Search Documents

By R. A. Triglavcanin

Delivering dilution water and mixing this water with incoming feed slurry, addition of flocculant, maximising flocculant-slurry interaction to build aggregate size, unabsorbed flocculant percentage, volume average of solids volume fraction, momentum dissipation ratio, dilution recycle ratio, volume average shear, maximum shear rate at exit, aggregate size on exit, uniform discharge profile and more ? all of these need to occur in the right order and in the right proportions within the thickener feedwell, the secret to thickener performance.

May 1, 2009

By C. -M. Katsari, G. N. Anastassakis

"Copper is considered one of the most important industrial metals because of its properties (conductivity, malleability) and variety of uses. Approximately 70% of the global copper is used for various electrical applications, with a significant part of copper originating from recycling, since copper can be recycled and re-used countless times, without any loss of performance and difference in the quality of recycled copper in comparison to that from ore. Copper recycling significantly contributes to natural resources conservation, waste minimization, energy saving, and overall cost reduction. Approximately, 35% of the globally produced copper originates from recycled copper.The objective of the current work is to investigate the recovery of copper from electric wire scraps using wet shaking table as an alternative to air separation methods that prevail over the wet ones in recycling processes. The tests were carried out using feed of correspondingly high- and low-grade in copper. In the first case, the wire scraps had been subjected to shredding only, prior to tabling separation; in the later, the low-content tailing of prior air separation was used as feed ?n table separation.In regard to testing, the following factors were examined: table tilt, water flow-rate, and reciprocating speed. The results of the tests clearly denote that copper wire separation from plastic polymer is feasible, as in most cases, table separation resulted in heavy products of high purity in copper and high recovery, and tailings of very low copper grade. The results of the current work clearly denote that wet tabling can be applied efficiently for the separation of recycled copper wire from plastic, as an alternative to air separation methods, as well as for the recovery of copper from the low-grade tailings derived from air separation methods."

Jan 1, 2016

"Cambior currently has nearly 80 exploration properties, acting as operator on about 60 of these. The company's exploration budget has increased to over $11,100,000 for 1990. On-going efforts recently yielded a new gold discovery on the Douay- Vezza property, a joint venture project with Inco and Vior. Cambior continues to seek out new opportunities, recently acquiring an option agreement on the Sleeping Giant project in Quebec and four new exploration agreements in the United States, through its Reno office. Other nearly-concluded joint venture agreements have also given the company entries into Indonesia and Guyana.SummaryWhen it acquired SOQUEM's assets on August I, 1986, Cambior also acquired interests in 45 exploration projects. The subsequent mergers with Aiguebelle Resources and Sullivan Mines in 1987 brought the total number of exploration projects to 83, most of which are concentrated in northwestern Quebec. Cambior's strategy emphasizes gold exploration, and exploration activities were, therefore, initially limited to the Val d'Or and Rouyn-Noranda mining camps, where Cambior has a large portfolio of properties. Approximately $25.8 million has been spent on surface exploration in this area since the formation of the company, resulting in the discovery of the Mouska deposit and four sub-economic zones on the Porcupine, Forbex, Bloc Sud and Flavrian project s. In 1988, Cambior became involved in projects in the United States to which the company expects to allocate about 38070 of its 1989 exploration budget."

