Search Documents

By S. J. Lui

Sodium oleate was an effective diaspore collector, whereas chelate collector OL2 showed certain collecting power over diaspore and nonionic surfactant OL3 showed little collecting ability. Then experiments were carried out using sodium oleate as the main collector with the addition of OL2,OL3 to study the influences on diaspore flotation, it could be seen from the experiments that accelerants had a marked influence on the recovery of diaspore, which could be raised by 10%, and the addition sequence also affected the flotation behavior: the best results could be gained when the accelerants were mixed thoroughly before adding and the best ratio of collector OL1 and accelerant OL2, OL3 stood at 30:2:1. Based on the calculation of the ingredients in the sodium oleate solution, sodium oleate reacted with surface of the mineral and formed the acid-soap polymer [HOl?Ol-] when pH was about 9. Zeta potential test showed the accelerant promoted the absorption of collector on the mineral surface, which lowered zeta potential. As could be seen from surface tension experi-ments, the addition of accelerant OL3 lowered the CMC value of OL1 solution, which was equiva-lent to raise the power of the agents. Further Infrared Ray experiments showed the co-absorption of OL1 and OL2 make aluminum oleate on the mineral surface more stable. Up till now, the mixed reagents with sodium oleate as the main collector, combined with other two accelerants had been used in the Zhongzhou concentration plant, which is the first diaspore flotation plant in China.

Jan 1, 2014

By ?. S. Potokin

"In general the electric pulse treatment is composed from two processes – electric pulse grinding and electric explosive (electric discharging) activation. The electric pulse grinding with the effect of selective destruction refers to a major slag fraction, more that 2-5 mm, when a one can see a physical prerequisites for electrical breakdown of the slag particles. The electric pulse treatment of slag is considered as an additional operation in the technological scheme extraction of non-ferrous metals from copper smelting slags in addition with mechanical grinding, flotation enrichment and acid leaching. Studies of the reprocessability of pelletized slag have shown the possibility of higher extracting non-ferrous metals via flotation after electric pulse disintegration (EPD) treatment. By using EPD of slag pellets, it is possible to increase the non-ferrous metal yield to concentrate by 18-24%.INTRODUCTION The use of the explosive effect of the plasma discharge channel at electrical breakdown of a solid at a pulsed high voltage is the physical basis of the electric pulse method of destruction of geomaterials (Vorobiev et al., 1971; Andres, 1995; Semkin et al., 1995). The flowing of a pulsed current in the discharge channel is accompanied by a sharp increasing of plasma’s temperature and pressure, leading to a supersonic expanding of the discharge channel, the formation in the solid of intensive mechanical tension field, spreading of cracks, and eventually, to the destruction of the solid. Fragmentation and grinding of ore and mineral aggregates by electric pulse method due to a number of specific physical mechanisms of power load and crack formation, belonging only to this method, is different by high selectivity of destruction. This ensures better liberation of grains of individual minerals and their better preservation from destruction and less formation of a slurry output. These features creates the prerequisites for a more complete extraction of a useful mineral in the concentrate during ore dressing, to improve the quality of concentrate. In contradistinction to mechanical methods, electric pulse technology does not contaminate the product with instrumental metal, material of lining and grinding bodies. The possibility simply and in a wide range to change the dynamic load character allows to regulate the granulometric composition of the product of grinding, to obtain a narrower class of product size than is possible with mechanical grinding. The product of electric pulse grinding is characterized by less roundness and large specific surface area of grains due to the trait, that a new surface is formed in the process of splitting during the expanding of cracks. The degradation product has increased sorption and reactivity in chemical reactions. Liberation of the mineral inclusions particle better corresponds to their initial natural state in the rock and this is the great importance for the study of mineral raw materials."

