Search Documents

By F. W. Gray

Foreword: It is not my purpose, in this address, to write the history of the Geological Survey of Canada, which has from time to time been reviewed by the officers of the Survey itself, and by men more competent than myself to handle so large a subject, but rather to set out some of the reasons for the regard in which the Survey is held by our Institute, the body best qualified to speak for the mining men of Canada. And, a further purpose is to publish the desire of our Institute that the work of the Survey shall be maintained at the highest pitch of efficiency the resources of our country. will permit, because to scrimp expenses on the Survey is 'to save at the spigot and lose at the bunghole." A historical examination of the grounds on which it may be asserted the Geological Survey has been, and still is, of fundamental economic value to our country, discloses a prescience on the part of the forefathers of Canada, calling for our admiring gratitude, and reveals a unanimity among the real leaders of Canadian thought, on the value of geological knowledge, that is impressive in its continuance dawn to this date. There seems always to have been before our people the realisation that large stretches of Canada are unfitted for agricultural settlement, and that our glaciated areas, the barrens and tundra of the North, and our extensive mountain ranges, had promise of compensating mineral content which the geologist and the prospector, labouring together through the years, would disclose. The Geological Survey is one of Canada's oldest public services, distinguished by an unimpaired tradition of honourable and useful labour. Founded in 1843, under William Edmond Logan, not yet 'Sir William', one year after the Act of Union, it was directed by him until 1869, or into the early years of Confederation, so that the early years .of the Survey were also, politically, the formative years of Canada, as we know her today.

Jan 1, 1932

By Lionel Roberge, Borge J. G. Fredriksson

"Late in 1981, a six-rope friction hoist was installed in the Number 2 shaft at Les Mines Seleine Inc. on the Madeleine Islands in Quebec. This paper deals with the reasoning behind the selection of hoisting equipment from the economical point of view, safety point of view, future needs point of view, etc.After establishing the basic parameters for the hoisting system, features of the most common types of hoists (i.e. single-drum hoist, double-drum hoist, Koepe hoist) are briefly laid out. The reasons for selecting a friction (Koepe) hoist are summarized. However, why go for a six-rope hoist rather than the (in North America) more common four-rope hoist? As the subject hoist is the first six-rope hoist in Canada, this question is studied in more detail, covering initial cost, maintenance cost, etc., as well as practical aspects, such as safety, physical dimensions, etc.In summary, experiences from other multi-rope hoist installations world-wide are presented.BackgroundIn 1980, Seleine Mines Inc. was established as a subsidiary of SOQUEM. The new mining company was to develop and operate a salt mine and associated harbour on the Madeleine Islands in the Gulf of St. Lawrence. The Madeleine Islands form part of the Province of Quebec. The mine has a planned annual output of 1.2 million metric tonnes of salt, with reserves in sight for over 20 years. Mining will be by room and pillar, with an underground primary crusher and treatment plant. From the underground treatment plant, the salt will be transferred via conveyors to a 5.5-metre-diameter circular shaft and hoisted to the surface. Surface transportation to the warehouse will again be via conveyor, and a conveyor will also transport the salt from the warehouse to the point of shiploading."

Jan 1, 1983

"In 1989, improved milling and recoveries resulted in a record production of 7 722 200 Ib Nb2P5 at the Niobec Mine. At the beginning of 1990, proven and probable reserves stood at 11 952 000 tons grading 0.65% Nb205. This year, the world steel market has slowed and as a result, niobium consumption is down. Consequently, production at the mine dropped 14% for the second quarter.IntroductionThe Niobec Mine is located approximately nine miles northwest of Chicoutimi, Quebec, (Fig. I). After ten years of production, the Niobec Mine is the only operating niobium mine in North America and the second largest producer of niobium in the world after Brazil.The Niobec Mine is a joint venture held equally by Teck Corporation and Carnbior. Teck Corporation operates the mine while Cambior is responsible for marketing and selling the niobium pentoxide concentrate (Nb2P5).The deposit was discovered in 1964 following an airborne radiometric survey in search of uranium. However, mining of the deposit did not begin until 1976. The initial production capacity of 1500 tons per day was increased several times to the present capacity of 2450 tons . The deposit is considered as an ample source of pyrochlore concentrate for at least 15 years at the present production rate.Niobium, also known as columbium, is a greyish-white metal used primarily as an alloy in various steels and other metals. The use of niobium in alloys heightens tensile strength and improves corrosion resistance while at the same time reducing the weight of the alloy. Niobium is also used in the fabrication of steel for the aerospace, automobile, and oil and gas pipeline industries. Although substitutes for niobium exist, their use often results in diminished performance and net cost increases."

