Search Documents

By Clifford H. Summers

This report describes an experimental program which we conducted on behalf of the U. S. Bureau of Mines, to select from currently available materials two novel systems of construction for air-restraining bulkheads to be used in control of radon-polluted air in underground uranium mines. The program included both laboratory and field tests, the latter conducted in a portion of an operating mine owned and operated by Union Carbide Corporation at LaSal, Utah. The test site was a worked-out, double entry stope having a Volume of about 2000 cubic meters, and was located immediately adjacent to an exhaust airway. The bulkheads were constructed of 15 cm x 1.5 cm timber uprights, 5 cm x 15 cm horizontal members supporting a close-fitted 13 mm plywood curtain-wall., which was covered with a low-permeability membrane to seal in the radon-polluted air. The two membrane materials selected for testing were chosen from a list of twenty-two potentially acceptable candidates using criteria such as strength, flammability, ease of application, adhesion, radon permeability, and elasticity. Thirteen of the candidates were tested in our laboratories for adhesion to plywood and to both wet and dry concrete (simulating wet and dry mine rock surfaces), and for their general physical properties, including radon permeability. The final selections made by the Technical Project Officer, and based on our recommendation, were a pre-formed ethylene propylene diene monomeric rubber (EPDM) membrane 1.12 mm thick, normally used as a roof sealant in industrial construction, and available from Carlisle Tire and Rubber Co., Division of Carlisle Corp., Carlisle, PA, and Aquafas 48-00, a water-based mastic used in a wide variety of commercial applications and available from H. B. Fuller Co., Foster Products Division, Spring House, PA. The EPDM membrane was applied as a single sheet, laminated (dry) between two layers of plywood, and the Aquafas was applied both by troweling and spraying onto a plywood surface. In the field test, radon concentrations were continuously measured before, after, and in the trapped air behind each bulkhead. Temperature, pressure, and velocity of the air in the adjacent airway were also measured and recorded continuously. Radon fluxes at the rock/air interface and through the bulkheads themselves were measured manually on a frequent basis. All continuously acquired raw data were recorded automatically on two USBM Data Aquisition Systems (DAS), and the raw data were converted into engineering units and recorded on magnetic disks by a specially programmed microcomputer that was interfaced with the DAS's. Relatively clean (i.e. low radon concentration) air was pumped into a point near the face of one test bulkhead from a location 170 meters away through vent bag. Several air curtains and two air-restraining bulkheads were erected in passageways adjacent to the test area in an effort to control both velocity and radon concentration of the air flowing past the bulkhead faces. An average concentration of approximately 500 pCi/liter at a flow of 550 m3/minute was attained as the background concentration against which leakage through the bulkheads was measured. The entire field test period extended from October, 1981 to March, 1982, a total of six months, and was subdivided into seven successive time periods: 1) site preparation 2) background measurements prior to bulkhead construction 3) passive restraint, with bulkheads in place and totally sealed 4) open bleeder period of natural convection ventilation in and out of the bulkheaded area through a 10 cm (diameter) opening, with connecting tubing; leading into an Exhaust airway 5) open bleeder period, having forced exhaust through a 1.0 cm opening using a servo-controlled fan 6) charcoal trapping period, using the servo-controlled fan to exhaust air through the charcoal traps, to test the effectiveness of such traps in removal of radon from the exhausted air 7) site decommissioning Each of the two systems tested, one incorporating the pro-formed EPDM-rubber membrane and the other utilizing Aquafas 48-00, was assessed for effectiveness in controlling radon-polluted air by observing the change in the radon concentration in the ventilation air flowing continuously over the surface of each bulkhead. The sensitivity of the observed measurements was limited by the volume flow-rate of the ventilation air and the radon concentration in that air. The data would indicate that the observed increments in radon concentration in the ventilation air moving across bulkheads B-l and B-2 were essentially zero within the limits of sensitivity of the measurements. Data from radon flux measurement taken both on the sealed ribs adjacent to the bulkheads and on the bulkheads themselves did not differ significantly from blank data.

