Search Documents

By W. Petruk, M. J. Matos

An aplite ore from Guarda in northern Portugal, containing albite, microcline and quartz and muscovite gangue was studied to identify conditions for extracting the feldspar minerals. The large amounts of quantitative mineralogical data needed to evaluate grinding behaviour were provided by automated image analysis. The images were acquired on polished surfaces by measuring back-scattered electron signals produced with a microprobe. Minerals were identified from X-ray spectra and discriminated by grey level and element-characteristic X-rays. The quantities and size distributions of the minerals were determined by measuring thin sections of unbroken ore to predict the grind required to liberate the feldspars. The ore was then ground to -1.7 mm, polished sections were prepared from sieved fractions and the quantities of mineral species and apparent total liberation were determined by analysis. The predicted and measured liberations were compared and the grinding behaviour of the ore interpreted. In an appended correction, the correct version of Equation 1 is represented and Tables 3 and 6 are revised to consider all size fractions, including those coarser than 300 micrometres, in calculating the total liberation from King's fractional liberation

Jun 18, 1905

By Mavor S.

Further discussion at the Mining Institute of Scotland's general meeting held in Edinburgh, 12 February 1916, with D.W. Mowat, president, in the chair, of a paper published in Trans. Inst. Min. Engrs., 1915, vol. L, p.625 and discussed vol. L, pp.92, 433, 468, and 704 included comments by Mowat D.W. and the author's reply

Dec 1, 1916

Paper presented at the Mining Institute of Scotland's annual general meeting held in Glasgow, 8th April 1916. Although there is nothing novel or difficult about the sinking described, circular shafts are not numerous in Scotland so the details connected with such a sinking may be of interest. The shaft was sunk at Dykehead Colliery, Larkhall, which has been worked for over 50 years from the upper seams. It became necessary to sink another shaft to serve as a replacement downcast, by which the output might be maintained and some of the lower seams won. As the sandy clays regularly caused bulging into the rectangular shaft and sinking of the surrounding ground it was decided to make the new shaft circular and to enclose its mouth in a foundation-block of concrete resting on the solid clay. Details are given of the sinking, brick seating and lining, kettle strike, water-rings and doorhead lintels as well as the permanent fittings, winding gear and the cages themselves

Dec 1, 1916

By A. J. Naldrett

"Synorogenic mafic intrusions are a common feature of the northern Appalachians. Two sulphide-bearing intrusions in central Maine that have been investigated revealed a number of important features that illustrate sulphide-silicate interaction that relates to magmatic sulphides. The Moxie Pluton is a large mafic intrusion emplaced during the Devonian Acadian orogeny. The Katahdin gabbro is a small mafic body that is probably genetically and temporally related to the Moxie Pluton. Both intrusions were formed bv the intrusion of variably fractionated magmas into irregular chambers and feeder zones. The southern half of the Moxie Pluton contains three small sulphide accumulations, whereas the Katahdin gabbro hosts a large, predominantly massive, sulphide body. Textural evidence clearly documents the magmatic origin of these sulphides.The three Moxie Pluton sulphide bodies are located at or very close to the intersection between the intrusion and the sulphidebearing Hildreths Formation. Sulphur assimilation, suggested by this relationship, is supported by the isotopically light (634S = —8 to —25) and the selenium-poor (S/Se - 25 000-48 000) character of the Moxie sulphides and correlation with the Hildreths Formation sulphides (S34S = —25, S/Se = 25 000-48 000). Isotopically light sulphur (534S = —20 to —21) and high S/Se ratios indicate that the majority of sulphur in the Katahdin sulphide body was also derived from an unexposed country rock source. The volume of sulphide in this example illustrates the potential efficiency of the sulphur assimilation process—so efficient in this case that marked dilution of the economic chalcophile elements resulted from the addition of so much external sulphur.The three Moxie Pluton sulphide occurrences are all impoverished in Ni and Cu (1.87-0.44% Ni; 0.72—0.32% Cu in massive sulphide), but contain normal Co contents (0.22-0.13%) relative to typical magmatic sulphides. The Katahdin sulphides show a greater Ni and Cu impoverishment (0.2% Ni; 0.1% Cu in massive sulphide) with similar Co (0.17%). The Ni content of the Moxie Pluton olivines document the fractional removal of sulphides during crystallization of the host magma, which resulted in the progressive depletion of the chalcophile metals in this magma. Modelling that involved the fractional crystallization of the magma coupled with the fractional removal of a specified proportion of sulphide has successfully duplicated the Moxie Pluton sulphide compositions. A similar magmatic model has been postulated for the Katahdin sulphides with a greater degree of sulphide fractionation. This latter model is again supported by extremely low Ni/forsterite ratios in olivines, though the compositional range is insufficient to document fractionation. These magmatic models are not unique, but they provide a relatively constrained and consistent explanation for the sulphide compositions.The Ni contents of olivines are the most important indicator of sulphide-silicate interaction in mafic magmas and have exploration potential. They provide a means of assessing the timing and extent of sulphur saturation in an intrusion and are a guide to the Ni content of a sulphide accumulation in equilibrium with olivine. In the Maine examples they provide strong evidence of the magmatic origin of the sulphide accumulations and justification for magmatic modelling."