Jan 1, 1990

By S. Banisi, A. R. Hasankhoei, Gh. Parsapour, A. R. Ghasemi

At the Gol-E-Gohar mining and industrial Company, a pelletizing plant, which includes two parallel dry closed grinding circuits and a pellet production circuit, produces 600 t/h. Each grinding circuit consists of a burner, a dry ball mill (6 m×13 m) and an air separator. Each ball mill consists of a 2 m-long dryer chamber and an 11 m-long grinding chamber. Iron ore concentrate is fed to the drying chamber to decrease its moisture from 2.5% to below 0.2%. The drying chamber consists of 56 flights in two rows. It was found when the feed moisture content decreased from 1.3 to 3.5%, the throughput decreased by 14% (40 t/h) indicating a low performance of the dryer. In order to improve the efficiency of the drying section, a scale down version of the dryer was constructed in a 1m diameter mill with a transparent end to make image analysis possible. It was found that because of the inappropriate veiling profile in the drying section, most of materials are not subjected to the hot gas tunnel. To overcome this problem, various flights with different geometries were physically tested and also simulated by the KMPCDEM © software. With the aim of arriving at a proper veiling profile which maximizes the particles contact with hot air, a new flight design was obtained and tested. The installation of the rectangular tooth type flights in one of the mills in the plant made the comparison of the old and new designs possible. The evaluation of the designs in a period of three months indicated 15 t/h increase in the throughput in the case of the new flight design.

Jan 1, 2016

By G. Landry

"IntroductionThe Cape Breton Development Corporation (CBDC) is constantly searching for new technologies that will enhance the marketability of its coal. One technology which shows promise in utilizing Cape Breton coal while at the same time addressing the traditional problem of high sulphur inherent in the Sydney coalfield, is coal-water fuel (CWF).The CWF process incorporates a physical change of coal by grinding it to a flour-like consistency and then mixing additives with it to make a fine coal slurry. The result is a liquid dispersion of fine coal particles that looks like oil, stores and flows like oil but burns like coal. The equipment used in the CWF process is standard mineral processing equipment but application of the equipment to manufacture a specific coal particle size and the specified additives used in the mixing make it a unique technology.The product, which CBDC calls Carbofuel, consists of 70% coal, 29.5% water and 0.5% chemical additives. The key properties of the product are: (I) high solids loading, (2) medium viscosity levels, (3) stability against sedimentation, and (4) good atomization behaviour. Carbofuel specifications are presented in Table I. Carbofuel ProductionThe production of Carbofuel is based on the controlled processing of coal. This involves wet grinding of the coal to a specified fine size (-250 um), cleaning this fine product to remove mineral impurities and formulating (with chemical additives) a finalproduct from the cleaned coal. The flow diagram in Figure 1 indicates the processing circuit for Carbofuel production.CBDC operates a 7-tonne-per-hour continuous production plant complete with state-of-the-art control, full laboratory services, product storage and loadout facilities. The plant has operated since 1983 and has produced over 12000 tonnes for several major demonstrations. The plant is shown in Figure 2."

Jan 1, 1987

By J. Wild, M. Ounpuu, G. Chevalier

"The requirements for a finer grind at Heath Steele have resulted in the investigation of agitated milling as a cost effective alternative to conventional tumbling ball mills.The grinding unit is a vertically agitated, or stirred ball mill. Grinding occurs as the result of the motion of a single vertical rotor equipped with protruding pins which impart a stirring action to the ball charge. A comparative evaluation of a 30 kW SALA Agitated Mill (SAM), and a 1.5 m x 2.5 m copper-lead regrind ball mill has been conducted at Heath Steele.An overview of agitated milling as it applies to the reduction of sulphide ore will be the primary topic for discussion. Specific parameters including energy efficiency, media consumption, operating costs, and the mechanical aspects of the SAM operation will be presented.Evaluation of the agitated mill has shown that improved grinding performance at much lower work indices than those of the conventional ball mill is possible. Media consumption has proven to be comparable on an average g/kWh basis, but the mechanical availability of the mill has been low.INTRODUCTIONConventional tumbling ball mill grinding has proven to be an energy inefficient process. Energy losses occurring within the ball mill itself can be attributed to particle friction without breakage, kinetic and potential energy losses, plastic and elastic deformation and the production of heat and sound (Lynch, 1977). It can be generally stated that a certain amount of the input energy will be converted to another form as a necessary by-product of particle breakage. Theoretical interpretation of experimental results indicate that the energy required for breaking the ore particles in a ball mill varies between I% and 25% of the total energy input (SME, 1985)."