Jan 1, 2018

By Lilong Huang, Xiang Zhao, Yuan Long, Li Shi, Guowang Zhang, Xiao Xiao

"Vertical stirred mill is expected to upgrade the iron concentrate by further size reduced efficiently. The tests for fine grinding of iron ores from Baiyun Boyu iron ore, Baogang Goup, iron contained tails of Cu-Pb-Zn ore in Wanguo ore, Xiaoshalong iron ore in Qinghai were conducted in this paper. The data of appropriate grinding fineness, optimum grinding conditions and energy consumptions obtained from the test were used to select appropriate scale of the vertical stirred mill, optimize the parameters of the grinding process and upgrade the iron concentrate of the iron ore dressing plant or design the new ore dressing plant. Based on the laboratory tests, industrial system of regrinding and magnetic separation with vertical stirred mill as the regrinding mill in micro-fine grained iron concentrate upgrading has worked out very well. The grade of Fe in iron concentrates has increased to about 65.0% (by 4.0~6.5 point percent) when the iron concentrates were reground to designed fineness and the specific energy is 5.0~7.1kWh/t. The system of regrinding and magnetic separation is proven to be eco-efficient in iron concentrate upgrading."

Jan 1, 2014

By Z. B. Pan

The innovative point of this new technology can be described that under normal pressure and 70°C, using a new combined activating and oxidizing agent, the minerals bearing arsenic and organic carbon are oxidized effectively. This technology can be applied in commercial scale. The high carbon and arsenic bearing gold ore is taken from Gansu, where hundreds of tons gold deposit. The ore has 0.51% of arsenic and 1.75% of carbon (1.07% of organic carbon). The gold occurs mainly in native with particle size 0.02~0.6 mm and a few are enwrapped by pyrite and arsenopyrite. The traditional cyanide leaching process gains a very low gold leaching rate with only 5%. Through systemic experimental study, the technological flowsheet of flotation process for concentrating gold, then pre-treating the gold concentrate followed by cyanide leaching the gold concentrate are used. With 4.92 g/t gold of head sample, the gold concentrate with 46.52g/t gold grade and 96.53% gold recovery is gained by flotation process. Followed by pre-treatment for 6 hours, the gold concentrate is leached with cyanide after filtration and washing. The total gold leaching rate is up to 95.44%.

Jan 1, 2014

By A. P. Liu

Semi-industrial test on fine products of Meishan dressing plant was carried out with type RP80/25 high pressure roller mill produced by Homburg Corporation of Germany, and the influences of such factors as energy consumption, water containing, throughput and circulating load on rolling effect were investigated. Closed circuit experiment result showed that Meishan iron ore could be suitable for powder grinding with high pressure roller mill, and energy consumption of the operation was declined by 25%~30%, which was favorable for energy-saving, increasing production efficiency and improving grinding effects. According to above experimental results, this paper put forward the technical proposal of application of high pressure roller mill in Meishan, and pointed out some technical problems which needed to be settled urgently in technology disposal.

Jan 1, 2014

By A. Zangooi

Frothers play major roles in flotation through interaction at the air/water interface. A method of determining frother adsorption density (coverage), i.e., the number of molecules per unit of interfacial area of bubble surface, is introduced. The technique is based on mass balancing the frother around a continuously operated bubble column. The mass balance requires collection of bubbles before they burst. The column design and operating procedure is reviewed, and some preliminary results discussed. Keywords: flotation, colorimetric frother analysis technique, frother mass balance, coverage

Sep 1, 2012

By M. J. Lottering

Gold deposits in South Africa are invariably associated with uranium bearing minerals. Although it is low grade uranium by international standards, averaging around 0.3 kg U3O8 per ton of ore, recovery of uranium as a by-product improves the overall economics of gold extraction. Moreover, the current high uranium prices as well as increased demand due to renewed interest in nuclear power provide significant incentives for dedicated uranium production. An understanding of the uranium leaching response to changes in operating conditions is an important first step to-wards optimisation of uranium recoveries. In South African acid leaching plants, uranium dissolutions higher than 90% are difficult to achieve, and the chemical origin of this limit is not clear. To study leaching behaviour, an important consideration is the mineralogical characteristics of the ores. Typically, a diagnostic leaching approach can be followed. In this paper, a mineralogy-leachability explanation is presented to rationalise the difficulty in exceeding 90% dissolution from low grade uranium ores on the basis of a simple diagnostic leaching method. It was found that brannerite was the main reason for the existence of a dissolution limit in Witwatersrand ore and that chemical liberation was more effective to increase end dissolution compared to physical liberation. The findings from these investigations will form guidelines for developing economically viable flow sheets for improved uranium recovery, at least in a South African (Witwatersrand) context.

