Search Documents

By R. B. Schluter

Magnetite pellets were simultaneously reduced and indurated on a laboratory scale in order to determine the effects of temperature, induration time, degree of metallization, and sulfur content upon the physical and chemical properties of prereduced pellets. The reductants were commercially-pure tank gases. Among the findings were these: 1,100° C is the minimum temperature that will produce acceptably hard pellets using carbon monoxide as the reduc-ing gas. Prolonged treatment time improves the pellets' crushing strength, but the rate of improvement falls off sharply after 2 hours' induration. At 1,120° C, 75-percent metallization produces the maximum crushing strength; there was no corresponding peak at 900° or 1,050° C. Sulfur in the furnace atmosphere lowers the required induration temperature. A few tenths of 1 percent sulfur in the pellet increases the sintering rate of metallic iron in pellets by forming a liquid FeS phase that facilitates iron transfer.

Jan 1, 1968

By Ralph B. Stevens

The objective of this 20-month program was to define the relationships between mine ventilation, temperature, humidity, ore properties, material's used in mine operations, etc., and the spontaneous combustion problem in underground metal mines. Tradeoff studies of availability, reliability, cost, and maintenance of spontaneous combustion protection sensors and telemetry were conducted, after which a prototype system was selected from four design alternatives. This selected system was then laboratory tested and demonstrated in an underground copper mine.

Jan 1, 1979

By Jon G. Bredeson

The electromagnetic noise that exists in a mining environment is quite severe and was shown to have been reasonably well documented by a number of researchers in the Phase I Report. The noise levels are such that prudent communication design requires the careful use of all the electromagnetic noise data available. A comprehensive survey was undertaken to determine techniques used in various industrial environments to achieve secure communications in the presence of electromagnetic interference. The techniques were given in the Phase I Report and are rudimentary, but have produced reasonably good results. A number of these techniques could be applied to the mining environment.

Jan 1, 1980

By E. A. Mevissen

With the ever increasing consumption of mineral commodities, the vital question is not whether sufficient mineral quantities will be available, but rather can the known existing low grade resources be mined economically. Conventional conveyor systems are being used in some open pit mines to decrease haulage costs. n an effort, to take this concept one stop further, this contract study examines the use of a high angle conveying system in an open pit mine. It identifies available high angle conveying equipment and examines the haulage and crushing costs associated with both a conventional truck and shovel mining operation and a high angle conveyor operation. These costs analyses were performed on a hypothetical copper, taconite and phosphate mine. Information was gathered from a series of high angle conveying equipment and open pit mining operations in the U.S. Volume I includes a detailed review of the state-of-the-art in high angle conveying concepts, the, hypothetical mine development, and the cost analyses. Volume II includes the appendices.

Jan 1, 1981

By Michael Schmitz, John A. Organiscak

ABSTRACT: A method (patent pending) has been developed to determine the quality of environmental cab filtration systems. This method utilizes specially configured filter cartridges to remove carbon dioxide from the ambient air with the environmental cab’s air filtration system. A real-time gas monitor is placed inside an unoccupied cab with the filtration system running to time decay the carbon dioxide to its lowest concentration or equilibrium level. The outside carbon dioxide concentration level can be measured concurrently with another gas monitor or with the same inside cab gas monitor during a representative period before and after the inside sampling is conducted. Cab filtration system leakage is comparatively deduced from the difference between the special cartridge filter efficiency and overall cab efficiency. Laboratory trials have illustrated that desirable high efficiency test filter configurations (greater than 99 % efficiency) can be devised, but have air quantity and test time limitations. These trials also demonstrated that CO2 penetration was reflective of controlled air leaks around a high efficiency filter under equilibrium conditions. This report examines the elements of this patent pending method.

By E. A. Clarke

The vapor-phase section of the Coal Hydrogenation Demonstration Plant at Louisiana, Mo., was operated for the first time in April 1949. The run lasted only 10 days because of time limitation (pending plant dedication in May) and the small amount of charging stock available. The primary purpose of the operation was to break in and determine the operability of the equipment and to supplement the operators' classroom training with actual practice by operating the plant under mild conditions. A secondary aim was to obtain data on the hydrogenation of petroleum oil and lignite tar distillate at approximately 10,000 p.s.i. while making gasoline and Diesel fuel oil. Although the operations were carried out under conditions considerably below those used in the plant design, a great deal of experience and data was obtained. As it is not feasible at this time to conduct further vapor-phase operations on similar stocks, this report has been prepared to present and summarize the data obtained through this operation.