Jan 1, 1993

By H. A. Wilson

Introduction Salt (sodium chloride) occurs naturally either in the solid state as rock salt or in solution as a component of natural brines. It is the major saline constituent of sea water, which contains about 4 percent salt-roughly 164 million tons, or enough to meet world salt demands for five years, per cubic mile. The great rock salt deposits of the world are generally regarded as having been formed by the evaporation of sea water over long periods of rime in wholly, partially, or periodically cut-off bays of ancient oceans. History and Occurrence of Salt in Canada We can speak today of the vastness of Canada's salt resources, but it was not always so. Settlement of our Atlantic seaboard and the Sr. Lawrence valley began in earnest in the early 1600's. The first small commercial salt works in Canada did not come into operation until 1866. Thus, for some two and a half centuries, the inhabitants of this growing country were entirely dependent on foreign sources for every pound of salt they consumed. The record shows that from at !east 1800 onward, the need for a domestic salt industry was clearly recognized by the governments of the day. It was during the Western Ontario oil-boom of 1866 that the initial discovery of rock salt in Canada was made, not far from Goderich, at a depth of 1,000 feet. A salt company was promptly organized, and with their operations there began the gradual and still uncompleted conquest of the Canadian salt market by the Canadian salt industry. Over the next thirty years many holes were drilled into the Salina formation both in Ontario and Michigan, and encountered rock salt. A vast salt-basin was disclosed, approximately outlined, and given the name Ontario-Michigan Salt Basin. The Ontario portion of the basin extends over at least 3,500 square miles, is met with at a depth varying between 800 and 1,600 feet, and has a thickness of 50 to 250 feet. No attempt has ever been made, so far as we know, to calculate the total salt reserves of this basin, but the minimum indicated in the Ontario portion by the figures just cited is just under thirty-five cubic miles. The specific gravity of rock salt is 2.2. From these data, those so inclined may calculate the tonnage.

Jan 1, 1947

By M. P. Amsden

"Ecstall Mining Limited, a subsidiary of Texasgulf, Inc., Operates the Kidd Creek Mine, Concentrator and Zinc Plant at Timmins, Ontario. Two different ore types are mined and milled to produce concentrates of copper, zinc, lead and tin. The ores are processed at the Concentrator in three separate individual milling circuits, each with the capacity to treat up to 3500 tons per day. Two circuits treat copper-zinc ore 1t an average combined rate of 6500 tons per day and the third circuit treats 3500 tons per day of silver-lead zinc ore. Conventional crushing, grinding and flotation procedures are followed. The purpose of this paper is to describe Ecstall's experience with rubber mill linings in the grinding circuits.CrushingBoth ores are crushed to minus 6 inches at the Mine and delivered by rail to the Concentrator where they are reduced by secondary and tertiary crushing to minus 5/8 inch.GrindingThe crushed ores are prepared for selective flotation by grinding with rod mills and two stages of ball milling. flotation circuit middling products are reground in regrind mills prior to further treatment. A typical flowsheet of one of the grinding circuits is shown in Figure 1.All the grinding units are Allis-Chalmers Mills. The rod mills are 10 1/2 feet diameter by 16 feet long. Both the primary and secondary ball mills are 12 feet diameter by 18 feet long and all regrind mills are 6 feet diameter by 12 feet long. The primary mills are charged with 1 13/16 inch forged balls. Secondary mills are charged with 1 1/2 inch forged balls and the regrind mills are charged with 1 inch forged balls. All cyclones are Kreb units. The primary cyclones are Dl5B hydrocyclones, the secondary cyclones are D6B hydrocyclones and all regrind cyclones are D6B hydrocyclones."

Jan 1, 1974

By Z. Abbasloo, A. Masoomi, L. Ebrahimi, A. Mortazavi, A. Keshavarz

"Investigation and 3D analysis of Heap no. 2 of Meydook copper complex was the subject of this study. In this project all geological and geotechnical investigations conducted in the mine were evaluated aiming at determination of Heap no. 2 design parameters. The main objective of the project was to evaluate the potential for construction of Heap. No. 2 on a waste dump built in a valley in the north side of the pit.Considering the space limitation for dump location this was a viable alternative to reduce the costs associated with heap no. 2 construction. Moreover, it allowed for a significant reduction in overall mining costs. Considering the project condition, a 3D analysis of heap major structures including; valley rock foundation, waste dump, and low grade ore was carried out. Five sets of analyses were conducted and the displacement and stress fields were calculated within the heap no. 2 components. In all analyses conducted the subsident profile was determined for the valley base rock and heap foundation (waste dump). Moreover, the shear interaction between heap and waste dump was evaluated at the heap interface. The analyses results showed that the maximum settlement at the heap base is about 4-5 cm and the waste dump provides a safe and reliable base for heap construction. Moreover, the analysis results showed that the selected %5 grade for the heap interface is good and does not pose any risk in terms of heap Interface shear displacements. A sensitivity analysis of heap mechanical parameters was also conducted. The obtained results show that if the friction angle of heap material is reduced below 25 degree due to acid spraying process, the heap walls become unstable and the heap geometry must be redesigned."

