Search Documents

By M. H. Moys, J. A. Engelbrecht

"Large-diameter flotation columns are subject to severe axial mixing which has reduced column recovery and has generally limited it to cleaner applications. It has been assumed that columns with diameter greater than 1 m should be baffled to reduce axial mixing, but little work has been reported quantifying the effectiveness of baffling. Tests were done on a 0.2 m by 2 m column fitted with baffles of different geometry. It was generally found that the inclusion of baffles in the column worsened rather than improved mixing conditions in the column. This is explained in terms of a model for the effect of poor gas distribution on the behaviour of the column; this showed that under typical conditions a 16% excess of gas flux in the one compartment of a two-compartment column could result in one of the compartments being ""dead"" (i.e. with no net flow of slurry through it), resulting in a substantial loss of performance. The quality of mixing in the laboratory column was only reliably improved when the baffle was raised so that its top was positioned above the froth-slurry interface level. It should be possible to increase column recovery substantially with this configuration. The improved residence time distribution also means that columns can be used more effectively in roughing and scavenging applications. IntroductionFlotation columns have generally been used in cleaner applications, starting with their dramatic success at Mines Gaspe(1). Their lack of applications as roughers and scavengers is probably due to their poor residence time distribution (RID) when compared to the conventional cells they would replace. Espinosa-Gomez et al,(2) recently used them in rougher applications but installed three columns in series, presumably to cope with this disadvantage.Dobby and Finch in their seminal papersl(3,4) on the scale-up of flotation columns were the first to quantify the impact of axial mixing on the performance of industrial flotation columns. Laplante et al.(5) collected further data from the literature for column diameter D, ranging between 5 cm and 183 cm, gas superficial velocity Jg ranging between 0.7 cm/s and 2.8 cm/s and per cent solids in the feed S ranging between 3% and 52%. These data were analyzed with reference to the axial mixing model using the boundary conditions for closed vessels (the latter are more appropriate for flotation columns but the model is more difficult to use because analytical solutions for the RID are not available). The data were correlated by:"

Jan 1, 1993

By P. C. Holloway, M. J. Collins, K. R. Buban

Historically, there has been little incentive to process copper-arsenic concentrates by leaching, rather than via established smelting operations. However, with ever tightening environmental emission standards and more arseniferous concentrates being produced, increasingly sophisticated and upgraded off- gas handling facilities are required in smelting operations, generating greater quantities of challenging metallurgical dust. In this context, oxidative pressure leaching offers distinct advantages. The current state of pressure leach technology delivers high extractions from copper concentrates, while producing an environmentally stable process residue, without atmospheric emissions of sulphur dioxide or arsenic. However, as was shown in an earlier study, copper extractions and environmental leach residue stability are impacted negatively by arsenic levels above 2.5 to 3.0 wt%. In further studies on pressure leaching of copper concentrates, Sherritt has developed process conditions that allow even highly arseniferous (> 7 wt% As) feed materials to be converted into environmentally stable residues, with excellent copper extractions. At the same time, pressure leach residues can be generated that are amenable to silver recovery via direct cyanidation, without pre-treatment by lime boiling or hot curing. The results of pilot plant test work are discussed. INTRODUCTION As the production of copper has expanded over the years, resource exploitation has extended beyond relatively clean, high grade and easily accessible ores, and copper sulphide concentrates increasingly come with higher levels of contaminants, such as As, Hg, Sb and Bi, and lower copper and sulphide sulphur concentrations. However, as concerns on the impact of the emission of such contaminants into the natural environment have mounted, import/export restrictions have made the trading of copper concentrate more difficult, and, in particular, the export of concentrates with greater than 0.5 wt% As; under ever tightening environmental emission standards, these lower quality concentrates can be a significant strain on the off-gas handling facilities in smelting operations. The processing of arsenic bearing copper concentrates is, therefore, an increasing challenge as copper producers seek to exploit more complex mineralization and to extend the life of their operations. In this environment, processing arsenical copper concentrates with high temperature pressure leaching (>200°C) must be considered as an alternative to pyrometallurgical processing. Leaching kinetics for copper minerals at these temperatures are rapid and acid is generated for potential use in heap leach operations. Pressure leaching of copper concentrates eliminates gaseous emissions of arsenic and sulphur, while generating environmentally stable residues, as measured by the Toxicity Characteristic Leach Procedure (TCLP) (Kalanchey et al., 2007). Both medium and high temperature pressure leaching of copper concentrates have also proven themselves technically on an industrial scale (Marsden et al., 2004) with high copper recoveries.

