Search Documents

By Donald R. Alvic

For electric utilities serving the aluminum smelter industry in the United States, sulfur oxide (SOx) abatement legislation could bring about increases in the costs of generating electricity. This paper documents the method and assumptions used in estimating these increases, and the contains the results of the estimation. 1.2 SMELTER INFORMATION The smelters used in this study were identified by the Bureau of Mines (BOM) and are listed in Table 1.1. Also included in Table 1.1 are the electric utilities that serve these smelters. Compliance costs were estimated for these utilities. Some of the utilities are unique in the way that the information is handled or in the way the utility is operated; these are discussed below. 1.2.1 Big Rivers and Associated Co-ops, Data for Big Rivers and Associated Co-ops were gathered by George Mason University (GMU) students for BON and are included in this study.

Jan 1, 1988

Provide long-term measurement of mine sidewall closure in backfilled stapes subject to flooding. Approach A water resistant extensometer is made by enclosing a rod-actuated transducer in a telescoping tube which is enclosed within an oil-filled outer housing. How It Works To assemble a water resistant extensometer, a cylinder -shaped transducer and two support rings are pushed into the small-diameter section of the telescoping tube where the transducer is held in place by friction. The outside of the small-diameter section of the telescoping tube is then greased and slid into the slightly larger-diameter section. See drawing. The cylinder-shaped transducer contains a potentiometer whose actuating arm is attached to a stainless steel extension rod that passes through one end of the telescoping tube. A similar rod is attached to the opposite end of the transducer body, and extends through the other end of the telescoping tube. A coil spring inside the large diameter end of the telescoping tube extends the tube

Jan 1, 1978

By Robert M. Doerr

The research objective was to determine the effect of aluminum alloy additions on the oxidation behavior of cobalt-nickel alloys. Thirty high-purity alloys were reacted with 02 at 0.5 atm at 1,351°, 1,389°, and 1,429° K in a volumetric apparatus for about 300 min. The alloy compositions consisted of Co-Ni master alloys (0, 22, 50, 70, 91, and 100 wt pct Ni) with aluminum additions of about 0, 1, 2, 4, and 8 wt pet. Large early deviations from, or changes in, the parabolic rate constant were encountered, but in most cases, the reaction rate declined approximately in accordance with the parabolic rate law. A sharp peak in the parabolic oxidation rate constant was observed for specimens containing a to 22 percent nickel and 1 to 2 percent aluminum at 1,351° K, and the rate constants for these compositions were lower at the higher temperatures. Specimens containing 8 percent aluminum reacted far more slowly than did any of the others.

Jan 1, 1971

By R. V. Ramani

The industrial hygiene and safety aspects with internal combustion engines in mining systems is truly interdisciplinary and encompasses many fields such as mine ventilation, exhaust gas and particulate analyses, mine atmospheric environment monitoring, mathematical modeling of generation, dilution and dispersion of pollutants in ventilation systems, and engine testing and approval. This bibliography, therefore, is a compilation of references from interdisciplinary sources pertaining to diesels and related areas. Related areas are defined as those concerned with: (i) mine ventilation system design and operation; (ii) description, measurement, modeling and monitoring of mine atmosphere contaminants, and (iii) tests, standards, selection procedures, and operational practices for internal combustion engines in underground mines. References cited from source materials span the years 1900 to early 1977. Total number of references cited is 511. Subjective criteria governed the definition and selection of references. Therefore, this bibliography is not claimed to be all-inclusive nor does it purport to be an exhaustive search of all sources.

Jan 1, 1977

By F. W. Wood

The use of consumable.-electrode arc melting as a production technology is growing. One advantageous feature of this process is that it avoids ingot contamination by soluble crucible materials by employing a chilled metal crucible. Because the thermal balance under these conditions is rather delicate and does not necessarily provide a favorable environment for solidification, catastrophic imbalances can occur. The effectiveness and mechanistic roles of various factors are mostly unknown, and more intelligent insight regarding the distribution of temperature and heat is needed. Experience has provided several pertinent observations, some of which are quite superficial. The most meaningful data have resulted from studies of molten pool shapes and sizes and from measurements of heat flow through crucible walls. Overall experience, intuitively interpreted and supplemented, is sufficient nevertheless as a basis for a boundary-value treatment of the problem. A mathematical analysis based on a separation of variables, using conventional differential equation methods, provides a useful solution. For a cylindrical ingot, the temperature varies as a Bessel function of an argument proportional to the radius and as an exponential function of longitudinal position. Trial calculations using the problem solution seem to verify the general correctness of the result as compared with experience. The role and nature of solution parameters are also clarified, though not entirely resolved. It is revealed that the barrier to heat flow at the ingot-crucible surface has a prominent influence. Utility of the model embodied in the problem solution is readily demonstrated by considering a variety of contemporary questions about arc melting, and it is hoped that utility can be enhanced by improvement of the model.