Jan 1, 2015

By E. J. Marcotte

"INTRODUCTIONThe Upper Canada Mine is located at Dobie, approximately ten miles east of Kirkland Lake, Ontario.The mill contains Upper Canada's cyanide circuit and Upper Beaver's flotation circuit. The combined capacity is 590 tons per day consisting of 415 t.p.d. of Upper Canada gold ore and 175 t.p.d. of Upper Beaver copper-gold ore.The Upper Beaver ore is trucked five miles to the Upper Canada mine site.Crushing:The crushing circuit consists of primary, secondary and tertiary crushing employing one C .A. C. 15 in. x 24 in. Superior jaw crusher, one 4 ft. x 8 ft. Tyler-Niagara double deck screen, one 3 ft. Symons standard cone crusher and one 3 ft. Symons shorthead cone crusher.The -2 in. product from the jaw crusher is fed to the double deck screen. The+ 5/ 8 in. passes over the top deck to the 3 ft. standard cone crusher; the+ 3/ 16 in. material passes over the lower deck to the shorthead cone crusher. The - 3 / 16 in. material pas sing through the lower deck of screens is the product to the mill.The screens used prior to the installation of rubber screen cloths were: one 4 ft. x 4 ft. section with 3/ 4 in. square openings and one 4 ft. x 4 ft. section with 5/ 8 in. square openings on the top deck; two 4 ft. x 4 ft. sections with openings of 3/16 in. x 4 1/2 in. slot on the lower deck. The fine screens were positioned so that the 4 1/ 2 in. slots were parallel to the flow of feed.The crushing circuit is operated on a three shift per day basis by one operator per shift."

Jan 1, 1968

By R. Lepsoe

THE basic products of the Company are lead and zinc. Around 950 tons of these metals are produced each day. In the last decade, the production of by-products has increased to such an extent that they are now nearly as large an operation as that of the base-metals. Of the many by-products, the most objectionable, and up to a few years ago the most useless, was the sulphur. The sulphur comes in the ore from the Sullivan mine. It is in the ore chiefly as lead, zinc, and iron sulphide. By selective flotation, these three sulphides are separated into the lead concentrates, the zinc concentrates, and the mill tailings. These mill tailings contain the bulk of the iron and the sulphur. Of the 6,5CO tons of ore treated per day, about 5,000 tons are wasted to the mill tailings dump, and, while now valueless, will in future years undoubtedly be used as a source of iron and sulphur. There are about 1,500 tons of sulphur and 2,200 tons of iron per day in the tailings, and about 400 tons of sulphur left in the total concentrates. In the recovery of lead and zinc in the pure form, the first step is the roasting operation. Here, most of the sulphur is driven off as sulphur dioxide in the gases. It has always been apparent that this sulphur should be. recovered and utilized if possible. At the same time, this would cure the smoke nuisance. Because, in spite of the low concentration of sulphur dioxide and the fact that it was discharged from stacks at an elevation of 400 feet above the plant, some damage to vegetation close to the plant had been experienced.

Jan 1, 1937

By T. T. Chen, J. E. Dutrizac, G. Poirier

In the Waelz kiln process, EAF dust is converted to an Fe-rich slag, a (Zn, Fe)-rich dust that is recycled to the kiln and the Zn-rich Waelz oxide which is subsequently up-graded for the recovery of zinc. To clarify the reactions occurring, the Waelz kiln products from a European Waelz plant were characterized mineralogically to determine the mineral species present, their micro-textures and the metal carriers. The EAF dust contains 27 % Zn, and consists mainly of ZnFe2O4 and ZnO, together with minor to trace amounts of NaCl, PbCl2, KCl, CaO, Ca2Fe2O5, Fe203, FRO, Pb oxide and various Ca-Fe-Al-Mn silicates. The KCI and NaCI sometimes agglomerate the other particles. The slag consists of nodules which often exhibit colloform structures. The slag contains of variable amounts of Fe, FeO(OH), FeO, gypsum, Ca(OH)2, Ca2SiO4 and various Ca-Fe¬Al-Mg-Mn silicates as well as minor to trace amounts of ZnFe2O4, Cr-Fe oxide, Mn-Fe oxide and other species. The Waelz oxide contains 57-61 % Zn, and consists predominantly of ZnO, with minor to trace amounts of KCI NaCl, Pb(OH)Cl, Pb20(SO4), Pb chloride, ZnSO4, ZnFe2O4, Ca2SiO4, Ca2Fe2O5, Ca-Fe silicate and NaZn4(SO4)(OH)6Cl.6H2O. The KCI agglomerates the other particles in the Waelz oxide. The recycled dust appears to be a mixture of EAF dust and Waelz oxide, but it contains relatively more coarser-grained metallic Pb and Pb oxide particles.

