Search Documents

By Carlos de F. Gontijo

The flotation of quartz particles was studied over the particle size range from 0.5 µm to 1000 µm and for advancing water contact angles between 0º and 83º. Flotation was performed in a column and in a Rushton turbine cell. Particle contact angle threshold values, below which the particles could not be floated, were identified for the particle size range 0.5~1000 µm, under different hydrodynamic conditions. The flotation response of the particles, either in a column or in a mechanically agitated cell with a similar bubble size, was comparable. Turbulence plays a role, as does bubble-particle aggregate velocity and bubble size. The stability of the bubble-particle aggregate controls the maximum floatable particle size of coarse particles. For fine particles, the flotation limit is dictated by the energy required to rupture the intervening liquid film between the particle and bubble. Flotation of very fine and large particles is facilitated with small bubbles and high contact angles. These results greatly extend our earlier observations and theoretical predictions.

Jan 1, 2014

By M. Ito

Cobalt-rich ferromanganese crust and nodule ores from seamount areas contain volcanic and sedimentary rocks as substrate or nuclei. These ores require mineral processing to remove the sub-strate/nuclei rock before smelting. This paper reviews experimental results of previous investigations. Observations and analysis of 10 samples from different localities were carried out and it was found that the liberation ratio of crushed product was high even at coarse size fraction, 0.5mm to 4mm. Experimental and calculated results in the smelting stage confirmed that the separation product satisfies the standards of the subsequent smelting process if the substrate/nuclei rock is removed from the 0.5mm to 4mm fraction with high separation efficiency. There was a density difference between the substrate/nuclei rock and the ferromanganese component. Thus the coarse sized sample was treated with gravity separation; air table separation was used as a dry method and jig separation as a wet method and high grade values with high recoveries were obtained by both kinds of gravity separation.

Jan 1, 2014

By K. Saberyan

Zirconium and hafnium are two important elements in nuclear industries. Zirconium is used in fuel rod for its low neutron absorption. Hafnium should be separated from zirconium, because it has higher neutron absorption cross section. In this research, separation process of the mentioned elements from (Zr+Hf)Cl4 mixture produced in the Zirconium production plant (ZPP) of Iran (Esfahan) was studied employing solvent extraction method in the nitric acid medium by using tributylphosphate (TBP) as solvent, and kerosene as diluent. The effects of nitric acid, sodium nitrate and amount of extractant, zirconium concentration in aqueous phase, phase ratio, agitation time, and mixer agitation rate were investigated on the separation process. The process was optimized at 5 M nitric acid, 1 M sodium nitrate, 60% (v/v) TBP. The optimum values for phase ratio, agitation time and agitation rate were 1.5 min and 500 rpm respectively. In this condition, the zirconium extraction efficiency, and separation factor were 65.1% and 205.59, respectively. Finally, we accessed to nuclear grade in this research.

Jan 1, 2014

By A. Shandilya

ACC ECOSAND is finely powdered crystalline silica, which can replace natural sand usage in concrete and plasters. ACC ECOSAND ensures a comparatively denser concrete than those made only with natural sand and / or quarry fines / Manufactured Sand (Artificial Sand). Moreover, there is a significant gain in compressive strength (10-15 %) & durability in concretes (Reduced chloride conductivity leads to increased durability). ECOSAND is a by-product of froth flotation of limestone. At ACC Madukkarai cement works, Coimbatore, Tamilnadu, full-fledged mineral beneficiation process is adopted to enhance the usage of flotation reject in concrete and plasters. Optimum level for usage of ECO-SAND is 50%. With 50% usage of natural sand+50% ECO-SAND in concrete mix, 1 day, 3 day, 7 day & 28 day compressive strength is increased by 30.1 %, 22.6 %, 15.1 % & 11.0 % respectively and with moderate chloride permeability as compare to 100% Natural Sand. Keywords: froth flotation process, beneficiation studies, Denver cell, ECOSAND, siliceous material, durability & compressive strength, RCPT

