Search Documents

By David Miller

"The biggest concern about using soil mixing is the inability to observe physically the final product, which has led to a lack of confidence about what is in the ground. After all, you can’t see it and you can’t taste it and you can’t smell it, so are you sure it’s soil mixing? In addition, there are variations in techniques, tools and monitoring that have led to additional skepticism and the desire to “elevate” the product. This skepticism is why the industry is so scrutinized even when there are other technologies being used that do not experience nearly the same level of scrutiny. With other techniques, even with a slurry wall, you can see the backfill before it goes into the ground, and drilled piers have careful evaluation of the concrete mix even before placement into and verification of the open hole. Essentially, you get control over the final material. There is less control in soil mixing, and it’s very dependent on in-situ conditions. These factors make it difficult to rely solely upon installation parameters, quality control (QC) and verification tests. At some point, you may need to apply some engineering judgment.Start at the BeginningThe availability of sufficient and accurate geotechnical data (soil type, heterogeneity, shear strength parameters, variability, etc.) is important in establishing the material that will be drilled. This data will also help in determining the proper mix design to achieve the desired soil cement properties. Many factors must be considered when designing the mix and the mixing program, including any debris in the ground, different soil properties and varying moisture contents.Each of the various factors affect the final properties of the soil cement, so it really takes careful planning and evaluation of the mix design through iterations by looking at the soil types and adjusting the mixes. Clay is going to behave very differently than sand in both mixing efficiency and final properties. That is, the presence of clays results in more difficulty in achieving higher strengths and to physically mix the soil and the binder, whereas the presence of sands results in more difficulty controlling the final permeability."

Jan 1, 2017

By Peter J. Jancich

This paper describes the installation of high capacity Augered Pressure Grouted piles which support structural loading from a four level parking garage in west-central DuPage County, Illinois. The subject site is characterized by a variable glacial geology which presented, to the designer, a number of problems with respect to analysis and prediction of pile capacities, and, to the contractor, the very real difficulties associated with estimating the costs of, and installing foundation units in highly variable subsurface conditions. 2. General Site and Subsurface Conditions 2.1 Site Conditions - The subject site is part of an overall 300 acre property. Topographically, the overall site is saddle shaped with higher elevations along north and south boundaries and a subdued, east-west trending swale centrally located. Elevation relief is on the order of 25-30 feet (7.6-9.2m).

Jan 1, 1991

By John P. Turner, Mark Jen, Bobby Daita

"The Port Authority of New York and New Jersey is replacing the existing Goethals Bridge built in 1928 which is deemed to be functionally obsolete. The replacement bridge will consist of a dual cable-stayed Main Bridge crossing the Arthur Kill with elevated approach spans connecting Elizabeth, New Jersey and Staten Island, New York. The main bridge towers are supported on a group of six nine-foot diameter drilled shafts that transition into a pier cap. The anchor and approach piers are supported on two column bents with each column supported on a single drilled shaft. The 4.5 to 10 feet diameter drilled shaft foundations have permanent steel casing to rock and socketed into bedrock. Subsurface conditions consist of Passaic Formation bedrock overlain by varying thicknesses of overburden soils. The foundation design assumes permanent casing extending a minimum 2 feet into the weathered bedrock. Rock socket lengths below the permanent casing vary between one to two shaft diameters based on the quality of the bedrock. The reinforcing design was based on AASHTO LRFD minimum requirements, force demands, seismic detailing requirements and also considering the continuity between the shaft and socket.The bridge is currently under construction with approximately 70 percent of the foundations installed. Several field conditions encountered at various stages of shaft construction between casing advancement and concreting required design and construction modifications. Based on the driving method and the quality of the bedrock, the tip of the permanent casing hit refusal either above or below the design elevation, requiring modifications to the drilled shaft design and its reinforcement. This paper provides an overview of the general subsurface conditions at the site and its impact on foundation design and discusses the detailing worked into the design to accommodate tip elevation variations, as well as various foundation design modifications in response to actual conditions encountered during construction."