Jan 1, 1950

By Stephen C. Tadolini

The U.S. Bureau of Mines has developed ultrasonic measurement instrumentation capable of measuring strains and elongations on tensioned and untensioned mine roof bolting systems. This report evaluates the pulsed-phase-lock-loop and pulse-echo systems. The pulse-echo systems measure time of flight of a signal through the bolt. The ultrasonic instrument converts the measurement into elongations or stress. The most recent Bureau instrument development converts travel-time measurements directly into elongation, load, stress, and torque by simple data manipulation from the keyboard. Bolt preparation and instrument calibration are described in detail.

Jan 1, 1990

By William O. Vanderburg

This paper 3/gives the results of a reconnaissance of mining districts in Clark County, Nev., made from November 18 to December 22, 1936, and from February 9 to March 8, 1937-in all, 63 days. While the field work Was being done, virtually all of the mining districts in the county were visited and many data on active and inactive properties were obtained. The report covers the locations of the various mining districts, the nature of the deposits, information on past operations, current activity, and general data likely to be useful to operators, investors, and others interested in mining. The geology of the deposits is discussed only briefly. The principal metal-mining districts in the county are Goodsprings, Eldorado, and Searchlight. The zinc-lead ores of Goodsprings have been the most important economically, followed by the gold-silver ores of Eldorado and Searchlight. In the industrial-mineral field, gypsum, limestone, silica sand, and borates are the principal products. Metal mining in the county is characterized by numerous small operations and the ores are either milled locally or shipped to distant smelters.

Jan 1, 1937

By Tyler Blake

This report describes a study designed to evaluate a pro-posed modification in the cap lamp battery cord intented to reduce the incidence of snagging and catching of the cord. A three phase evaluation was performed comparing a prototype with the standard, currently available cord. First, a ?pull test? equipment was run. The second evaluation was a body conformity study. The third evaluation involved subjects performing common tasks in a low seam coal mine simulator. The results of these evaluations clearly demonstrated significant safety advantages of incorporating coiled cord into the design of the cap cord. The coil cord presented less of a snagging hazard, allowed the wearer more time to respond to a snag, and transmitted lower levels of force to the helmet when snagged. The research team recommended that cap lamp cords be commercially developed which incorporate coiled cord at the battery and helmet.

Jan 1, 1980

By Paul M. Tyler, R. M. Santmyers

Platinum and its allied metals osmium, iridium, rhodium , palladium, and ruthenium are the most costly of the better-known metals and combine properties that make them unique among the elements . For a number of isolated uses substitutes have been found which are cheaper and quite as satisfactory ; but none will replace platinum in many of its varied uses , and there is a large and growing demand for purposes for which no economical substitutes are known . As this paper is being written the supply of platinum tends further to increase as a result of the exploitation of newly developed resources and the expansion of production from older sources . In obedience to economic law prices have declined steadily . Buyers , always reluctant to commit themselves on a falling market , have maintained a waiting attitude , and consumption trends are not clearly indicated . Should platinum again approach the price of gold , the natural tendency would be to use more of the metal . In recent years , however , the industrial and scientific uses of platinum have become subordinate to its consumption in jewelry . In matters of personal adornment the popular whim and not practical utility is the dominant factor in demand , and it does not follow that lowered prices will stimulate demand . The substitution of white gold and certain plated goods for platinum may be checked by cheaper platinum , but a fickle public that turned from gold to platinum when platinum became the more costly metal can not with certainty be expected to buy more platinum jewelry because more of the metal than formerly may now be had for the same price . The dearth of platinum during and for some years after the World War had a profound effect upon prices , and this in turn wrought important changes in the field of consumption . When prices advanced the chemical industry, formerly the leading consumer of platinum, was forced to economize in its consumption of the metal and to substitute other metals whenever it could . Somewhat similar conditions resulted in the electrical industry and in the use of platinum in dentistry . Some of these former outlets are permanently closed , and others may be reopened now that platinum prices have receded to pre-war levels , but despite the general expansion of industrial and scientific activity since 1913 the demand for platinum outside the jewelry trade has suffered a net decline . Since the metallurgy of platinum is relatively simple the reason for its high price is its relative scarcity in the earth's crust . An interesting speculation set forth by certain geologists attributes the extraordinarily high density of the interior of the earth in part to the presence of iron alloyed with substantial amounts of platinum and other related metals . In support of this hypothesis it may be said that platinum is often found in meteorites , and known deposits in the earth's crust are all of deep - seated origin . However , even if there were a high concentration of platinum in the interior of the earth it would be next to impossible at the present state of our knowledge to make it available , and the world would continue to depend for its supply on deposits found within minable depths below the surface . For many years before 1914 the world obtained its supply of platinum metals primarily from Russia , which before the war produced as much as 300,000 troy ounces in a year , or approximately 95 per cent of the world output . Despite fluctuations due to internal political disturbances Colombia managed to account for 3 to 4 per cent , leaving the rest of the world to furnish the remaining 1 to 2 per cent .

