Search Documents

By N. H. Coates

A small, special-purpose centrifugal compressor was developed to circulate 60 pounds per hour of helium at 1,000° F and 250 psig because standard, commercial units were not available. Performance characteristics of this compressor were determined at helium flows of 2,000 to 18,000 std cu ft per hour, pressures of 100 to 250 psig, and temperatures of 100° to 1,000° F. This range is 2 to 90 actual cu ft per minute. Several graphs show the adiabatic head developed by the compressor over this wide flow range at various combinations of temperature and pressure. A compressor performance map relates pressure ratio to mass flow, temperature, pressure, and speed. This map can be used to accurately predict compressor performance factors within the range of operating conditions covered by the experiments.

Jan 1, 1963

The purpose of this study is to develop designs to facilitate and accelerate auger rotation stoppage (and auger rotation start up so as to promote auger disengagement during auger miner repositioning) and to provide a time delay and warning signal prior to auger start up to permit any miner s near the augers to get away from the augers before they start rotating. In the underground coal mines in the U.S., there are four auger miners that are currently in use. They are the Jeffrey 100L (see Figure 1-1) and 100M (see Figure 1-2), and the Wilcox WCM and the MK20A (see Figure 1-3).

Jan 1, 1974

By H. H. Schrenk, L. B. Berger, W. P. Yant, F. A. Patty

"The use of small such as canaries and white mice, for detecting carbon monoxide depends primarily on the fact that the volume of respiration of these animals in proportion to their volume of blood is much higher than for man. Accordingly, when animals and men are simultaneously exposed to a given concentration of carbon monoxide the animals will absorb it more rapidly and attain serious poisoning in less time than men. Prom a practical viewpoint the use of the animals depends on the margin of time between observable symptoms in them and serious poisoning in man, during which man can return to fresh air or use respiratory protection. It should be remembered, however, that during the time the animal is incurring a detectable degree of poisoning, man is also absorbing some carbon monoxide, and the margin of time is not very wide. Experience with canaries has shown that an occasional specimen may have a tolerance above the average of the species and fail to exhibit symptoms before man incurs a very discomforting and possibly a serious degree of poisoning.It is also well known that physical activity increases the demand for oxygen by the body, and the respiratory exchange and circulation of the blood are increased to meet the demand. This sets up a vicious condition if carbon monoxide is present in the air because the rate of absorption of carbon monoxide is not only increased by the increase in respiration and circulation, but the absorption of carbon monoxide decreases the capacity of the blood for carrying oxygen at a time when the demand is high. These facts, together with the increase in respiration and circulation which attend excitement, underlie the caution to be calm and to walk slowly and to reduce physical exertion to a minimum when exposed to carbon monoxide. For these same reasons, when using animals for detecting carbon monoxide it is endeavored to keep them active, thereby tending to increase the response of the birds and widen the time between observable effects in the birds and effects in the man. As rule canaries are kept fairly active through fright at the unnatural surroundings and in their endeavor to remain on the perch of the cage when carried into the atmosphere to be examined. They also experience an excitement stage with oncoming carbon monoxide poisoning. Sometimes, however, especially if the air is cold, they tend to be inactive and quiet. Ordinary mice and white mice become inactive with use and also with oncoming poisoning. They huddle in the corner or the cage, and thereby not only reduce their sensitivity but make it difficult to observe signs of poisoning."

Oct 1, 1930

By R. C. Diehl

Coal, fly ash, and flue gas samples were analyzed for mercury (Hg) by double gold amalgamation-flameless atomic absorption spectrophotometry. The purpose of the study was to elucidate the fate of the trace mercury in the coal when the coal is burned. Samples were collected from a bench-scale 100-g/hr combustor, a 500-lb/hr combustor, and three coal-burning powerplants. In all cases mercury was found in the fly ash. The amounts ranged from about 9 to about 70 percent of the mercury in the coal that was burned.

