Search Documents

By Thomas M. Barczak

This U.S. Bureau of Mines report describes methods to enhance the capacity, stiffness, and timber utilization of wood crib supports. Since stiffer supports minimize strata deflections that contribute to roof instability, efforts to maximize crib stiffness while maintaining stability through a wide displacement range should be a design priority. The stiffness and capacity of conventional crib designs, employing alternating layers of wood timbers that are loaded perpendicular to the grain, can be increased by increasing the interlayer contact area or by using higher strength wood. Contact area can be increased by using wider timbers or employing more timbers per layer. Concepts that provide parallel-to-the-grain timber loading will provide substantial increases in crib stiffness and capacity. Two concepts that utilize this principle are examined: (1) an original South African design that constructs wood cribs from preformed layers (mats) of timber where short blocks are oriented vertically between horizontal slabs; and (2) a design that employs full lengths of timber placed vertically in the interior of a conventional crib structure. These designs also provide more efficient timber utilization by providing greater support capacity per volume of wood used in the crib construction.

Jan 1, 2010

By P. L. Sibrell

The U.S. Bureau of Mines has tested cyanide leaching for recovery of palladium (Pd) from spent petroleum processing catalysts. Three different catalyst samples were supplied by a spent-catalyst processor. These catalysts consisted of a zeolite base and contained 0.4 to 0.7 pct Pd. During alkaline cyanide leaching, the catalysts exhibited ion-exchange properties due to their zeolite matrices. Hydrogen ions were released from the zeolite in exchange for sodium ions in solution, resulting in a significant decrease in solution pH. This could present a safety hazard because of the potential for release of toxic hydrogen cyanide gas. A pretreatment step where the catalysts were contacted with a 1.0M sodium hydroxide solution was found to prevent the pH shift from occurring. Following the sodium hydroxide pretreatment, two stages of leaching at 160 °C with solution containing 1 pct sodium cyanide and 0.1[M] sodium hydroxide gave at least 75 and up to 95 pct Pd recovery. The Pd was quantitatively recovered from the leach solution by thermal decomposition in an autoclave at 250°C for 1 h. The Pd content of the precipitate was over 50 pct. Thermal decomposition also decreased the total cyanide content of the barren solution to less than 0.2 mg/L. The catalyst leach residues passed the Federal Toxicity Characteristic Leaching Procedure and the California Waste Extraction Test, indicating that landfill disposal of the leach residues would be acceptable.

Jan 1, 2010

By J. F. Smith

A series of studies of emissions from large coal-fired steam generators have included measurements of the concentrations of oxides of sulfur and oxides of notrogen. The sampling equipment, method of sampling, and analytical techniques used for processing of these samples are detailed. A method based on the precipitation of benzidine sulfate was developed for determining both SO3 and total oxides of sulfur in the presence of interfering acidic components in the stack gases. In addition, difficulties encountered with sampling and analytical techniques are also described.

Jan 1, 1968

By C. H. Gorski

Evaluation of raw materials for mineral wool is one phase of the Bureau of Mines broad program for the more effective utilization: of our mineral resources. The experimental work and test-evaluation results on several raw materials as useful components for the production of mineral wool are presented in this report. Samples from all sections of the United States, including copper slag from Tacoma, Wash., pebble phosphate slime from Florida, and granites from Massachusetts and Minnesota, have been blown into mineral wool successfully in the laboratory tests. Maximum conservation of the Nation's mineral and manpower resources requires maximum utility of those resources. Al though the domestic reserves of oil, gas, and coal are tremendous, judicious use of these fuels through the use of proper insulation will insure the highest thermal efficiency. The effectiveness of mineral wool as a heat-insulating material has assumed an increasingly important role in the national economy, and it has become a fuel saver in countless applications. The most immediate concern to many is the use of mineral wool in the home, which promotes uniform temperature and minimizes drafts by reducing heat transfer through the walls, ceiling, and floors. There are, however, many industrial and commercial uses that require large volumes of mineral wool each year.

Jan 1, 1951

By W. H. Pomroy

This report describes research by the U.S. Bureau of Mines to design and in-mine test a rapid response pneumatic fire detection system for multilevel metal mines. The relative merits of pneumatic detection are discussed in the context of typical multilevel mine layouts and environments. The Bureau's prototype system is described, with emphasis on design features that counter commonly experienced and/or perceived operating problems with pneumatic detection systems. Finally, the results of a 3-year in-mine performance evaluation of the prototype system are discussed.

