Search Documents

By W. C. McLaughlin

Under a cooperative agreement, the Bureau of Mines, Magma Copper Co., and ASARCO, Inc., tested backfilled ground support systems at t.wo elevations in Magma's San Manuel, AZ, mine. The tests were mainly for guidance in designing the loading crosscuts of the new ASARCO Sacaton underground mine. Two-piece, wide-flange steel sets for 8-by 8-ft (2.44-by 2.44-m) and 11-by II-ft (3.36-by 3.36-m) openings were designed. Set spacing was 3 ft (0.91 m) and 5 ft (1.52 m), respectively. After erection, the sets were lagged with various test materials. The void between the lining and the ground was backfilled with sand and pea gravel. Instruments measuring strain (used to determine changes in stress) were placed beneath the sets and in the backfill. Results indicate the backfilled sets in the smaller drift (2315 grizzly level, panels 6 and 7) of 8-by 8-ft (2.44-by 2.44-m) cross section are a viable permanent support system, lower in cost than the standard formed concrete. Results are inconclusive in 2615 grizzly level, panels 5 and 6, where wide-flange steel sets were used with 5-ft (1.52-m) long concrete gob lagging of T-design.

Jan 1, 1983

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United states was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United states Department of the Interiors This paper is a continuation of a series made in cooperation with the Coordinating Fuel Research (CFR) Committee of the Coordinating Research Council (CRC), Inc. The first of this series of reports presented data on motor gasolines sold during the winter of 1935-36, and succeeding reports described motor gasolines sold during the summers and winters to and including the summer of 1941.£1 No reports were made on motor gasolines sold during the winter of 1941-42 and during the summer of 1942. However, starting with the winter of 1942-43, the semiannual reports were resumed

Jan 1, 1949

By Floyd G. Anderson

The Federal Bureau of Mines promotes the use of safe and effective dust-collecting devices for rock drilling in coal mines. To insure that such devices are available to the coal-mining industry, the Bureau issues certificates of performance for dust-collecting systems and certificates of approval for dust collectors and rock drills or other mining equipment with integral dust-collecting systems that meet the requirements of an established Schedule.4/ Investigations are conducted under the provisions of the current revision of this Schedule by engineers of the Branch of Health Research. This circular describes briefly the requirements and procedure for obtaining certificates of performance or approval and lists equipment that has been certified as permissible under Schedule 25 or its revisions as of January 31, 1961. The names and addresses of companies to which certificates have been issued are listed alphabetically at the end of this circular.

Jan 1, 1961

By J. B. Gayle

Oven widths for experimental and commercial slot-type ovens differ appreably in most instances; the experimental ovens usually ranging from 10 to 14 inches and the commercial units from 14 to 21 inches. Application of results obtained with experimental ovens to commercial practice thus requires major extrapolations. A critical survey of the literature indicated that sufficient information about the effects of variations in oven width on the carbonizing process is not available to permit such extrapolations to be made with any considerable degree of confidence.

Jan 1, 1960

By Howard W. Kilau

The U.S. Bureau of Mines is investigating surfactants added to water sprays to enhance the control of dust during coal mining operations. The objective of the present work was to establish the general applicability of adding sulfate ion to anionic surfactant solutions in order to improve wetting action. This was pursued through laboratory wettability testing of four anionic surfactants and one nonionic surfactant in combination with various concentrations of sulfate ion. The experimental results demonstrated that the addition of sulfate ion enhanced the wetting characteristics of all the anionic surfactants when applied to hard-to-wet coals, while easy-to-wet coal showed more complex wetting behavior. Sulfate ion in the presence of nonionic surfactant enhanced wetting only slightly or not at all. Surface tension measurements of the dilute aqueous surfactant-sulfate anion solutions indicated this property was not important in coal-wetting phenomena, as long as the value was below the critical value for coal. Sulfate ion helps surfactant reduce surface tension but primarily appears to affect wetting action by altering the adsorption characteristics of surfactant on the coal surface.

Jan 1, 1990

By Paul L. Russell

This property has been examined several times in the last few years , and findings have been reported . In the fall of 1942 , the author supervised sampling both lode and placer deposits . The ore was beneficiated , and the results obtained are incorporated in this report . stia The Morgan Group , which comprises seven unpatented mining claims and the Black Cat placer claims , was purchased by the Manganese Products Corp. from H. D. Hill of Hatch , N. Mex . , and Dr. A. C. White of Hot Springs , N. Mex . Arthur L. McRowe , 876 27th Avenue , San Francisco , is president of the corporation , and David Fewer, 824 Times Building, Long Beach, is treasurer . J. T. Murray is in charge of operations .