Jan 1, 2019

By Li Qihou, Liu Zhihong, Liu Zhiyong, Yao Wei

Black copper sludge, which mainly contains copper, arsenic and a little antimony, bismuth, selenium, tellurium, is an important recyclable secondary resource. In this paper, selective removal of arsenic from black copper sludge by alkaline oxidative pressure leaching was studied. The influences of alkali concentration, leaching time, leaching temperature, oxygen pressure, liquid-solid ratio and other variables on the leaching rate of arsenic, copper and tellurium were investigated. The results were as follows: when the leaching process was conducted at initial alkali concentration of 1mol/L, liquid-solid ratio of 10, stirring rate of 500r/min, leaching temperature of 140°C for 5 h and oxygen pressure of 2.5MPa, the leaching rates of arsenic and tellurium were 85.43% and 59.7% respectively, and copper, antimony, bismuth were not leached. Hence, arsenic has been removed effectively from black copper sludge, while the valuable metals such as copper, antimony and bismuth remained in the residue that can be further recovered easily. INTRODUCTION Black copper sludge is a byproduct in the purification process of copper electrolyte. Arsenic, antimony and bismuth are major harmful impurities in copper electrolytic refining system. The accumulation of these impurities will cause adverse effects, such as the increase of electrolyte resistance and power consumption and deterioration of cathode copper quality (Wang, Liu, & Zhang, 2001). Hence, electrolyte purification is an essential part of the electrolysis process (Liang, Chen, & Guo, 2009). Electrolyte purification methods include electrowinning (Davenport, King, Schlesinger, & Biswas, 2002), solvent extraction (Navarro, Simpson, & Alguacil, 1999), ion exchange (Arroyo et al., 2017), coprecipitation (Wang et al., 2003, 2018; Xiao et al., 2007; Xiao, Cao, Mao, Shen, & Ren, 2014), activated carbon adsorption (Navarro & Alguacil, 2002), electrodialysis (Cifuentes et al., 2015), redox process (Zhou, Peng, Zheng, Ma, & Cui, 2011; Peng, Zheng, Zhou, & Chen, 2012; Zheng, Peng, Ke, & Chen, 2013), among which the electrowinning method is simple in operation and effective in impurities removal, making it the main process for current electrolyte purification. Some copper ions can react with harmful impurities to form complex black copper sludge by controlling the operation conditions of electrowinning process. Based on the estimated data provide by Davenport et al. (2002), an annual output of 400,000 tons cathode copper could produce 432-2168 tons of black copper sludge by electrowinning method. Black copper sludge contains 30~50% copper, 15~30% arsenic and a small amount of rare elements such as selenium and tellurium. Thus, recovery of valuable metals can bring huge economic interests. Moreover, arsenic in these sludges could cause significant environmental pollution. Therefore, effective removal of arsenic from these sludges is urgent and significant.