Jan 1, 1990

By D. Eugene Rannels, Yu-Chen Lee

"Lee, Yu-Chen, and D. Eugene Rannels. Alveolar macrophages modulate the epithelial cell response to coal dust in vitro. Am. J. Physicl. 270 (Lung Cell. Mol. Physiol. 14): L123-L132, 1996.-The response of the alveolar epithelium to coal dust exposure is poorly understood. Coal or other dusts may act on the epithelium directly or indirectly through nearby alveolar macrophages (AM) that produce cytokines and other soluble products. AM and type II pneumocytes (T2P) were thus exposed to dust in coculture to evaluate their possible interactions. Anthracite coal dust PSOC 867 increased synthesis of extracellular matrix (ECM) components by T2P. AM alone did not produce ECM. Similarly, coculture ofT2P with AM (3.75:1) had little effect on epithelial ECM synthesis. In contrast, coculture ofT2P with AM significantly increased PSOC 867 effects on T2P rates of ECM synthesis, ECM fibronectin content, and T2P levels of fibronectin mRNA. AM-conditioned medium did not change the PSOC 867 effect on T2P. Neither control nor PSOC 867-treated AM on Falcon culture inserts (0.45-µm pore size) over T2P stimulated ECM synthesis by either untreated or dust-exposed epithelium. Thus AM-mediated changes in ECM synthesis by PSOC 867-treated T2P require close cell-cell interactions, suggesting a role for cell-cell contact or for short-lived soluble mediators of the AM effects. DEVELOPMENT OF PNEUMOCONIOSIS, a chronic disease of coal workers that results in pulmonary fibrosis and low lung compliance, is associated with inhalation of mineral or coal dust in the work place (14). Although the pathology of pneumoconiosis has been studied extensively, cellular mechanisms that cause changes in lung structure and function are not fully understood. Particulate matter that enters the respiratory system distributes according to size, with larger particles being removed in proximal airways. Dust components of small size may enter distal alveolar region, which is populated by two types of epithelial cells, type I and - type II cells, and by alveolar macrophages (16). Each of these cell types may interact with inhaled particles, but only the effects of coal dust on alveolar macrophages have been studied extensively. Less is known regarding the response of the alveolar epithelium, or of effects on epithelial cell-alveolar macrophage interactions, in the dust-exposed lung.Function of the alveolar epithelium is well known to be influenced by the underlying basement membrane, or extracellular matrix (28). Alveolar epithelial cell extracellular matrix interactions, which may involve modulation of cell migration, attachment, or differentiation (17), are reflected in type II cell morphology, metabolism, secretory activity, hormone responsiveness, lamellar body content, and gene expression (21). The extent to which basement membrane modulates differentiation of the overlying epithelium is determined by both molecular composition and three-dimensional structure of the matrix. Type II epithelial cells in vitro synthesize, secrete, assemble, and degrade a variety of basement membrane components, including laminin, fibronectin, type IV collagen, and thrombospondin (22, 27). How expression of these components is regulated, directly or indirectly, upon exposure of the alveolar epithelium to injury by coal dust or by other particulates remains to be resolved."

Jan 1, 1998

By D. Harrington

Although for many years considerable attention has been given to devising safe and efficient methods of using explosives, with some success, relatively little has been done to provide satisfactory storage facilities for them. This was known long before the present war began, but it was emphasized during the past 30 months? inspections of explosive magazines by employees of the Bureau of Mines in administration of the Federal Explosives Act of December 26, 1941. These inspections have revealed woeful in adequacy as well as definite hazards and the urgent need for obtaining better storage facilities either by remodeling old magazines or constructing ink new ones that would afford suitable protection for the contents against theft, fire, deterioration, and detonation. The purpose of this paper is to offer suggestions and to show by sketches and drawings some of the fundamental features of suitable magazines. Type of construction and available materials differ with different; localities, but the information herein contained can be applied to most magazines, whether already constructed or the construct: on of which is planned. It is hoped that this information will be helpful and will aid persons who are trying to provide suitable storage for explosives end detonators. It is also hoped that States and cities will be made aware of the unbelievable laxity practiced in storing explosives in the United States and will take some remedial action.