Jan 1, 1990

By Robert D. Brown, Robert B. Parsons

"Careful tax planning and proper attention to the regulations can result in an optimum deduction ""of the 25% federal resource allowance. Introduced in the Income Tax Act in1976, in part to compensate for the disallowance of provincial mining taxes and royalties. the 25% ""resource allowance"" is a permitted deduction in computing taxable income from mining and petroleum. However, the rules relating to the deduction are complex, and the importance of the deduction which can readily exceed 25% of net income- is frequently underestimated. This month, Tax Notes discusses the basic rules of calculating the resource allowance, and suggests some tax planning aspects which may warrant consideration.May 6, 1974 - "" .. . our provinces have adjusted royalties, mining taxes and other arrangements to derive what they perceive to be a fair share for the benefit of their people. However, a provincial resource is also a national resource... I am proposing that revenues derived by provincial governments in respect of production from a… mineral resource should no longer be.\ deductible in computing the income of the operator. .. I am proposing that. .. there be an extra abatement from federal income tax in respect of taxable production income.. .fifteen points in the case of mineral profits. .. "" - The Honourable John N. Turner, Minister of Finance. June 23, 1975-"" '"" to meet, at least in part, the request for some form of deductibility in the tax system for provincial resource levies... to offer more incentive to those who explore and develop in Canada. .. I am now proposing, the extra fifteen point abatement of federal taxes would be withdrawn... at the same time, I am introducing a new resource allowance, which would be an extra deduction from income equal to 250/0 of production income.. ."" - The Honourable John N. Turner, Minister of Finance."

Jan 1, 1980

By T. R. Chari

The safe-level dilution of low-level radioactive wastes in large volumes of selected granular material is proposed as an alternative method of permanent waste disposal to current Canadian practice of concentration and encapsulation. Accepting the fact that a "background level" of radioactivity exists throughout the world, the authors feel that the concept of controlled dilution of radioactive wastes to a level in keeping with "background" is a plausible alternative to current thinking on the subject and is worthy of equal consideration.

Jan 1, 1979

By Marty Hudyma

Mining-induced seismicity and rockbursting is one of the primary risks in deep mines. Seismic data management software has been created to facilitate analysis of mining-induced seismicity. The Mine Seismicity Risk Analysis Program (MS-RAP) is a purpose built database with mine seismicity analysis tools. One of the primary features of MS-RAP is the creation of seismic hazard maps in quasi-real time. The seismic hazard maps identify areas that are more prone to large seismic events and rockbursts, allowing risk management measures to be focused on the areas of greatest risk. These maps allow mining engineers to be more proactive about identifying and managing seismic related geomechanics risks in mines.

Oct 1, 2009

By Y. Miyabayashi, K. Nishikawa, H. Nagai

JX Nippon Mining & Metals Group recovers valuable metals from end-of-life electronic products in an economical and environmentally-benign way, based on technologies that have been acquired in mining, smelting, and refining operations over time. End-of-life electronic products contain halogens and hydrocarbons. When such materials are treated in the copper smelting process, corrosion of equipment and discoloration of sulfuric acid occur. As a countermeasure to these problems, we have developed pretreatment processes that include an incinerator, exhaust gas washing towers, and a defluorination facility. By implementing these improvements, we have been able to treat a large volume of end-of-life electronic products efficiently in the copper smelting process.

