Search Documents

By S. M. Saghaeian

The studies on the product finer than 12 mm due to crushing and sizing plant of Gol-e-Gohar Iron Ore mine showed which this material contains significant amount of valuable iron minerals. Based on the carried out experimental studies on representative samples of fine hematite iron ore, a processing flow sheet was designed to upgrade iron content. This plant is known as first hematite iron ore enrichment plant in Iran which the dry medium intensity magnetic separators (with magnetic field intensity 4500 gauss and high gradient) has been used. The main objective of the plant is production of high iron product with iron content more than 61% and weight recovery more than 55% from the feed with iron content of 54%. In this plant, at first material are screened by a single deck screen (6mm), then oversize particles is separated at one stage by magnetic separator, while undersize ones at two stages. Based on the results of experimental tests, a final high iron product with iron content of 62.4% and weight recovery 63.9% can be achieved. It should mention which the iron content can be enhanced through increasing the speed of magnetic separators especially at the part of separation of finer iron ore.

Jan 1, 2014

By Al Cropp, Julie Hunt, Will Goodall, Ron Berry, Dee Bradshaw

Geometallurgy aids the understanding of ore body variability but has the most value if the data is easily available along the entire mining value chain. This requires cross-discipline communication and collaboration across traditional silos, and an organizational culture that encourages that to flourish. Data that are collected by the numerous groups (i.e. mining, geology, milling, processing, refining, smelting, marketing, environmental etc.) involved in the mining process may have relevance to other stakeholders; mineralogical and textural data for example has value to all these groups. Data required for modeling comminution or identifying acid potential from waste rock may already exist, however it needs to be made available to all the relevant stakeholders in the right format at the right time. As part of the GeM (AMIRA P843 & P843A) project the opportunity has been taken during the sponsor meetings, short courses, case studies etc. to ask the question: ‚What information do you want from further up the chain?? For example, to metallurgists ‚What information would you like from the geology group before the ore enters the mill?? The geology group may already have information important to mineral processing but not know it is of interest. This could, for example, be in the form of a geometallurgical drill core log that contains quantitative measured values. This paper focuses on the interaction between the mining, geology, mineral processing and environmental groups, using ore properties resulting from geological alteration to identify potential impacts throughout the mining process and discusses how a cross discipline approach can benefit all.

Jan 1, 2014

By M. Evertsson, K. Bhadani, E. Hulthén, M. Bengtsson

"Modelling and simulations for mineral processing plants have been successful in replicating and predicting predefined scenarios of an operating plant. However, there is a need to explore and increase the potential of such simulations to make them attractive for users. One of the tools to increase the attractiveness of the simulations is through applying optimization schemes. Optimization schemes, applied on mineral processing simulations, can identify non-intuitive solutions for a given problem. The problem definition itself is subjective in nature and is dependent on the purpose of the operating plant. The scope of this paper is to demonstrate two optimization schemes: Multi-Objective Optimization (MOO) using a Genetic Algorithm (GA) and Multi-Disciplinary Optimization (MDO) using an Individual Discipline Feasible (IDF) approach. A two stage coarse comminution plant is used as a case plant to demonstrate the applicability of the two optimization schemes. The two schemes are compared based on the problem formulations, types of result and computation time. Results show that the two optimization schemes are suitable in generating solutions to a defined problem and both schemes can be used together to produce complementary results. INTRODUCTION The comminution process for a mineral processing plant consists of multiple crushing and classification stages and aims to produce fine material to liberate ore from the minerals. The modelling and simulation of such processes are well established using static process models (King, 2001; Napier-Munn et al., 1996). A recent development in the dynamic modelling for such processes has shown further increase in fidelity compared to the static process models (Asbjörnsson, 2015). The developed simulations can be utilized to design, operate and control mineral processing plants based on the requirements of users (Bhadani et al., 2017). Typically, the requirements in the operation of the comminution process are conflicting in nature, as for instance, reduction of power draw by process units, maximization of production of fine materials, and increasing utilization of the process units. These conflicting requirements leads to a Multi-Objective Optimization (MOO) problem to operate a mineral processing plant. The MOO problems are normally referred to as non-linear problems and its fundamental understanding with respect to process behaviour is difficult to achieve."