Jan 1, 1945

By R. Hogg, Y. Lee, D. E. Rannels

"Lee, Yu-Chen, Richard Hogg, and D. Eugene Rannels. Extracellular matrix synthesis by coal dust-exposed type II epithelial cells. Am. J. Physiol. 267 (Lung Cell. Mol. Physiol. 11): L365–L374, 1994.—Although integrity of the alveolar basement membrane may influence progression of lung injury induced by inhaled particulates, little is known about direct effects of coal dusts on the alveolar epithelium or its extracellu¬lar matrix (ECM). Effects of dust on synthesis of cell and ECM proteins by type II cells (T2P) was thus investigated. Three coal dusts (anthracite no. 867; bituminous no. 1451 and no. 1361) and mine dust MIT-3, of respirable size, were studied as a function of dose and time over 3 days of primary T2P culture. On day 1, 750 µg/ml of 867 were required to increase relative synthesis of ECM proteins (ECM/cell). MIT-3, 1451, and 1361 were without effect. By day 3, 867 or MIT-3 increased ECM/ cell 60-100% at 300 µg/ml; 1451 produced modest, dose-dependent stimulation, whereas 1361 remained without effect. None of the dusts caused significant cytotoxicity. The results show dose- and time-dependent effects of well-characterized coal and mine dusts to modify partitioning of newly synthesized proteins into the ECM and suggest that coal dust exposure may modulate structure or function of the subepithelial basement membrane.basement membrane; cell culture; inorganic dust; lung injury; extracellular matrix deposition; pulmonary epitheliumCHRONIC EXPOSURE to coal dust may be associated with development of pulmonary fibrosis and consequent loss of normal lung function (see Ref. 26 for review). Al¬though the pathways of inorganic dust-induced lung injury are recognized to involve an inflammatory re¬sponse, the underlying pathogenic mechanisms are not understood in detail. Acute and chronic responses to dust exposure involve a variety of interacting cells of the immune system, including macrophages, T cells, and B cells, along with pulmonary fibroblasts. These responses reflect direct effects of the dust particles, as well as indirect effects mediated by soluble factors, including cytokines and eicosanoids (see Ref. 41 for review).Studies of pulmonary macrophages and fibroblasts following silica exposure suggest that dust-induced damage at the airway surface may involve cellular injury through oxidant-mediated pathways. Coal dusts and related inorganic particulates can activate the alveolar macrophage (42) to produce fibronectin (15) and cytokines, such as interleukin-1 or tumor necrosis factor (4) and/or other soluble products which act locally (29) to cause acute cellular injury and to initiate the progression of fibrotic lung damage (16). Type I epithelial cells are typically more susceptible than type II cells to oxidant injury. Type I cell damage and subsequent death leads to denudation of the subepithelial basement membrane (2, 21) and can be associated with leakage of plasma constituents from the pulmonary vasculature into the alveolar compartment (13)."

Dec 1, 1995

By Andrew Cecala, John Organiscak, William Heitbrink

Many types of heavy equipment used in the mining and construction industries use enclosed cabs to protect equipment operators from dust and noise exposure. Normally, when the equip- [ ] ment is new, manufacturers' deigned controls are effective at keeping the operator's exposure at acceptable level. However, as equipment becomes older and many components of the enclosure deteriorate, such as gaskets and seals, the effectiveness of the enclosed cab can be greatly reduced. This can cause excessive and dangerous exposures to respirable dust, especially when the ore or overburden contains crystalline silica.

By A. C. Smith

The U.S. Bureau of Mines developed an experimental method to evaluate the relative effectiveness of water additives on the extinguishment of coal fires. The experiments were conducted in the fire zone of the multiple-entry section of the Bureau's Bruceton Experimental Mine. Four-hundred-pound Pittsburgh Seam coalbeds were ignited and allowed to burn until well-developed fires were achieved. Extinguishing agent-water solutions were then applied to the fires, and the quantity required to extinguish the fires was compared with the quantity of water alone required to extinguish similar fires. A 20% diammonium phosphate-water solution required an average of 5.8 gal to extinguish the coal fires, while two commercially available additive-water solutions required an average of 8.1 and 8.0 gal, respectively. The average amount of water required to extinguish the fires was 7.4 gal. An analysis of covariance, using the thermal energy of the coalbed to quantify the fire at the time of extinguishment, showed that the diammonium phosphate-water solution was slightly more effective at extinguishing these coal fires than water alone, and the two commercially available additive-water solutions were statistically equivalent to water alone.