Jan 1, 1984

By Tuncel M. Yegulalp, Selamet G. Ergelebi

A description is given of a method of analysing modern mining systems in terms of reliability and their effects on productivity. Non-exponential distributions, such as the Weibull and lognormal distributions, for failure and equipment repair times are also considered. The resulting non-homogeneous Markov process is solved by the method of stages. A longwall mining system is analysed as an example.

Jan 4, 1993

By P. R. Ineson, D. W. James

For a criterion to be useful it must either demonstrate directly the role of exhalative processes in the formation of a deposit or describe a unique attribute of exhalative deposits. Few of those employed in previous investigations entirely satisfy either condition. The limitations of three of the most frequently employed criteria are illustrated by studies of the geology of the King Island Scheelite deposit in Tasmania.

Jan 12, 1993

By C. M. Lesher, R. R. Keays

"The komatnte-associated Fe-Ni-Cu sulphide mineralization at Kanihalda, Western Australia, is generally believed to be magmatic in origin, but a number of postmagmatic processes significantly modified the original distribution, structure, texture, mineralogy and chemistry of the ores. Two important types of mobilized magmatic sulphides are interpillow/interbreccia sulphides and hydrothermal vein-type sulphides. Interpillow and interbreccia sulphides occur interstitial to pillowed or volcaniclastic footwall metabasalts beneath or adjacent to the stratiform contact ore horizons. They are mineralogically and compositionally similar to massive ores (and are similarly depleted in PGE relative to the compositions of bulk samples of mined ores), but normally do not contain the distinctive chalco-phile ferrochromites characteristic of contact ores. They are interpreted as magmatic sulphides that have been mobilized from the overlying or adjacent massive sulphide layer during peak tectono-nietamorphism.Hydrothermal sulphide-quartz + albite veins also occur in the footwall metabasalt and contain unannealed deformation fabrics indicative of emplacement during retrograde metamorphism. The high Ni and Pd contents of these sulphides (7-13% Ni, up to 70 ppm Pd) indicate that the metals have been derived from the spatially associated komatiites and/or contact ores, consistent with the Pd depletion previously inferred for massive ores. Very low Ir contents and high Pd/Ir ratios of the vein-type sulphides confirm an aqueous transportation-deposition mechanism; hydrothermal transfer of PGE results in strong decoupling of Pd from Ir.There appears to be a complete continuum of sulphide mobilization at Kambalda ranging from whole-scale phy sical dislocation (fault offset ores) and selective mobilization (stringer sulphides) through nietamorphie replacement (interpillow/interbrec- cia sulphides) to jiydrothermal dissolution and redeposition (vein-type sulphides)."