Jan 1, 2018

By Caroline Olsen

The objective of this study was to achieve Zn activation control in an industrial Cu flotation circuit treating a complex Cu-Pb-Zn-Au-Ag sulphide ore at the LaRonde Division of Agnico-Eagle Mines Limited (Québec, Canada). In order to provide process relevant results, a laboratory testing methodology was developed to duplicate plant operational parameters. The action mechanisms of ZnSO4, TETA (triethylenetetramine) and NaHSO3used as depressants in order to limit ZnS activation were examined. Laboratory flotation tests with and without Cu2+ions (the ions responsible for ZnSactivation)were performed. All depressants showed equal or better flotation performance relative to baseline tests. For example, in the presence of Cu2+, the Zn recovery reduced from 32.2% to 17.5% in the copper rougher concentrate after adding ZnSO4(with a dosage of 50 g/t). TOF-SIMS analyses confirmed the relative decrease in surface Cu in the samples treated with ZnSO4and TETA. For the case with TETA, this indirectlyindicates the formation of a copper TETA complex in solution, thereby reducing available Cu for transfer. The TOF-SIMS and XPS data indicate that the addition of ZnSO4and NaHSO3resulted in an increase in surface metal hydroxides and SO3 on ZnS grains inhibiting both Cu and collector attachment.ZnSO4 was subsequently tested with success in the LaRonde concentrator. The addition of 40 g/t ZnSO4 at the conditioning (or cleaning) stage led to a 2% reduction in Zn content in the Cu and PM concentrate. Recently, improvements towards the control of copper sulfate addition in the downstream Zn flotation circuit resulted in the reduction of Cu2+ in process water. As this ?cleaner? water is recycled for Cu and PM flotation, the addition of ZnSO4 is now used only as required.

Sep 1, 2012

By K. D. Mehta

Copper concentrate containing complex sulphides of Cu-Ni with 14.13% Cu and 10.04% Ni besides impurities such as 0.33% Co and 0.71% Mo, is not acceptable to the copper smelters due to the smelting problems. Selective bioleaching of nickel from the concentrate can be considered an an option to make it suitable for copper smelter. Effect of elemental sulphur and pyrite on the bioleaching of Ni and Co has been investigated using a mixed culture of Acidithiobacillus ferrooxidans (A.f.) and Acidithiobacillus thiooxidans (A.t.). Parameters such as pH, temperature, particles, size etc. were optimised to understand the role of additives in the bioleaching. With 2% S at 308K, 2.0 pH, 5% pulp density and 200µm size particles while shaking at 100 rpm, 79% Ni, 41% Co and 5% Cu were bioleached as compared to the leaching of 81% Ni and 45% Co in presence of 10 wt% pyrite in 60 days; 27% Ni, 24% Co and 4% Cu were recovered in sterile experiment. The selective dissolution of nickel and cobalt as compared to copper may be explained by galvanic interaction between chalcopyrite: pentlandite / pyrrhotite. Bioleaching was facilitated by strong oxidizing conditions due to higher Fe3+/Fe2+ ratio/redox potential (ESCE) as a result of improved interaction of minerals through biooxidation of sulphur and accelerated galvanic interaction by pyrite. The mechanism of selective leaching of Ni and Co was established by XRD phase identification.