Jan 1, 2016

By David Guy, John Stanbury, Gilbert Tallard

"In 2009, storm surge from Hurricane Sandy inundated the Bay Park Sewage Treatment Plant located at El. +4 to +12 (+1.2 to +3.6 m) in East Rockaway, Long Island, NY. With all systems down, raw sewage water mixed in the floodwaters. A recurrence of such an event being unacceptable, and in view of rising future sea levels, a flood protection project was developed by Nassau County with funding coming in large part from the federally funded Sandy Rescue Fund. Designed by Arcadis/Hazen & Sawyer Engineers J.V., the protection took the form of a perimeter barrier capable of withstanding future storm surge. Due to limitations imposed by property lines and existing facilities, a levee design with three different types of cross section was developed to adapt to each location, adding construction complexity. The Long Island subsurface is characterized by beach sand extending to great depth. The clay required for the core and levee cover therefore had to be brought in from out of state. A thin silty clay layer at El. -23 to -25 (-7.0 to -7.6 m) served as an aquitard. The under-seepage was reduced by a hanging cut-off wall designed as a vibrated beam thin wall and filled with a salt water resistant, low permeability, self-hardening slurry.INTRODUCTIONOn October 29, 2009, Hurricane Sandy hit New York City, with a devastating effect on the region. The low lying Bay Park Sewage Treatment Plant (STP) (Fig. 1) serving Nassau County on Long Island was submerged (Fig. 2). All basements and underground mechanical facilities were flooded (Fig. 3) and millions gallons of effluent were released into the waters of the nearby Hewlett Bay which connects via other small waterways to the Atlantic Ocean."

Jan 1, 2016

By A. Rod Kern, Michael A. McNicholas, Yaser Taheri

Deep foundations were required for construction of an 18,000 ft2 (1,672 m2) 4-story office building and an adjacent 23,750 ft2 (2,206 m2) 5-story parking garage in Queens, New York due to an existing uncontrolled fill layer ranging from 15-20 ft (4.6 - 6.1 m) in thickness beneath the building footprint. The geotechnical engineers for the project initially selected auger cast-in-place (ACIP) piles over driven piles to limit the impact of noise and vibrations on the surrounding neighborhood. Ultimately, drilled displacement piles (DDP) were installed since this method offered a more economical solution that would generate the required pile capacity with shorter drill depths and would also mitigate spoils volume. During installation of test piles by the geotechnical contractor retained for the foundation work, multiple unanticipated soil conditions were encountered that would adversely affect the constructability of the piles. The existing fill contained significantly more natural and manmade obstructions than expected and the underlying glacial soil became too dense to penetrate at shallower depths than anticipated. This paper discusses how these issues were overcome through pre-drilling and the use of detailed instrumented test pile data coupled with in-house engineering capability to proactively re-evaluate minimum pile lengths at any given location and keep the project on track. INTRODUCTION Geotechnical work in the New York City market presents soil conditions that can be highly variable and challenging due to the presence of uncontrolled urban fill placed over the native soils. Construction in this area can therefore pose many unforeseen challenges, even with detailed geotechnical analysis being performed at project sites. A case in point is a construction site in Queens, New York. The proposed site development consisted of construction of a 4-story office building with a footprint of 18,000 ft2 (1672 m2) and a stand-alone 5-level parking garage with a footprint of 23,750 ft2 (2206 m2), together with associated new pavements and utilities. The site is bordered by a mix of commercial buildings and residential properties on all sides. Depth of the uncontrolled nature of the fill extended up to 20 ft (6.1 m) below street grade. Given the significant cost associated with removal and replacement, deep foundations were recommended to bypass the unsuitable soils and support the structures at depth where good bearing material existed.