Jan 1, 1968

By Herman O. Ankenbruck

Analyses of statistical data indicate that haulage accidents are one of the largest sources of injuries and fatalities in underground coal mines, and that the rate of accidents in transportation has been increasing during the past few years. These previous analyses were performed by correlating accident or fatality data at a rather high level of miner activity. In this present investigation, underground surveys were made by observing conditions and activities in some detail at a rather low level of activity in an attempt to understand factors contributing to hazards in the specific situations observed. The aim of the current study was to derive preventive measures that might obviate the hazardous conditions and unsafe acts observed; and, following this, to provide recommendations for additional research and development to reduce accident potential in underground transportation. The major project tasks are diagrammed together with the task outputs in figure 1-1. Initially, a preliminary study of ell underground haulage operations was performed in order to establish the kinds of data needed and to provide the rationale leading to the data requirement. At the same time, the various types of haulage equipment used for each operation were defined. A preliminary analysis of each type of haulage operation was performed in order to establish the sequence of tasks required to operate haulage equipment. These tasks were transferred directly onto observation forms, and were used in developing interview forms. In parallel with the task analysis, a review was made of accidents and hazards that might occur during each type of operation.

Jan 1, 1975

1.0 Control House (DWG. NO. 56-401-G) - 1.1 Physical Description The Control House is a single story, 2728 square foot building with an adjacent transformer yard. A four foot overhang provides shade protection for the walls. The building is heated and air conditioned. The HVAC System has an elevated outside air intake and provides a positive pressure environment within the structure in order to prevent the infiltration of heavier-than-air, noxious gases. The materials of construction are as follows: Structure : Light-Gage Metal Framing Exterior Walls :Outside - Preformed, Metal Siding :Inside - Insulated Metal Liner Panels Interior Partitions :Gypsum Board over Light-Gage Metal Framing Roof :Insulated, Preformed Metal Panels Ceilings :Mechanical & Electrical Rooms - Exposed underside of Roof Panels Control Room, Lunch Room, Toilets, Entry - Suspended Acoustical Lay-In Tile Floors :Mechanical & Electrical Rooms - Concrete Slab on Grade Control Room, Lunch Room, Toilets, Entry - Resilient Tile Exterior Doorsand Windows :Preformed Metal Panel Manufacturer's Standard Units

Jan 1, 1979

By C. B. Manula

This report is volume 5 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation, and ventilation. This volume of the final report describes the Subsidence subsystem of the Master Design Simulator. This subsystem uses the finite element method to simulate ground movement caused by an advancing mining face in an underground coal mine. The model is structured around the concept that the ground mass is a layered media of different thicknesses and material properties. Gob areas are considered to be unfilled with broken rock at the beginning of mining. After mining starts, the gob areas are filled with broken material which provides resistance to the lowering of the overlying strata. The model is tied to the Geology and Reserves subsystem, but it can also operate as a free standing routine. A case study is presented illustrating the application of the model. A detailed user's manual, including a program listing, is included in the appendices.

Jan 1, 1974

By J. B. Czirr

MESA Corporation has completed a four-year program for the Bureau of Mines to develop a technique for measuring roof competence in underground coal mines. The preferred technique employs a tracer gas that is injected into a roof borehole drilled near the working face. The tracer gas performs the dual purpose of determining the pressure loss rate from the borehole and of marking the diffusion pattern of the the escaping gas. The primary detection technique relies upon observation of the rate of pressure drop in a hole drilled in the roof strata under test. If this measurement indicates a significant probability of roof collapse, the gas diffusion pattern is outlined with the Leak-gun tracer-gas detector. These two techniques provide a comprehensive method for predicting the relative probability of roof collapse in operating coal mines.