Feb 1, 1947

By Alexander M. Gow

This paper summarizes a survey of fine-grinding practice in ore-concentrating plants throughout the United States, Alaska, Canada, Mexico, and Cuba as reported in the Bureau of Mines Information Circulars on milling methods. The survey covers 49 concentrators, which have a combined capacity of over 160,000 tons per day. In these plants 470 ball, rod, and pebble mills prepare material for flotation, gravity concentration, amalgamation, cyanidation, and air separation. The ores are those of gold, silver, copper, lead, zinc, molybdenum, feldspar, and pyrite. The metallurgy is that of the period 1928-32. Of these 49 concentrators, 36 are in the United States. They can treat 134,400 tons per day, and they have 326 fine-grinding mills. In the United States there are about 100 active or temporarily idle concentrators, exclusive of the many plants in the Tri-State zinc district, the washeries of the Lake Superior iron ranges and the Florida phosphate area, and small gold and silver concentrators. These 100 plants have an estimated capacity of 290,000 tons per day and employ about 650 ball, rod, and pebble mills. Consequently, since this paper covers about half of the production of this country it may be considered as particularly representative of fine grinding in ore mills in the United States.

Jan 1, 1933

By Liane L. M. Kacinuck

This U.S. Bureau of Mines publication is intended to provide mining industry representatives and regulatory authorities with a reference package dealing with studies on hydrology and underground mine subsidence. An annotated bibliography and a list of additional sources are given and represent references published prior to June 1993. Ninety-two references ware identified and 72 obtained for assessment. Annotating the references included evaluating the study methodology and summarizing the basic results. The references are also compiled based on geographic location to aid the user in identifying articles of particular interest.

Jan 1, 1994

By Mark S. Sanders

This report is a review and synthesis of the published literature dealing with personal equipment items used by low seam coal miners. This report reviews the following items of equipment: headgear, outer garments, respirators, cap lamp, gloves, knee pads, footwear, boots, helmets, ear protection, eye protection. Recommendations for further research and development are included.

Jan 1, 1978

By W. A. Stickney, J. W. Town

Studies on continuous - circuit leach - aluminum precipitation and leachelectrodeposition of mercury were made by the Bureau of Mines to determine optimum conditions and cost estimates for recovering mercury from mercury sulfide flotation concentrates . With 150 grams of sodium sulfide and 50 grams of sodium hydroxide per liter , from 98 to 99.8 percent of the mercury was extracted from flotation concentrates , with about 0.5 pound of sodium hydroxide used per pound of mercury produced . Precipitation of mercury from the caustic - sulfide solution with minus 8 - mesh aluminum shot required about 0.2 pound of aluminum per pound of mercury produced at a cost of $ 0.05 per pound of mercury . Electrodeposition cost with 7 mill power , based on 50 percent current efficiency , was below 2 mills per pound of metal deposited . Feed solutions ranged from 10 to 130 grams of mercury per liter , and current densities , from 2 to 70 amperes per square foot . The cost of open- pit mining 250 tons per day was estimated at $ 1.75 per ton , and flotation - leachingelectrodeposition of the ore , at $ 3.54 , resulting in a cutoff grade of about 0.1 percent mercury . The cost of underground mining 50 tons per day was estimated at $ 20.00 per ton , and the cost of milling the ore was estimated at $ 13.33 , which resulted in a cutoff grade of 0.6 percent mercury .

Jan 1, 1964

By H. F. Yancey

This report, dealing with the separation of coal from its associated impurities by means of a pulsater-type jig, continues the series of reports that have been issued by the Bureau of Mines, in which detailed study has been made of the efficiency and mechanism of separating coal and impurities in various coal-cleaning appliances. The previous reports have dealt with the piston jig, coal-washing table, pneumatic table, and Baum-type jig. Such studies of the separation accomplished by any form of concentration device are essential and necessarily preliminary to any intelligent attempt to improve the performance of such equipment Object and Plan The pulsator-type jig was developed recently by G. A. Vissac. Although two articles(2) describing plants using this typo of cleaning unit appeared in 1936, both dealt principally with plant design and layout rather than with plant performance The object of the stork described in this report was to determine the efficiency of the separation made by the pulsator jig on a sized feed, the specific gravity at which the separation between coal and impurity was effected, and the influence of the specific-gravity composition of the coal on the character of the separation made.