Feb 1, 1931

By Frank T. Greene

An investigation of the quenching behavior of coal dust-air flames was carried out. The literature relevant to coal dust-air flames was reviewed, including information on the agglomeration, sedimentation, and dispersal of dust clouds. The simple equations relating the various concentrations involved in dust flame propagation are given and their implications elaborated. It is shown that the concentration seen by a moving flame in a sedimenting dust cloud can differ significantly from the concentration commonly measured in such experiments. The known dust cloud phenomena which appeared significant in flame propagation studies were experimentally evaluated, and quenching diameters, flame speeds, and lean propagation limits for several tube diameters measured. For Pittsburgh seam coal, the Minimum Quenching Diameter (MQD) for dust between 10 and 20 µm was found to be between 0.7 and 0.8 cm, and the lean propagation for 3.2-cm tubes to be approximately 200 mg/liter. Similar MQD data were also obtained for Pocahontas and Sewell coals, Beulah lignite, and a 50-gal./ton oil shale. The effect of temperature, coal particle size, and propagation tube material were also investigated.

Jan 1, 1981

By L. R. Herrmann

The most fundamental feature of fracture is that it involves separation. Such separation can arise by either separation of molecules, more or less along the line joining their centers (tension), or by d sliding separation roughly perpendicular to that line (shear). Theoretically, a perfect crystal could never be broken by the application of perfectly axial compressive stress (until some sub-molecular actions occur). In tension fields the calculated forces between molecules are extremely high. Consequently, calculations based on the forces known to exist in materials at the molecular and crystalline levels always lead to strengths which are two or three magnitudes higher than the strengths obtained in service or in the laboratory. It has been a major problem, therefore, to explain: (a) How fracture can occur in compressive stress states. (b) Why the observed strength of a material is always much lower than its calculated strength.

Jan 1, 2012

Mine drainage and mine reclamation are topics of major interest to the mining industry, federal and local governments, and the general public. This publication and its companion three volumes are the proceedings of a conference held in Pittsburgh, Pennsylvania, April 24-29, 1994. There were twelve sessions (69 papers) that dealt with mine drainage, including modeling, geochemistry, prediction, treatment, control strategies, characterization, hydrology, and case studies. These sessions comprise volumes 1 and 2. The six sessions (34 papers) that dealt with reclamation and revegetation of disturbed lands are included in volume 3. Volume 4 includes the six sessions (34 papers) that dealt with such topical issues as fires at abandoned mine sites, subsidence, hydrology, mine wastes, and policy. Poster session presentations are represented by 49 papers and 92 abstracts that have been placed in the back of volumes 2, 3, and 4, consistent with the subject of that volume.