Sep 1, 2012

By I. Blayda

The purpose of this work is to study and make comparative analysis of germanium extraction and related valuable components of the sublimates from the burning of domestic power coals (product 1) and germanium sulfide materials, which are a waste of lead-zinc production (product 2), by traditional chemical methods (distillation of germanium in the form of tetrachloride from raw and preliminary burning source) and by microbial bioleaching of sulfur-oxidizing bacteria. The dependence of the germanium extraction by chemical methods from phase composition of the initial raw materials was installed. The germanium tetrachloride extraction from products 1 and 2 were 78.50 and 19.52%, respectively. Such difference in indexes on extraction, is caused by germanium confinement as concomitant trace component to the basic phases to carriers. The share of acid-non-soluble compounds (tetragonal modification GeO2 and silikogermanaties) in the product 1 account for 21.5 % of germanium. Ratio between acid-soluble and acid-not -soluble germanium forms are 19.52 and 80.48 %, respectively, in the product 2. Our experiments have shown, that implementation of restorative firing (with addition of 30-40 % carbon at 1150 0?) of sulfide product 2 considerably impacted on the extraction of germanium tetrachloride (91.76 %) in comparison with its low enough extraction at straight distillation of hydrochloric acid (19.52 %). The results are confirmed by a set of physical methods. The results of processing the same so-called hard phase?s material (product 2) with the help of microorganisms are presented. It Has been established, that selected strains of bacteria are capable of extracting from initial raw materials not only macro components (iron, zinc, lead, manganese, aluminum, nickel), but also micro impurity of rare metals (gallium, germanium, zirconium). It is important that these metals were not extracted by traditional chemical methods (with application of aggressive conditions and heats) independently of the phase composition of the source. Almost complete extractions of germanium in solution using sulfur-oxidizing bacteria take place in the first day of the process independently of the phase composition of the source and the type strain. The results have practical significance and can be the basis for developing a unified biotechnological method of technogenic waste processing with a purpose of their sterilization and detoxification with simultaneous obtaining concentrates of valuable metals. Keywords: germanium, extraction, sublimates, bioleaching, sulfur-oxidizing bacteria.

Sep 1, 2012

By G. W. Zhang

Ultra-fine Stirred Mill is a kind of high energy efficient equipment for ultra-fine grinding, and has been the mainstream equipment in the submicron powder and slurry industry. This paper mainly describes flow-field numerical simulation of the three popular ultra-fine grinding mills: (respective-ly as) Disc Stirred Mill, Pin Stirred Mill and Spiral Stirred Mill, by means of the software Computational Fluid Dynamics (CFD). In the flow-field numerical simulation, the velocity gradient, shear rate dispersion of the flow-field, the viscosity dissipation rate were analyzed with CFD. It is discovered that Pin Stirred Mill has the highest velocity gradient in circular directions and the most homogeneous distribution of shear rate among the three. Flow-field numerical simulation provides a new way (and means to) for the parameter optimization design and project enlargement of Ultra-fine Stirred Mill. The experiments were also carried out, the results are consistent with the results of the simulation analysis. For example, in GCC grinding experiments under the same conditions, the specific energy consumption of Pin Stirred Mill with 3600L in volume is 15%~17% less, and its processing capability is 13%~15% better than Disc Stirred Mill. Now with its optimized structure and excellent performances, more than ten sets Pin Stirred Mill with 3600L in volume have been used in industrial production in Shandong, Guangdong and Hunan province.

Jan 1, 2014

By Steven Wright, Sharif Jahanshahi, Shouyi Sun

"While there is a large industry based on recovering platinum group metals (PGM) from complex sulphide ores containing Cu and Ni, there is little information on the thermodynamics of the matte phase formed on smelting the ore and in particular the behaviour of Pt in the matte.The equilibrium between metallic platinum and industrial mattes was studied in a series of experiments where a small quantity of matte (5g) and platinum foil of 150 µm thickness (0.5 g) were equilibrated in magnesia crucibles at 1400°C under conditions where the oxygen and sulphur partial pressures were fixed.The chemical composition of the phases was determined from EDS analysis using a scanning electron microscope. Line scans were initially used to confirm that the foils had attained a uniform composition across their thickness. The composition of the matte was determined from analysis of an area of matte including the small metallic droplets and dendrites.The results of the equilibrium study are presented in terms of how the oxygen and the sulphur pressure affect the distribution of Pt, between the matte and the alloy foil (Lmatte/alloy). Other variables investigated were matte chemistry, i.e., the Fe content and the temperature. The activities of platinum in the mattes were calculated using a regular solution model describing the activity-composition relationship in the alloy."