Jan 1, 1982

By A. R. T. Denues

"INTRODUCTION The Explosives Division of the Bureau of Mines, United States Department of the Interior, is investigating cushioned blasting at the Explosives Testing Station, Bruceton, Pa. The general interests of this investigation are practical and relate particularly to safety. The immediate concern is an application of cushioned blasting in coal mining.In cushioned blasting, various means are employed to reduce the intensity of the application of energy in an explosive action in a borehole. The primary object is to increase the efficiency of the use of explosives. Cushioned blasting is designed to save the energy usually lost in excessive shattering and in this way to effect economies and to produce increased proportions of desirable lump coal. That this saving should lead to greater efficiency is indicated by an analogy with the theory and experience of size-redaction by crushing or grinding from which it is known that a large proportion of the energy consumed is expended in producing the smaller sizes (26),3/. Aside from these considerations, increasing the yield of lump coal is important in practice because larger sizes of coal usually sell at higher prices. Some statistics published in England in 1934 (63) illustrate the economic origin of the interest in increasing yields of lump coal; these indicate for three sizes of coal that as the size decreases the value decreases in the approximate series 3:1.5:1, thus:"

May 1, 1940

By C. W. Morris

The continuous miner training system provides classroom materials training aids, and a continuous miner simulator to provide a short, intensive instruction and skills development program for training or retraining continuous miner operators. This project included refinement of training objectives, revision of training aids, improvements to the simulator, and evaluation of the entire system. This report describes the revised classroom materials and the validation of the training system.

Jan 1, 1982

By P. B. Grote

The report is concerned with the issue of the possible transfer of U.S. and other developed country deep ocean mining (DOM) technologies to developing countries. This subject is one of several major issues in current UN Law of the Seas negotiations. As background to the subject, the report provides a detailed critique of the various terms and conditions pertaining to technology transfer in recent negotiating texts. It also provides a description of the relevant DOM technology, sources of innovation, and methods of proprietary protection. Functional requirements for viable technology transfer are developed and used as a basis for the definition of alternative levels of programs and implementation approaches, including required changes in the negotiating text. The consequences of these technology transfer options on the various parties are investigated.

Jan 1, 1978

By Douglas F. Scott

Zinc, silver, copper, and tungsten are the principal minerals in Dardanelles RARE II area (No. 4982). Zinc with associated silver and copper occurs in a persistent shear zone in metasedimentary rocks and in a massive sulfide vein; tungsten occurs as disseminated scheelite in a tactite zone along a metasedimentary-intrusive rock contact. Since 1883, approximately 100 lode mining claims have been recorded, mainly it the eastern portion of area No. 4982 (fig. 1). Extensive workings on the Alhambra Prospect indicate past production; however, no records were found for the prospect. At the Alpine Mine, 500 tons of tungsten ore had been mined before 1943 (Hopson, 1943, p. 1) and possibly 1,000 tons of tungsten ore mined by 1947 (Benson, 194/, pp. 2).

Jan 1, 1982

By James Noll, Sam Janisko

Underground miners are exposed to some of the highest levels of diesel particulate matter (DPM) in the United States. Therefore, it is important to monitor the exposure of miners to DPM, but it can be difficult because of the complex composition of DPM and the number of interferences. Currently, elemental carbon (EC) is used as a surrogate because it makes up a significant fraction of the DPM and is not affected by interferences. Standard measurement methods for EC can be time consuming and only record end of shift results. In this research, a laser absorption technique that enables one to measure EC concentration in near real time was shown to be a beneficial tool. The real time data showed that the fresh air being drawn into a stone mine was not properly reaching the working area and needed to be redirected to decrease DPM concentrations. The real time data also provided a more accurate efficiency ofan environmental cab compared to just using the standard method by detecting the opening of the cab's window and door. The EC optical monitor was also worn by researchers in a mine to show how it can give not only the average concentration for the shift but also reveal when and where a miner is exposed to DPM. Keywords: Laser absorption, diesel, elemental carbon, mining, exposure