Jan 1, 2019

By Clarissa Aguiar, Seok hyeon Chai, Thamer Yacoub, Sina Javankhoshdel

Sheet piles are used as an excavation support for soil retention. They are interlocked systems to form a wall for earth support along with anchors to provide an extra lateral support in excavations. The earth pressure against a sheet pile structure is not unique for each soil, but rather a function of soil-structure system. Movements of the structure with respect to the soil are primary factor in developing the pressure and thus the problem becomes indeterminate. In order to model a sheet pile wall for the analysis, structural element/interface can be used for the sheet pile. However, the use of the structural element with soil model alone is insufficient to simulate this soil-structure system as it fails to capture the slip condition between the sheet pile and the retained soil. In order to capture this slip condition, an interactive element can be used between sheet pile and soil to allow slip to occur. There have been many case studies where this method was used to analyze the response of the retained soil. Numerical studies have shown a good agreement with experimental results, but this stiffness is often not a well-known parameter, due to its complexity in nature of interactive behavior between soil and sheet pile walls. Also, many case studies are carried out with twodimensional analysis of the foundation, where three-dimensional analysis may be more suitable in some practical applications. In this paper, the interactive behavior of the element between sheet pile and soil is investigated with case studies for staged excavation using sheet piles and anchors. Then, investigation of a three-dimensional model is carried out by comparing with two-dimensional analysis.

By Yazen Khasawneh, Osvaldo P. M. Vitali, Mohammad Nassim

The demand for renewable energy is growing as the conventional energy resources are becoming more limited and we are more conscious about the negative impact of conventional energy sources on the environment. Wind turbines technology is evolving in a fast pace, the towers are becoming taller, and the rotors are getting larger. The challenge is to maintain the Levelized Cost of Electricity (LCOE) as low as possible to ensure a sustainable and an economically feasible energy supply. Thus, the foundation systems for wind turbines should evolve to meet the increasing load demand, while reducing the LCOE. In this paper, an innovative foundation system for onshore wind turbines is presented. The new foundation system is the conventional P&H tensionless pier foundation (PHTP) with a reinforced concrete collar at the top of the pier. 3D FEM modeling was conducted to assess the benefits achieved by adding a collar at the top of the PHTP foundation. The numerical results show a significant performance enhancement of the proposed foundation system over the conventional PHTP foundation. The enhanced foundation system also has an economical advantage because the depth of the pier can be greatly reduced while maintaining a superior performance.

Sep 8, 2021

By Renzo D. Verastegui, T. C. Michael Law, Sitotaw Y. Fantaye, Alfredas Daugiala

"When completed, 520 Park Avenue will amend the Manhattan skyline and be one of the most prestigious high rise towers in New York City. The 52-story condominium building is located on a 60 by 100 feet lot on East 60th Street between Park and Madison Avenues. The geographically complex site is bounded by two fragile 5-story masonry buildings on the east and west, a mid-rise building on the north, and a New York City subway tunnel on the south. To add to this complexity, the ambitious development required 70 to 80 feet of excavation, mostly below groundwater level in highly permeable rock, to accommodate four levels of cellars. The new building also cantilevers 24 feet over a five-story historic building on the east. The limited footprint of the building coupled with large compressive and tensile axial loads, considerable base shear and over-turning moments, and the required deep excavation, presented unique foundation challenges. This paper describes how the challenges were solved with an innovative combination of permanent secant pile walls and drilled shafts.INTRODUCTIONThe project site is located at 45 East 60th Street, on the block bounded by East 61st Street to the north, East 60th Street to the south, Park Avenue to the east, and Madison Avenue to the west. As shown in Fig. 1, the site is surrounded on three sides by buildings sensitive to differential settlement. In addition, a NYCT underground subway structure lies below East 60th Street approximately 13 feet south of the site. The base of the subway structure is approximately 42 feet below the street.The project consisted of constructing a 52-story tall building. A portion of the superstructure cantilevers 24 feet over an adjacent five-story historic building. The underground construction for the new building involved a four-level basement, extending about 60 feet below ground surface. The excavation subgrade is much deeper than both the subway structure and the adjacent shallowly-founded building foundations."