Jan 1, 2003

By Diogo R. Prado, José Aurélio M. da Luz

Drying operation can have a major importance in a mineral processing undertaking. The proper sizing of dryers can ensure the specified dewatering level without energy wastage. However, often the sizing of fluidized bed is done disregarding the actual residence time distribution (RTD) of the particles inside the reactor. In this case it is usual to adopt the average residence time as a design criterion. In this work, we have quantified the effect of residence time distribution on drying, ensuring that a previously adopted fraction of the particles remains inside the reactor for the required time lapse needed for drying. Design criteria such as particulate flow rate and drying time, taking into account the statistical distribution of residence time was studied, matching the thermodynamic and fluid dynamic aspects of the drying process. Experimental tests carried out have confirmed the RTD for a teetering bed as the same for a canonical ideal mixing system. Although the fluidized bed volume using the proposed formulation was higher than that found for the average time based procedure, the efficiency gain in drying has proven advantageous.

Jan 1, 2014

By Ahmad Amini, Hadi Abdollahi, Pouya Karimi

Due to detrimental effects of cyanidation process on the environment in gold industry, application of cyanide alternatives such as thiourea are being highly considered in recent projects. In this study, the extraction of gold from poly metal ore, using thiourea was precisely investigated. The representative sample contained 2.5 ppm Au and 160 ppm Ag. The sample was categorized as oxide gold ore, because the main part of its pyrite was changed to iron oxide and hydroxide such as goethite and lepidocrosite. According to mineralogy, the main gangue mineral was quartz. It shows that gold grains are free and interlocked with quartz matrix. Also, the presence of a high amount of silver in free and sulfide forms and also the low content of other sulfide minerals such as base metal sulfides is a remarkable point of these studies. In the gold extraction process with thiourea, there are several parameters that affect the rate of gold dissolution such as concentrations of thiourea as a gold lixiviant and ferric sulfate as an oxidant, pH and size fraction of feed and leaching time. The influence of these parameters on the gold dissolution rate were investigated and optimized. The results showed that the concentration of thiourea is the most influential parameter which could increase the gold recovery to 71% (at 10 g/kg sample). The optimal amount of ferric sulfate was determined as 6 g/kg sample. Also, the optimal levels of size fraction of feed and pH of solution were 88% under 75 micron and 2 as acidity; respectively. Leaching time was 6 hrs. In addition, this sample was leached with cyanide and the optimized values of size fraction of d88=75 microns, pH=10.45, 2500 ppm of sodium cyanide with time leaching of 24 hours were concluded for maximum recovery of gold in solution. Finally, the results of cyanidation tests were compared to the thiourea dissolution after optimizing all affected parameters in cyanidation process.