By K. C. Dean

Discarded automobiles represent the greatest single resource of reusable metals, plastics, and rubber in the United States. This report presents results of Bureau of Mines research, conducted from 1965 to 1983, on separating and recovering useful materials from the scrapped hulks, using old and new metallurgical techniques combined with standard scrapyard methods. The Bureau determined the materials composition of three composite cars designated as circa 1960, mid-1970's, and early 1980's, and used these cars to study smokeless incineration and hand-sorting techniques. In studies on treating rejects from automobile shredders, the Bureau designed a process that included air classification, water elutriation, magnetic separation, handpicking, and heavy-medium separation, and also investigated cryogenics and liquation. Complete recovery of cop-per and other metals was economically made by hand and tool dismantling, leaching, or selective melting of starters and generators. Techniques are also discussed for plastic recovery and waste tire treatment.

Jan 1, 1985

By Francis E. Federspiel

Silver and gold are the principal metals in the study area; they occur in quartz veins or silicified portions of shear zones. In some deposits, lead, antimony, zinc, and molybdenum are associated with gold and silver. A uranium-bearing buried stream channel lies near the southern boundary. Since 1850, more than 300 lode claims and relocations have been recorded mainly in the southeast corner of the study area (fig. 1). Complete mine production records are not available; however Clark (1977, p. 28) reported less than $300,000 of gold and silver were produced, mainly from the Exchequer, IXL, and Pennsylvania Mines. Other mines in the area probably yielded are before 1900, but early records are not available.

Jan 1, 1981

By G. L. Oldright

This paper is the fourth of a series of preliminary papers on smelting in the lead blast furnace.4 The objects of this investigation are to determine the conditions obtaining within the blast furnace by direct experimentation and to correlate these conditions with operating factors, furnace behavior, and metallurgical losses. ACKNOWLEDGMENTS The authors wish to express their appreciation to the management of the International Smelting Co. at Tooele, Utah, for their whole-hearted cooperation in this investigation.

Jan 1, 1929

By G. P. Houston

This is the final, report submitted for the Contract No. H0220002 with the U. S. Bureau of Mines for the design and development of a Permissible Automatic Data Acquisition System (PADAS) to measure and record roof stresses in underground mines Basically the PADAS is a portable, battery powered, 24-channel data acquisition system designed for safe unattended operation of up to 30 days duration in explosive environments. The unit will accommodate twenty-four pressure transducers or eight borehole deformation gages (or any combination) at distances up to 300 feet from the PADAS to measure pressures up to 10, 000 psig. All 24 channels as a selected group are scanned sequentially at one of several selectable rates.

Jan 1, 1973

By Robert L. Lagace

A whole-mine experiment to assess the practical feasibility and utility of the dedicated-wire technique for overcoming poor trolley carrier phone system performance at a large underground coal mine was designed, performed, and evaluated. The technique involves the use of a single, low-loss, properly terminated and branched auxiliary wire placed in the rail haulageway. This auxiliary dedicated wire allows signals to electromagnetically couple to the trolley wire/rail transmission line, and thereby significantly decrease the overall signal attenuation rate on the trolley wire/rail line. The in-mine dedicated-wire demonstration program and its results, conclusions, and recommendations are described. The dedicated-wire technique is shown to be a valid and practical one for significantly improving carrier phone system performance in coal mines.

Jan 1, 1981

By Sidney Katell

Philippine laterite and serpentine ores can be utilized in an electric furnace operation to produce both a steel ingot and a ferronickel product. Figure 1 is a schematic interpretation of a plant in which laterite and serpentine ores are processed separately to obtain both ferronickel and steel as products. A relationship of estimated capital requirements and probable returns has been established in this study for a plant of this type. No attempt has been made to evaluate the risks involved in commercial operations. At such time that the project might be constructed and placed in operation, changes in the costs of material, labor, and power may materially affect the profitability aspects of this study. One of the uncertainties involved in the economic evaluation is the cost of mining, handling, and shipping the ores. It is on this basis that the cost of ore delivered at the plant is assumed to be variable at $3, $5, and $7 per net ton (dry basis). For all other costs a plant site at Iligan City, Philip-pine Islands, has been assumed in preparing the economic characteristics for a plant that will process 2,000 tons4/ of ore per day. Results of the study, for the 2,000-ton plant, with all monetary values expressed in terms of United States currency (Philippine peso valued at $0.50), are summarized as follows:

Jan 1, 1962

By K. E. Stanfield

[Asphalt ~~d road oil ar8 the principal products manufactured from Wyor.1in~ Ilblack oilo" \r,hich, beca.use of th?lir hig.~ E\.sphal t and hig} sulfur COi.1Jce~1t, .!?re difficult e':ld costly to refine into hi?;h-gra.de motor f 101s, burning oils. and lucri ants by presont mothods. Accordin~ly. the demand for truHle asphaltic renidl urn for the construction of roade aJ1.d other uses is 3. controlling factor in the quantity of crud~ oil prod ICed. The increasiilg -u.tilization of special aST>ha.lts as ine}""Pensive bonding, in-]

Jan 1, 1941

By H. P. Rue

The Bureau of Mines has recently collected two samples of crude oil from wells in the Greasewood Flat area of northeastern Colorado. Sample 31310 was taken from the Continental Oil Co.'s well Briggs No. 1 which care in or September 27, 1931, with a maximum production of 940 barrels per day. Sample 31311 was taken from tie Reiter-Foster Oil Co. Is well Ida Johnson No. 1 which came in on August 24, 1931 with a maximum production of approximately 1000 barrels per day.

Jan 1, 1932

Electrical trailing cable used to power coal mining machinery is frequently damaged by tensile strain or crushing by mining machines running over the cable. A major problem is finding the exact location of a short or open in this cable so it may be repaired. A major problem is finding the exact location of a short or open in this cable so it may be repaired. FMC Corporation was awarded modification III to USBM Contract H0122011 to continue development and testing of cable fault locators, resulting in delivery of: 1. A prototype electrostatic/electromagnetic/ TDR transmitter and an electrostatic/electro-magnetic receiver sot that: o Locates cable faults by time domain reflectometry o Locates opens by detecting electrostatic signals o Locates shorts by electromagnetic coupling. 2. A prototype infrared detector and an infrared detector power supply that heats a shorted area by applying high current (at low voltage) and locating a short by infrared output. 3. Twelve production infrared detectors. 4. Detail drawings for all of the developed instruments.

Jan 1, 1973

LARGE-SCALE production of zirconium by the Northwest Electrodevelopment Laboratory of the Bureau of Mines at Albany, Oreg., is an anomaly that justifies some explanation. The reduction of titanium tetrachloride with magnesium in an inert atmosphere, as perfected by Dr. W. J. Kroll before 1940, aroused renewed interest in zirconium, and in 1945 development work on this metal was initiated at Albany under Dr. Kroll's technical direction. Preliminary results were promising, and in February 1947 a pilot plant with a weekly capacity of 60 pounds of zirconium-metal sponge was put in operation. Shortly thereafter the Oak Ridge National Laboratory of the Atomic Energy Commission requested production of 1 ton of zirconium-metal sheet, with the provision that it have a low hafnium content. The Bureau of Mines was furnished with a. supply of Brazilian baddeleyite ore, containing less than 1 percent hafnium with respect to zirconium, from which was made about. 2,700 pounds of relatively low hafnium zirconium sheet of 0.080-inch thickness for test purposes. This was accomplished by melting zirconium sponge in a graphite crucible, hot-rolling the ingot in an iron sheath, and finishing by cold rolling. Concomitantly the Oak Ridge Laboratory developed a method for separating hafnium from zirconium; and, in cooperation with the Atomic Energy Commission and the Bureau of Ships of the Department of the Navy, a, larger pilot plant was erected to produce zirconium from very low hafnium zirconium tetrachloride furnished by the Commission. Pilot-plant work on producing zirconium tetrachloride from zircon sand and baddeleyite was discontinued. Production of zirconium sponge in the larger pilot plant of 500 pounds per week capacity was begun in June 1949.