Jan 1, 2014

By M. Chettibi

The interaction and galena flotation with xanthenes and dexanthogen regularities have been de-fined. So, using thermodynamic method of analysis, the thermodynamic stability of [galena - xanthenes - water] system and the behavior of lead xanthenes surface state in solution were devised. Thus, results of cared out calculations and experimental investigation completely coincide with-out depending on witch product of sulfur oxidation is formed in the solution. In additional, was obtained quantitative physico-chemical models for the necessary xanthenes concentration of lead sul-fide complete flotation in the tuning fork of: at ?? values from 7.0 up to 9.0 (or at the formation of lead carbonate PbCO3 ) and at ?? values from 9.0 up to 12 (or at the formation of lead hydro carbonate Pb3(OH)2(CO3)2 Physico-chemical models derived can be used as the criteria for functional units of automation systems to control and regulate the flotation process in mineral processing plants.

Jan 1, 2014

By I Brum

Brazil and Colombia have large reserves of coal, those reserves in Brazil are located predominantly in the south and Colombia the main reserves are located in the north. Despite the relative ease of exploitation, these resources have been underestimated as a source of energy. Currently, these countries are developing projects and partnerships aiming to qualify this mineral resource, adding quality to the final product of the processing plants. In this scenario the processing of Brazilian and Colombian coal in flotation columns appears as a promising alternative, having been successful in mineral systems containing fine particles This paper aims to study the overall process of column flotation for a specific Brazilian coal and a specific Colombian coal. The material used in this study consists of fine coal from Brazil (Copelmi) and Colombia (Cerrejon). The objective is to recover carbonaceous matter and reduce the ash and contaminants grade. The two coals were floated using a negative bias in a 5 cm diameter conventional flotation column of 5 m high. Flotation parameter investigated included air velocity in the range 0.6 to 1.5 cm/s. For all runs, a constant negative bias of -0.25 cm/s and a pulp concentration of 8% w/w were used. For Cerrejón coal, 300 g/ton of frother and 907 g/ton of collector was used, whereas for Copelmi coal, 600 g/ton of frother and 1815 g/ton of collector was employed. The frother was a commercial Aerofroth 65 (AF65), whereas the collector was Kerosene. For the Colombian coal, in general, yield, organic recovery, ash recovery and water recovery decreased with the increasing air rate. However, for Brazilian coal the air rate had no significant effect. For Colombian coal, the highest yield (60% w/w) and organic recovery (69% w/w) were obtained at the lowest air rate (0,6 cm/s). Keywords: negative bias, column flotation, coal

Sep 1, 2012

By T. Tumidajski

The purpose of the separation processes in coal processing is obtaining products of certain ash contents. In the most of cases it is assumed that the separation process is described by one, selected parameter, which usually is grain size or material density. The separation may be described by means of statistical distributions of random variables, what allows forecasting the separation results of certain enrichment method. There are very well known the applications of approximations of Tromp separation curves or distribution functions of Erasmus, Meloy or Weibull. It is necessary to say that if the fitness of the approximation more suitable, then the characteristics of the process itself is also better. In purpose of obtaining more appropriate results, these methods were modified by application the mathematical functions, as i.e. hyperbolic tangens function. Furthermore, on the basis of empirical data, so-called interpolations may be performed in purpose of getting more appropriate results of approximation. One of the most known techniques of interpolation is Hughes method. This method for interpolating standard data involves breaking down each interval into a number of smaller sub-intervals. The results of such one-dimensional approach not always contain the full in-formation of the searched distribution. It happens because such interpretation of the problem is not completely correct. In practice, the separation process depends not only on the one parameter (i.e. grain size), but also on many other features characterizing certain material (i.e. its density). It seems then that in some cases the application of multidimensional grain characteristics distributions will be more appropriate. In this paper, the technique of joining the distributions of grain size and density by means of so-called Morgenstern distributions is shown. The general form of these distributions is as following:

Jan 1, 2014

By M. M. Kulkarni1

Kaolin clay is used as a filler and pigment in various applications such as paper, paint, rubber, plastics, adhesives, ink and ceramics etc. Major mineral content in crude kaolin clay is kaolinite along with some accessory minerals as quartz, hematite, mica, feldspar, anatase, rutile, illemnite etc. The Fe and Ti bearing minerals play very important role in determining quality of the kaolin, as these minerals impart yellow, pink or darker color to the white kaolin. Conventional beneficiation methods used in kaolin processing are de-gritting, classification and sodium dithionite bleaching, which improves the optical properties of kaolin, wherein reduction of color imparting constituents such as Fe2O3 and TiO2 is marginal. In the present study, these coloring impurities are separated using selective adsorption of water-soluble polymers. Degritted kaolin samples after passing through 45 micron sieve is used in the study for selective flocculation by polyacrylamide based polymers. The effect of pH, zeta potential, and polymer dose on the reduction of impurities is studied. Analytical tools such as XRF, XRD, SEM, and TEM techniques are utilized and results are discussed in detail.

Sep 1, 2012

By M. Saghaeian, R. Hejazi, L. Hosseini

The specific surface area (Blain value) of iron ore concentrate entering the pelletizing plant is one of the characteristics most effective on the overall performance of the plant such as producing harder pellets, decreasing additives consumption, and decreasing energy consumption. Therefore, preparing the feed entering pelletizing plant is required. The iron concentrate entering Ardakan pelletizing plant located in Yazd province, Iran bears relatively low Blain value (approx. 1600 cm2/g) which necessitates one stage of regrinding so as to increase the Blain value to more than 1800 cm2/g. Studies were conducted and results showed that HPGR is the best regrinding equipment for increasing specific surface area. Conducting pilot plant tests on the concentrate sample revealed that specific throughput is 181 to 263 ts/hm3 and specific energy consumption is 1.6kWh to 2.2 kWh. Pilot tests also showed that one stage of grinding results in 407 cm2/g to 553 cm2/g increase in specific surface area. Based on these results, diameter of rolls, length of rolls, power consumption and grinding force were calculated to be 1.3 m, 0.9 m, 1276 kW and 13800 kN, respectively. Therefore, an HPGR with a roll diameter of 1.52 m, roll width of 1.1 m, power of 1660 kWh and a capacity of 500 t/h has been selected and implemented in Ardakan pelletizing plant. Industrial performance of HPGR and its effects on the plant study results show that limestone and bentonite consumption has reduced about 60% and 30%, respectively. Total Fe of the final pellet has increased from 65.5-65.7% to 66.2%. Cold compressive strength (CCS) and porosity of final pellets are approximately 292 kg/pl and 20.4, which are in the acceptable range.

Jan 1, 2014

By E. G. Ozhogina, O. B. Kotova

"The ores of black, non-ferrous, rare, noble metals are mostly distinguished by a variety of mineral types and complexity of their material composition. This article is devoted to the promotion of the concept of mineral processing in modern realities of the deficit of high–grade ores and increase in their demand. Normative and methodical documentation for specific types analysis with the definition of the field of application are presented in this paper. . For example, the pyrochlore-monazite-goethite ores from one of the deposits from Eastern Siberia - Chuktukonskoe ore field were tested. The development of mineralogical methods and testing of specific raw materials are shown. The method of small-angle X-ray (and also synchrotron) scattering, which was developed for solving problems associated with structural high-resolution diagnostics, was tested for bauxites of Vezhay-Vorykvinskoye field.INTRODUCTION A highly intense production of many types of mineral deposits results in gradual depletion and of mining-geological and mining-technical conditions of various ore reserves ?. Relatively easily accessible and rich deposits are getting depleted in the first place, and it is necessary to involve low grade and refractory ores into production and processing. Traditional technologies can hardly be applied (Chanturia, 2017; Bazin et al., 2014; Ponaryadov, 2017). The urgency of development of the concept of technological mineralogy focuses on the confirmation of new methods and approaches to the development of mineral deposits, creation of scientific and methodological pre-requisites for solving the problem of rational development of mineral deposits, maximum extraction and integrated application of all minerals (both principal and associated), expansion and strengthening of mineral and ores.The article is aimed at updating tasks that should be addressed within the applied mineralogical research: – forecast of quality of ore at early stages of exploration and technological indicators for the redistribution of properties ore, – interactive monitoring of these indicators by mineralogical and analytical methods;"