Jan 1, 2014

By D. E. M. Plaumann

"The wet grinding of asbestos has attracted the attention of engineers for many years as a means of improving fibre liberation from the ore. Today, added impetus for wet grinding has resulted from a need to minimize worker exposure to asbestos dust in conventional dry mills using air, as well as a need to provide a cleaner, technically superior fibre for use by product manufacturers. However, high viscosities of asbestos slurries create transport and grinding difficulties which have been a factor impeding use of a wet grinding process.Laboratory evaluation of reagents to reduce viscosities of asbestos slurries found that one reagent, XFS-4272.00, reduced the viscosity of a 35% (by weight) slurry by 75%. The impact of XFS-4272.00 on actual grinding parameters were evaluated using a pilot plant rod mill. Slurries containing 78% solids and XFS-4272.00 were successfully milled and asbestos fibres from that milling compared favourably in liberation and relative surface area to asbestos fibres obtained from milling a 4% slurry without additives. IntroductionAlthough the use of asbestos has been declining over the last few years, the large deposits of chrysotile in eastern Canada (Quebec in particular) remain very important. Asbestos production in Canada stands ninth in volume for mineral production with over 740 000 tonnes produced in 1985. Of this quantity, 722000 tonnes were exported with a value of $446 million. Canada is second in world production of asbestos behind the U.S.S.R. The milling of asbestos ore has been done primarily by a series of steps involving crushing, dry-grinding and aspiration using large quantities of air to release the fibres. Contrast this process to those practiced in the purification of virtually every other mineral. Ores other than asbestos are crushed and milled using an aqueous slurry in rod, ball or pebble mills. The finely ground mineral, still as a slurry, undergoes beneficiation by froth flotation, heavy media separation, hydrocyclones or any of the other aqueous techniques currently employed in mineral processing.One of the driving forces behind the use of air instead of water as a means of separating asbestos is the nature of the aqueous asbestos slurry. While most slurries of minerals contain as much as 80070 solids and can still be pumped and transported, asbestos slurries become highly viscous with as little as 10070 solids. These high viscosities reduce the pumpability of the slurry and create severe handling problems. Mills become prohibitively large and uneconomical due to having to handle slurries containing only 10% rock and 90% water.Health-related issues have affected the use of asbestos in many countries. In Canada, the asbestos-producing provinces have introduced stricter occupational legislation to improve safety in the workplace. This primarily means strict control minimizing release of air-borne asbestos fibres . Quebec and Ontario have set limitations of airborne asbestos at 2 (2) and 1(3) fibre per cubic centimetre of air. With present milling technology, maintaining these low levels in the workplace requires constant vigilance."

Jan 1, 1988

By S. Gößling-Reisemann

Most copper ores contain valuable co-products such as molybdenum, gold, silver, nickel, etc. Sulphuric acid and steam are valuable by-products, which are generated dur¬ing copper production. The environmental impacts from mining and refining therefore need to be shared between these by-products and co-products, an issue in Life Cycle As¬sessment (LCA) referred to as allocation. There are different, recognised methodologies for doing so: burdens can be allocated based on the market values of these commodities, they can be allocated by mass, volume, molar amount, functionality, or other physical, technical or economic factors. All of these methodologies have their respective merits and restrictions, and the choice is usually case specific. Nevertheless, the choice between alternative methodologies can have dramatic effects on the LCA results. Recycling in LCA has to be handled in a similar way, as it essentially constitutes a special case of co¬production. The existing standards (ISO 14040 ff.) allow different methods for imple¬menting recycling and allocation into metal LCAs (open loop, closed loop, value cor-rected substitution, etc.), which are still a subject of discussion in the scientific community. However, the methodology used can significantly influence the ecological profile of copper and copper products. We will present an overview of the different methodologies available for including recycling and allocation and give an analysis of how the meth¬odological choice affects the final LCA results. This work will be followed up by quantitative case studies.

Jan 1, 2007

By Frank Martonhegyi

"The objective of this paper is to review the coal basins in the Canadian part of the Western Cordillera to aid their understanding, and to aid in finding and proving places of economic coal mining potential. Coal occurs in eugeosynclinal basins in the Western Cordillera which evolved through three stages: -from systems of volcanic arcs in the Late Jurassic to mid-Cretaceous; -through an intermediate stage with deposition in increasingly restricted successor basins in Jurassic to Early Tertiary; -to a continental stage by the Eocene. Minor coal seams occur usually in late volcanic arc stage sediments bur they can be locally thick as they are on Queen Charlotte Islands. Successor basins usually show a marine-paralic-limnic evolurion. Signijicanr coal deposits occur in the tarter two sequences in the Whirehorse (Tantalus) and Bowser (SkeenaSusrur) basins. Currenr activities are intensive in the more accessible Bowser Basin, for example at Telkwa, Susrut River and on the Groundhog coal field. On Vancouver Island major coal seams occur in cyclic sediments, but the more accessible deposits are mined our. Exploration renewed recently in the less accessible northern part of the Island, for example Quinsam, for surface mineable coal. The Western Cordillera is a mosaic of allochtonous tectonic blocks. They originated from the south and were displaced northward by several hundred kilometres. Many Tertiary coal basins are related to strikeslip transcurrent faults along which the later part of displacement took place, for example the Dawson coal area in the Tintina Trench. Tensional and dipslip normal faulting also created or enhanced sites for thick peat accumulation. For example at Hat Creek 280 m of coal occur in a 550 m section. Secondary structures are often better exploration targets than the main fault zones. Pluvial and alluvial fan environments away from the main drainage are usually the favourable sites for thicker and cleaner coal deposition."

