Search Documents

By G. R. Hopkins

The average heat requirement per barrel of crude processed in the United states rose from 555,000 B. t. u. in 1939 to 579,000 B. t. u. in 1940, although crude runs increased from 1,237,840,000 barrels to 1,294,162,000 barrels in that period. Thus the almost invariable rule that the average amount of heat needed to refine a barrel of crude oil declines when total crude runs to stills increases was broken. (See fig. 1.) The reasons underlying the apparent loss in fuel efficiency in 1940 are quite obscure. There is little question but that the principle of heat exchange, the most important fuel saver, was used as extensively in 1940, as in 1939. A few companies replaced purchased power with electricity made at their plants, but for the country as a whole purchased electricity increased 7 percent, as compared with a 5-percent gain in crude runs to stills. Furthermore, the premise -the more complex the products the more fuel required -does not hold, as the yield of ?complex" products, including gasoline, declined in 1940.

Jan 1, 1942

By Richard Rittenhouse

This program was to develop a new base line system for automated continuous room and pillar type mining. The primary requirement estab¬lished for this machine is that the machine be capable of mining and bolting simultaneously. Additionally, this machine was to provide temporary and permanent roof control, have a productive - full - face semi-automatic mining system, leave a clean entry outby the machine, provide maximum operator protection, provide effective dust suppression and provide air scrubbing to restrict respirable dust to permissible levels. The machine has effectively demonstrated the ability to mine and bolt simultaneously. Additional above ground operation, testing, and time studies are recommended to further verify the machines abilities. Design improvements are recommended for future generation AES machines. These relate to marginal design areas such as side loading on vent duct lift cylinders, etc., that will not impair additional testing of the existing machine.

Jan 1, 1983

By H. L. Riley

At the Southern Experiment Station, Tuscaloosa, Ala., reports are prepared from time to time on results of washability studies of coal from important beds in the Southern Appalachian region. The investigations that provide the material for these reports are made by the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and the mine operators. The principal objective of a washability study is to obtain technically and commercially important data to aid in determining the best methods for preparing and utilizing the Nation's reserves, particularly of coking coals. Such information is also important from the standpoint of conservation, because it facilitates the selection of preparation methods that will yield an acceptable product with a minimum loss of coal to the rejects.

Jan 1, 1958

By Karl C. Dean

All components of 15 automobiles manufactured between 1954 and 1965 were analyzed, and it was determined that a representative junk automobile would have the following composition (all figures in pounds): steel, 2,532; cast iron, 511; copper, 32; zinc, 54; aluminum, 51; lead, 20; rubber, 145; glass, 87; miscellaneous, 142. Time and motion studies and a cost evaluation were made to determine if such a typical vehicle could be economically burned in a smokeless incinerator and hand-dismantled, and if the resultant steel could be baled into a high-quality No. 2 bundle containing less than 0.10 percent copper. The cost evaluation showed that processing the composite car would cost about $51 to produce about $56 worth of marketable ferrous and nonferrous metal products and provide an annual rate of return on investment of 19 percent.