Jan 1, 2018

By Aubrey Mainza, Malcolm S. Powell

"A hydrocyclone with two vortex finders, named the three-product cyclone (3PC), has been successfully tested in the Platinum industry for dealing with the dense Chromite found in UG2 ores. This dense component preferentially reports to the cyclone underflow, resulting in an over-ground fine Chromite component in the final product. The dense media effect caused by a high concentration of this in the cyclone feed produces a coarsening of the cyclone overflow, which results in loss of recovery through over-size silica in the PGM carrying component material in the float feed. The fine barren particles of Chromite that report to the overflow are recovered through entrainment in the flotation process, resulting in detrimental contamination of the slag produced from the concentrate.Data from many industrial scale tests of the 3PC have shown that three distinct products are obtained when the inner vortex finder length (LIVF) is extended to the region either above (normal classification) or below (reverse classification) the transition zone (a region were the inner and outer overflow streams are identical). Due to wear problems arising from extending the IVF deep into the cone of the cyclone, it is advantageous to use the shorter IVF. Only the normal classification results are reported here, but similar outcomes (to opposite overflow streams) were obtained for the reverse classification. The results showed notable differences in the percentage split of the plus 100µm material in the product streams, confirming that three distinct products are discharged from the 3PC. About 12% of the plus 100µm material in the feed reports to the middlings stream, 1% reports to the final product, and the remainder to the cyclone underflow.Results of silica and chrome splits to the three distinct products namely, the inner overflow (INO), the outer overflow (OUO) and the underflow (U/F) are given in Table 1. These show that the 3PC can be used to recover coarse silica through screening the middlings product - which has a high silica content. When the vortex finder ratios (ratio’s of cross-sectional areas) are carefully selected, the split of plus 100µm silica to the middlings product ranged from 2.9 to 9.6%. Large amounts of oversize silica and chrome report to cyclone underflow, explaining their high percentages in the underflow stream."

Jan 1, 2003

By Q. R. Chen

Wet processes are commonly used in coal preparation field home and abroad. Dry coal cleaning technology is very necessary in China because more than 2/3 of coal resources deposited in arid areas, which are difficult to separate coal with wet processes. A particular interest of this article is the discussion of separation research development of dry coal cleaning in China, such as an air dense medium fluidized bed (ADMFB) beneficiation technology, a compound dry (pneumatic) separation technology and a triboelectrostatic separation technology. The fundament and importance of dry coal cleaning methods above were introduced. On the basis of analyzing parameters which influence the performance of separators, including that of structure, technologic and operating, the separation research status of dry coal cleaning methods, especially the ADMFB beneficiation technology, were discussed and reviewed. The recent developments, especially the fluidized bed beneficiation for <6mm fine coal with an external energy assisted, including a vibrated fluidized bed and a magnetically fluidized bed, and the triboelectrostatic separation for <1mm fine coal are also introduced. The study and application results in China show that dry coal cleaning technologies can efficiently beneficiate different coals with different sizes. The ADMFB can separate >6mm coarse coal with an E value of 0.05~0.08, the external energy assisted fluidized bed can separate <6mm fine coal with an E value of 0.07~0.09, the triboelectrostatic technology can efficiently separate <1mm fine coal, and the compound dry separation technology can efficiently separate >3mm coal with a easy washability. The dry coal cleaning provides an efficient and lower cost clean approach for coals distributed in arid areas.

Jan 1, 2014

By Tilak Raj Mankhand, Mudila Dhanunjaya Rao, Kamalesh K. Singh

"Zinc dust is used for the removal of primary impurities by cementation from the zinc sulphate electrolyte before electrowinning of zinc. However, the industrial zinc electrowinning plants has been reported that the zinc dust consumption is in large excess than the stoichiometric requirement. In the present investigation, morphology of the zinc dust has been altered by ball milling and utilized for the cementation of cadmium, which is one of the major impurity and compared the change in the rate of cementation with original zinc dust. Initially, 325 mesh size zinc dust was used for the optimization of the excess quantity of zinc dust to be used at a temperature of 50 °C. The chemical analysis of zinc dust before and after ball milling and morphology were studied by scanning electron microscopy (SEM), and the solution was characterized by Atomic Absorption Spectrophotometer. The rate of cementation increased with increase in ball milling time. The residual precipitate obtained after filtration was also characterized by X-ray diffraction analysis. Finally experiments were conducted to study the effect of temperature and kinetics of cadmium cementation using first order reaction kinetics. Based on the integral method, the calculated activation energy for the cadmium cementation with 4-hours ball milled zinc dust was found to be 3.39 KJ/mole. INTRODUCTION Primary production of zinc in the world is carried out by hydrometallurgical route. The primary impurities in the neutralized zinc sulphate solution that cause negative effect on electrowinning are copper, cadmium, cobalt, and nickel. Copper diminishes the current efficiency and cadmium contaminates the cathode zinc (Morgan, 1977) while electro winning. Nickel and cobalt lead to perforation in the zinc deposit and prevents the electro winning process (Abrasheva et al, 1984). Due to higher electro positivity of these metal impurities than zinc, they can co-deposit with cathode zinc at the time of electrolysis. In addition to that, some possible impurities (including cobalt) in the electrolysis may lower the hydrogen overvoltage, allowing deposition of hydrogen at cathode resulting in fall of current efficiency. The deposition of zinc on the cathode is possible only at higher hydrogen overvoltage which is practicable in the absence of such impurities (Raghavan et al., 1999). Cementation is one of the prominent purification technique, and in that less reactive metal can be replaced by highly reactive metal by allowing them into precipitation. Cementation of cadmium from zinc sulphate electrolyte is being done by the addition of zinc dust."