Jan 1, 1994

By Michael Zachariah, Art Miller, David Kittelson, Gib Ahlstrand

This report describes an investigation in which we used iron-doped diesel fuel to generate metal-bearing diesel particles and a subsequent analysis of the particles using transmission electron microscopy (TEM) and energy-dispersive spectroscopy (EDS). For this study, DPM was generated by a 1.5-L diesel engine and the fuel was doped with ferrocene to enhance the level of iron in the system. The exhaust particles were collected on TEM grids and analyzed using the Philips CM12 TEM/EDS instrument. Results show that when the iron-to-carbon (soot) ratio (Fe/C) in the engine is low, the exhaust particles have morphologies similar to those for the undoped case, but at a threshold Fe/C value of 0.013 (for this engine), homogeneously nucleated metallic nanoparticles are formed and begin agglomerating. The number and size of these nanoparticles increase with level of doping. Metal-bearing particles that span a wider size range are also formed. Agglomeration of metallic and carbon particles is observed in two distinct modes: attachment of iron primary particles (5–10 nm in diameter) to carbon agglomerates, and coagulation of iron agglomerates (20–200 nm in diameter) with carbon agglomerates. Results of this work imply that as new engine technologies reduce soot levels in the engine and/or levels of trace metals in the fuel are increased, the generation of metallic nanoparticles may ensue, creating a potential health concern. Keywords: Nanoparticles; Particulate emissions; Metallic particles; Metal emissions

By M. Leva

WITH the development of new processes for the production of synthetic liquid fuels, an extensive literature search was undertaken to uncover fundamental relationships between fluid and heat flows and the operating variables of new types of converters. Examination of published correlations revealed that considerable uncertainty existed in the correlation of the operating variables of such equipment with the pressure drops which could be expected through packed and fluidized systems; correlations proposed in the literature differed from each other frequently by as much as 75 to 100 percent. Because new processes, especially more recent modifications of the original Fischer-Tropsch process, must compete with old, firmly established processes on the basis of unit product cost, the pressure-drop correlations in the literature were considered to be too inaccurate for use in calculating the energy required to pass fluids through packed beds. The following study was begun in 1946 to develop correlations that would be suitable for the design of new equipment in which fluids are brought into contact with granular materials. To arrive at general relationships, systems were chosen that did not involve chemical reactions, and a, particular effort was made to give the correlations only in terms of quantities that are ordinarily available from general process and design specifications.

Jan 1, 1951

By Harry W. Campbell

A Bureau of Mines investigation identified no mineral deposits in the Lost Creek RARE II area. Sand and gravel has been mined from alluvial flood plain deposits just outside the RARE II boundary. An oil and gas lease application which includes the eastern portion of the RARE II area is pending. Abundant basalt in the area can be crushed and used as aggregate; but it could not compete with similar deposits in more favorable locations, or with cheaper substitutes such as volcanic cinders or sand and gravel which are available outside the study area closer to major markets. No indication of coal or geothermal energy resources was found. INTRODUCTION Location and Access The Lost Creek RARE II area encompasses 8,300 acres (3,400 ha) of Lassen National Forest in north-central California, about 20 mi (30 km) north of Lassen Peak. The closest city is Redding, California, 50 air mi (80 km) southwest. Peripheral access is provided by State Highway 89 passing near the western RARE II boundary (fig. 1). The Pacific Crest Trail traverses the western margin of Hat Creek Rim adjacent to the eastern boundary of the area.

Jan 1, 1983

By Rimas Pakalnis, Doug Milne, Marc Ruest, Lewis Martin

Whereas many researchers and mine engineers have conducted tests on cable bolts using various grouts, water: cement ratios, and physical modifications of the cable to determine the load-carrying characteristics ofa bolt, few studies have been conducted on cable bolts fitted with internal instruments. Those studies that have been done have concentrated on cable response averaged over significant (6.1 m) cable lengths. Researchers at the Spokane Research Laboratory (SRL) of the National Institute for Occupational Safety and Health in Spokane, WA, are investigating the physical properties of cable bolts by replacing the conventional king wire with a modified king wire on which strain gauges have been installed. A numerical analysis was performed to match laboratory results. Loads calculated by the model were then compared to loads measured in the laboratory on 1.83-m-long cables grouted into two 0.91-m-long pull-tube assemblies. Load along the cable was monitored with 20 strain gauges installed along the length of the cable. This paper documents test results on these modified cable bolts. The instrumented cable bolt provided reproducible point measurements of cable load as opposed to load measurements averaged over long cable lengths. Such point measurements can assist in interpreting the influence of cable confinement, grout quality, rock mass stiffness, and other factors. The instrumented cable bolt is a practical field and research tool because it can predict point loading along the cable. The instrument has been successfully field tested at FMC's Granger Mine, Granger, WY; the Meikle Mine, Carlin, NV; the Stillwater Mine, Nye, MT; and the Getchell Mine, Golconda, NV. By monitoring load and displacement of the rock mass using these instrumented bolts, more-effective ground support can be selected and installed, which will lead to safer working conditions for miners.