Jan 1, 1938

By G. W. Jones

[The determination of the ignition tcqornturc ol" dict:iyl cther and othylene in air ma o;GrT;en rir..ic'r. is dcscribed In thin report J'IF.R mqdo primarily for comparison rritll sinilnr d~ton:in:~tions of ot; cr co~~o~imS-r, in the same apparatus and using the r?.:?.r.~o 1a.borntorg t cchzllique The investigation was conducted at the 2ittsbur;;h Experiment Station of the United States wcau 02 hii2cs vritEl tl~c cooperation of licrclc & Co., Inc.]

Jan 1, 1935

By Robert K. Koch

The reactions of alumina and alumina monohydrate with wet hydrogen fluoride gas were studied by the Federal Bureau of Mines to determine the feasibility of producing commercial-grade aluminum fluoride from offgases generated by pyrohydrolysis of siliceous fluorspars. The test results showed than an aluminum fluoride reactor operating at maximum efficiency could retain 96 percent of the fluorine contained in off-gases generated by pyrohydrolysis of siliceous fluorspar. The requirements are a reactor temperature of 200° C. and a reactor entrance gas containing 5 mole-percent hydrogen fluoride. Partial pressure equilibrium constants were determined for the reaction of alumina monohydrate and wet hydrogen fluoride gas from 200° to 350° C. and for the reaction of alumina and wet hydrogen fluoride gas from 350° to 700° C. Both reactions are reversible, and they proceed in directions that are dependent upon the temperature and the relative HF:H2O concentration. Logarithms of the equilibrium constants were used to plot the reaction isobars; these can be used to calculate the theoretical maximum efficiency of a reactor processing wet hydrogen fluoride gas between 200° and 700° C. The theoretical maximum efficiency decreases with increasing temperature.

Jan 1, 1961

By Scott Turner

Many of you radio listeners have probably never seen a mine . You may be glad of it, but you should not forget that there is a vast army of men in this country who not only have to see mines , but have to work in them day by day in order that you may be supplied with many of the things you need. Specifically , nearly a million men work in the mines of the United States , 700,000 in the coal mines , 110,000 in the metal mines , 100,000 in other mines and quarries , and 75,000 in the oil and gas fields . On a stormy night , the average citizen is apt to think of the perils of the seaman . Particularly in the old days before steamships , many a prayer went up " God help the poor sailor on a night like this . " At the same time , the sailormen often expressed fear for the poor landlubber , exposed as he was to the danger of falling chimneys , swaying signboards , and uprooted trees . So with the miner . Many of you may pity him , for working underground in complete darkness except for feeble artificial lighting , mining coal or ore , drilling hard rock , handling explosives , and perhaps breathing vitiated air . On the other hand , on stormy days , with rain , snow or hail falling , and with the temperature low , or on hot bright days , I have often heard miners joke about the poor fellows who had to stay " on top, " and could not get " down below" where there was no wind , where no snow fell, where the temperature was unchanging , and where a man could have his own working place , arranged to suit himself , with little interference from meddlers and with no automobiles to dodge . So do not feel too sorry for the miner . He is quite apt to be a strong , healthy , hearty person , making pretty good wages , and fairly well contented with his lot .

Dec 1, 1930

By K. K. Kershner

Nickel having a purity of more than 99.99 percent with reference to metallic impurities was electrodeposited at the Rolla Metallurgy Research Center of the Federal Bureau of Mines. The production of high-purity nickel is in keeping with the current trend in technologies for producing metals with lower and lower percentages of impurities. To understand more fully the role to be played by nickel by itself and as a component in many alloys, the element must be in a state of high purity. Procedures are outlined for purifying nickel solutions by precipitating and filtering off impurities. Details are given for using the purified solutions as electrolytes in depositing high-purity nickel. The elecneleposited nickel contained 0.0005 to 0.002 percent each of cobalt, copper, aid iron together with spectrographically detectable traces of aluminum, magnesium, and silicon. The deposits were smooth and dense; the crystalline structure was typical of an electrodeposited metal. Some preliminary experiments for purifying nickel solutions by liquid-liquid extraction are also described in this report. Tests of this type were limited since more encouraging results were obtained by other methods of purification.