Jan 1, 2018

By Buks Kruger

"After the milling and flotation of the platinum bearing ore, the flotation concentrate is electrically smelted in 6-in-line electric arc furnaces and the resulting furnace matte treated in Peirce Smith converters to remove the iron sulphide. The iron free (less than 1% Fe) converter matte is then granulated and sent to the Base Metals- and Precious Metals Refineries for further processing.During the smelting and converting processes two distinct gas streams are produced.The Peirce Smith converter off gas contains 4% - 9% SO2 which is treated in a conventional Sulphuric Acid Plant to produce sulphuric acid (H2SO4).The electric furnace off gas contains 0.9% SO2 and was (until September 2002) vented through a 91 meter high stack to atmosphere.Off gasses which contain less than 3% SO2 is difficult to handle and quite a few processes had been developed over the years to cope with this gas. A broad spectrum of process suppliers and technology approaches is available and the different technologies can be divided into a few main approaches i.e.Scrubbing of the off gas with an alkaline solution to produce an environmentally friendly and stable waste product which can be discharged onto a tailings dam or permanent landfill site.Physical absorption of the SO2 into a chemical solution to produce high quality chemically pure process chemicals.Catalytic reaction of SO2 with O2 to produce SO3 which is absorbed in water to produce sulphuric acid of less than 90% strength.In October 2002 Impala Platinum commissioned a Sulfacid Plant at its Smelter in Rustenburg which recovers the SO2 from the electric furnace off gasses into a weak sulphuric acid solution.The Sulfacid Plant technology is widely used in the paint pigment industry. This is, however, the first application of the technology on electric furnace off gas.The furnace off gasses contains flue dust which is removed in electrostatic precipitators. The gas exiting the precipitators normally still contains between 40 mg/Nm3 and 60 mg/Nm3 dust and passes through a quench-scrubber before entering the reactors. The quench-scrubber cools the electric furnace offgas down from ± 200 °C to 60 °C and act as a final dust removal stage."