Jan 1, 1985

By J. Nsasi Bakambu

This paper describes an autonomous platform for exploration and navigation within networks of tunnels, as those typically found in underground mines and caves. In the exploration mode, a remotely located supervisor instructs the platform to move through successive sections of the network, gathering range data that is, then, concatenated into 2D/3D survey maps of the environment. In the navigation mode, the supervisor specifies high-level missions on the previously acquired survey maps. A motion planner, then, translates each mission into a set of consecutive navigation actions, separated by natural landmarks. Mission execution consists of detecting landmarks, self-localizing and performing the planned navigation actions.

May 1, 2003

By R. M. T. Raja Ismail

Shipping and stevedoring industry is going to witness a massive increase in the amount of containers to be handled while land constraints become more critical. Offshore transfer operations hence offer a preferable solution to deal with the surge in cargos rather than to expand the port outwards. Recently, there has been increasing research interests on offshore crane automation. Suspended cargos in a ship-mounted crane system are caused to swing due to the vibratory motion of the ship induced by ocean waves, which can lead to collision between cargos and deck. Therefore, it is vital for offshore crane systems to satisfy rigorous requirements in terms of safety and efficiency. This paper presents the modelling and control development for offshore boom crane systems. A second-order sliding mode control law is proposed for trajectory tracking and sway suppression control, making use of its capability of actuator chattering alleviation while achieving high tracking performance and preserving strong robustness. The asymptotic stability of the closed-loop system is guaranteed in the Lyapunov sense. Simulation results indicate that the proposed controller can significantly reduce the effect of disturbances coming from gusty waves and other dynamic loadings.

Aug 1, 2013

By Bordeaux Sciences Agro-INRA UMR 1065 SAVE, S. Piutti, E. Benizri, S. Lopez

Ultramafic soils display high concentrations of nickel (Ni) and a number of nutrient deficiencies (e.g. N, K, P). Ni-hyperaccumulator plants have evolved on such environments, developed specific metal homeostasis showing concentrations of Ni sometimes above 1% in their aerial biomass (Baker & Brooks 1989). Alyssum murale, a Ni-hyperaccumulator, is commonly found around the Mediterranean but can grow on non-ultramafic soils as well, with an altitudinal extension ranging from sea level to 2000 m.a.s.l. Rhizosphere bacterial communities associated with Ni-hyperaccumulator plants can differ from those of non-accumulating plants growing at the same site. Among edaphic factors that could influence the phylogenetic structure of the bacterial communities, altitude and metal-bioavailability and in particular nickel could be significant. However, most studies have focused on analyzing soils with techniques that provide little detail about the phylogenetic structure of these bacterial communities present in ultramafic soils. The objectives of this study were to understand the specific changes in the structure of A. murale rhizosphere bacterial community that occur across two gradients: 1°) elevation and 2°) Ni geochemistry, using pyrosequencing technique (454-pyrosequencing of 16S rRNA gene). It was found that the higher the soil chemically-available Ni contents, the higher the relative abundance of Proteobacteria and Actinobacteria. On the contrary, the abundance of TM7 decreased with increasing levels of available Ni. Moreover, Chloroflexi was present with 53 to 77% of relative abundance. These results demonstrate that soil chemically-available Ni drives the bacterial community diversity in the rhizosphere of Alyssum murale regardless the elevation gradient and other different soil physicochemical parameters. These results should now be confirmed in different ultramafic edaphic environments worldwide (e.g. ultramafic lateritic covers) and in the rhizosphere of different hyperaccumulator taxa.