Jan 1, 1961

By James J. Dowd

The investigation to evaluate the reserves of coking coal is being made by the Bureau of Mines in three parts: (1) To estimate known (measured plus indicated) recoverable reserves of all coking coal, (2) to upgrade marginal coals through effective preparation, and (3) to study the carbonizing properties of coal and coal blends not now widely used for metallurgical coke making. This is the seventh of a series of reports giving the results of studies by counties under part (1) of the investigation. (See appendix.) This report covers Floyd County, KY., which comprises parts of the Paintsville, Prestonsburg, Harold, Hindman, and Pikeville quadrangles. (See fig. 1.) A base map for each bed in each quadrangle was made to the scale of 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all avail-able data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds up to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick. These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas, areas excluded from the estimate but which may contain reserves based only on geologic inference, and areas outside of the outcrop were measured by planimeter on the base maps. Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1951

By Oliver C. Ralston

Fluorescence is of growing interest to the mineral industry because certain minerals may be detected thereby and because, as shown in figure 1,4/ many minerals (natural or synthetic) are needed in tubes and lamps. The use of fluorescent lighting is expanding, and large numbers of lamps of many sizes and shapes are being made and used in works, factories, stores, offices, homes, and in photography. Fluorescent tubes, as distinguished from clear tubes filled with neon, argon, or other rare gases through which a current of electricity passes, fluoresce owing to specially, selected and prepared minerals placed in the tubes. Luminous chemicals and paints also contain special minerals and are used in similar applications; therefore, these also will be considered in this report. Although the quantity of minerals (in tons) that are used for fluorescent purposes is small, and probably will continue to be so, this use is significant because it exemplifies a requirement for "pure" minerals in which a trace of contaminant as" minute" as one part in ten million may distinguish between the acceptance or rejection of a particular material. This extreme purity makes synthetic minerals almost essential, and natural mineral's are now little used.

Jan 1, 1944

By R. M. GRANTHAM, J. H. SOULE

C. R. Keyes, F. C. Schrader , F. A. Jones ( the first director of the New Mexico School of Mines , whose name was given the deposits ) , and N. H. Darton all described the Jones iron deposits within a decade after their discovery in 1902 . The earliest locations now on record were made in 1927. Interest in iron ores was revived during the second World War . Paul E. Pesonen , of the Bureau of Mines , reported on the deposits in December 1941 and proposed an extensive exploratory program . In March 1942 , the deposit was reported upon by C. H. Johnson , also of the Bureau of Mines , and a definite program of exploration was outlined .

Feb 1, 1947

By Gregory J. Chekan

The Bureau of Mines, in an effort to improve planning and development in coal mining, is investigating strata interactions associated with mining of multiple coalbeds. Two common interactions that occur between adjacent coalbeds are subsidence and pillar load transfer. The study described involves underground observations and measurements conducted at two Pennsylvania mines, each affected by one of these interactions. At the mine affected by subsidence, measurements show that undermining had little effect on upper mine pillar stability, but had a more severe effect on the development and maintenance of entries. Roof-to-floor measurements recorded over four times more convergence in entries developed over gob as compared with entries developed over support pillars in the lower mine. At the mine affected by pillar load transfer, Initial in situ measurements have shown the existence of a pressure arch in the lower workings. Prior research has shown that arch interaction between two adjacent openings can create stress concentrations in the in-nerburden. Underground measurements and results obtained from both mine sites correlate with theoretical and photoelastic multiple-seam models, and eventually these field data will serve to refine model accuracy. Further study of multiple-seam interaction mechanisms will lead to improved mine planning, increased resource conservation, and a safer working environment.

Jan 1, 1986

By Frank C. Morris

This report presents the results of a Bureau of Mines study to identify clays found in several petroleum-reservoir rocks in the Tejon-Grapevine area, Kern County, Calif., and to determine the effect of water sensitivity of the clays on the permeability of the reservoir rocks. The clays in the porous rocks were examined in detail, and the clay-mineral types were identified by differential thermal analysis, X-ray diffraction, and optical and dye-staining methods. Fresh-water damage to the permeability of the oil-reservoir rocks was indicated by a study of 125 core samples from productive formations. The study indicated that, although clays were generally less than 5 percent of the reservoir rocks, they swelled in water, particularly fresh water, and nearly blocked the flow channels through which oil flows to the well, effectively reducing the permeability of the formations. The average permeability of rock decreased from 1,600 millidarcys in air to 620 millidarcys in salt water and 120 millidarcys in fresh water. The dominant clays in the oil-bearing sandstones were members of the montmorillonite group. They were associated with smaller quantities of clays found to be in the mica or illite group. None of the cores appeared to contain clays of the kaolinite group. In the lower section of the J.V. sandstone indications of what appeared to be the mineral sepiolite were noted.

Jan 1, 1959