Sep 1, 2012

By Valentin V. Shatalov, Irina V. Pastukhova, Alexander V. Kurkov

"We have developed a technology to improve the quality of low-grade concentrates containing minerals of tantalum, niobium and tin on the basis of given conception by the way of improving selectivity and using certain reagents composition. The basic collector presents a traditional or complex-forming collector used together with organic diphilic reagents – the secondary reagents regarding the basic flotation regiment, capable of forming associates with the main collector on the surface of the mineral, thus altering the interaction energy. In the given process the main collector is the fraction of hydroxamic acids C7-C9, the reagent of the secondary action – sulphosuccinamate, which added in moderate concentrations range provides for a synergistic effect.We have determined the parameters of the process stability and necessary modifying reagents for a selective recovery of tantalum, niobium and tin minerals from refractory products. Variants have been studied where the main collector and the secondary action reagent were substituted with some more efficient flotation reagents. A possibility of a more flexible reagent compounding for the process has been shown. The flotation process is highly stable regards the saline composition of the liquid phase in the pulp. It can operate under conditions of the complete water recycling with the total salt content up to 12 kg/m3, iron up to 1.2 kg/m3.The given results consider the efficiency testing of the suggested technology for the gravitation products, which were obtained from ores of various genesis and contain large quantity of the most refractory minerals, such as topaz (80%), gamet (55%), tourmaline (30%). High selectivity of the process has been registered with the metal recovery about 92-98%, which appears to be similar to hydrometallurgical operations under certain conditions."

Jan 1, 2003

By João Queiroz, Cristian Marquez-Sarmiento, Luiz Teixeira

The removal of various metals from process waters and effluents is usually done by precipitation of the corresponding hydroxide. Manganese however is one metal that does not respond efficiently to that approach. It may be seen in its eH X pH diagram that the way of oxidation to Mn IV rather than hydrolytic precipitation of the Mn II ion as its hydroxide, is the way to efficient precipitation of Mn in the pH range 6 to 10. We studied the use of oxidants O2; NaClO; H2O2; Caro´s Acid (H2SO5) and the combinations of O2 or H2O2 with Na2S2O5, and H2O2 with NaClO, for the oxidative precipitation of Mn from synthetic solutions starting with 10 mg/L Mn, at 25 oC. In adequate conditions, which include pH > 8, it is possible to reach final [Mn] less than 0.1 mg/L in 60 minutes of reaction time.

Jan 1, 2014

The flotation efficiency of magnetic concentrate of the Anhui hematite ore, which includes a great quantity of iron-bearing silicates, has been studied through reverse flotation test with a new type of collector Fly-102. The results indicate that collector Fly-102 has a strong adaptability to the variation of temperature, when the flotation temperature is in the range of 10? to 35?, using collector Fly-102 can obtain good flotation indexes. Collector Fly-102 has a strong adaptability to the variation of the slime contents and grades of the flotation samples. When the content of slime and the grade of the flotation feeds are 30% and 55.63% respectively, under the condition that the temperature is 15?, the open circuit flotation test was carried out with collector Fly-102. After one-stage roughing, one-stage cleaning and two-stage scavenging, a better result is got, the grade of iron concentrate reaches 67.12%, and the recovery of iron concentrate comes up to 84.15%.

Sep 1, 2012

By P. Somasundaran

While sustainability itself needs to be redefined in a selfless way, methods of measuring and optimizing it also need to be reformulated. Gone are the days when we had the luxury of abundant resources and the freedom to extract values in self-centered ways. In the past, focus has been mostly on reagent performance, processing operations, and upgrading of tools to maximize rather than optimize value extraction from the earth's crust. Today we as extractors face a new set of challenges that include value separation from low quality resources including wastes, but within the energy, environment, and societal constraints. Development of such technology depends on understanding the role of entities and concepts such as bio-molecular interactions at surfaces, forces involved in inter-granular versus intra-granular fracture in new fragmentation methods, robotic in-situ or extraterrestrial mining, exploiting new membrane and nano technology, use of new sensors and actuators for detection and separation and computation capabilities for faster and economical processing. Equally importantly, we need to communicate with everyone what we foresee and anticipate when we extrapolate the type-performance-cost relationship of ores to the era ahead of us and establish viable schemes for ecological survival. Keywords: sustainable mineral extraction