Jan 1, 2016

By Samuel Frimpong

Green house gases have become a major concern within the international community over the last two decades due to their potential link to global warming. Carbon dioxide (CO2) is the principal greenhouse gas. In the Kyoto Agreement, Canada has committed to reduce emissions by 6 % below 1990 levels by 2012. This presents a serious economic challenge to Canada and Alberta. Over the next decade, oil sands production expansion, population and industry growth and energy demand will increase CO2 emissions. Current and future CO2 emissions and their economic implications in Alberta will be critical in formulating a comprehensive and balanced policy for dealing with concerns in this area. Disposal of carbon dioxide (CO2) in land aquifers is a potentially viable option for Alberta in dealing with long-term CO2 emissions. Studies have confirmed the existence of appropriate aquifers in the Alberta Basin for CO2 storage over a long geological period. Carbon dioxide is an ideal candidate for aquifer disposal because of its high density and solubility in water at relatively high pressures. In this study, the authors develop a computer simulation model of a scaled aquifer disposal system. The scaled model consists of an injector well, aquifer environment with dominant Ca++ and Mg++ cations. Liquefied CO2 is injected at an appropriate pressure and concentration through an injector well model. The injected CO2 migrates from the point of contact between the injector well and the aquifer domain to the main regime of the latter. The rate of migration is a function of porosity, permeability, cations, aquifer fluid flow regime and CO2 injected pressure. These models are validated using flue gas data from the 546 MW Wabamum Power Plant in Alberta. The total energy requirements for aquifer CO2 disposal system are distributed between a minimum of 105 MW and a maximum of 172 MW, with a mean of 132 MW and a coefficient of variation of 10%. The results show that there is significant variability in all the energy requirements for the CO2 disposal system. The total energy requirements for the disposal system as a fraction of the total power generated by the Wabamum plant of 546 MW could be between 0.19 and 0.32. This is a very significant energy requirement and thorough analysis must be carried out to reduce this variability and energy requirements.

May 1, 2001

By Stephen Hardcastle

Personnel Heat Exposure Issues In Canada?s Deep Mechanized Mines ?Project developed in 2004 ?Base/precious metal industry identified heat stress/management as a major challenge affecting productivity and operating costs ?Project started in 2005 ?Current research nearing completion ?Guidelines, further data analysis and ?Communicating the Science? will continue into 2011 Managing Heat Exposure Control?. The cost implications ?Controlling the environment ?Ventilation already a major expenses/energy user ?Large Canadian mines are currently delivering massive volumes of air 15-20 tons of air/ton ore ?Large investments in ventilation upgrades, mechanical cooling

May 1, 2010

By I. P. Swainson, A. Ilbagi, H. Henein

Powders of Al-50wt%Ni, Al-40wt%Ni and Al-36wt%Ni were produced using the Impulse Atomization technique, a rapid solidification technique. The molten droplets were cooled in-flight by the stagnant helium or nitrogen in the atomizing chamber. The resulting powders were sieved into different size ranges. X-Ray diffraction and neutron diffraction were used in order to quantify the phase fractions in the samples. The computer software GSAS was used to calculate the weight fraction of the existing phases, namely Al3Ni2, Al3Ni and Al, by profile refinement method. The effect of processing parameters, alloy composition and particle size will be discussed in this paper. In brief, no AlNi was found in any of the samples analyzed. Higher cooling rates resulted in the reduction of the ratio of Al3Ni/Al3Ni2. Also, at high cooling rates, Scheil closely predicted the ratio of Al3Ni/Al3Ni2. Some metastable phases were found in Al- 36wt%Ni.

Jan 1, 2010

By Marty Hudyma

Mining-induced seismicity and rockbursting is one of the primary risks in deep mines. Seismic data management software has been created to facilitate analysis of mining-induced seismicity. The Mine Seismicity Risk Analysis Program (MS-RAP) is a purpose built database with mine seismicity analysis tools. One of the primary features of MS-RAP is the creation of seismic hazard maps in quasi-real time. The seismic hazard maps identify areas that are more prone to large seismic events and rockbursts, allowing risk management measures to be focused on the areas of greatest risk. These maps allow mining engineers to be more proactive about identifying and managing seismic related geomechanics risks in mines.