Jan 1, 2018

By E. G. Ozhogina, O. B. Kotova

"The ores of black, non-ferrous, rare, noble metals are mostly distinguished by a variety of mineral types and complexity of their material composition.The article is devoted to the promotion of the concept of mineral processing in modern realitiesof the deficit of high-quality ores and increase their demand.Normative and methodical documentationsfor specific types of analysis with the definition of the field of application are shown. For example,the pyrochlore-monazite-goethite ores from one of the deposits from Eastern Siberia - Chuktukonskoe ore fieldare tested. The development of mineralogical methods, and testing of specific raw materials are shown.The method of small-angle X-ray (and also synchrotron) scattering, which was developed for solving problems associated with structural high-resolution diagnostics, was tested for bauxites of Vezhay-Vorykvinskoye field. KEYWORDS Technological mineralogy, rebellious ores, ore quality assessment, ?mineralogical-analytical methods INTRODUCTION A highly intense production of many types of mineral raw results in gradual depletion and deterioration of mining-geological and mining-technical conditions of development. Relatively easily accessible and rich deposits are getting exhausted in the first place, and it is necessary to involve poor and rebellious ores into production and processing. Traditional technologies can hardly be applied (Chanturia, 2017; Bazin et al., 2014; Ponaryadov, 2017). The urgency of development of the concept of technological mineralogy focuses on the confirmation of new methods and approaches to the development of mineral raw, creation of scientific and methodological prerequisites for solving the problem of rational development of mineral raw, maximal extraction and integrated application of all minerals (both principal and associated), expansion and strengthening of mineral and raw base. The article is aimed at updating tasks that should be addressed within the applied mineralogical researches: – the forecast of quality of ore at early stages of exploration and technological indicators for the redistribution of raw, – interactive monitoring of these indicators by mineralogical and analytical methods; – assessment of environmental consequences of mining and processing of minerals and measures that eliminate these consequences."

Jan 1, 2018

By H. R. Manouchehri

The importance of the grinding environment and its effect on sulphide minerals flotation behavior has been known for many years. The grinding environment may play a role in controlling fine and coarse particle flotation along with dissociation of different chemical species in grinding environment. Dissociation of different chemical species and ions within the process water may result from changing the grinding environment. The mining and mineral processing industry undertakes activities that may impact on water resources. These include use and storage of chemical storm-water management, process water management, mine dewatering and management of tailings. In mineral flotation understanding and controlling water quality is paramount important not only because of its effect on flotation but also with respect to control the quality of the water which is released to the environment. Releasing of different anionic and/or cationic chemical species in the process water results from the interactions among different mineral within the ore, process water, and the milling environment. In fact grinding mill acts as an electrochemical reactor which affects the flotation performances of different value minerals as well as the quality of the tailing products. An increasing in antimony content in process/discharge water at Boliden?s Tara processing plant in Ireland to above limitation level was reported in April 2010 which needed to be controlled. An increase up to 6 times of the permitted level was reported which needed an immediate action to control due to environmental considerations. Therefore attempts were made to detect why this higher amount of Sb is released and how to control and minimize its release to the process/reclaim water. This paper discusses how/why Sb content in process/reclaim water was increased by changing the mill electrochemistry and the strategies were taken into considerations to control it. Different strategies, including electrochemical controlling of the milling section, Fenton process, using Bauxsol in treating the process water, etc., have been considered and tested which are described herein. All strategies taken into consideration for solving the problem were successful which indicated good understanding of the issue and good decision making. Furthermore, for each solution the capital and operational costs were roughly estimated. Accordingly, the Sb content in process/discharge water was controlled to a value lower than allowed limitation, i.e., 1 ppm. Keywords: antimony, water contamination, mill electrochemistry, ag milling, grinding media, eh-ph, sulfide minerals, fenton process, bauxsol, lime addition