Jan 1, 2019

By Norman R. Ball

"Many people in the mining and metallurgical industries were brought up to embrace Henry Ford's pronouncement that ""History is bunk"" but it is not generally known that the same Henry Ford created and paid for one of the finest technological museums in the Western World. I am aware that many people feel that industry history is something you ask aging executives to do or that history is a clip-andpaste compendium of pictures re-discovered every 25 years or on the occasion of issuing a press release on plant expansion. Moreover, there are many who fear historians as somewhat deranged individuals interested only in corruption, injustice and sensational labour strife. Good history lies somewhere between the controlled P.R. handout and the hysterical attack. Writing good history is a difficult creative act based on the application of experience, insight, wide knowledge and careful reasoning to available evidence. To date, the Canadian mining and metallurgical industries have achieved a great deal but left too little evidence and it is this lack of evidence which must be corrected before it is too late. It is the purpose of this article to stimulate thoughts with regard to archives, one of the more important vehicles for the preservation of such evidence."

Jan 1, 1999

By J. L. Jambor, E. J. Reardon, E. C. Appleyard, J. A. Cherry

Since the 1957 initiation of deposition of mill tailings at the Heath Steele mine, New Brunswick, periodic detailed studies of the tailings geochemistry and mineralogy have been conducted, thereby providing a unique opportunity to examine the geochemical evolution of a sulfide rich mine>tailings impoundment. When deposited, the tailings contained about 85 wt% sulfide minerals, 1 wt% to 3 wt% carbonate minerals, and 12 wt% to 14 wt% alumino silicate minerals. Mineralogical examination of samples of the tailings from deep in the impoundment indicates that little oxidation occurred prior to tailings deposition. The mill process-water deposited with the tailings was neutral to slightly basic and contained low concentrations of Cu, Pb, Zn and As. Sampling of the tailings five years after deposition indicated that sulfide-oxidation reactions, occurring near the tailings surface, had decreased the tailings-water pH and increased the concentrations of Fe, S042-, Cu, Zn and Pb (up to 10 000 mglL, 25 000 mg/L, 2.5 mg/L, 200 mg/L, and 4.5 mg/L, respectively). In 1975, ten years after decommissioning, the tailings could be divided into three zones: an upper oxidation zone in which sulfide oxidation is actively occurring, a hardpan layer, 15 cm to 20 cm thick, composed of tailings cemented by secondary Fe minerals, and an underlying reduction zone in which the tailings are relatively tin oxidized (Boorman and Watson, 1976). Chemical analyses indicated the presence of low-pH waters containing very high concentrations of SOi-, Fe, and other metals (up to 63 600 mg/L SO42-, 28 600 mg/L Fe, 10 mg/L Pb, 600 mg/L Cu and 4000 mg/L Zn), suggesting that there was a period of intense sulfide oxidation between five and ten years after tailings deposition. More recent sampling, conducted some 20 years after the end of tailings deposition, indicates that relatively little change has occurred in the last ten years, thereby suggesting that the hardpan layer has provided an impediment to the downward movement of dissolved constituents. Analyses of the tailings solids show increased accumulations of many metals at or near the depth of the hardpan layer. Evaluations of the long-term evolution of the tailings can be enhanced by comparison of descriptions of the tailings with descriptions of the gossan that overlay the massivesulfide orebody prior to mining. At Heath Steele, this comparison suggests that many of the mechanisms controlling the distribution of metals in the tailings will probably persist over geologic time.