Sep 1, 2012

By H. Breuer

Mineral processing is characterized by a constant adaptation to changing raw materials and market conditions. It is the link between the mined raw material and a marketable product. As a lot of high grade reserves are exploited, a steady deterioration of raw material quality can be observed. At the same time, the customers´ requirements for product purity and consistent quality increase. Indian iron ores are characteristically friable in nature that results in generation of sizeable quantity of fines (0-10mm) every year during various stages of mining and processing in the country with grade varying from 50-60% Fe(T) and are high in silica/alumina (Al2O3 5-8%). The fines generated cannot be directly used for iron making (blast furnace/DRI units) in the country due its physical and chemical properties; therefore, large portion of it gets exported or dumped. Value addition to iron ore fines through various activities such as beneficiation & palletization is the need of the hour, which will not only be economically beneficial to the mining sector in the long run but also generate value addition & employment opportunities. Incentives may be given for adopting latest technologies for direct use of fines in iron making by agglomeration of fines in the form of Pellets and Sinters, as fines forms considerable part of iron ore resources. Due to selective mining, although the iron content of the ore is high but the alumina(Al2O3) content in iron ore is also significantly high which demands for beneficiation as high alumina will create problem during iron making like higher fuel consumption, poor quality of slag produced, reduced productivity of B.F. all mineral has been engaged in hematite iron ore beneficiation with its gravity and magnetic separators since the mid-nineties. The delivery of jigs started for the upgrading of iron ore for its utilization in a Direct Reduction Plant in Australia. Since then, various other installations with jigs for lumps and fines as well as upstream separators for fines are in operation in Brazil, Australia, India and South Africa. Low grade run of mine and/or dump ores are being processed with alljig®-, allflux®- and gaustec®-WHIMS as the core equipment. The article describes the technology in use, the characteristics of various iron ores and the product qualities achieved. The data presented shows the specific advantages of jig application on iron ore upgrading due to the possible high gravity cuts and the easy and low cost operation. The allflux®- technology provides the big advantage of high capacities and a two-step process, both in a single unit. The gaustec®-wet high intensity magnetic separators offer high capacity in combination with unsurpassed process flexibility. Keywords: iron ore, gravity separation, jig, upstream classifier, wet high intensity magnetic separation (whims), pelletization, sinteringMineral processing is characterized by a constant adaptation to changing raw materials and market conditions. It is the link between the mined raw material and a marketable product. As a lot of high grade reserves are exploited, a steady deterioration of raw material quality can be observed. At the same time, the customers´ requirements for product purity and consistent quality increase. Indian iron ores are characteristically friable in nature that results in generation of sizeable quantity of fines (0-10mm) every year during various stages of mining and processing in the country with grade varying from 50-60% Fe(T) and are high in silica/alumina (Al2O3 5-8%). The fines generated cannot be directly used for iron making (blast furnace/DRI units) in the country due its physical and chemical properties; therefore, large portion of it gets exported or dumped. Value addition to iron ore fines through various activities such as beneficiation & palletization is the need of the hour, which will not only be economically beneficial to the mining sector in the long run but also generate value addition & employment opportunities. Incentives may be given for adopting latest technologies for direct use of fines in iron making by agglomeration of fines in the form of Pellets and Sinters, as fines forms considerable part of iron ore resources. Due to selective mining, although the iron content of the ore is high but the alumina(Al2O3) content in iron ore is also significantly high which demands for beneficiation as high alumina will create problem during iron making like higher fuel consumption, poor quality of slag produced, reduced productivity of B.F. all mineral has been engaged in hematite iron ore beneficiation with its gravity and magnetic separators since the mid-nineties. The delivery of jigs started for the upgrading of iron ore for its utilization in a Direct Reduction Plant in Australia. Since then, various other installations with jigs for lumps and fines as well as upstream separators for fines are in operation in Brazil, Australia, India and South Africa. Low grade run of mine and/or dump ores are being processed with alljig®-, allflux®- and gaustec®-WHIMS as the core equipment. The article describes the technology in use, the characteristics of various iron ores and the product qualities achieved. The data presented shows the specific advantages of jig application on iron ore upgrading due to the possible high gravity cuts and the easy and low cost operation. The allflux®- technology provides the big advantage of high capacities and a two-step process, both in a single unit. The gaustec®-wet high intensity magnetic separators offer high capacity in combination with unsurpassed process flexibility. Keywords: iron ore, gravity separation, jig, upstream classifier, wet high intensity magnetic separation (whims), pelletization, sintering