Sep 1, 2012

By G. Sedelnikova

This paper is aimed to elucidate the problem of copper losses in pyrometallurgical slag. Currently, flotation is used to recover copper from the slag and return the metal into the pyrometallurgical process, but the percentage of recovery frequently remains unacceptable. The process of copper leaching from the slag flotation tailings using biologically regenerated ferric sulfate is considered here as an approach to the issue. A sample of the slag flotation tailings containing 0.67% Cu and 4.99% Zn was supplied by the Urals Mining and Metallurgical Company (UGMK, Russia). The Cu and Zn speciation analysis of the sample demonstrated that Cu occurred as 58.1% oxide, 15.4% native Cu, and 18.1% secondary sulfides whereas chalcopyrite proportion was as low as 8.4%. Prevailing Zn species were refractory (58.9% Zn ferrite), and zinc oxide and silicate species made just 37.2% of the total metal content. The silicate generated silica gel that strongly hampered filtration. As demonstrated, Cu recovery is a possibility, which is apparently not the case with Zn. In this work, the stirred tank bioreactor acid leaching employing bacterial Fe3+ sulfate solutions was studied, with ferric sulfate being a product of Fe2+ biological oxidation and not the chemical reactant adding of Fe3+ sulfate. Acidithiobacillus, Sulfobacillus, and Leptospirillum bacilli were employed in Fe2+ biooxidation. Temperature, pH, Eh, S:L ratio, leaching time, and Fe3+ concentration in the source leachate as the process controls were considered. As demonstrated, the process employing biologically regenerated ferric sulfate proved to be more efficient than conventional chemical leaching. Under the optimum conditions, the proportion of Cu extracted into leachate during 2 hours was 79.1%, and that of Zn 27.2%. Precipitation of high-grade Cu sulfide served to extract the metals from the leachate, and Cu extraction was 99.7%. All in all, 23.2% Cu, 0.03% Zn, and 0.02% Fe was returned into the pyrometallurgical process. Keywords: slag flotation tailings, copper leaching

Sep 1, 2012

By Mingfei He, Xianyang Qiu, Hongling Wang, Yude Gao, Qingbo Meng, Xiaoping Xu, Hao Bu, Guosheng Wang

"By the “HGMS-gravity separation-Flotation” combined technology, a Ta-Nb-Sn concentrates with the grades of Ta2O5 10.00%, Nb2O5 9.13% and Sn 42.62% at the recovery of 44.73% , 9.13% and 14.62% respectively , a Li concentrate with Li2O 3.11% at the recovery of 51.83% and a feldspar product are obtained. All the value elements are recovered. INTRODUCTION Tantalum and niobium widely used in electronics, atomic energy, aerospace and chemical industries with the advantages of high melting point, good ductility, low vapor pressure, strong corrosion resistance and high thermal conductivity are important strategic resources which occupy a special position in rare metals (Crockettand, 1993; GAO and Zou, 2004; LI and HUANG, 2012). China's tantalum and niobium resources are poor, and most of them are low grade, fine grain size, complex composition, and polymetallic associated with refractory mineral resources (GAO and Qiu,2013; Liang and Li, 2016). The Yifeng Lion Ore containing lithium and other rare metals (tantalum, niobium and tin) is an important lithium polymetallic deposit in China Jangxi province. While extensive previous studies have settled on the recovery of lithium minerals by flotation only for the extremely low grade of Ta, Nb and Sn. The regular gravity concentration is used, and the recovery of tantalum niobium is low. This paper sets out to investigate a combined flowsheet of “high gradient magnetic separation (HGMS),-gravity separation-flotation” to effectively comprehensively recover the Li, Ta, Nb, Sn and the feldspar resources in the Yifeng Lion Ore.ORE PROPERTIES Chemical analysis The run of mine comes from Jiangxi Yifeng Lion ore. The main elements of the ore chemical analysis results shows in Table 1. From Table 1, the grades of lithium and rubidium are relatively high, but the grades of tantalum and niobium are lower than the industrial grade; feldspar with high content of potassium and sodium and low content of iron can be used as high-quality ceramic raw materials."