Jan 1, 2010

By N. C. Tomoeda, W. D. Bensema, J. W. Adams

Measurements of surface magnetic field noise were made at various locations over the Geneva Coal Mine near Price, Utah, on June 12, 1973. The locations selected were on the surface over emergency locator beacons underground at depths between 350 meters (1150 ft .) and 488 meters (1600 ft .) . The surface terrain where these measurements were made was mountainous, and access was difficult. There were no power lines within several miles, and the weather was clear; therefore, the magnetic noise levels were about as low as will normally occur. Results of measurements of distant sferics indicate rather sharp cutoff frequencies below which broad- band, impulsive noise is attenuated. The mechanism of propagation for this noise above the daytime cutoff frequency of 3500 Hz and the nighttime cutoff frequency of 1700 Hz is deduced to be a waveguide formed by the D or E layers of ionosphere as an upper plane and the earth as a lower plane. The measurement systems used are similar to those used earlier. The technique is to record broadband, analog signals, digitize the data, and use a fast- Fourier transform to obtain spectral plots. This tech- nique is novel in that it can measure simultaneously all magnetic field energy within a limited portion of the spectrum for a limited time, and, after processing, reproduce the events occurring in that time interval in great detail .

Jan 6, 1974

By A. E. Raddatz

The Federal Bureau of Mines, as part of its goal to minimize undesirable environmental impacts associated with mineral processing, has investigated a soda-smelting technique for processing ilmenite into pig iron and a titanium slag that is suitable for a feed to a sulfate-process titania pigment plant. By this procedure, the generation of ferrous sulfate waste and its associated disposal problem is obviated. Molten titania slag was quenched, water leached, and filtered to yield a sodium titanate intermediate product containing about 70 wt-pct Ti02, 1 wt-pct Fe, and 20 wt-pct Na20. This intermediate product, high-soda titanate (HST), was mixed with H2S04, calcined, quenched, and water leached to produce a low-soda titanate (LST) product that contained only 2 wt-pct Na20. Both the HST and LST were evaluated as feed materials for preparing titania by the sulfate process. About 95 pct of the Ti02 was extracted from HST and LST by digestion in concentrated or 50-wt-pct-H2S204 solutions. About 95 pct of the solubilized Ti02 was subsequently recovered from the titanyl sulfate solutions by hydrolysis. Barren solutions from hydrolysis, containing about 26-wt-pct H2S04, were upgraded by vacuum-thermal evaporation or electrodialysis. The regenerated acid solutions were used to digest additional HST and LST.

Jan 1, 1979

By A. L. Engel

In recent investigations of chloride Volatilization of gold at the Reno Station, it was found that the addition of small amounts of copper and NaCl to the charge brought about improved volatilization of the gold. The investigations described in this report were concerned with the recovery, in an aqueous medium, of fumes from chloride volatilization of gold. It was attempted to discover a suitable aqueous medium that would permit absorption, solution, or precipitation of all the volatilized gold immediately upon contact with the medium. A simple laboratory apparatus was employed to produce fumes by volatilization. To this furnace was attached an absorption train consisting of a series of chambers containing the aqueous medium, through which the fumes were drawn by suction. A satisfactory synthetic ore that contained metallic, gold in a quartz-matrix was made and utilized, enough. gold being present in a' small amount of material to permit an accurate, metallurgical balance of the volatized values' to be obtained in all the experiments.

Jan 1, 1949

By L. R. Burdick, J. F. Barkley

"The agglomerating index of coal is an index based upon the nature of the coke residue left when the standard volatile-matter determination of the well-known proximate analysis is made. In this determination a small amount of coal is heated in a container to about 950° C. (1,742° F.), at which temperature the volatile matter is driven off, leaving a coke formation. The coke residues for various coals are quite different in physical structure: and, for some time past, work has been done on studies of the nature of these residues in connection with the coking of coal. In 1934 Gilmore, Connell, and Nicolls proposed use of the agglomerating index for indicating the dividing line between noncaking coals and those having weakly caking properties. 4/ Its use was adopted in the standard classification of coals by rank as a requisite physical property index to differentiate semianthracite from low-volatile bituminous coal and also high-volatile ""C"" bituminous from subbituminous ""A"" coal, as shown in table 1, the standard coal classification adopted by the American Society for Testing Materials and the American Standards Association. 5./In studying the agglomerating properties of coals based on the coke residue the Bureau of Mines has adopted the notation given in table 2. Coals that in the volatile-matter determination give a coke residue either in the form of an agglomerate button that will support a 500-gram weight without pulverizing or a button that shows swelling or cell structure are considered to be agglomerating."