Jan 1, 1992

By Louise Corriveau

Exploration strategies have traditionally considered felsic gneiss complexes of the Canadian Shield sterile. This paradigm is challenged with the discovery of extensive granulite-facies Cu-Au, Fe oxides-bearing hydrothermal systems in the 1.4 Ga Bondy and 1.5 Ga La Romaine volcano-plutonic complexes of the Grenville Province. Early identification of magnetite-rich units in association with meta-exhalite and pelite-like units was key to targeting the search for mineralization, protolith information and indicators of pre-metamorphic hydrothermal activity during regional surveys of these frontier terrains. Textural evidences for a volcano-plutonic setting were found. There remained, however, numerous impediments to the recognition that the ubiquitous magnetite-laden units and associated aluminous gneiss were hydrothermal in origin. Many metamorphic reactions form magnetite at the amphibolite to granulite facies transition, and hydrothermally-leached rocks resemble metapelite or migmatitic restite, while carbonate alteration zones may look like marble or calc-silicate rock. Non-typical metamorphic mineral assemblages, modes and colours arise when hydrothermally-derived rock types are metamorphosed. These effective markers served as tools for reliable field identification of hydrothermally-altered rocks. In our case-studies, we traced pre-metamorphic hydrothermally-driven Fe-oxide precipitation in association with sericitization, albitization, pyrophyllite alteration, chloritization, and B enrichment by mapping unusually high contents of (1) magnetite or hematite, (2) biotite, (3) albite, (4) sillimanite, (5) orthopyroxene or phlogopite with cordierite, and (6) tourmaline or kornerupine. The unveiled garnetite, tourmalinite, and aluminous gneiss had assemblages that vary according to metamorphic grade and composition. To assess if high mode of Fe-Mg-Al phases resulted from partial melting (restitic residue) or metamorphism of hydrothermal rocks, we compared leucosome mineral assemblages, shape and amount with that expected of in situ partial melting reactions. In both areas there is no compelling evidence for these units to be restites. In contrast, the presence of lapilli in garnet-cordierite-sillimanite gneiss, though extremely rare, constitutes conclusive evidence for extreme pre-metamorphic high-sulphidation alteration of a volcanic protolith, while Fe-oxides or sillimanite-bearing nodules and veins record a less pervasive alteration. Geochemical research on element mobility and mass balance calculations further testified of an hydrothermal origin for these gneisses. The magnetite-rich units, together with calc-silicate rocks, garnetite, hornblendite, albitite among amphibolite, provided effective guides to sites of fluid discharge and led to the discovery of Cu and Cu-Au showings. With the presence of highsulphidation alteration, these features suggest early Cu-Au VHMS-type alteration halos within a predominantly felsic composite volcano-plutonic arc setting for both case-studies. Evidences for subsequent F-driven orthomagmatic fluid activity are also present.

May 1, 2003

Strips of AA6111 automotive alloy were cast on a horizontal single belt strip casting simulator, Pure copper and carbon steels substrates plasma sprayed with different coatings for improving the strip surface quality, were used as chill moulds, Experimental studies revealed that a graphite coating provided the greatest benefit in achieving good surface quality. The interfacial heat fluxes during solidification of AA6111 strip were calculated by the IHCP method (Inverse Heat Conduction Problem). Temperature variations and cooling rates within the strips were then calculated through numerical simulations based on the time-dependent heat fluxes obtained by IHCP, The effects of casting parameters, including casting temperature and strip thickness, on interfacial heat fluxes, cooling rates and microstructures, were investigated, Although the maximum interfacial heat fluxes on the chill copper substrate were much higher than the results obtained from the steel substrates, the solidification times of the melts were mainly determined by strip thickness. Very fine equi-axed grains were obtained for both 1.2mm and 2.5mm thick strips thanks to the rapid extraction of heat, and effective grain refinement.

Jan 1, 2005

By Greg Johnson

Maintenance needs information about assets to optimize availability and production needs information about performance and consumption to maximize output. In considering both these needs together as, ?Asset Optimization?, the information systems that support them are critical. The theory of Asset Optimization derives from the Lean Manufacturing concepts developed by Toyota, but some changes are required to apply this to mining operations. In particular, mining operations require automated systems due to their geographic spread and they need a strong emphasis on capturing under-performance losses as well as delays and stoppages in production. Leading metal miners and coal miners alike have applied these systems to good effect in the last 10 years. The concepts developed initially in minerals processing plants are now being applied to the mines themsleves as well as the mining logistics chain. Production increases of 5?10% are achievable with the right implementation and consideration of the some key lessons learnt in the last 10 years. Putting these lessons into action is one key step in the goal of optimizing asset performance and thus utilizing the resource at lowest cost.