Jan 1, 2018

By W. M. Zeng

A mixed culture of moderately thermophilic microorganisms was enriched from Acid Mine Drainage (AMD) samples collected from several chalcopyrite mines in China,which can leach copper from chalcopyrite effectively. Its tolerance to chalcopyrite was brought up to 80 g/L after being adapted to gradually increased concentrations of chalcopyrite. The effects of several leaching variables on copper recovery in Stirred Tank Reactor had been investigated. The ore contained chalcopyrite (62.2%) and galena (25.6%) as the main sulfide minerals. The results of the tests show that it is possible, operating at 8% of pulp density to attain copper extraction of 75% in 44 days. The leaching rate of chalcopyrite tends to increase with the dissolution of total iron. Microscopic counts of microorganisms in the solution tend to be higher at low pH range. Furthermore, the analyses of leached residues indicate that the passivation of this chalcopyrite is mainly due to the formation of a mass of jarosite and anglesite (about 48.3% and 21.7% in residue respectively), other than elemental sulphur layer. The bacterial community composition was analyzed by using amplified ribosomal DNA restriction analysis (ARDRA). Two moderately thermophilic bacteria species were identified as Leptospi-rillum ferriphilum and Acidithiobacillus caldus, with different proportion in the bio-pulp, 67% and 33%, respectively.

Jan 1, 2014

By Ataollah Nosrati

Agglomeration of fine mineral particles is an important step in heap leaching processes employed for a cost-effective hydrometallurgical extraction of value metals from low-grade ores. In this study, the effect of acidic binder composition and feed ore particle size on binder dosage requirement and isothermal, batch agglomeration behavior of siliceous goethite nickel laterite has been investigated. Agglomeration tests performed with tap water and 30, 44 and 98% w/w H2SO4 solutions as binders revealed the key role of binder formulation in controlling ore particle wettability, nucleation and granule growth behavior. Both lower binder acid content and higher dosage led to greater wetting, nucleation and granule growth rates. Variation of feed ore fine/coarse particles? mass ratio dramatically impacted on binder dosage requirement for effective particle wetting, nucleation, and growth agglomeration behavior. Increasing fine (-150 µm) fraction mass content in a -2 mm feed ore, led to higher binder dosage requirement and enhanced nucleation, however the overall agglomeration rate/granule size growth decreased. In contrast, the presence of coarse (5 ? 15 mm) particles in feed ore led to (i) lower binder dosage requirement, (ii) enhanced initial agglomerate size growth rate, and (iii) reduced coalescence. For dry agglomerates of similar sizes, competent coarser feed particles led to remarkably higher compressive strength than did finer feed particles. Microstructure analyses indicated that the granules containing coarser particles exhibited a distinctive, competent core/shell (fines) structure which led to their structural reinforcement. The appropriation of the findings for optimizing agglomeration behavior for enhanced heap leaching of complex, low grade laterite ores are discussed in this context.

Sep 1, 2012

By Q. J. Liu

The flotation circuit and the reagents of the all-sliming flotation about low grade and hard operation on zinc oxide ore are researched in the paper. The results indicated that there are many types of zinc minerals in this ore, and the composition is very complex. They include hemimorphite, smithsonite, hydrozincite and so on. The ore is seriously sliming. In light of the ore properties, three kinds of flowsheets have tested. They are gravity concentration (cleaning tables), flotation, combined process of gravity concentration and flotation. The test showed that the recovery of zinc is only 17.08% in the gravity separation. In combined process of gravity separation and flotation, the recovery of zinc concentrate is close to 70%. But the flow-sheet is complex and hard to control in the production. The floatation circuit is feasible. In the test, it pay attention to investigate the new combined reagent which is used in selective all?sliming flotation process. The effects of slime are eliminated by the multi-loop treatment of middling. In flotation, the final recovery of concentrate is 88.76%; the grade is 29.50%. The recovery of physical ore is 93%; and the recovery of -10mm fraction is more than 65%.

Jan 1, 2014