Nov 1, 1938

Control shearer-generated airborne respirable dust on longwall mining sections. Approach Previous Bureau studies have shown that using high-pressure water can have a significant impact on the amount of airborne dust released into the face airflow while cleaning and controlling the airflow in the immediate cutting zone. The basic concept to improve the drum water spray system was to utilize high-pressure (1,200 psi) inward-facing drum sprays to improve the dust knockdown efficiency of the spray system and confine the dust to the face area. This system would minimize the exposure of the shearer operator through dust avoidance and decrease face dust levels by suppressing the amount of respirable dust that becomes airborne. System Design In-mine tests were designed to provide information that would permit evaluation of the operation with different spray orientations and water spray pressures. This was achieved by comparison with a conventional baseline wet-cutting system consisting of 26 low-pressure bit sprays, located on the hit blocks to provide pick-point flushing. Total drum water flow was 60 gpm and was maintained continuously throughout all tests. The high-pressure inward-facing drum water spray system consisted of sprays located in each bit block, oriented 15° and 30° toward the face. The inward-facing water spray system was operated at either 800 or 1,200 psi.

Jan 1, 1989

By K. E. Stanfield

The Bureau of Mines oil-shale program, initiated in April 1944, is concerned with the future utilization of oil shale in the United States as a source of liquid fuel. One phase of this program is the accumulation of information on the location, extent, and richness of oil-shale deposits that may be suitable for processing to oil and related products. A previous publication5/ presented, by means of logs, the oil yields of sections of the largest known oil-shale deposit in this country -the shales of the Green River formation occurring in adjoining portions of the states of Colorado, Utah, and Wyoming. This present supplementary report presents the oil yields of cores from 48 holes drilled during 1952 to 1954 in the Green River formation of Colorado, which is distributed over an area of more than 1,000 square miles. The oil yields of the 48 oil-shale sections, involving the assay of 9,651 samples, representing 22,451 feet of core, are presented by means of logs. In addition, the oil yields of samples comprising the maximum sections of 15 gallon-per-ton shale are tabulated for these cores and for the 28 cores from Colorado which were logged in the previous report.

Jan 1, 1957

By C. Fang, D. B. Kittleson, K. L. Rubow

"Under contract to the U.S. Bureau of Mines, a study was conducted to investigate the feasibility of using the microorifice. uniform deposit impactor (MOUOI) to measure the size distribution of aerosols containing various mixtures of coal dust and diesel exhaust particles. The project objective was to determine if the mass concentration of diesel exhaust particles, in an airborne mixture of coal dust and diesel exhaust particles, could be determined on the basis of the size distribution of the two aerosols. In general, the mass of diesel exhaust particles is in the submicrometer size range while that of the coal particles lie in the larger size ranges.The MOUDI is a cascade impactor with small diameter nozzles to obtain small cut sizes and rotating impaction plates to avoid particle overloading of the deposit. For this study, a 7 stage version was used. At the sample flow rate of 30 L/min, the cut sizes were 0.10, 0.23, 0.70, 1.0, 2.6, 4.9 and 10 pm.Size distributions of aerosols generated in the laboratory and in several underground coal mines were measured. The primary emphasize of the laboratory tests was to ascertain if the diesel exhaust particles could be separated from the coal dust, regardless of mass fraction of the diesel exhaust particles in the total aerosol mixture. Diesel exhaust, from a Caterpillar Type 3304 NA diesel engine, was mixed with coal dust generated with a· TSI Model 3400 fluidized bed dust generator. Experiments showed the size distributions of the mixed aerosols exhibited two definite modes with the minimum between the two modes in the 0.7 to 1.0 um size range. Distinct modal separation was obtained as the mixture fraction of the diesel exhaust aerosols was varied from 3% to 98%.The field study was conducted in three underground coal mines, two utilizing diesel-powered equipment and the third exclusively using electric equipment. Sampling sites were selected to obtain a wide variety in the diesel exhaust and dust aerosol concentrations. Size distribution data showed these aerosols are bimodal. The mass median aerodynamic diameters of the diesel particulate mode and the coal dust mode were approximately 0.15 µm and 3 to 10 un, respectively. The results, in all cases, clearly show a separation between the two modes in the 0.7 to 1.0 µm size range with the minimum in the vicinity of 0.8 pm. The separation was found to be independent of mass fraction of the diesel exhaust particles, total particle concentration and sampling site."