Aug 1, 2013

By J. A. Finch

Solvent-coated air bubbles in the Air-Assisted Solvent Extraction (AASX) process achieve the dual role of high solvent specific surface area and ease of phase separation. The thickness of the solvent film is of fundamental interest but difficult to measure directly in the process itself. As an approach interferometry (in the UV-vis region) was used to measure the time dependent thickness of a film formed by blowing an air bubble in kerosene-based solvents. The film was stabilized by the presence of 1.5 ppm silicone oil, as employed in AASX. The film appears to comprise two layers; an outer "free" layer of almost constant thickness and an inner "bound" layer which decreased in thickness with time. The bound layer is considered relevant to AASX. For a 20 mm diameter bubble blown in LIX/kerosene solvent the initial thickness was ~ 3 um which decreased over 10 minutes to a final rupture thickness of 500 nm. The bound layer thickness and time to rupture decreased with decreasing bubble size. Correspondence to prior indirect estimates of solvent layer thickness is examined.

Jan 1, 2006

By S. J. Buckler

Many metallurgical processes use submerged gas injection to increase the contact area between gas and liquid phases in order to promote faster overall reaction rates. The work presented in this paper is part of an experimental investigation to measure the gas-liquid interfacial area available in bubble plumes within molten metal baths. Measurements of the nitrogen absorption rate during submerged injection into molten iron baths have been used to estimate the interfacial areas of the bubble plumes. A theoretical model was used to predict the superficial nitrogen transfer rate under mixed liquid phase mass transfer -interfacial reaction control. The interfacial area was calculated by dividing the overall nitrogen absorption rate by the superficial rate. Reasonable agreement was obtained between the interfacial areas measured in our laboratory with data from a comparable system reported in the literature. The experimental results were compared with the predictions of three theoretical models and one empirical correlation. The models of Turkdogan (3) and Zhao and Themelis (5) gave the best agreement with our data.

Jan 1, 2004

By Z. F. Lodhi, J. H. W. De Wit, H. A. Terry

Zinc and its alloys have been extensively used as replacements for Cadmium coatings in aeronautical and automobile industries. Zn alloys with low Co or Fe have been highly investigated but coatings with higher amount of Co are very difficult to achieve due to anomalism associated with these coatings. Anomalous Zn-Co-Fe alloy is a relatively recent addition to the family of Zn alloys. It is found that the addition of Fe in the electrolyte assist in overcoming the anomalism. In this research Zn-Co-Fe alloys especially with higher amount of Co (>15%) and Fe (~1%) are investigated, after overcoming the anomalism associated with its deposition, and the corrosion resistance is compared with pure Zn and Cd. It is found that an increase in Co to higher than 25 % accounts for a shift in the OCP to a level near Cd yet keeps it electronegative to steel. The coating shows superior corrosion resistance, in terms of its sacrificial and barrier properties in 3.5% NaC1 as compared to Zn and Cd.

Jan 1, 2006

By Martin Encinas, Jesús L. Valenzuela, Jose R. Parga, Salvador Aguayo, Roy G. Lewis

Continuous laboratory solvent extraction of gold from cyanide solutions using LIX?79 guanidine based extractant has been investigated. Different variables that affected the selectivity and extraction include aqueous pH, extractant concentration, and modifier concentration. The extraction isotherms of the aurocyanide complex with respect to the other cyano anions were compared, and the following order of selectivity Au > Ag > Zn > Cu > Fe was observed. According to the pH isotherms, aurocyanide can be extracted in an alkaline media, and a better separation with respect to the other cyanoanions was obtained in the pH range 10.5-11.2. From the McCabe Thiele diagrams, better recovery was predicted when using LIX?79 extractant and tridecanol modifier at 10 vol.%. Stripping of the gold from the loaded organic was carried out at pH > 12 using NaOH and NaCN solution. The continuous tests indicate that a two-stage extraction followed by a single stage strip is adequate to obtain an overall process efficiency of >90%. Better results were obtained using a copper wash stage before gold stripping.