Sep 1, 2012

By G. Kumar

Water for domestic consumption is an essential right of society, which must be over secured. Water reclamation and reuse provides a unique and viable opportunity to augment traditional water supplies. As a multi-discipline and important element of water resource development and management, water reuse can help to close the loop between water supply and wastewater disposal. Effective water reuse requires integration of water and reclaimed water supply functions. During the coal mining activities, large quantities of water get contaminated and loses its potability characteristics. On an average, in coal mine operation, each coal mine discharges effluents at a rate of nearly 0.5 MGD and thereby wastage of nearly 50 MGD of water takes place per day from the famous Jharia Coal Field of the Dhanbad District. In this paper, attempt has been made to control the extremely high turbidity of mine waste water by using different coagulants and it is observed that ferrous sulphate is the most effective coagulants followed by alum, ferric sulphate and lime. Also combinations of coagulants are used for getting the optimal results. Further steps were also discussed to make this water potable and a scheme of low cost water supply system of mine waste water has been suggested under the Water Management Strategies. Keywords: potability, turbidity, coagulants, water management strategies

Sep 1, 2012

By Q. W. Jiang

This paper presents a new process for producing industrial magnesium sulphate using waste water from titanium white plant and magnesium oxide from calcinations of magnesite ore as raw materials. With the laboratory experimental equipment, the waste liquid and magnesium dioxide react effectively at ambient temperature and under atmosphere pressure. Via the press filter, a clear liquid predominately containing magnesium sulphate is obtained. It is further evaporated and crystallized by cooling, separated by centrifuge and dried. Consequently a high quality of industrial magnesium sulphate is achieved as the final product. In the course of process, as the majority of valuable component (SO42-) is recovered in the final product, most of impurities from waste acid is being removed into the by- product. With the simple operational process, it is possible for titanium dioxide plant to resolve the environmental problem completely and benefit from the industrial magnesium sulphate product as well. The filter cakes containing valuable elements such as Mg, S, Fe, Mn, V, Ti are by-product proposed to be used for manufacture of agriculture fertilizer particularly for peanut planting.

Jan 1, 2014

By Y. D. Gao

A new technique has been developed for comprehensively recovering tantalum niobium tungsten ore by adoption of stage grinding, stage separation, combination of flotation and gravity separation, gravity separation for coarse particles, flotation for fine ones, combination of ore-dressing and hydrometallurgy. The new type and high efficiency combinative collector mainly composed of benzyl hydroxamic acid is firstly used to treat tantalum niobium and tungsten slime, besides the new type equipment for gravitational separation ?YTF-C shaking table for fine particles is adopted to treat flotation rough concentrate, hence having notably enhanced both recovery and concentrate grade of fine tantalum niobium and tungsten minerals. The commercial test obtains the tantalum concentrate assaying Ta2O5 31.98% with recovery 43.44% and tungsten product assaying WO3 89.40% with recovery 76.02%. The developed technique provides a reliable approach and an effective way for comprehensive utilization of lean fine complex refractory tantalum niobium tungsten ore resource.

Jan 1, 2014

By V. Hema

Granular materials are widely used in process industries, such as chemical, pharmaceutical, cement, food, detergents, and fertilizers. Mixing, blending, calcining, reduction, heating, and granulation of these materials are frequently carried out in rotating cylinders. In all of these processes, the mixing and segregation of these granular materials is important as this controls the secondary phenomena in the rotating kiln such as heat transfer to the material. A significant amount of work is available in the literature but to date these efforts have not been able to capture the important parameters affecting the mixing and segregation in rotating kilns. In addition, the range of parameter values studied so far is rather limited. Simulations of granular materials are based on either discrete elements or continuum models. The discrete element methods (DEM) combine semi-empirical models for the inter particle interactions with the equations of motion from classical mechanics to simulate the explicit paths of all granules in a rotary kiln, thus yielding realistic predictions of the mixing process. This approach is very demanding computationally, which strongly limits the number of granules and the number of revolutions in a simulation. Continuum models dispense with the discrete particles and can therefore be scaled up more easily. But the constitutive relations that serve as the foundation for continuum modeling are difficult to come by, and often only applicable to specific systems and conditions. Here we have chosen DEM simulation for investigating the mixing and segregation behavior of granular materials in a rotating cylinder. This work is directed towards demonstrating the capability of the prediction of the mixing and segregation behavior of granular materials in a horizontal rotating cylinder through discrete element simulation. Further the effect of particle size and rotational velocity on the mixing and segregation behavior is investigated. The simulation results are quantified in terms of mixing index, mixing rate, segregation index and percolation index. Keywords: DEM simulation, granular mixing