Jan 1, 1969

By R. S. Dean

"Interest in the nitrogen content of steel has increased sharply in the last few years. Investigations have indicated that its presence in steel has an important bearing on high temperature brittleness3, magnetic properties4, room temperature hardening5, and shock resistance. The steel producer may therefore look forward with certaintly to the necessity of controlling this element in a considerable proportion of his product. The literature, however, reveals a great many contradictory statements concerning the percentage of nitrogen which must be present to produce given effects on the properties of iron and steel. Most of these arise from a misunderstanding of the nature of the iron-nitrogen diagram near the iron end and a lack of recognition of the effect of state of aggregation on physical properties although both have been fairly well worked out.My thanks are due to Mr. J. L. Gregg, Prof. R. H. Dowdell, Mr, R. F. Mehl and Mr. H. C. Vacher for suggestions in connection with the preparation of this paper, and to Mr. C. H. Hefty and Mr. G. T. Motok for furnishing a valuable bibliography and translations of articles by Must and Duhr.The iron-nitrogen diagram in the solid state, so far as it concerns the nitrogen content of commercial iron and steel, consists simply in a solubility curve increasing with temperature. The important thing about this solubility curve is that without cold wore the iron nitride when precipitated does not go into solution on heating for long periods below 300°C. This slowness of solution is probably due to the fact that iron nitride when present as a separate phase has at these temperatures an equilibrium pressure of several thousand atmospheres7 and that therefore each particle of iron nitride surrounds itself with a layer of nitrogen. The precipitation of such an unstable crystal presents points of interest thermodynamically but we can not go into these here. It is quite well established that it precipitate. It can not diffuse then unless this layer is broken through or the temperature and pressure are increased to a point where the nitrogen is absorbed at an appreciable rate in the surrounding iron. This rate will depend on the degree of unsaturation of the iron and the excess pressure of the nitrogen above equilibrium pressure. The degree of unsaturation is determined by the temperature alone so that the temperature at which the rate of solution of the nitride becomes appreciable will depend on the pressure of nitrogen developed. This, in turn, will depend on the balance between rate of decomposition of the nitride and the rate o: flow of the iron. In annealed iron, this temperature of appreciable solution rate is between 300 and 350°C.8 By cold work, however, the elastic limit of the iron is increased, and conditions for the nitride to go into solution are reached at a much lower temperature, giving rise to the so-called blue brittleness. This brittleness and hardening is due to iron nitride going into solid solution and is not precipitation hardening."

Mar 1, 1931

By Albert H. Fay

The first data compiled by the Bureau of Mines relating to coal- mine accidents in the United States were published in Bulletin 69," in which the total fatalities by years and States were tabulated from 1896 to 1912. Since the publication of Bulletin 69, further research has been conducted, with the result that the bureau is now able to publish for the first time all of the fatal accidents described in the State inspectors' reports by States, causes, and calendar years, from the beginning of inspection service to date. For the anthracite mines of Pennsylvania, there is a continuous record since 1870; the records of the Pennsylvania bituminous mines are continuous from 1877, and, with the exception of one year, the Ohio records are complete from 1874 to date. In fact, the records of all of the States, with few exceptions, are complete; and incomplete data for any year may generally be attributed to the fact that no report was published during that year. The magnitude of the coal-mining industry in the United States is such that too much stress can not be placed on the need of safeguard- ing the three-quarters of a million men employed. Although the figures given herein show an appalling record for past years, they are not published for the purpose of proclaiming the high fatality rate of the past. They are a record of experience covering a period of 45 years, showing causes and results of many accidents in the coal mines of the United States. They represent a diagnosis of the hazard of the mining industry, pointing out the principal physical causes of accidents, and make available a body of uniform facts that will serve as a basis of preventive measures for use in future operations. It is with these great purposes in view that the Bureau of Mines presents the classified data in this report. Classification and study of mine accidents on the basis of number of persons killed is common and very old, but fails to throw enough light upon the problem involved. Many serious accidents in mines have no fatal results, hence in a tabulation of fatalities they are overlooked and the real hazard of the industry is not made clear. An accident does not necessarily include an injury that may result therefrom. Such accidents as the breaking of a hoisting cable, an explosion of powder, gas, or dust, a runaway car or motor are all serious. Although no loss of life results, they should be recorded, investigated, and studied to prevent their repetition. No accurate data for the United States are available showing how far the personal element as related to the miner and his co-worker, the mine foreman, or to the superintendent and others in authority, contributes to accidents. Many accidents are due to inexperience on the part of the miner, his failure to heed orders, a misunderstanding of instructions and last, but not least, carelessness of himself or his fellow worker. A foreman or superintendent may fail to give proper warning regarding the conditions of certain parts of the mine; he may not have inspected certain rooms or entries on the day of a mine accident; the mine may not be properly equipped, or the operator may neglect to comply with the inspector's recommendations. There is, therefore, a personal element on the part of both the operator and the miner that must be considered. Legislation and the enactment of compensation laws will make the operator realize the seriousness of the mine-accident situation, when fatalities and injuries are to be paid for in legal tender of the realm. The miner must be educated and made to realize the dangers he encounters; he must learn that self-preservation and the safety of his fellow workmen should receive his first attention; he should cooperate with his employer, his asso- ciates, and the State mine inspector to the end that the mine hazard may be reduced to a minimum. "Cooperation for safety" should be the watchwords of the operator, miner, State inspectors, and all others in any way interested in the mining industry.