Jan 1, 1956

By Douglas F. Scott

In 1981 the U.S. Bureau of Mines and U.S. Geological Survey conducted a mineral survey of the Pyramid RARE II area (No. 5023) covering 23,500 acres (9,500 ha) of E1 Dorado National Forest and 7,900 acres (3,200 ha) of the Lake Tahoe Basin Management Unit (fig. 1). The Bureau of Mines investigation did not reveal mineral deposits in the area. Samples taken from silicified and limonite-stained metasedimentary rocks and aplite dikes were void of precious or base metals or uranium. Placer samples from stream gravels contained no gold values. Molybdenite occurs in quartz stringers within quartz monzonite near Grass Lake, adjacent to the area; no extension; were found in the area.

Jan 1, 1982

By J. E. Hipp

Three electrostatic field sensing proximity warning devices were tested using full-scale cranes and power line systems, a scaled model facility, environmental testing facilities, and theoretical/numerical analysis. The design objective of each device is to assist in safe crane operation near overhead power lines. Several design deficiencies (varying from device to device) were observed, including inadequate overlap in sensitivity ranges, utilization of vacuum tubes and electro-mechanical parts, temperature sensitivity and inaudible alarms. In addition, the testing showed major device limitations including sensitivity to boom orientations and length, polarization dependent responses, and unreliable operation in the presence of multiple power line circuits. The multiple power line circuit problem is intrinsic to electrostatic sensing devices. The remaining deficiencies and limitations are correctable within a state-of-the-art design. This investigation is not intended to evaluate the safety aspects or policy of utilizing proximity warning devices. Rather, the purpose is to determine the performance characteristics of such devices in relation to the criteria specified in proposed MSHA regulation 77.805-4 (i. e., the devices must alarm at a distance of 10 feet from the power line).

Jan 1, 1980

By Slavoljub D. Maksimovic

The Bureau of Mines, through a memorandum of agreement with the State of Ohio, tested a method of constructing seals in abandoned mine openings in Ohio by means of pneumatic stowing of crushed limestone and gravel with sand. A total of five openings and one shaft were back-filled. Pneumatic stowing uses compressed air to convey material through a pipeline and into the mine opening. The stowing equipment consists of a power supply, a blower, a feeder to inject the material into the pipeline through an airlock, and a nozzle for directing the placement. Material is ejected from the nozzle at high velocity, creating a high-compaction fill upon impact. Well-graded aggregate up to 2 inches in diameter and having sufficient fines is used as fill. The stowing method is safer and faster than conventional methods, is cost competitive, prevents trespass into abandoned mine openings, and eliminates or reduces the exposure of workers to possible hazards since the discharge nozzle can be kept at the mouth of the opening. The equipment is mobile, and, with some modification, the technique could be widely used for sealing abandoned and active mine openings, even in remote locations and during severe weather conditions.

Jan 1, 1982

By E. D. Gardner

Placer mining is the mining and treatment of alluvial deposits for the recovery, of their valuable minerals. The method has been used principally for mining gold, but a large proportion of the world's production of tin, platinum, and diamonds and other gem stones and minor quantities of other heavy minerals have been won in this manner. In the United States, as in the world at large, gold has been the principal mineral obtained by placer mining. Minor quantities of metals of the platinum group are recovered with the gold in some localities. Important quantities of sapphires have been produced at placer mines in Montana, and tungsten minerals have been obtained on a commercial scale from placer deposits in California and Colorado. Other heavy minerals or gem stones, however, have not been mined to any important extent by this method in the United States. The search for placer gold and the working of the deposits when found have had much to do with the early development of the West. Placer mining has been gradually overtaken and surpassed in importance by lode-gold mining, until in 1932 less than a quarter of the country's total gold production was from placers or about an eighth, excluding Alaska. In 1932 about 76 percent of the placer gold produced in the United States was recovered by dredging. Although other forms of placer mining still are important, they have been declining for many years, as the richest and most readily mined deposits of gravel along the stream courses have been exhausted. During 1931 and 1932 there was a revival of small-scale mining, but few new deposits were discovered.

Jan 1, 1934