Jan 1, 1984

By Ruddle R. W.

Magnetite occurs in the reverberatory furnaces, blast furnace and converter (a) as the result of its presence in the materials charged, and (b) as the result of oxidation of the FeS in the charge in the absence of sufficient SiO2 to slag the FeO as it is produced and thus prevent its subsequent further oxidation. Magnetite is reduced by FeS according to FeS+3Fe3O4=10FeO+SO2 and similar reactions. This reaction is markedly affected by temperature and does not proceed to any important extent below about 1200°C. To ensure comparative freedom from magnetite it is therefore necessary to raise the temperature of the furnace to the highest practicable figure and to use plenty of siliceous flux. Since the maximum operating temperature is likely to be limited by the resistance of the refractories to attack by the slag, investigation of the factors affecting this attack should be helpful. It is reasonable to suppose that the formation of magnetite might be minimized by ensuring intimate admixture of matte and slag during conversion so that silica is readily available for combination with ferrous oxide as the latter is formed. The literature gives no clue to the importance of this factor and some experimental work on this aspect might be fruitful

Jan 1, 1953

By D. W. Holliday

The major deposits of anhydrite and secondary gypsum in Jamaica occur discontinuously at a single horizon within the Lower Eocene succession of southeast Jamaica. They are not intruded from other horizons of different age, as has previously been supposed. The gypsum and anhydrite occur in a regressive sequence at the junction between marine (Richmond Formation, Halberstadt Volcanics, Halberstadt Limestone) and overlying non-marine (Wagwater Formation) sediments. They are thought to have been formed in an arid supratidal (sabkha) environment. A variety of 'nodular' structures occurs in the gypsum and anhydrite which can be related to early diagenetic processes and compaction effects. All gradations exist between single isolated anhydrite nodules and structureless anhydrite due to closer packing and coalescence of nodules. The structures and textures in the anhydrite are thought to be consistent with penecontemporaneous formation from gypsum crystals rarely more than 2 cm in diameter. Single anhydrite nodules are not usually larger than 2 cm; nodules of greater size are compound, due to the coalescence of several smaller nodules. Some large compound nodules may have developed from single sand crystals or rosettes. Compaction of anhydrite appears to have been largely mechanical, but some rocks have an aligned fabric, suggesting later flowage

Dec 1, 1971

By J. Ivon Graham, T. D. Jones

This paper presents methods in use in British coal-mines for the suppression of dust. While the effect of present-day treatment will not be apparent for several years, in pits in South Wales, concentrations as high as 50 gm./1,000 cu. ft. were some years ago fairly common in various operations at or near the coal-face, with an average concentration of 20 gm./1,000 cu. ft. Now the average concentration in what were previously dusty pits is probably not greater than 3 gm./1,000 cu. ft.Nevertheless, every effort must be made to improve conditions still further. In South Wales it is claimed that 99% of the coal-faces requiring treatment have been dealt with either by wet cutting, infusion, or hand-spraying. The extent of the treatment by these methods can be gauged by the fact that the total length of coal-faces now being treated by water infusion in Cardiff and Swansea areas is about 33,000 yds., by wet cutting 25,000 yds., and by hand-spraying nearly 14,000 yds. The influence of methods of mining upon dust production is only mentioned very briefly in this review, and there is no doubt that much more is to be learned concerning this aspect. It can be stated, however, that good mining practice is essential to prevent unnecessary dust production, and the problem of dust in mines will be solved only by the closest co-operation between mine managers, workmen, and scientists.

Jan 1, 1947

By P wade

This is the first Presidential Address given to the Nottinghamshire Branch of The Institution following the merger of the Nottinghamshire and North Derbyshire Branch of The Institution of Mining Engineers (IMinE) and the Midland Branch of The Institution of Mining Electrical and Mining Mechanical Engineers (IMEMME). I intend to review the formation of the individual institutions as well as what has been achieved by mining related institutions over the years and finally I intend to look to our future.