Jan 1, 1972

By Victor Himel

This report documents a systematic approach towards implementing an improved ensemble for the mine rescue team system that will protect against the hazards of mine rescue and recovery and will also afford improved performance through increased comfort and maneuverability, lighter burdens, and improved human engineering designs. In the first part (Task 1) the mine rescue team's protective needs were defined along with the test methods required to evaluate whether a particular piece of gear met these needs. Task 2 assessed existing gear against performance criteria and standards developed in Task 1. Task 3 consisted of the conceptual design and construction phases of the MRPE program. Special consideration was given to advanced concepts, materials, and equipment.

Jan 1, 1982

By Frank W. Sansom

This paper is one of a series of articles dealing with milling methods and costs at metal mines in the United States, written in accordance with an outline prepared by engineers of the United States Bureau of Mines and published by the bureau. The Netta mine and concentrator is the largest of the plants of the Eagle-Picher Lead Co, It is located in Ottawa County, in the extreme northeast corner of Oklahoma, and in what is known as the Tri-State zinc and lead mining district, embracing the northeast corner of Oklahoma, the southwest corner of Missouri, and the southeast corner of Kansas. A majority of the production comes from the Oklahoma section, with Kansas second, and Missouri third.

Jan 1, 1930

By Steve W. Webb

The Bureau of Mines is researching a new technology for dewatering clay suspensions that consists of flocculation by high-molecular-weight poly-ethylene oxide (PEO) polymer and subsequent removal of water from the floes via a trommel. The minimum amount of PEO required to dewater the clays depends on the ions adsorbed on the surface of the elay particles. Infrared studies were performed on clays with Li+, NH4+, K+, Mg2+, Ca2+, Ba2+, or 8r2+ adsorbed, with and without adsorbed PEO, to develop data to aid in understanding the dewatering mechanism. Hydroxyl stretching modes between 3,400 and 3,250 em-I, associated with water adsorbed on the clay, showed changes in intensity proportional to the ionic eharge-to-radius ratio; that is, the ionic potential. In addition. a water-bending vibration of adsorbed water at 1,630 cm-1 showed variations associated with water desorption. The data are consistent with changes in adsorption of PEO resulting from variation of the acidity of water coordinated with the exchange ions, induced by the variation in field strength of the ions with the ionic potential.

Jan 1, 1986

By Hugh Haddow

This paper describing the methods of recovery and treatment of a sand and gravel deposit and the preparation of these materials for a number of special markets is one of a series being prepared by the U. S. Bureau of Mines. It is of particular interest to those sand and gravel operators who have a surplus of fine sand which must be sent to waste, both from the point of view of, equipment and the variety. of markets supplied, and in that it describes one of the few sand and gravel plants which have resorted to hydraulic classification for sizing fine sand. ACKNOWLEDGMENTS The author wishes to acknowledge the assistance of J. R. Thoenen, mining engineer of the Bureau of Mines, in the preparation of this paper.

Jan 1, 1931

By R. K. Conrad

The Bureau of Mines conducted corrosion research to determine suitable construction materials for geothermal resource recovery plants. Weight loss, pitting and crevice corrosion, U-bend stress corrosion, and electrochemical polarization measurements were made on selected metals in brine and steam process environments produced from high-enthalpy hypersaline brine from geothermal well Magmamax No. 1 at the Salton Sea Known Geothermal Resources Area, Imperial Valley, Calif. Cadmium (and by extension cadmium coatings) and a 6061-T6 aluminum alloy were unsatisfactory because of high general corrosion rates and, in the case of aluminum, severe pitting Molybdenum and niobium (columbium) were resistant to general corrosion, pitting, and crevice corrosion, Copper alloys corroded at rates that may preclude their use in wellhead brine, The presence of iron accelerated the corrosion of the copper alloys Titanium alloys were resistant to general corrosion and stress corrosion cracking in all of the environments. They exhibited crevice corrosion in some of the brine and steam environments and Ti6A14V pitted in the brine environments. They exhibited passive behavior over a broad range of potentials. Exposure tests were conducted on a high-temperature polyphenylene sulfide thermoplastic (Ryton) in the same environments. A 40-pct-graphite fiber-reinforced Ryton composite deteriorated readily in wellhead brine and failed in all of the brine and steam process environments; Ryton coatings on 316L stainless steel were adherent and performed well.