Jan 1, 1989

By J. E. Dooley

Reference mass spectra and analytical correlations for 20 alkylcycloalkyl sulfides and two dicycloalkyl sulfides are presented 'to provide information that will facilitate the identification of sulfur compounds occurring in natural or synthetic mixtures. Reference spectra indicate relative intensities in addition to parent and base peak sensitivities. Analytical correlations establish the ionic species that reflect major fragmentation paths for the com-pounds studied. Specifically, the correlations show that base peaks are formed by several different processes: (1) Cleavage of the bond a to the ring, (2) fragmentation of the alkyl chain, and (3) fragmentation of the ring plus fragment contribution from the alkyl chain. Useful correlations for deter-mining alkyl chain length involve the CnH2+3S+ and CnH2n+1 + ions. CnH2n-2+ and CnH2n-1 S+ ions reveal the number of carbon atoms in the cyclic ring. Other important ionic species are also discussed.

Jan 1, 1970

By Richard D. Miller

The helium resources base of the United States was estimated by the Bureau of Mines to be 1,070 Bcf as of January 1, 1985. These resources are divided into four categories in decreasing degree of assurance of their existence: (1) helium in storage and in proved natural gas reserves, 280 Bcf, (2) helium in probable natural gas resources, estimated at 243 Bcf, (3) helium in possible natural gas resources, estimated to be 287 Bcf, and (4) helium in speculative natural gas resources, which makes up the remaining 260 Bcf. These helium resources are further divided into depleting, non-depleting, and stored classifications. The depleting resources are those associated with natural gasfields that are, or will be, produced for the natural gas they contain. Almost all of the helium in potential (probable, possible, and speculative) natural gas resources is included in this classification. These depleting resources are estimated to contain 900 Bcf of the total helium resource base. Helium resources contained in nondepleting natural gas resources, those in shut-in, abandoned, or otherwise nonproducing natural gasfields, are estimated to total 133 Bcf. There is 37 Bcf of helium in storage in the Federal Government-owned Cliffside Gas Field near Amarillo, TX.

Jan 1, 1987

By David C. Byrne

PURPOSE: Evaluate practical technological advances in level-dependent hearing protectors and inexpensive personal acoustic monitors. RESEARCH SUMMARY: The results of previous NIOSH research show that miners develop hearing loss much more quickly than nonoccupationally noise-exposed individuals and that miners experience a greater severity of hearing loss than would be expected for nonoccupational noise-exposed persons of the same age and gender. Using hearing thresholds at 4,000 Hz as an indicator, coal miners experience hearing loss 2.5 to 3 times greater than would be expected for persons not exposed to occupational noise. At age 50, 90% of coal miners and 49% of metal/nonmetal miners were found to have a hearing impairment. In comparison, only 9% of a nonoccupationally exposed control group had a hearing impairment at age 50. There are numerous barriers to the prevention of hearing loss among miners. In an effort to overcome some of these obstacles, this work was initiated to evaluate practical technological advances in level-dependent hearing protectors and inexpensive personal acoustic monitors. Experiments will involve analysis of this new technology under both laboratory and field conditions. Laboratory components will consist of controlled studies using an anthropometrically correct test fixture as well as human subjects to evaluate the adequacy/effectiveness of various hearing protective devices. Electroacoustical performance testing of new noise monitors will also be conducted in a laboratory setting. Subsequent field studies will determine the actual usefulness and practicality of the personal protective/monitoring equipment as used in different mining situations. It is anticipated that increased on-the-spot awareness of hazardous noise levels and the availability of better-suited hearing protectors will provide a degree of protection beyond what is currently attained in different mining environments. Therefore, the intent of this project is to identify and adapt new acoustical technologies and products that have a direct application to individual mine workers. With increased knowledge of these technological advances, a greater demand for similar devices will likely occur, which, in turn, will lead to a better understanding and awareness of hearing loss prevention methods throughout the mining community. The ultimate goal is for widespread integration of useful hearing loss prevention products and devices into the daily routines of miners

Jan 2, 2000