Jan 11, 1996

"The Archaean komatiite-associated nickel sulphide deposits at Kambalda, Western Australia, exhibit a number of stratigraphic features that are indicative of a strong volcanic control on ore localization, including (1) a restriction to specific basal cumulate metakomatiite host units, (2) confinement within distinctive synvolcanic embayments in the footwall and (3) variations in the internal structure and composition of overlying and adjacent barren metakomatiite flow's and the distribution of interflow metasediments with proximity to the ore zones.The high magnesium content of the host units (up to 45% MgO volatile-free) in comparison with that of aphyric or spinifex- textured lavas (16-32% MgO) has been considered previously to indicate either magmas/lavas rich in intratelluric olivine or selective accumulation of olivine phenocrysts. The marked linear trend of the oreshoots, basal host units, footwall embayments and the volcanic stratigraphic relationships have been used as evidence for local linear feeding fissures. Rare relict igneous olivine in some host units is, however, demonstrably not intratelluric, and there is no direct or indirect evidence of a proximal eruptive site (e.g. footwall feeders, pyroclastic breccias, ultramafic intrusives) at Kambalda such as at some other deposits of this type. Kambalda is interpreted as a distal rather than proximal volcanic environment.Emplacement of the komatiite sequence at Kambalda was probably controlled by the locations of a few specific eruptive sites relative to regional topographic gradients and influenced by the topography of the pre-existing volcanic surface. Olivine enrichment in the basal host units occurred by in-situ fractionation and cumulus crystallization of olivine during longitudinal lava flow within linear lava conduits, possibly centralized on depressions between non-overlapping footwall basalt flows. The distinctive stratigraphic relationships are attributed to localization of lava conduits along the volcanic pitchline, flanked by more slowly moving parts of the flows. There are analogies with the physical volcanology of Modern basaltic and Proterozoic komatiitic lava flows.A corollary of this model is that the lava conduits thermally eroded and assimilated sulphidic sediments, contributing additional sulphur to sulphur-saturated komatiites or possibly inducing sulphide separation in originally sulphur-undersaturated komatiites. The latter would account for the restriction of ores to linear cumulate komatiite host units (thermally active lava conduits) and the locally mutually exclusive, but stratigraphically equivalent, relationship between the ores and sulphidic metasediments at Kambalda."

Jan 1, 1984

By D. J. Allan, W. R. Wilson

For conventional aerospace aluminium alloys of the 2000 (copper) and 7000 (zinc, magnesium) series the recycling of process scrap from both metal suppliers and aircraft manufacturers is a well-established, worldwide industry. The recent introduction of a new family of alloys that incorporates lithium has posed a new challenge to the recycling industry owing to the high cost of lithium, its high reactivity to the atmosphere and to refractories and its absence from the specifications of all other registered alloys. Various process options for recycling have been identified, but vacuum distillation has been selected as the most cost-effective and technically feasible solution. Experimental work established that the separation of Li from AI-Li scrap is feasible and an industrial process has been designed. The economics of Li recovery are very sensitive to the AI-Li content of the feed material. Owing to the design of aerospace vehicle manufacturing plants it is expected that the swarf will be mixed with other alloys. A method of enriching this feed has been developed that is based on the control of swarf morphology by thermal and mechanical treatments as a precursor to eddy-current separation. After eddy-current separation and vacuum distillation small proportions of Li are retained in the AI residue. The effects of this on the properties of conventional AI-Si shape-casting alloys were investigated and safe threshold levels have been established.