Jan 1, 1983

By C. C. Stevenson, Thomas Varley

"The art of treating ores by the chloride volatilization process is still in the experimental stage. The process has not been sufficiently developed along chemical and metallurgical lines to state definitely just what place it will occupy in the metallurgical industry. The theory upon which the process operates has received the attention of prominent metallurgists for the past twenty years, and research and experimental work has been conducted by many investigators.Much of the experimental work done has never been published, and it seems that the accumulation of such results if made known would be an important aid to the further development of the process. The object of this paper is, therefore, to bring salient features of the process to the attention of the metallurgical industry, both for the purpose of furnishing information, and receiving from interested parties any comments which the reading of this article may suggest. A bulletin covering the work done at the Intermountain experiment station of the U. S. Bureau of Mines, situated at Salt Lake City, Utah, is in course of preparation.The chloridizing roast is usually accompanied by appreciable losses due, to the volatilization of the metals as chlorides during the roast, these losses often running as high as 30 per cent, depending upon the temperature, the character of the ores and the associated gangue material. It was not until 1891 that Croasdale, (Croasdale, Stuart, Engineering and Mining Journal, Aug. 29 1903) by observing this and stack deposits from the chloridizing roast, recognized the possibility of making volatilization a major instead of a minor feature of the roast. He then made tests on a large number of tires from different, localities, the result of which showed the, general application of the process. The main difficulty, as stated, by Croasdale, was the lack of a suitable means for recovering the fume from the furnace gasesIn 1913, Cottrell (See Mining and Scientific Press, March 29, 1913; alsoTrans. American Institute of Mining Engineering, September 1918. (Additional informa-tion is available from the owners, The Research Corporation of New lark, and Western Precipitation Co., .Los Angeles, Calif.), announced his invention of the electrostatic precipitator, which solved the problem of separating the solids from the furnace gases."

May 1, 1921

By Anthony W. Sparks

The Bureau of Mines conducted tests designed to compare its breathing metabolic simulator (BMS) with other methods that are currently used to evaluate the performance of respiratory protective equipment. The BMS is a commercially developed device that uses a piston cylinder to simulate breath movement. Using a propane furnace that consumes oxygen and forms CO2, the BMS also simulates the respiratory metabolism of humans. The breathing and metabolic subsystems of the BMS are described in detail in this report. Results are compared from tests that used the BMS to evaluate respiratory equipment and from tests that used human subjects for the same purpose. The BMS was also tested against a pulsatile breathing machine (PBM) previously designed by the Bureau. Both machines were used to test respiratory equipment, and the test results are compared in this report. To illustrate typical applications of the BMS, the report briefly describes how the BMS was used to test two different types of closed-circuit respiratory apparatus, and the test results are presented. This research showed that BMS test results compared more closely to the results of tests that used human subjects than did results obtained using the PBM.

Jan 1, 1980

By T. L. Joseph

"IntroductionThe efficiency of ore reduction in the blast furnace and fuel requirements depend upon the degree of uniformity with which reducing gases can be distributed through the stock column and upon the permeability of individual pieces of ore and sinter. If the ore is fine, the major problem in reduction is to get the ascending gas stream to the surface of the ore-Hard, dense ores of low permeability, mined in coarse sizes, tend to improve the permeability of the bed, but unless they are crushed to the proper size they reach the hearth unreduced.Surveys by the Bureau of Mines have shown conclusively that the gas distribution in the upper three fourths of the furnace is far from ideal. Furnace lines, top design, and methods of charging are important, but more thorough size preparation of the ore is necessary to eliminate size segregation at the stock line, which inevitably leads to non-uniformities in gas distribution.Because of the quantity of sinter now produced close study of the characteristics which determine its behavior in smelting is warranted. As the use of concentrates increases agglomeration will become more of a necessity. Improvements in the physical character of the ore burden are particularly important to plants using coke of poor physical quality. In addition to aiding reduction, improved physical properties of the ore burden will permit the use of higher blast heats, which is equally important.Reduction Tests on Fine Sizes of SinterPrevious reduction tests on minus 0.742— plus 0.525--inch pieces of commercial sinters revealed large differences in porosity and reducibility. The results have been published in a former report. 3 Although the physical properties of the sinter, particularly porosity, were found to be of major importance in determining the rate of deoxidization, it appeared that certain chemical properties of the sinter appreciably retarded the reduction of sinters high in silica. This was attributed to the presence of fayalite, which has been identified by Schwartz and by Luyken and Kraeber4 as an important constituent of sinter. Although furnace operators and metallurgists have assumed that iron silicate is more difficult to reduce than hematite or magnetite, definite data on the reduction characteristics of this material were not available. Tests were undertaken, therefore, to develop a method for de-termining the amount of iron silicate present in sinters so that its effect upon reduction could be observed."