Jan 1, 2014

By R. Bonnar, R. J. McH. Clark

"The Cheminis gold mineralization zone is approximately 6.5 km west of the Kerr Addison Mine along the Larder Lake Shear Zone, in the southern part of the Abitibi Greenstone Belt. The zone is very similar in appearance to the flow ore at the Kerr Addison Mine and occurs at the same stratigraphic position. Drilling has demonstrated that the gold mineralization at Cheminis persists to a depth of over 3000 ft .The mineralization is hosted by a pyritic, tuffaceous sediment which occurs within a sequence of volcanics and sediments which have been pervasively carbonatized. The gold is largely enclosed within pyrite grains and the amount of gold in the layers of pyrite increases in the layers closest to a graphitic f ault zone.It is suggested that the gold mineralization may be primarily related to the syngenetic sulphide concentrations formed during fumarolic activity on the seafloor along the Larder Lake Shear Zone. At a later stage a hydrothermal event associated with alkalic volcanism may have resulted in regional carbonatization and further concentration of the gold in the vicinity of fault zones."

Jan 1, 1987

By Edward Martinez

Laboratory studies had shown that the magnetite contained in serpentine asbestos ore was not uniformly distributed. Ore particles containing chrysotiye fiber responded to a magnetic f field; particles containing little or no chrysotile were essentially non-magnetic. Larger-scale tests, run with a magnetic pulley being fed various asbestos samples ranging in size from 1/4 inch to 5 inches, confirmed that magnetic separation could be used as a concentration step in an asbestos mill. Magnetic concentration was installed at the Black Lake and National mills of Lac d'Amiante du Quebec and has allowed the extraction of lower-grade ore, increasing the life of the mines. In addition, preconcentration early in the flowsheet increased the value of the feed to the fiber recovery section. An increase in fiber production was achieved, as well as a decrease in maintenance costs due to removal of flow-grade tailings early in the flowsheet. Magnetic concentration of a coarse tailings from the mill resulted in recovery of additional fiber previously discarded to tailings.

Jan 1, 1979

By Rodney Trevor Jones, Arthur Robert Barnes

Anglovaal Minerals acquired the Nkana slag dump from Zambia Consolidated Copper mines (ZCCM) in 1998 and embarked on an ambitious project to pioneer the recovery of cobalt from slag using DC smelting technology. Anglovaal Research Laboratories performed initial pioneering smelting tests in a 250 kW DC furnace over a 3-year period before engaging Mintek for three piloting campaigns at the 1.5 MW level. Mintek had previously developed a reductive smelting process, patented in 1995, using a DC arc furnace for the recovery of cobalt from slags. The results of the pilot-plant test campaigns were used as the basis for engineering the commercial 40 MW operation installed at Chambishi Metals plc in Zambia in 2001. This paper traces the development of understanding of the metallurgical fundamentals ultimately used to predict furnace performance, reviews some of the extreme technical challenges faced, how solutions were identified and highlights some of the critical issues identified during piloting and how these impacted both positively and negatively on the final commercial operation.

Jan 1, 2011

By A. Uribe-Salas, J. A. Finch, B. J. Huls

Froth depth or interface level is an important control variable in column flotation which can influence both grade and recovery. A common method of locating the level is based on sensing the hydrostatic pressure at one or more points along the column. The level indicated can be in considerable error, largely because of variations in froth and collection zone bulk densities. A portable conductivity probe has been developed to detect the position of the interface from conductance measurements across the interface. The location of the interface corresponds to the position where a large change in conductance is observed, which is primarily a consequence of the difference in gas holdup between the collection and froth zone. This probe detects the position of the interface to an accuracy of ± 5 cm. The probe can be used while the column is in operation, which allows for on-line recalibration of the level detection system. Results obtained in its application in a pilot-scale column (0.91 m in diameter) are described.