Jan 4, 1993

By Y. L. Ding, N. A. Warner

Cylindrical pellets made from graphite and chromite mixtures were reduced in high-carbon ferrochromium melts at 1 600-1 695 degrees C, under an atmosphere of almost pure CO. The reduction rate, as measured by gas evolution, increased with increasing melt temperature and graphite addition and with decreasing pellet diameter or height, although reductant particle size had a very limited effect on kinetics. At a pellet size, heat and mass transfer were significant in controlling the early stages of reduction of large pellets while at chromite grain size, gas diffusion was probably a rate-controlling step. The time required for dissolution of unfluxed pellets into the melts was significantly longer than that for reduction. This indicates that pellet dissolution may be the limiting factor in determining the operating parameters for a proposed new process to produce high-carbon ferrochromium using melt circulation

Jun 19, 1905

By B. W. Hester

Report of discussion at January, 1971, general meeting (Chairman: M. J. Cahalan, President) of the paper published in Transactions/Section B (Applied Earth Science), vol. 79, May, 1970, pp. B60-B67, and contributed remarks. Comments were made by Taylor J.T.M., James C.H., Lethbridge R.F. and Heath K.C.G.

Dec 1, 1971

By T. Guyaguler

An analytical technique using computer-based multiple-regression methods was employed to determine the relation between the dust-producing index and inherent rock properties of typical samples from a coal-producing area, one of the aims being to provide a preliminary predictive tool for practical use. The investigation demonstrated that factors varied in their influence under different conditions, the brittleness:toughness ratio and the hardness being the most significant inherent properties with hardness showing the highest positive correlation coefficient

Jun 13, 1905

By J. Drzymala, K. L. Wolters, T. Chmielewski, T. D. Wheelock, D. H. Birlingmair

Microflotation tests were conducted with a modified Hallimond tube equipped with a fritted glass disk and magnetic stirrer to determine whether the results would support an equation that predicts a linear relationship between particle size and the reciprocal of particle density in water for a specified flotation recovery in a given time. Data obtained with the tube for either hydrophilic or hydrophobic solids fit the equation satisfactorily. It was also shown that the natural flotability of molybdenite is somewhat less than that of elemental sulphur and that sodium dithionite is a good depressant for sulphurised pyrite. In addition, it was found that the untreated pyrite and galena used in the study were hydrophilic and did not float by particle-bubble attachment.

Jan 4, 1992

By J. V. Wood, P. Davies, J. L. F. Kellie

A new range of wear-resistant materials is being produced by technology that has been used to develop high performance metal-matrix composites. These include steels and aluminium alloys that can be made as sheet, plate, rod or bar. The incorporation of hard, wear-resistant particles in an alloy matrix is achieved by reactive casting, spray deposition and powder metallurgical techniques. For example, large particles of TiC can be homogeneously distributed in steel during casting and the subsequent product can easily be rolled to plate. Similarly, up to 20% alumina particles and SiC can be injected, respectively, into steel and wear-resistant aluminium alloys by spray deposition. The current state of development of the process is reviewed and indications are given of the projected applications of such materials.

Jan 12, 1992

By R. B. Scott, J. Hewitson

The paper investigates the historical information relating to spontaneous heatings which have occurred within the area from 1955 to date. From this information the seams most liable are identified and the location within the workings is enumerated, together with the possible reason for the occurrence of the heatings. Details are given of the precautions taken during development, working and withdrawal. Sampling procedures are outlined and the interpretation of the results is discussed. Reference is made to the various types of material and techniques employed in both preventing and combating heatings and examples are given of their relative cost and the operational experience obtained. Special observations are made on the changes in mining techniques and their influence on spontaneous combustion.

May 23, 1905

By I. R. Hanby

A simple but comprehensive method has been developed for the simulation of a mechanical-drive dump truck that enables various parameters to be predicted as a function of time throughout its whole cycle. Uses of the simulation results are indicated with specific attention to environmental and operational or economic planning. The output of a sample run is presented. The method can be easily adapted for the investigation of a wide variety of mobile plants.

Jan 4, 1992