Jun 1, 1934

By J. C. Duchon

The use of extended workdays or compressed workweeks (regular shift lengths exceeding 8 h) is attracting growing interest in many industries using continuous operations. While extended workdays promise increased worker satisfaction due to more days off, including weekends and holidays, there are legitimate concerns about the potential effects on the health and safety of such a schedule. The U.S. Bureau of Mines (USBM) conducted a study at a Canadian underground copper, lead, and zinc mining operation that was designed to study the safety and performance implications of extended workdays. Measures were taken before and after a change from the old 8-h continuous schedule to the new 12-h continuous schedule, including behavioral performance measures to analyze perceptual-motor changes, continuous heart-rate monitoring and aerobic capacity to measure physical fatigue, a variety of self-report questionnaires to measure perceived adaption and satisfaction with the new schedule, and pulmonary-respiratory measures to examine air contaminant exposure. Based upon the overall acceptance of the new schedule by the workers and lack of change in fatigue-sensitive behavioral and physiological performance measures, this study recommends that the mine retain the 12-h schedule. However, certain precautionary measures are suggested to insure the safety of the workers.

Jan 1, 2010

By A. J. Kraemer

"Introduction In 1925 the Bureau of Mines published as Technical Paper 346 a discussion of typical crude oils of the Western Hemisphere. That paper was one of a series of surveys of typical crude oils, and was the first of these to deal with properties of crude oils from countries other than the United States. The paper contains comments, tabulated data, and individual analyses of crudes typical of the producing districts of Canada, Mexico, Trinidad, Venezuela, Argentina, Colombia, and Peru; for comparison, it also has analyses of typical crudes from the chief producing districts of the United States.The Bureau of Mines undertook a study of foreign crude oils for two reasons: First, foreign fields are potential sources of supply for the United States; in fact, considerable quantities of some foreign crudes have already been imported. Second, these oils are very similar in physical and chemical properties to oils found in the United States, and a study of these resemblances has scientific value.After the publication of Technical Paper 346, the attention of the Bureau was called to the fact that the two analyses of crude oil from Venezuela which appeared in that paper were not completely representative of the production of that country. Samples of other types of oil were procured through the cooperation of Mr. R. Ogarrio, manager of the Texas Petroleum. Co., Huston, Texas, and officials of the following companies operating in Venezuela; British Controlled Oilfields, Ltd., Venezuelan Oil Concessions, Ltd., Creole Syndicate, and Venezuelan Gulf Oil Co.. Samples were collected and dispatched by Mr. D. 3. Park, representative in Maracaibo, Venezuela, of the Texas Petroleum Co. The value of the interest and cooperation of these agencies in obtaining the samples is gratefully acknowledged."

May 1, 1927

By Alan G. Mayton

The Bureau of Mines conducted one of the most extensive studies on surface mine illumination to date, to assess the illumination needs of mobile surface mining machinery with respect to the visual tasks required of machinery operators. Field Investigations were performed at 22 surface mining operations, coal and metal-nonmetal, within several mining regions of the United States. Visibility and illumination were measured for 159 visual tasks performed by equipment operators on or near 57 surface mining machines, including draglines, shovels, blasthole drills, bulldozers, loaders, haul trucks, graders, scrapers, and several service-type vehicles.

