and temperature logs are used to assess the fracture flow potential of each dewatering well drilled.

Jan 1, 1987

By W. H. Young

THE BITUMINOUS coal and lignite industry increased substantially in 1962, compared with the 1961 figures. The major items of production, consumption, exports, and productivity increased. However, certain key items declined. The steady upward trend in mechanization failed to materialize for the third year; the percentage of total tonnage mechanically loaded remained the same as in the 2 previous years; and the tonnage mechanically cleaned was smaller than in the previous year. The percentage of total production mined by stripping and by augers increased slightly. Most significant was the continued decline in average value and employment. Production.-The output of bituminous coal and lignite in the United States in 1962-422 million tons-was 5 percent greater than the 403 million tons produced in 1961. Production was greater in 1962, owing largely to expanded consumption by the electric utilities and to more exports.

Jan 1, 1963

By Richard H. Spencer

Since the passage of the Coal Mine Health and Safety Act of 1969, the Bureau of Mines has made many advances in mine communications. These efforts have resulted in the following developments and demonstrations: Surface-to-surface electromagnetic transmission of baseband voice signals through overburdens as deep as 600 feet. This transmission was achieved with equipment from the Interim Mine Rescue and Survival System Program, and demonstrated that baseband voice communications could be obtained through these overburdens in the absence of mine-generated noise; that is, when the mine power system was shut off, However, during mine operational conditions, the mine-generated noise proved to be so large that effective baseband voice communications to the desired depths could not be effected.

Jan 1, 1975

By A. V. Hooker, E. J. Coggeshall

"The Bureau of Mines for some time advocated the firing of all blasts in coal mines as single shots, and this method of firing is the general practice in American bituminous-coal mines. All single shots can be fired with permissible single-shot units so designed that they will not ignite mixtures of methane and air.If several shots in a face are fired singly it is necessary to return the face after each shot. In some mines having steeply pitching coal seams, this may be dangerous or even impossible, under these conditions shots are usually fired simultaneously.Several shots cannot be fixed simultaneously with permissible single-shot blasting units, and safe types of multiple shots blasters are not readily available. This means that the firing of multiple shots in gassy mines is usually accompanied by the possibility of gas ignition as the blast occurs.Tests have been made at the Pittsburgh Experiment Station to determine the possibility of developing safe types of multiple-shot units suitable for such use, or of applying other type safely in gassy sections of mines where firing shots singly is impracticable.The tests may be divided into the following four groups:1. Tests to demonstrate hazard in the use of existing types of multiple-shot units of the portable generator type.2. Tests to show the electrical characteristics of multiple-shot generator units relative to the possibility of preventing igniting sparks and of modifying the design and application of such units in furthering safety."

Mar 1, 1935

By M. M. Tilman

The purpose of this investigation was to determine the effects of small amounts of cobalt in nickel on the tensile properties and hardness of representative types of austenitic stainless steels . Cobalt substitutions for nickel up to 2 weight - percent were made in types 302 and 309 stainless steels . Data were obtained at room temperature for tensile strength , yield strength , percentage elongation , percentage reduction in area , and hardness . In type 302 steels , tensile strength and hardness increased with increased percentages of cobalt , percentage elongation and reduction in area decreased , and yield strength showed little change . Property changes were largely due to the reduction of nickel content rather than to the addition of cobalt . In type 309 steels , only minor variations were observed for the properties investigated ; the effects of the relatively snall cobalt substitutions and nickel reductions were somewhat reduced by the higher total alloy content .

Jan 1, 1964

By Terry S. Cory

This report covers antenna design, analysis, and development work suited for use with a wireless radio communication system operating at medium frequency. The work includes the test and evaluation of prototype vehicular antennas developed during the program.

Jan 12, 1978

By Doris M. Hyde

Mineral industry activity in many of the smaller Caribbean Island countries has remained minimal. For this reason, specific references to Bermuda, Guadeloupe, Martinique, and the Netherlands Antilles have been removed from textual and trade table presentations. Any significant future developments will be reported as they occur. Readers are referred to earlier Minerals Yearbook editions for previous information. Table 1 production statistics have been modified in some instances. References to certain nonmetal commodities were eliminated because information has often been unreliable. Their inclusion in table 1 was not considered important to either an overview of the area or to compatibility with volume I of the Minerals Yearbook.