Jan 1, 2016

By Michael Forrest, John Roadifer, Glen Gorski

"The Calaveras Dam Replacement Project (CDRP) requires large disposal sites to store excess excavated materials that could not be utilized for dam construction. Because of access restrictions during design, the disposal site rockfill toe dike area at the edge of the reservoir could not be explored to evaluate soil conditions. As such, the site had to be explored as part of the construction contract. Exploration revealed very soft clay and loose silty sand up to 40 feet thick that would not be able to support the rockfill dike at the toe of a large disposal site fill. Several alternatives were evaluated to stabilize these soils. Based on constructability, cost and risk considerations, cement deep soil mixing (CDSM) was selected as the preferred method of soil stabilization. The challenge was to design and construct the CDSM stabilization to minimize construction delays. A joint effort by the design engineer, construction manager and contractor achieved CDSM stabilization in about three months, from design through completion of construction. A rigorous quality control program included compression testing of both wet grab and cored soil cement samples to demonstrate that specified strength requirements were being achieved.INTRODUCTIONDisposal Site 3 (Figure 1) is one of the primary CDRP disposal sites having a height of 240 feet and a storage capacity of about 2,500,000 cubic yards. An approximately 40-foot-high rockfill dike at the base of the disposal site provides an erosion resistant toe for the disposal site. The rectangular foundation area shown in red was not able to be investigated during design because of access restrictions."

Jan 1, 2015

By Negin Khalili-Motlagh-Kasmaei, Paul O'Leary, Christopher J. Rothsiedl, Dimitar Ninesvski, Alexander Zöhrer, Vincent Winter

This paper presents the implementation of a digital twin for the vibro-replacement ground improvement process, as part of a digital construction site. The goal is to implement an evidence-based quality assurance for each produced element (column or point). The system uses a combination of planning data and real-time machine data collected automatically from construction equipment. In addition to the quality assurance, feedback is provided in a number of areas, e.g., condition monitoring of the equipment. The digital twin builds upon the real-time sensor and machine data, fused with metadata, to implement a digital model for the process. A hierarchical data evaluation, using rule-based Key Performance Indicators (KPIs), permits viewing of the spatial variation of data over the construction site. This permits the modelling of systematic variations in subsurface properties across the site, enabling the detection of anomalous individual elements, the diagnosis of their cause and the prediction of properties as construction proceeds over the site. All time-series data and KPIs are represented by standard classes of objects, leading to a generic coding of the data analysis; this minimizes the effort required to add additional sites and/or new KPIs. Examples are presented for a number of sites, where the system was used to identify anomalous columns.

May 1, 2022

By Mohini Patel, Jahnavi Parmar, Pranav R. T Peddinti

Expansive clays pose a variety of geotechnical problems. Although the admixture stabilization is proven to address their problematic swelling and shrinkage characteristics, the influence of unsaturated condition on the engineering performance of these soils needs further research attention. In addition, highly saline soils with high organic content would further alter their performance. A similar soil stratum was encountered at the Gulf of Cambay, Bhavnagar district, India. High salinity in the in-situ expansive soil of basaltic origin and the prevailing unsaturated condition, enforces the engineers to look out for possible soil treatment methods. In this regard, the present work attempts to analyze the unsaturated behaviour of this soil when fly ash is used as an admixture. A comparative study for stabilized and unstabilized mixes is performed in terms of their unconfined compressive strength, electrical conductivity, swell characteristics and California Bearing Ratio.

May 1, 2022

By Yazen Khasawneh, Osvaldo P. M. Vitali, John E. Agee, Mohammad Nassim

A 3D FEM modeling of a ground improvement solution for an ice rink slab with stringent differential settlement limits is presented. Due to the complexity of the geotechnical conditions and strict deformation requirements, a structural slab supported by micropiles was initially proposed. However, this solution was costly and alternative solutions using ground improvement techniques were investigated. The proposed slab is supported directly on rock at one end and on approximately 45-ft deep cohesive soils on the other end. The numerical simulations show that differential settlement would be larger than allowable, if the ice rink slab is supported directly on the existing subgrade. The addition of the ground improvement scheme with compaction grouting demonstrated that the anticipated differential settlements are reduced significantly and would become less than the allowable magnitude. This study demonstrates that the use of numerical simulations to study complex loading and geological conditions will help to optimize designs and may result on significant cost savings.