Jan 1, 1916

By Marcel Vanpee

Eight extinguishing powders KCI, were tested on five types of diffusion flames. The effect of flame temperature on the inhibition efficiency was investigated by varying the oxygen index of the flame supporting atmosphere. Inn addition a spectrographic investigation of powder flame dissociation products was carried out on the methane/air/ABC (NH4H2PO4) flame. Dissociation products for this flame included P0, PH, NH, and Na. It is concluded that the main factor to be considered in the efficiency of tie powder is the flame temperature Purple K (KHC03) was typically inefficient in low temperature flames and very efficient in high temperature flames. On the other hand, ABC (NH4H2PO4) was found to lose its efficiency at high temperature but to be quite efficient in the low temperature flames. The effect of temperature is offered as an explanation of the poor efficiency of Purple K (KHC03), against coal dust explosions as contrasted to the high efficiency of phosphate salts against coal dust explosions.

Jan 1, 1982

By William N. Hale

This Bureau of Mines report gives a detailed study of water usage in the Montana mineral industries, along with projections for the future. The mineral industry of Montana in 1963 used 36.5 billion gallons of new water, and reused or recirculated an additional 53.5 billion gallons for a total water requirement or usage of 90 billion gallons. The petroleum industry was the major water user, followed by the copper and zinc industries. Many mineral industry operators provide their own water, and new water is withdrawn largely from surface sources. At present, sufficient water is available in rivers, streams, and reservoirs in Montana; however, shortages do exist locally near mineral industry operations using large quantities of water. Some is supplied from sources up to 44 miles distant. New water withdrawn by the State of Montana mineral industry is expected to increase from 36.5 billion gallons in 1963 to 51.1 billion gallons by the year 2000. The total-water requirement is expected to more than double, or reach 182 billion gallons by the year 2000.

Jan 1, 1966

By William N. Hale

This Bureau of Mines report gives a detailed study of water usage in the Montana mineral industries, along with projections for the future. The mineral industry of Montana in 1963 used 36.5 billion gallons of new water, and reused or recirculated an additional 53.5 billion gallons for a total water requirement or usage of 90 billion gallons. The petroleum industry was the major water user, followed by the copper and zinc industries. Many mineral industry operators provide their own water, and new water is withdrawn largely from surface sources. At present, sufficient water is available in rivers, streams, and reservoirs in Montana; however, shortages do exist locally near mineral industry operations using large quantities of water. Some is supplied from sources up to 44 miles distant. New water withdrawn by the State of Montana mineral industry is expected to increase from 36.5 billion gallons in 1963 to 51.1 billion gallons by the year 2000. The total-water requirement is expected to more than double, or reach 182 billion gallons by the year 2000.

Jan 1, 1966

By L. G. Marshall

This report describes dredging and processing of sand and gravel from a glacial-fluvial deposit in the Raccoon River valley near West Des Moines, Iowa. Preliminary cleaning and separation of the sand and gravel at the dredge site with subsequent transportation to separate plants and the production and disposal of the various grades of aggregate material are also described. The geology of the deposit is summarized. A tabulated summary of costs in units of labor, power, and supplies is included.

Jan 1, 1963

By J. W. Town

The Bureau of Mines determined the physical properties of southeastern Idaho phosphate fines as related to mineral composition, particle size and liberation, beneficiation, and potential use in structural clay products. The phosphate mineral in the fines was identified by unit-cell dimensions to be essentially the same as the phosphate mineral fluorapatite identified in the coarser sizes. The mean particle frequency as determined by electron-microscopy and pipet-analyses was between 0.5 and 0.2 micron. Liberation of the phosphate could not be definitely determined because of the weathered condition of the minerals and their extreme fineness. No beneficiation scheme was developed that would concentrate the phosphate into a marketable fertilizer product; therefore, forming and firing tests were made to demonstrate that the fines can be used to manufacture structural clay products.