Jan 1, 1984

By L. C. Headley

A series of exploratory tests was conducted to determine the effects of steady electric fields on fluid flow and streaming potential in narrow passages and porous media, the effects of steady electric fields on fluid interfaces, and the influence of internal voltages on fluid flow in a porous porcelain sample. Voltages greater than about 5 kilovolts were found to influence liquid droplets emanating from a capillary tube. Solutions of polyethylene oxide and polyacrylamide in water exhibited widely different behavior than that of other liquids tested. Liquid-liquid displacement tests in porous samples to determine the influence of high voltage applied to the displacing liquid on flow rates and recovery gave no significant differences. No consistently measurable effects were noted, either on flow rate or streaming potential, when an electric field was applied transverse to the direction of flow in porous media and in narrow rectangular or cylindrical channels. Experimental values of formation factor and streaming potential for a porous porcelain sample agreed qualitatively with those calculated from electrokinetic theory for ultrafine capillaries. However, the agreement for the electroviscous effect was not good.

Jan 1, 1970

By William Hustrulid

The National Institute for Occupational Safety and Health (NIOSH), as part of a comprehensive program to improve mine safety through the widespread acceptance of careful excavation principles in drifting, have revisited standard drift round design concepts. Although the initial emphasis was on contour row design and providing improved design tools for blasting with de-coupled charges, the focus has broadened into the development of a general gas pressure-based drift round design approach. The concept of a damage radius (Rd) for a given explosive-hole-rock mass combination is introduced. With the damage radius as the basic building block, the blast holes are positioned on the face, beginning with the buffer row, to achieve the desired excavation size, shape and smoothness. The design of the contour row of holes is also performed using a pressure-based approach. The paper presents in some detail the overall approach and the required gas pressure-based design equations.

Jan 1, 2007

By William B. Harper

Domestic sales of carbon black sustained the upward movement for the 4th consecutive year, reflecting the increased sales of motor vehicles during the same period. Sales of carbon black in the domestic market topped 2 billion pounds for the first time during 1965 and have more than doubled the output of 20 years earlier. By far the largest user of carbon black is the rubber industry. That use accounted for more than 94 percent of the carbon black consumption with the bulk of it being used in tire casings and tubes. Thus demand for carbon black is naturally sensitive to trends in the sales of passenger cars and other motor vehicles, Manufacturers of inks, paints, plastics, paper chemicals, and food are also important users of carbon black.

Jan 1, 1967

By Phil Patton, Bill M. Stewart, Curtis Clark

Handling materials in underground mines continues to be a major safety problem. To help reduce materials-handling injuries, the National Institute for Occupational Safety and Health (NIOSH) at the Spokane Research Laboratory is developing, modifying, and testing equipment to replace the necessity of doing lifting tasks manually. To reduce single-event lift injuries, equipment having mechanical automatic weight sensing and balancing control was investigated. The Coleman manipulator was selected for testing. Modifications to the Coleman manipulator to make it more suitable for underground mine use included mobilization, self-containment, all-purpose gripper attachment, and support jacks. To reduce or eliminate the need to clean off manually the materials that commonly plug grizzly openings (timbers, wire mesh, roof bolts, and other debris), a track-guided pincher arm device was developed. The TGPA attaches to an impact hammer head, and the pincher arms are controlled by the operator of the hammer. Oversized rock can be broken with the pincher arms in the up position; the arms can then be lowered to grab and remove debris. Sweeping action to remove cohesive fines bridging grizzly openings is also greatly improved. This device is especially useful in recessed grizzlies. An industrial gun was tested to evaluate its effectiveness in breaking oversized rock. Boulders up to 76 cm in diameter were successfully broken to minus-33 cm. Although methods to control fly rock need to be developed, an industrial gun may be a safe and inexpensive alternative to breaking oversized rock in certain underground mining situations.

1. PURPOSE The Temporary Face Support System (TFSS) consisting of beams, posts and carrying-emplacing equipment was developed to provide temporary supports between the working face and the permanent roof supports. 2. GENERAL DESCRIPTION The system consists of: ? A Beam And Post Carrier And Deployer (BAPCAD), a self-propelled machine that carries as well as emplaces the beam-and-post sets. ? Lightweight mechanically self-deploying posts designed to safely support a load of 10,000 pounds each. ? Lightweight constant strength beams (bars) capable of sustaining an approximate equally distributed load of 8500 pounds. Note. All referenced figures and drawings are found at the back of this manual.

Jan 1, 1980