Sep 8, 2021

By Akshay Sakhuja, M. S. Karthika, R. Vignesh

"The bridge across River Mandovi in Goa is a cable stay bridge structure proposed parallel, along existing bridges for regulation and reduction of vehicular traffic; the entire bridge structure is supported on pile foundation socketed in rock. This paper describes drilling related issue encountered during execution of pile where bed rock varies considerably from factual geotechnical investigation, which in turn affected the productivity of bored piles socketed in rock then chiseling is advocated for rock socketing with limited number of blows based on penetration resistance of rock encountered or equivalent energy principle to increase the productivity and also to avoid excess chiseling which otherwise would have fractured the rock mass below and around the pile tip resulting in increased settlement of pile subjected to design load. Contractor decision on socket length have been taken without compromising either quality or productivity; the paper presents various procedures and the equipment involved for installation of pile in rock along with the conclusion related to termination of pile in rock and also the lessons learned in process.INTRODUCTIONPile foundations are generally used to transfer heavy loads in deeper bearing stratum if the soil immediately beneath the base of the foundation does not have sufficient capacity. The bridge across River Mandovi, Goa is in its construction phase as a part of the development plan of Goa State Infrastructure Development Corporation Ltd (GSIDC). The project was awarded to M/s. L&T Construction, Heavy Civil Infrastructure; subsequently the geotechnical investigation was awarded to M/s L&T Geostructures.The client has specified the foundation of the bridge as rock-socketed. Rock socketing is generally done to achieve higher bearing pressure through concrete-rock shear interface which many building codes permit. The design and construction of rock socketed pile foundation entails a detailed analysis and judgement on the superstructure loads, predominant geological conditions as well as ground water levels. The termination of pile is normally based on thumb rule of half to three times the pile diameter into the rock. Quite often the criteria is based on chisel penetration rate (Gandhi,1990) In fact, this is the key factor to consider appropriate and economical depth of embedment of pile into rock stratum which necessitates enormous understanding on the type and quality of rock strata encountered which may significantly influence the selection of suitable rotary rig for pile installation. Such criteria are site specific and also applicable for the set of equipment used for the particular project."

Jan 1, 2015

By Xavier Pita, Alexandre Pinto, António Cristovão, Rui Tomásio

"The cutter soil mixing technology was been applied in Portugal since the last seven years. The aim of this paper is to present the main design and execution criteria, related with both the cofferdam and foundations solutions, using soil-cement panels, reinforced with steel profiles, at the new Leixões Cruise Terminal, located at the Leixões Port, in Portugal. The Terminal building was built with one basement on a marine environment, over very difficult geological and geotechnical conditions, which demanded the use of some unusual and integrated geotechnical solutions. It is also pointed out the importance of the QC/QA, as well as the technical, economic and environmental advantages of the cutter soil mixing technique, comparing with same more conventional solutions.1 INTRODUCTIONThe construction of the new Cruise Terminal at Leixões, main gate of the Atlantic Ocean to the North of Portugal and Spain, as a consequence to the constant increase of the cruise traffic, was a challenge from both the geotechnical and structural point of views, mainly due to very difficult and unusual conditions, ranging from the geological and geotechnical scenario to the existent and under operation Leixões Port infrastructures, mainly the South break water, as well as the existent cruising boarding deck (Figure 1).According to the Terminal Project it was necessary to build one basement below the water table level, including several earth retaining structures in order to allow the excavation works on dry conditions leading to a global cofferdam effect. For this purpose soil - cement panels, using CSM technology, reinforced with steel profiles, micropiles (both for foundation and cut off effect) and the existent sheet piles were used. Also pointed out are the adopted special foundations of a very complex structure, including bored piles and micropiles (Figure 1)."

Jan 1, 2015

By Benjamin B. Buensuceso III

Crosshole sonic logging (CSL) is a popular quality assurance and quality control method used to examine the concrete quality of cast-in place deep foundations, though the evaluation of the results is subject to certain limitations. One such limitation explored in this paper is the occurrence of false positives, where signal anomalies indicated by CSL test results are not necessarily indicative of imperfections in the foundation that could affect its performance. A case study of false positives evaluated in CSL records in a major infrastructure project in Metro Manila is presented in this paper. A detailed desktop evaluation and results from complementary high-strain dynamic load testing and low-strain pile integrity testing were used to evaluate the significance of the suspected false positive signal anomalies from the CSL test results. Recommendations for the proper interpretation and evaluation of CSL test results in Philippine practice, given the method’s limitations and examples presented, are also shared.