Sep 1, 2012

By Michel Brissette, Shaheer Sanuri, Veroljub Mihajlovic

"The main purpose of geometallurgy is to improve the mine planning by mapping hardness and throughput into the mine block model using geostatistics to eliminate the large production fluctuations caused by the ore hardness variability coming from different parts of the pit. However, not all grinding testwork available commercially can be applied to geometallurgy because of large amount of sample required and the associated cost per test. Geometallurgy is now being used in designing grinding mill but as the mining project progress, the accuracy of engineering must improve from 30-35% during the scoping study to 10-15% at the bankable feasibility stage and less than 5% for Engineering Procurement and Construction Management. For SAG milling, the SAG Variability Test (SVT) is an abbreviated version of the standard SAGDesign test developed for this geometallurgical need. The same amount of ore than the original test is ground for three cycles into an open batch SAG test and then the SAG pinion energy is predicted to the standard end point of 80% passing 1.7 mm. For ball milling, a Bond Variability Test (BVT) was also developed using the SAG ground ore from the SVT. The Bond ball mill grindability (Gpb), corresponding to the average of the net grams per revolution from the last three cycles of the Bond test, is also predicted from the third cycle. The relative error for both the predicted SAG ore hardness (WSVT) and Bond Work Index on SAG Variability ground ore (Sv-BVI), in kWh/t, averaged 5.5% and 3.8% respectively compared to the SAGDesign testwork values and are within 7% and 10% respectively from plant benchmark and within 7% from the samples sent to all partner laboratories. Both tests can be continued to measure the true hardness necessary for mill sizing. This article discusses the development of these two new tests, SVT and BVT, their potential use and accuracies in any geometallurgical program."

Jan 1, 2014

By I. H. Mukhametshin, E. N. Baranova, I. B. Fadina, E. A. Ashirbaeva

The purpose of the research is the development of a complex of solutions for the maximum extraction of non-ferrous and precious metals from persistent mineral raw materials by heap bioleaching from spent heap leaching (HL) stacks. Methodical recommendations for assessing the suitability of primary and technogenic refractory mineral raw materials for heap bioleaching are developed. Active associations of microorganisms have been created for the conversion from various types of ores to the solution of S, Fe, As, Sb, Cu, Zn, Mn, Ni, Mg, P and other elements, as well as methodologies for their storage, immobilization and preparation of bioreagents in industrial conditions. On a pilot scale, tests were carried out on samples weighing 15-17 thousand tons of refractory gold-sulphide ores (more than 50% of gold is associated with sphalerite), gold-quartz ores with colloidal gold (74% associated with quartz and pyrite) and gold-silver ores with elevated copper and zinc content (1.5 and 3,5%, respectively), as well as man-caused material lying for 4-5 years of spent quarry material of oxidized gold-silver ores. In the pilot-industrial tests of heap bioleaching of gold-sulfide ores, gold recovery of 84-85% and silver was achieved to 89-90%, the possibility of obtaining high-yield solutions of copper and zinc, suitable for hydrometallurgical processing, from gold-silver ores, and the possibility of obtaining waste with a dump content of valuable components, suitable for deep disposal in the construction industry. When comparing two technologies for processing refractory ores after biooxidation under HL conditions, when 1000 tons of ore processed by the bioreagent were re-milled from a size of 40 mm to 0.1 mm and cyanated under the conditions of the factory process, the same results were obtained for gold recovery (85%) and silver (90%), as with the heap version. The copyrights of the development are protected by a patent.

Jan 1, 2018

By Rebecca Hope, Derick Moolman, Frikkie Malan

"Despite the lip service that has been paid to pro-active plant maintenance processes over recent years, a significant portion of maintenance in industry is still reactive. The business driving force to prevent expensive production opportunity costs arising from “break-down maintenance” is obvious. Various benefits can be derived from successfully deploying remote equipment diagnosis technology and associated business processes.From an end-client’s viewpoint these include the ability to predict and take actions to prevent equipment breakdowns, increasing the lifetime of equipment by responding to appropriate operating instructions and therefore improving the return on capital expenditure. Better planning and scheduling of maintenance priorities and resources with performance measures like an Equipment Health Index are also possible. The knowledge that a qualified supplier engineer is constantly in touch with the operating conditions of their equipment, albeit remotely, is more than a comfort, and can be translated into quantifiable cost savings and improved supplier service levels.This paper analyses the reasons for the inadequate level of pro-active plant maintenance practice in industry today, and presents a number of important criteria in selecting appropriate solutions to this problem. A case study of a specific real-time, remote equipment management application is presented."