Jan 1, 1987

By Ann G. Kim

The Bureau of Mines estimated the methane content of a coal, which depends primarily upon rank and pressure, from the adsorption equation V kpn, where k and n are constants related to rank. By incorporating corrections for moisture, ash, and temperature, and estimating pressure and temperature as a function of depth, the methane content of coal in place can be estimated from the following equation: [ ] Values calculated with this equation generally are in reasonable agreement with direct determinations. By assuming a standard moisture and ash content, and using the hydrostatic head to estimate pressure, a graph of rank and depth versus gas content was constructed. Although estimated values were consistently high for several high-volatile bituminous coals from an area where the pressure is known to be less than hydrostatic, the estimated methane content for most coals shows reasonable agreement with values determined by the direct method.

Jan 1, 1977

By D. E. Wolfson

This report presents 900° C BM-AGA carbonization and related data for coals from the principal beds of Nicholas, Randolph, and Webster Counties, W. Va. Thirty-three samples from nine coal beds in three counties were car-bonized at 900° C in the l8-inch-diameter BM-AGA retort, data from which have been correlated with industrial production. Host of the samples were chemically suitable for metallurgical use, and their coking properties were satisfactory. Except for four of the Lower Kit-tanning samples, the ranges of constituents in the coal seams were 1.8 to 9.0 percent ash and 0.4 to 1.1 percent sulfur, values within the range of accept-ability for metallurgical coals. Coke strength indexes were normal for Appalachian coals of similar rank, and the tumbler stability indexes of the coke ranged from 35 to 57.

Jan 1, 1969

By James E. Hill

In the course of exploratory drilling during World War II by the Bureau of Mines under the Strategic and Critical Minerals investigations Program, a problem arose as to the ultimate disposal of the drill core resulting from that program. The difficulties experienced in obtaining factual information to evaluate mineral deposits examined (during that program) influenced the Bureau in a decision to catalog and store the drill cores for future reference. Initially, the drill cores were stored at the nearest Bureau of Mines station that had space available for the purpose. Recently the Bureau stations at Minneapolis, Minn., and Denver, Colo., were designated as the locations of permanent drill-core storage facilities. Drill cores that are retained from Bureau of Mines mineral-exploration projects are stored at these two locations and are given preference in selecting cores for storage. Drill cores are accepted also for storage from other Government agencies, State agencies, private companies, or individuals on the basis of available facilities and consistent with the significance of the core in relation to Bureau of Mines objectives and national interest. Selection and acceptance of such drill core are determined by the Bureau of Mines. The drill cores stored at the two locations are available for inspection by any person having a legitimate interest in the mineral deposits represented by the cores. Approximately 1,850,000 feet of drill core can be stared in the facilities now available to the Bureau of Mines. Approximately 475,000 feet of drill care is stored or scheduled for storage at Minneapolis, Minn., and 240,000 feet of core stored or scheduled for storage at Denver, Colo. A list of drill core now in storage at the Bureau of Mines core-storage facilities at Denver and Minneapolis is included as appendix A.

Jan 1, 1957

By R. H. Dickson

This paper, which describes the milling practice of the Verde Central Mines, Inc., is one of a series on milling methods and costs being prepared by the United States Bureau of Mines. GENERAL DESCRIPTION The Verde Central concentrator is located in Walnut Gulch, about 1 mile west of Jerome, Ariz., and on the Jerome-Prescott highway. It is about 1,000 feet distant from the main shaft of the Verde Central mine and treats ore from this mine only. The mill is connected with the main shaft of the mine by a 24-inch gave railway, over which the ore is hauled in 5-cubic yard capacity, rocker, side-dump cars, by a 3-ton Brookville gasoline locomotive.

Jan 1, 1931

By L. A. Neumeier

The Bureau of Mines evaluated creep and other properties of extruded Zn-30 pct-AI alloys containing 0 to 0.7 pct Mg. The alloys were extruded both above and below the Zn-Al eutectoid temperature of 275° C. Creep behavior is defined for the alloys as extruded and after various heat treatments. Tensile properties, hardness, thermal expansivity, impact resistance, and microstructures are given. The alloys, either with or without magnesium, required substantially less pressure for extrusion near 275° C than at higher or lower temperatures. The alloys containing magnesium exhibited significantly greater hardness, tensile strength, and creep resistance, but much lower ductility than the 2n-30 pct Al alloy. The properties were very sensitive to the processing conditions.

Jan 1, 1971