Sep 8, 2021

By Frank J. Purcell

“Down The Hole” (DTH) hammer drilling is often necessary to advance the casing during pile construction where the test bores have determined difficult drilling conditions with obstructions such as boulders, cobble and glacial till. The use of compressed air to operate DTH hammers in foundation drilling has been a contentious point in many regions of the world due to its potential to disturb the ground around the pile being constructed. There are many examples of damage to adjacent building foundations where compressed air exiting the pile being drilled disturbed the subsurface around the building’s existing piles. This paper looks at the use of compressed air in DTH hammer foundation drilling and the move towards controlling the exhausted air to avoid over drilling the pile, causing potential damage to nearby piles. Simulated models of air flow penetration into the soil of different configurations of drill bits are discussed to highlight design changes employed to better control the air during the drilling process. A case study of the construction of a water-tight pipe pile wall for a building’s underground parking structure is studied to demonstrate the potential of DTH hammer foundation drilling where the air is fully controlled.

Nov 1, 2022

By Randy R. Williams, Brian W. Wilson, George M. Filz, Marina S. W. Li, Donald A. Bruce

"In-situ wet grab sampling and post-installation coring of soil-cement structures are typically carried out for Quality Control (QC) and Quality Assurance (QA) of deep mixing (DM) schemes. Wet grab sampling and testing is used to provide data to indicate that performance requirements are being met during production, in advance of coring, which typically occurs at 28 days or later, following installation. While unconfined compressive strength (UCS) tests from wet grab samples provide good production indicators, industry practice often requires that acceptance criteria of soil-cement structures be based on UCS results from representative core samples.This paper outlines the approach adopted for field sampling and QA/QC testing carried out in highly variable subsurface conditions at a site located in northern British Columbia (BC), focusing on postinstallation soil-cement coring and strength testing for an extensive deep mixing scheme. A discussion on suitable methods of coring soil-cement structures and appropriate selection of samples for testing that are representative of the in-situ soil-cement structures is provided. This paper also discusses the selection strategy adopted for verification of strength and modulus parameters used for design, providing spatial and time coverage, as well as the acceptance criteria implemented, and provides comparisons with published industry recommendations.BACKGROUNDAn extensive deep mixing ground improvement scheme was completed for the development of a Liquefied Natural Gas (LNG) Facility to be located in Bish Cove, BC, Canada. The deep mixing scheme was implemented to treat very weak native deposits in-situ to support two mechanically stabilized earth (MSE) walls up to 20 m (66 ft) high, and their associated bulk earthworks. Within the DM area, the subsurface conditions were highly variable, ranging from deep (up to 21 m (69 ft) thick) deposits of very soft to soft clayey silt to silty clay, overlying layers of dense to very dense gravelly sand to sand and gravel, to compact deposits of silty sand (up to 15 m (49 ft) thick), overlying dense sand and gravel. Bedrock was encountered beneath the granular deposits and generally comprised granodiorite with occasional andesite dykes."