Oct 1, 2009

Flotation of a mineral bearing particle is the result of successful completion of a chain of events, such as, producing particles with sufficient exposure of the valuable mineral on the surface, reagent adsorption, suspension of the particle in the pulp, collision of particle with air bubbles and subsequent attachment, ascending to the froth column and transport to the concentrate stream, among others. These sub-processes in turn are affected by the feed properties such as size and density, and process variables such as size of air bubbles, degree of turbulence in the cell, particle/particle interactions etc.. Thus, inefficiencies occurring in any one or more of the above processes will result in inefficient flotation performance. In spite of its dependency on a wide variety of sub-processes, flotation performance is commonly modelled based on first order kinetics using two or three parameter models. As the model parameters may be affected by several of the sub-processes mentioned above, interpretation of their variations and identifying the specific causes is extremely difficult. Of the many factors that influence the flotation performance, liberation information of the particles such as the grade distribution and surface exposure are considered vitally important. In this paper, it has been demonstrated a) how a predictive liberation model may be derived and used in quantifying the liberation information of the particles produced at various grind sizes and b) how the flotation process may be modelled by explicitly incorporating the liberation information, thereby improving the accuracy of the model. Comparisons of the observed data with the proposed model and those of published liberation/flotation models have also been made.

Jan 1, 2016

By J. R. Shore, F. G. M. Gillett, E. J. Zickar

"The addition of fines to rod mill feed has been employed at Inco Metals' Frood-Stobie Mill since 1973. The fines, which act as a ""lubricant"", causes an increase in the pulp fluidity and assists the flow of feed through the rod mill. Fines addition was one of the main factors which led to improved rod mill performance and the elimination of rod mill tangles.This paper outlines the testwork performed in evaluating the addition of fines, and summarizes the beneficial effects on rod mill grinding efficiency, throughput rates, power consumption and noise level. INTRODUCTIONFrood-Stobie Mill is situated within the Frood-Stobie mining complex, on the southern rim of the Sudbury Basin. The Mill commenced operations in November, 1967, and has since processed in excess of sixty-five million tons of ore. Minus 8-inch ore is delivered to the Mill's coarse ore bin by two surface conveyor belts from the Frood and Stobie Mines, while Little Stobie ore is transferred by underground conveyor and hoisted directly into the coarse ore bin a long with additional Stobie Mine ore."

Jan 1, 1981

By F. S. Hoseinian, M. Irannajad, M. Safari

In this study, the effect of chemical interactions of materials used in ion flotation on the removal of Ni(II) ions from low concentration synthetic wastewater was studied. Sodium dodecyl sulfate (SDS) and ethylhexadecyldimethylammonium bromide (EHDABr) as collectors and methyl isobutyl carbonyl (MIBC) and Dowfroth250 as frothers were used. To investigate the effective parameters and interactions of them, 16 experiments including 6 level variables were performed by supporting DX7 software and on the bases of 2-level factorial method. In the first step, the tests were conducted in a Hallimond tube. The result showed that collector of SDS and frother of Dowfroth 250 had appropriate interaction with each other at pH = 3. In the second step, optimal results from the first step were evaluated in a mechanical flotation cell. The removal of Ni(II) ions increased by increasing the time of flotation and they have a direct relation with the water removal. The kinetics study shows that the order and the rate of removal of the reaction do not follow any of the zero-order, first-order and second-order equations. The flotation rate curve on the removal of Ni(II) ions will divide the separation process to two stages, a fast flotation rate at the first stage and a slow flotation rate at the second stage. Ni(II) ions removal was obtained 88% at the best condition.This study showed that the use of ion flotation was a very effective method for Ni(II) ion removal from industrial wastewaters.

Jan 1, 2016