Jan 1, 2003

By M. Lak, M. Asghari, M. Saghaeian, R. Hejazi, A. Haratian

"Magnetic separation techniques are used extensively in mineral processing operations. Magnetic separators are robust and relatively easy to operate. As the ore get hard and low grade, fine grinding must be required mostly to allow for a high degree of mineral liberation. These processes encounter the magnetic separation process difficulty due to a significant change in the separation behavior of particles. This study investigates the effectiveness of a novel proven wet magnetic separator for the beneficiation of Lebedinsky (Russia) iron ore achieved through developing pole arrangement and tank design. Basis on the results of multiphasic simulation of a medium intensity magnetic separator (MIMS) and dense media tank using Magnetic Design Software, a new model of the MIMS separator was developed. The main of the new MIMS separator was focused on improving separation and the decreasing the number of separators in cobber stage of the plant. The new MIMS separator was tested into a pilot plant on the received samples from Lebedinsky iron ore plant. In addition to the basis on the results of the modeling, promising results of test work and previous experiences, it was claimed the unit capacity of new separator is 33.33% more than the existing separator that could decrease the number of separators. In addition, the significant energy saving in the same operational condition could be obtained without any important adverse effect on the final concentrate quality.INTRODUCTION Magnetic separation is a long-established method for the purification and removal of substances from fluids (Augusto et al., 1999; Buck et al., 2015; Hoffmann et al., 2002; Lauda et al., 2016; Lindner et al., 2010; Podoynitsyn et al., 2016; Rashidi et al., 2016), mainly in mining processing industries ranging from steel production to coal desulfurization as commercial technology (Andres, 1994; Augusto, 2002; Svoboda, 1987). High gradient magnetic separation as an effective method for recovering of weak and fine magnetic particles separation has undergone dramatic developments, and has also achieved extensive application during this time (Svoboda and Jujita, 1987). Magnetic separation operations can be categorized into high intensity as electrical (up to 20,000 gauss), Medium intensity (2000-5000 gauss) and low intensity (less than 2000 gauss) techniques. Magnetic separators offer a simple, clean and economic way to sort magnetizable ores and minerals. After pulverization, the material is run through an inhomogeneous magnetic field, where particles of different susceptibility experience different magnetic forces. The force increases with susceptibility, magnetic field and field gradient (Jongst et al., 1984).In magnetic separation, the difference in the susceptibilities of the various particulate materials is used to separate the material flow into two or more products (Wasmuth and Unkelbach, 1991). The magnetic force acting on a particle can be calculated using the following equation:"

Jan 1, 2018

By J. Gong

Fine mineral particles pose two challenging problems in froth flotation, i.e., ineffective recovery of fine hydrophobic particles and mechanical entrainment of fine hydrophilic particles. The first problem has attracted much research effort while the second problem has received much less attention. We have recently proposed a method to deal with mechanical entrainment, i.e., utilizing the flocculating power of polymeric depressants to flocculate fine gangue particles and making the flocs big enough so that the mechanical entrainment of these particles can be reduced or eliminated. In this paper, we report results on the use of polyethylene oxide (PEO) in controlling quartz gangue in the flotation of sulphide ores. PEO was found to flocculate fine quartz and lower its entrainment. It was also found to modify air/water interfacial properties and acted as a frother, which could increase gangue entrainment. Nevertheless, when used at starvation dosages, PEO was found to significantly improve the grades of the floated sulphide concentrates.

Jan 1, 2014

By Chen Jianhua, Shen Zhenchang, Zhang Ming, Chen Feifei

"With flotation cells scale-up, the performance of flotation cells is increasingly variated for short-coming and dead zones existing. The residence time distribution which shows the movement of tracers can assess the unexpected flows such as short circuit and dead zone in a flotation cell. In this paper, the residence time distribution of pilot flotation cell is investigated with CFD simulation. Based on the theoretical model, the short-coming probability and dead zone probability are quantitative. The ideal average residence time is similar with the actual average residence time. The mixing effect of the flotation cell approaches the ideal continuous stirred tank reactor. The operating parameters such as speed and feed velocity have complicated influence on residence time distribution. The research would be helpful to understanding flow in flotation cell and improving performances of flotation cell.INTRODUCTION Froth flotation is a method which purifies minerals according to difference of physical and chemical surface characters of different mineral particles (Shen, Z., Chen J, 2012). Flotation cell is a key equipment for froth flotation method. The flotation cell performances have great influences on flotation index.It is difficult to evaluate flotation cell how to improve flotation procedure to complexity. The main flotation cell performances are aeration volume, air dispersion, solid suspension and residence time distribution, etc (Shen, Z., Lu, S., 2008). Residence time distribution is an important fluid hydrodynamics which could reveal the flow of pulp, mixing of particles and air bubbles. In the flotation cell, the ideal average residence time of pulp could obtain easily. But the fluid differential units would be different flow paths. The residence time of the fluid differential units is variation and would be longer or less than the average residence time. The residence time distribution would reveal the mixing effect and predict the not ideal flow in the flotation cell such as shorting cutting, dead zone, etc. As we know, the shorting cutting and dead zone would be decreased the real flotation time and it is disadvantage to better flotation effect, especially for large flotation cell. It is impossible to eliminate the not ideal flow totally. It is very important to reveal and decrease the shorting cutting and dead zone probability in the flotation cell."