Jan 1, 1990

By H. Somekawa

The fracture toughness and deformation structures an AZ31 magnesium alloy processed by equal-channel-angular extrusion (ECAE) were investigated. The average grain sizes of as-ECAE and annealed-ECAE alloys were 4.0 and 16.3 µm, respectively. The plane-strain fracture toughness, Kip, in as-ECAE and annealed-ECAE were estimated to be 27.3 and 23.5 MPam1/2, respectively, by stretched zone analysis. The fracture toughness indicated higher value with grain refinement. From optical microstructural observations in samples after fracture toughness tests, although deformation twins were observed in annealed-ECAE, no deformation twins were observed in as-ECAE. From TEM observations, the dislocations on basal and non-basal planes were activated in as-ECAE. With grain refinement, the activations of dislocations on both basal and non-basal planes were possibly related to the reduction in formation of deformation twins in as-ECAE. In addition, in comparison with direct extruded process, ECAE process was more effective method to improve the fracture toughness in magnesium alloys.

Jan 1, 2006

By G. Gagnon

"HistoryMining of the Schefferville iron deposits began in 1954 on completion of the 357 mile railway linking the mines and the St-Lawrence river port of Sept-Iles. Apart from crushing, no treatment of these ores was required before smelting. In the late 1950's, testwork began at schefferville to develop a process for upgrading the extensive lower grade deposits containing 51% iron with 15% silica (natural analysis). Engineering for a six million ton per year beneficiation plant using cationic silica flotation and the A-C grate kiln Began in 1970 and the first pellets were produced in mid-1973.Production requirements and operating difficulties have restricted capacity to approximately 85% of design but on going improvements are being made continuously to attain design capacity.GeologyThe sedimentary ore bodies of the labrador trough occur in a belt 5 to 10 miles wide and 60 miles long and contain 51 individual deposits varying in size from 1 and 60 million tons. The ores are classified into three main color groups."

Jan 1, 1981

By J. W. McCammon

CRANGES in construction ideas and the continually rising costs of labour and conventional building materials, particularly since World War II, have prompted widespread investigations into the development and adaptation of new materials to meet the new requirements and to help reduce costs. Lightweight aggregates have been prominent in these investigations. The lightweight aggregates most commonly used today are foamed slag, cinders, pumice, diatomite, exfoliated vermiculite, expanded perlite, and bloated clay or shah. Lightweight aggregates contribute to the building industry in several ways: ( 1) in large structures the reduction in deadweight effected by the use of lightweight materials reduces the amount of reinforcing and structural steel necessary to support the structure; ( 2) the decrease in weight of lightweight blocks makes handling easier and faster; (3) pre-fabricated floor and roof slabs and tilt-up walls of lightweight concrete have become feasible and popular; ( 4) lightweight aggregate concrete has good nailability and is easily channelled; (5) concrete and plaster made with lightweight aggregate have good heat and sound insulation properties.

Jan 1, 1957

By R. Therrien, L. Gosselin, J. Raymond

ABSTRACT: The ground-source heat pump is a low-carbon technology that uses the earth’s renewable geothermal energy to heat and cool buildings, with an ef?ciency 3 to 4.5 times that of conventional systems. These high performances are achieved by exchanging heat with the earth using a ?uid that is groundwater, surface water or closed loop water. Expensive installations, such as water wells or buriedcoils, are however necessary to transport the ?uid in and out of the earth, making ground-source heat pumps more costly than conventional systems. Installation costs can be reduced in mining environments due to the abundance and the accessibility of resources to be used with heat pumps. Examples of system design calculations using data from the Mouska and Doyon mines in Abitibi show signi?cant installation cost savings using dewatering mine water or ground heat exchangers installed below oxidizing waste rocks. Ground-source heat pump technology is reviewed and scoping calculations are presented to illustrate how such systems can be installed in mining environments.

Jan 1, 2010