Jan 1, 2015

By Arpana P. Sabu, Themis Vaxevanis, Sissy Nikolaou, Guillermo Diaz-Fanas

Geo-failures from extreme events (landslides, wild fires, earthquakes, floods, etc.) have increased exponentially in recent years around the world and within the USA. When catastrophic failures occur, they usually involve hundreds of fatalities especially in cases of unexpected triggering events, such as large intensity earthquakes or heavy flash floods. Protective actions against identified potential geohazards can mitigate the associated risks and the future occurrences and prevent these occurrences from becoming disasters, targeting the essence of resilience in geotechnical engineering. Imaging and other virtual design and construction tools can be used to identify weaknesses that trigger geohazards and can, in combination with numerical simulations, guide decision making. In spatially distributed problems, 3D visualization and LiDAR-type of technologies are essential in providing geotechnical engineers a deeper understanding of precarious soil zones and support finding appropriate solutions. This paper will present the value of using virtual design and construction technologies though the case study of the Iztapalapa suburb of Mexico, about 20 km southeast of Mexico City. Iztapalapa was developed within irregular topography and has a long history of severe soil subsidence. Following the 2017 Puebla-Morelos earthquake, the town experienced large settlements resulting in extensive damage to the already frail buildings and unregulated infrastructure. The soil subsidence was visualized by mapping available historic and geotechnical data. The visualization helped to identify areas where additional investigations were needed. Additionally, this paper presents a case study of a series of landslides from the 2016 Mw7.8 Muisne Ecuador Earthquake, which demonstrates the advantages of using novel technologies to collect data and create cloud datasets from drones and digital photos to understand and evaluate geo-vulnerabilities in anticipation of an extreme event and during rapid reconnaissance to plan for long-term instrumentation, which can enhance geo-disaster prevention and overall community resilience. INTRODUCTION Iztapalapa is a southeastern borough of Mexico City (CDMX) located within the Mexico Basin (Figure 1). This borough is a densely populated area of CDMX with a total of 1.8 million inhabitants, and has a third of its population living in poverty (Gonzalez-Hernandez et al., 2015) with limited to no access to clean drinking water. Iztapalapa also suffers from high rates of crime, drug trafficking, sex trade and illegal buildings. As the population continues to grow, the already non-regulated and fatigued infrastructure is unable to meet the community needs, especially during and after natural hazard occurrences. The region of CDMX is one of the world’s most seismically active regions that is also exposed to other geo-hazards such as floods, volcanic eruptions, and continuous settlement due to water pumping that has reached 11 meters over the past 100 years (Nikolaou et al, 2019). While the soil subsidence alone has caused significant infrastructure damage in Iztapalapa and throughout the rest of the city, recent earthquakes have also contributed to those damages.

Jan 1, 2019

By Kalyani Devabhaktuni, Mike Minton, Mark T. Howe, Yan Zhang

During the procurement phase of a Design-Build (DB) project, design-build contractors must often commit to a fixed price based on limited or incomplete geotechnical information. This lack of information can result in an inaccurate assessment and allocation of project risk to either the contracting authority or the DB contractor. This paper presents a case study of an elevated water tank supported by mixed ground improvement techniques, including Vibro-Compaction (VC), Aggregate Piers (AP) and Compaction Grouting (CG) in East St. Louis, Illinois. An adaptive design and contracting approach provided the best value solution for a complicated set of geotechnical problems, including static bearing capacity and settlement concerns as well as liquefaction induced settlement. Close cooperation between the owner, the tank contractor, the geotechnical engineer and the ground improvement contractor was essential to produce an effective solution. Ground Improvement techniques resolved the geotechnical challenges at the site through adaptive design methods, utilizing progressive rounds of verification and real time data acquisition to achieve performance objectives. This paper details the evaluation of geotechnical criteria, the selection of ground improvement techniques, the adaptive design and implementation of ground improvements, as well as contracting methodologies used to ensure that the best value was provided. PROJECT INFORMATION In November, 2016, CB&I Storage Tank Solutions (McDermott) submitted a design/build proposal for an elevated water tank for Illinois American Water Company (IAW) in East St. Louis, Illinois. The purpose of this tank was to have backup water capacity for power generation. In the RFP, IAW requested two alternate styles of tank: Option 1, a 1250 Million Gallon (MG) Composite Elevated Tank or Option 2, a 1250 MG Waterspheroid tank. Option 1 consisted of a steel tank supported on a concrete tower. Option 2 consisted of a steel tank supported on a steel shaft. The height (determined by IAW) was 140 feet to the top capacity line measured from top of floor slab.

Jan 1, 2019

This Section describes four alternative methods for load testing of drilled shafts: high strain dynamic test (HSDT), rapid load test, static load test, and bottom load test. Until recently, static load tests were the only method available for verifying the capacity of a drilled shaft. However, because many drilled shafts carry very high design loads, the static load test was prohibitively expensive. The alternative methods, HSDT, rapid load testing, and bottom load testing are gaining acceptance because of their lower cost and faster implementation. However, these different methods do not necessarily yield the same results. This section describes the load testing methods and the differences that may occur when interpreting the test results.

Jan 1, 2004