Jan 1, 1985

By Robert Merritt

Approximately 2,500 tons of low-grade uranium ore were used to conduct a field-scale heap leaching test as well as throe column leach tests. The ore used to construct the field-scale heap leaching test had a grade 0.023% U308 while the ore used fur column leach tests had a grade of 0.027% U308. The ore was crushed to minus 4 in. The field-scale heap was constructed on a clay base with parallel effluent lines running under the heap spaced 7.5 ft apart. The heap was leached for 45 days, drained, washed, and dismantled. Based on residue analysis, approximately 205 tons of ore were leached with a final U308 extraction of 96%. The heap was 17.9 ft in height and leached in a near-vertical pattern down to approximately 1 ft, at which point the leached zone become bell-shaped. Two 8-ft column charges and one 18-ft column charge were leached for 36 and 45 days, respectively. Based on residue analyses, all U308 extractions were greater than 96%. The conclusions generated by the studies showed that (1) flow rates were similar for column leaching and field-scale leaching, (2) final U308 extractions were the same for both types of leaching; however, the deeper ore beds tended to require longer leaching times, and (3) the reagent requirements were reduced with increased bed depth.

Jan 1, 1980

By Laurance L. Oden

The Bureau of Mines is developing melting data for binary combinations of the alkaline earth fluorides and yttria to facilitate the formulation of slag compositions. The present report deals with the CaF2-Y203 system for which solidus and liquidus temperatures and solid solubilities were determined. The information is presented as the phase diagram. All specimen compositions were blended from high-purity materials and encapsulated in Mo or Pt20Rh prior toheat treatment. Liquidus temperatures were determined by ceramographic examination of heat-treated and quenched specimens. Solidus temperatures were determined by differential thermal analysis and by electron microprobe analysis of quenched specimens. Terminal solid solubilities were derived by parametric methods. The peritectic system was found to be pseudobinary due to the formation of yttrium oxyfluoride at temperatures near the liquidus. The peritectic point occurs at 7 mole pct Y203 and 1,438° ± 5°C. The terminal solid solubility of Y203 in CaF2 decreases from 7 mole pct at 1,438° C to 1 mole pct at 1,100° C, and the solubility of CaF2 in Y203 decreases from 9.5 to 7 mole pct over the same temperature interval.

Jan 1, 1970

By Michael S. Miller

In 1987 and 1988, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 3,100-acre Borah Peak Wilderness Study Area (10-047-004) and a 708-acre parcel adjacent to the north in order to evaluate their identified mineral resources. The study area is located in Custer County, ID, about 18 mi northwest from MacKay. The study area lies along the western foothills of the Lost River Range and is underlain by quartzite, sandstone, shale, argillite, dolostone, and limestone. The Lost River fault, a major active fault, lies along the length of the study area. Large alluvial fans spread out from valleys originating east of the study area.

Jan 1, 1989

By C. W. Davis

This paper is the second of a series of progress reports on a study, of the hydrometallurgy of manganese which is being conducted in an endeavor to make possible utilization of the large deposits of low-grade domestic manganese ores that occur in several States. There are at least four processes in which a knowledge of the action of SO2 gas on manganese oxides at elevated temperatures may prove of value. One ,of these involves dissolution of manganese from ores. The Bureau of Mines has investigated the hydrometallurgy of manganese by a process in which SO2 gas, a waste product at many smelters, is passed into water to form a solvent for manganese. Although Several manganese minerals acre readily dissolved, rhodochrosite (MnCO3) was attacked but superficially.§. Recent experiments have shown that a roast at 650 to 900°C converts the manganese of rhodochrosite to a form that is quickly dissolved by a weak SO2 solution. Introduction of smelter gases containing as much as 5 per cent SO2 during such a roast would not add much to the cost of the operation and might result in the formation of considerable water-soluble manganese sulphate.

Jan 1, 1930

By F. A. Penning

This report describes the development of skip and guide desings for vertical shafts in deep vein mines. Skip and guide systems for bottom dump skips are identified as being used in current practice. Mine visits were made to obtain current information on the needs and problems of operating mines. Methods of structural and mechanical analysis of skip bodies and bails are outlined. A dynamic computer model was written to find the dynamic interaction between skips and guides for guides with geometric misalinements. A materials evaluation section identifies currentavailable and applicable materials that can be used effectively for new skip construction. Guide materials are also presented. Analysis includes the economies resulting from streamlined buntons and from low skip payload ratios. Selection of materials is based on strength, abra¬sion and corrosion resistance. Design requirements related to the shaft environment are presented. Consideration for the selection of guides and buntons is also given. Conceptual design includes the concept of cylindrical skips, center-seeking guide rollers, and asymmetric bail design to decrease dynamic interaction. An outline for field tests is presented. Future research areas are: testing, guide geometry measure¬ment, advanced suspension, dynamics, and structural configurations.