Jan 4, 2004

By Z. T. Bieniawski, Benjamín Celada

After emphasizing the importance of quantitative rock mass classifications in mining, originally directed to selection of rock support measures, but subsequently to estimates of rock mass properties such as rock mass strength and rock mass modulus of deformation, current attention calls for a classification specifically for rock mass excavability by tunnel boring machines (TBMs), which are used extensively in tunneling as well as in the mining industry. This paper introduces the Rock Mass Excavability (RME) index for predicting excavability of rock masses by TBMs using a quantification of machine performance and rock mass conditions. The RME index is based on five input parameters aimed at relating rock mass behavior and machine characteristics: (1) uniaxial compressive strength of the rock material, (2) drillability/abrasivity, (3) rock mass jointing at mine drift face, (4) standup time of the excavation, and (5) groundwater inflow. Development of the RME index entailed the collection of extensive data from more than 28 km of tunnels and some 400 case records from projects in Spain involving double-shield TBMs. In the process, a number of statistical correlations have been established between RME and such output parameters as degree of machine utilization, advance and penetration rates, thrust and torque of the cutterhead, and the specific energy of excavation. It was found that the RME index provides a particularly significant correlation for predicting the average rate of advance (m/day). In essence, the RME index is a classification system that features interaction of rock mass conditions with boring machine characteristics for use in the early stages of a project. It should be noted that the RME index does not replace the Rock Mass Rating (RMR) or Q-systems as used in mining and tunneling; indeed, one of the RME input parameters, standup time, is determined from the RMR. However, the approach presented introduces a specialized tool relevant to excavating tunnels and drifts. Possible applications to hard-rock mining are explored.

Jan 5, 2007

By James M. Link

A program was initiated tinder sponsorship of the U. S. Bureau of Mines to investigate pipeline behavior of raw and spent oil shale slurries. Slurries were recirculated in pipeline loops with 150-mm and 200-mm diameter horizontal test sections and a 150 -mm diameter vertical test section. Slurry concentrations from 10 to 60 weight percent were investigated. Critical and deposition velocities were observed. Head losses were measured at various velocities. Rheology measurements were made on representative homogeneous samples from the pipeline. From these data, pipeline energy requirements were predicted by computer and compared to pipeline data. Computer programs were also used to analyze pipeline data for two flow models: 1. Heterogeneous flow regime for coarse, settling slurries 2. Homogeneous flow regime for nonsettling suspensions The economics of slurry transport of raw and spent shale were examined. Cost estimates encompassed a range of pipe diameters to transport a wide range of throughputs of both raw and spent shale. Similar estimates were made for conveyor belt systems to provide a valid cost comparison. Economic comparisons are valid in a general sense, but a specific study must be made to determine the cost advantages of hydraulic transport for a given mine.

Jan 1, 1977

By Alex C. Smith, Thomas A. Gray, Lynn M. Crayne, Michael A. Trevits, Phil Glogowski

Mine fires constitute one of the greatest threats to the health and safety of those working in the underground environment and each event has the potential for disastrous consequences. Of the major mine fires and thermal events that have occurred in the United States in the last 6 years, it is estimated that remotely installed seals could have been used in 63% of the events to control fire growth or to aid in fire suppression work. The National Institute for Occupational Safety and Health (NIOSH) is conducting full-scale tests at the NIOSH Lake Lynn Experimental Mine to evaluate and improve remote mine seal construction technology. The main focus of this work is to develop reliable technology that will completely close the mine opening from floor-to-roof and rib-to-rib. This paper presents the results of remote seal installations using grout-based materials.