Jan 1, 2018

By Y. S. Sun, P. Gao, Y. F. Li, J. W. Yu

"Oolitic hematite ore is one of the most refractory iron ores in the world. It is not feasible to separate iron minerals from raw ore by conventional mineral processing methods. In recent years, a new technology called coal-based reduction followed by magnetic separation has been employed to produce metallic iron powder from oolitic hematite ore effectively. In order to find the nucleation mechanism, a thermodynamic analysis of the carbothermic reduction of oolitic hematite ore was conducted by the HSC 6.0 thermochemical software. The phase transition and microstructure changes during the coal-based reduction were also investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). The results showed that the iron oxides in the oolitic ore were reduced to metallic iron following the route of Fe2O3–Fe3O4–FeO–Fe in reduction process. The reduction reactions preferentially occur in the high activity regions to form a higher concentration of Fe elements, and then more supersaturated Fe separated out to form new phase nuclei. Under the action of homo-aggregation and principle of minimum free energy, the iron cores continuously absorbed migratory Fe around and grew into quasi-spherical iron particles embedded in slag phase. INTRODUCTION With the rapid increase of steel industry, premium grade iron ore in China has been gradually exhausted, and its supply has become bottleneck for the development of iron and steel industry (Guo et al., 2015). Therefore, it is urgent to exploit the refractory iron ores, such as oolitic hematite ore. Oolitic hematite ore is widely distributes in France, Germany, America, Canada, Pakistan, China, and among other countries (Maynard and Van Houten, 2004; Li et al., 2011). In China, the explored reserve of oolitic hematite ore is 3.72 billion tons, which accounts for approximately 1/9 of total iron ore resources of China (Gao et al, 2016). Oolitic hematite ore possesses complex composition,"

Jan 1, 2018

By D. Hatfield, G. de Jager

"The rapid developments in computer vision and computational resources are creating new possibilities for the use of machine vision systems for industrial control. A number of commercial image analysis systems exist, and research into improved measurements of froth performance is ongoing. An integral part of the implementation of these systems is the validation of the relationship between image analysis measurements and flotation cell performance. This paper discusses the factors affecting concentrate flow and presents the results obtained from one such system with respect to its ability to estimate the flow of concentrate from a flotation cell.The relationship between froth flow speed and the rate of recovery of concentrate from a flotation cell was investigated on two industrial operations, both processing PGM (Platinum Group Metal) bearing ores. Results are presented that show a relationship between froth flow speed and concentrate yield."

Jan 1, 2003

By Erico Tabosa

The turbulence characteristics and measurement techniques for agitated tanks are well established for liquid and liquid-gas systems. However, the literature shows that the overall energy dissipation rate (related to turbulence) is affected not only by air addition, but also by the concentration of solids. Unfortunately, there are no reliable measurement techniques for characterizing turbulence in a three phase (liquid-solids-gas) environmental system, which is the case in a flotation cell. Therefore, the effect of turbulence on flotation kinetics is very much one of conjecture. The aim of this work was to develop a sensor to characterize the degree of velocity fluctuation, which is related to turbulence, in a flotation cell operating with slurry and air. This sensor comprises a piezoelectric film transducer that converts mechanical to electrical energy. Hence, when the sensor deflects backwards and forwards an AC voltage is created. Flotation studies carried out using this sensor in a 3m3 Metso RCS cell processing a copper sulphide ore showed a highly turbulent impeller zone with transition to a significantly less turbulent zone in the upper portion of the cell. The transition region moves as the cell operating variables are changed, for instance the impeller speed, impeller size, air rate and feed solids concentration. Keywords: mechanical flotation cell hydrodynamics, turbulence characterization

Sep 1, 2012