Jan 1, 1968

Two coal seams were selected and the conceptual designs were based on the geological and physical conditions typical of these seams. As a result of the screening process presented below, the two coal seams selected were the Lower Kittanning Seam in central Cambria County, Pennsylvania and the Pittsburgh Seam in northwestern West Virginia and southwestern Pennsylvania. SELECTION PROCESS FIRST SCREENING OF LONGWALL OPERATIONS The list of longwall operations prepared in Phase I and included in the Phase I report, was used as the basis for a first screening. From this list it was determined which longwall operations were not in the Appalachian coal fields and not in a coal seam of the thickness range of 42 to 72 inches. The first screening eliminated 30 of the listed operations, leaving 48.

Jan 1, 1976

By James M. Spear

The U.S. Bureau of Mines conducted a mineral survey of the Domeland Addition (5207) and Woodpecker (5206) RARE II areas during the summer of 1979. These study areas were examined to determine the presence or absence of mineral resources and reserves and where possible, to estimate values. The study areas are 9 air mi northeast of Kernville, California, and encompass 47,400 acres of primarily granitic rocks of the Sierra Nevada batholith with some scattered exposures of older metasedimentary, volcanic, and metavolcanic rocks. These other rock units partially surround the exposed batholith in the Domeland Wilderness and consist mostly of late Paleozoic quartzites, mica schists, marbles, and meta-volcanics, Mesozoic quartz diorite and gabbro intrusives, and local Tertiary basalt and andesite flows.

Jan 1, 1981

By O. M. Schaus

This paper is one of a series, prepared by the Bureau of Mines and deals with the Montreal mine, one of only two active properties in Wisconsin on the Penokee-Gogebic range. The purpose of this paper is to describe the conditions of occurrence of iron ore in a particular property and to present sufficient details of equipment and production methods to convey to the unacquainted operator a correct idea of the mining practice.

Jan 1, 1930

By F. A. Penning

An experimental and analytical investigation was conducted on a recoverable pit bottom buffer. Work was conducted at the Colorado School of Mines using the U.S. Bureau of Mine-s free fall test tower. The four-sided butter, one of several designs by Cable Belt Ltd., was constructed of reinforced rubber slabs. The kinetic energy of falling weights, 1670 to 6000 lb, was absorbed by the flexure of rubber slabs loaded along their edge. A series of constant energy, 3000 ft-lb and maximum design velocity, 600 fpm tests were conducted. Static testing of the buffer established the load-deformation behavior. A large hysteresis loop plotted above and below the data published by the manufacturer. Creep was evident during; the loading Lend unloading cycle. Electronic instrumentation measured deceleration using your accelerometers; overall and intermediate movement was found from four displacement transducers; bending strains were recorded at four locations; and base reactions were measured by using four load cells. Data were recorded on tape and played back on a recording oscillograph. High speed movies were taken of all the tests. Symmetry of response and rebounds, when they occurred, were noted. From the displacement-time and load-time data, maximum decelerations were calculated by four methods and different assumptions. Good agreement was found from these approaches. Impact loads ranged from a low of 0.7 to a high of 6.1 gs. A dynamic computer model was written for the response of the buffer. Displacement-time, and acceleration-time plots show close correspondence with experimental data for the ten experiments. Data from accelerometers, displacement transducers, strain gages, and load cells are included. The computer program listing, and displacement-time acceleration-time plots are also presented.

Jan 1, 1980

This work presents: 1.) the results obtained from measurements of temperature profiles in pillars and at working faces of three coal mines located in Colorado and New Mexico, 2) a comparison of the experimental results with theoretical predictors based on linear heat flow models, and 3) temperature profile predictions based on a two dimensional coal mine model with an inclined crack located in the roof or wall of the opening. The thermal properties of the coal and shale samples taken from the mines were used as input data for the computer model. Good agreement was found between the measured profiles and the theoretical values obtained with the one dimensional model. The two dimensional model results show that a visible crack (0.01-0.07-ft thick) in a coal roof causes a surface temperature difference from 0.2 to 1°F at the edge of the crack for rock exposed to air from 1 hr to 288 hrs and with the air to rock temperature differences from 2°-6°F. A temperature difference of 0.3 °F was found between solid and broken rock in a shale roof with a 0.03-ft thick crack inclined 45° to the horizontal after a ventilating time of 48 hrs and the air to rock temperature difference of 2.1°F.