Jan 1, 1977

By W. M. Dressel

In producing feed for a lead blast furnace, concentrates analyzing 70 to 80 pct Pb are sintered to produce a physically acceptable low-sulfur product which contains only about 50 pct Pb. Mixtures of PbS with varying amounts of SiO2, CaO, Fe 20., and ZnS were heated in an oxidizing atmosphere at 1,000° C; the products were cooled and examined to determine the problems involved in producing sinter with substantially higher lead levels. Microscopic and electron microprobe studies of the above products as well as experimental and commercial sinters indicate that sinters consist essentially of lead silicates, lead-zinc silicate, calcium zinc silicate, and spinel (ferrite). Lead oxide and lead sulfate areas appear to result from insufficient mixing of the materials prior to sintering. The data give an insight into the process and show that sintering results from a complex interaction of all constituents and that sintering is not simply a matter of diluting the mixture to control the oxidation of lead sulfide.

Jan 1, 1975

By S. K. Mathur

This report identifies all the possible activities, variables and factors that contribute to the surface subsidence process over room and pillar workings. These factors are responsible for mine instability and collapse that ultimately transforms into surface subsidence. Such a failure mechanism is initiated by the failure of the mine floor bed and or the failure of the pillars or the failure of the roof after second mining, which eventually brings down the roof. The individual responses of the pillar, floor and roof rocks to the mining induced stresses and the complex interaction between these components can't be attributable to any single factor. Also, no attempt has been made to quantify the significance of each of these factors and relate to the ground subsidence due to the lack of field data. The discussion here is centered primarily on the first mining though second mining is mentioned very briefly,

Jan 1, 1982

By Marshal Scherba

Coal seams approximately 7 feet, 9 feet and 20 feet thick at depths of 250, 600 and 1,000 feet respectively were detected using high resolution seismic reflection techniques. Investigation of seismic profiles indicates that good data are required to delineate faulting with only 20 feet of throw but that faulting with 50 feet of vertical displacement can be detected with poor data. Data acquired from dynamite charges fired in water saturated media were clearly superior to that acquired using charges dry tamped in 10 and 20 foot holes.

Jan 1, 1977

By S. Malhotra

Processes for the recovery of manganese contained in low-grade domestic sources are evaluated. Conclusions are based on analysis of literature, technical evaluation and cost analysis. The Nossen Nitric Acid Process, the Sulfuric Dioxide Process rind the Ammonia Leach Process should be developed further as they offer the hunt opportunity for commercialization.

Jan 1, 1984

By David A. Lipton

U.S. Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine the mineral resources and potential of the Moses and Dennison Peak RARE II areas in Tulare County, California. These areas, along the west slope of the Sierra Nevada, are underlain by grarnitic rocks of the Sierra Nevada batholith and contain numerous metasedimentary roof pendants. Silver, copper, and zinc occur in contact-metasomatic deposits within the metasedimentary rocks. In the Moses area, the Powell Mine (fig. 1) contains an estimated 90,000 tons (82,000 t) of subeconomic silver, zinc, and copper resources. The King Solomon Prospect has 3,000 tons (2,700 t) of silicified phyllite containing zinc. On the Helen-Joyce Prospect, 44,000 tons (40,000 t) of gossan occur above a poorly exposed silver-zinc rich zone. Potential exists for additional mineral resources and occurrences at each of these properties.

Jan 1, 1983

By Bernard Baum

Combined preservative/fire retardant systems were pressure impregnated into Douglas fir and Ponderosa pine samples and evaluated for decay, flammability, and mechanical properties. The objective of the evaluation was to identify cost-effective systems for use with mine timber, and to provide an information and data base from which Federal code regulations could be established. Thirty systems, based on combinations of commercially available preservatives and fire retardant impregnants and coatings, were applied to Douglas fir samples and evaluated for decay and flammability. The ten most promising systems were ap¬plied to both fir and pine and reevaluated for decay and flammability before and after water leaching. The five best systems were given a thorough laboratory evaluation using both pine and fir. Evaluations included flame spread, smoke density, toxic gases, decay, compressive strength, flammability after artificial weathering, and cost. All systems had acceptable toxic gas levels and smoke densities, but flame spread was only borderline acceptable for most of the samples tested. A trade-off analysis showed Acid Copper Chromate/Fyrprufe with Albi-107A/144 intumescent paint and Koppers NCX to be the-best systems. Recommendations are made for further large-scale testing using the two best Systems.

Jan 1, 1978