Jan 1, 2003

By I. Kairyakov

The present paper is about the restoration of the molybdenum production in the floatation plant of Ellatzite-Med AD in Bulgaria. The process, based on a working design, includes the construction of a new floatation molybdenum section in the existing molybdenum department of the Floatation Plant using the so called Vemco inert-gas floatation machines, made especially for the molybdenum floatation. While in the ordinary floatation machines, block impellers create suspension of the air, sucked from the atmosphere with the slime particles of the concentrate, which creates conditions for oxidizing the reagent, Vemco inert-gas floatation machines are covered with hermetic lids and the air inside the chamber is used. The technology, suggested by Geotechkoper Ltd. for making the working project, employs special machines from Dor Olliver Aimco, suitable specifically for molybdenum floatation in order to reduce the oxidizing of the reagent sodium hydrosulphate. Also the transport of the chamber product is done in hermetic conditions as the molybdenum flotation is done in two floatation rows and refining operations 3 to 8 are placed in the second row. Thus in the basic molybdenum floatation together with the first and second refining operations, which are hermetically closed, an ambient condition with low content of oxygen is created, that is about 8% for oxygen and about 92% of nitrogen, in which the oxidizing process is extremely reduced. This in turn results in reducing the consumption of the reagent depressor ? sodium hydrosulphate. In that way there is an improvement of the economical indices of the molybdenum production.

Jan 1, 2014

By P. Saha, D. M. Chakrabarti, National Metallurgical Laboratory, P. Bhattacharyya, B. R. Sarkhel

The estimated reserve of the phosphatic soils at the Sukulu hills region of Uganda upto a depth of 60 meters is of the order of 200 million tonnes and analyses 10-12% P2O5. A 5-tonne sample of the phosphatic soil was received at the National Metallurgical Laboratory (NML), India for beneficiation studies. The ore occurred as a naturally degraded soil deposit and the slime contained earthy lateritic minerals which made it extremely sticky. Microscopic examination revealed the presence of limonite, magnetite (martitised), hematite and goethite as major minerals along with apatite and quartz. Presence of clay was indicated by earthy smell on moistening the sample. It was observed that getting rid of the slime was as important for adequate beneficiation of the ore, as it was difficult. Earlier studies on samples of the same ore at the NML and abroad established that it was necessary to pass the ore through a series of three stages of desliming, each consisting of a step of rigorous attrition scrubbing followed by hydrocycloning, for effective elimination of the sticky slimy coating which stubbornly adhered to mineral grains. Studies were carried out at the NML in two phases to develop a flowsheet for beneficiation of the phosphatic soil. In the first phase, reproducibility of the results obtained by employing a flowsheet developed abroad was confirmed along with suggesting some modifications of the flowsheet. Then 200 kg. of concentrate was produced following the recommended flowsheet for evaluation of its suitability for production of fertilisers. To remove the limonitic slimy coating, which stubbornly adheres to the other mineral grains, it was necessary to subject the ROM ore, after screening out the +840 micron size fraction which contained only 1.75% P2O5 , to three stages of hydrocycloning each preceded by attrition scrubbing. Then only conventional beneficiation techniques could be effectively employed to upgrade the ore.

Jan 1, 2003

By S. V. Petrov

In recent years, heap leaching of gold is becoming wide spread due to low capital and operational costs that allows economically feasible processing of low-grade and cut-off grade ores. Currently, over 30 heap leach projects are operated in Russia. Some of the deposits treated by heap leach methods are almost depleted. Therefore, they will soon require spent heaps detoxification and reclamation. Traditionally, spent heaps are detoxified by chemical treatment. This process is characterized by relatively high kinetics and requires expensive reagents and additional equipment. The main disadvantage of this process is secondary contamination of the solutions by products of detoxification reactions and impurities contained in reagents. If there is enough time, spent heaps can be detoxified by natural degradation. The advantages of the proposed method are low operational costs due to use of existing heap leaching facilities and eliminating the need for chemicals for spent heaps detoxification. Residual concentrations of cyanides and thyocyanates in liquid phase (wet ore) of spent gold ore heaps after detoxification were 0.2~0.3 mg/L. Heavy metals were almost completely removed. The method was successfully used for detoxification of spent heaps at two gold mines.

Jan 1, 2014

By A. F. Usov

The paper is concerned with an analysis of the experience gained in development of special electro-technical installations applied in electric-pulse destruction of materials. A principle scheme of an electric electric-pulse installation is given, and electric circuit variants of its blocks made on various element bases are discussed. Also assessed are some ideas to further improve the technical and economic characteristics of the equipment.

Jan 1, 2014