Jan 1, 1972

By Dipak Sengupta

This study analyzes the safety, technology, and economic impact of eliminating safety fuse from metal/nonmetal mines, based on operation and manufacturer experience over the past five to ten years. If safety fuse is eliminated, blasting accidents will decrease with no technical impact except for some limited, specific applications. The economic impact will be minor for large operations, but will be significant enough for small operations that some small operations will likely close rather than change. The majority of the mines would probably change over, with the extra cost absorbed by the market. Elimination of safety fuse would have obvious impact on the two manufacturers of safety fuse; one manufacturer already produces an alternative system, and will remain unaffected; the other will be affected if they do not change their production strategy. There will be a very minor effect on the mining industry as a whole due to abolishment of safety fuse from the standpoint of employment or production.

Jan 1, 1980

By Ronald Branstetter

Gaseous and particulate exhaust emissions from 20 diesel engines in service at five underground mines were measured with high accuracy instrumentation. The engines that were tested were checked for faults or maladjustments. The vehicle and engine maintenance organization was studied at each mine and an idealized maintenance program was devised. Faults were induced in a new diesel engine to determine their effect on the characteristics of the exhaust emissions. The results, conclusions and recommendations from this investigation are presented in this final report.

Jan 1, 1983

By J. R. Nettle

The purpose of these studies by the Federal Bureau of Mines was to determine the feasibility of refining low-grade hafnium by an inert-gas-shielded molten-salt electrorefining technique to produce a hafnium metal meeting reactor specifications. The techniques were adapted from those used success-fully for titanium electrorefining. Three electrolytes containing hafnium chlorides were developed from which deposits having a Brinell hardness of 170 or below were recovered. A KC1 + NaC1 + HfC14 electrolyte produced deposits in the hardness range of 140 to 165 Brinell. Deposits with a hardness range of from 132 to 152 Brinell were pro-duced from an electrolyte composed of KC1 + LiC1 + HfC14. A third electrolyte composed of NaC1 + K3HfC17 produced deposits with a hardness as low as 139 Brinell. In a fourth electrolyte, composed of NaC1 + K2HfF6, a measure of refining was accomplished, but under the test conditions no metal meeting specifications was recovered; none was softer than 174 Brinell. A number of metallic impurities were reduced in quantity by the electro-refining process, notably iron, which normally was reduced from 250 p.p.m. to less than 50 p.p.m. Magnesium generally was reduced from 680 p.p.m. to less than 80 p.p.m. Manganese content was also reduced by the electrorefining process. Sponge containing 90 p.p.m. Mn yielded deposits containing a maximum of 50 p.p.m.; some deposits contained only 10 p.p.m.

Jan 1, 1961

By W. T. Benson

The Bureau of Mines has undertaken investigations to examine selected deposits of beryllium throughout the United States. The beryllium deposit about 6 miles southeast of Lone Pine in the Owens Valley region of Inyo County, Calif., was among those selected for study. In 1960, field work was conducted on the Inyo Beryl claim to determine the extent and character of the beryl-bearing deposit. This report describes the work that was done. In the area investigated, the beryl occurs disseminated in granite and limestone and as stringers. Apparently, the stringers are related to nearby pegmatite dikes, inasmuch as some appear to contain fine-Grained pegmatite. Granitic rocks enclose most of the stringers, which occur as fracture fillings, ranging from thin seams to 4 inches in thickness. The stringers are of muscovite, quartz, albite, and beryl. Some also include epidote and fluorite. For the most part, they are widely spaced. Therefore, mining of substantial tonnages averaging better than 0.2 percent beryl does not appear feasible.

Jan 1, 1962