Jan 1, 2004

By D. Royston

In SAG mills fed with a variety of ore types, hard packing between the shell lifters can come and go depending on rock type and rock size distribution and the presence of a binder. Packing can appear in all sizes of SAG mills, and can be tenacious. High ball impact forces (depending on ball size) in larger mills may compact and encourage packing. Packing can have a negative impact on milling performance and a change in shell liner design may be required to remove it. However shell liner design changes need to be managed with care to ensure liner reliability. In smaller mills control of packing can extend shell plate wear-life and may help to maintain milling performance in fixed-speed mills through the liner wear-cycle.

Jan 1, 2012

By E. Best

In 2003, Phelps Dodge Mining Company decided to pursue the design and construction of a Central Analytical Laboratory to provide chemical analyses for their Arizona and New Mexico operations. This centralized approach was selected in place of refurbishing six (6) older laboratories that operated at the various Phelps Dodge sites, and which would not have permitted full automation and use of robotics. The new lab was designed by the Process Technology Center (PTC) Material Characterization Group in cooperation with IMP Group. The Central Analytical Service Center (CASC) encompasses fully automated sample preparation of blast holes and geological samples weighing up to 15 kg/sample. The CASC also includes the first "wet chemistry module" worldwide to be operated by robotics systems to perform Total Cu, Acid Soluble Cu, and Quick Leach Tests (QLT), and a fully automated lab for electrowon copper cathode. The new lab also offers flexibility for handling specialty samples and analyses by either semi-automated or manual mode. Data handling and transfer is accomplished using the commercially available StarLIMS system. Commissioning was accomplished within five (5) months of startup during which the CASC also handled 86% of a full production load. The 24/7 lab operation has already exceeded its design capacity, has achieved considerable savings in operating cost, reduced sample preparation errors, and significantly increased analytical quality.

Jan 1, 2007

By M. Tadie, J. Wiese, K. Corin

The use of potential control in the flotation of ores has been applied in a variety of operations and presents an opportunity for improvement of selectivity and recovery of valuable minerals. Although it is possible to vary the redox potential (Eh) using chemical additives such as sodium hypochlorite or hydrogen peroxide this is more commonly done by varying the pH and dissolved oxygen (DO) concentration. The present study involves an investigation into the effect of varying dissolved oxygen concentration, ionic strength (IS) and pH on the flotation response with the aim of application to a South African lead-zinc ore. In all cases the Eh is measured as a function of the different DO, IS and pH values. The main objective was to achieve selective flotation of galena from sphalerite. The first part of the work was micro-flotation tests conducted on single minerals with galena used as the basis for effect of the factors studied on redox potential and ultimately recovery. The DO was varied by alternating between the use of air and nitrogen as the gas source to the micro-flotation cell. PH was varied between pH 9.2 and pH 11.8 using sodium hydroxide. In the first part of this study a factorial design approach was used to determine the interactive effects of the variables tested, viz. DO, ionic strength and pH, on the Eh and on the recovery. Redox potential was measured using a combination electrode made up of platinum wire and Ag/AgCl reference combination. Recoveries indicated that pH had the most significant effect on recovery and Eh. The influence of redox potential on recovery was found to be of relevance to the condition of high dissolved oxygen concentration and less so at low dissolved oxygen concentrations. It was also noted that that the combined interaction between ionic strength and dissolved oxygen concentration had a positive effect on recoveries, however this was not so with Eh. The chemistry of the ions in solution was observed to play a dominant role on the recovery due to changes in solubility arising to pH modification. The longer term objective of this work is to determine the optimal Eh conditions for the separation of galena from sphalerite.

Jan 1, 2016

By C. Robinson

The Diavik Diamond Mine is located in one of the most remote and forbidding places in the world, 220 kilometres south of the Arctic Circle and on the bed of a vast northern lake, Lac de Gras. A single road, built out of ice and crossing frozen lakes, connects the mine with other operations and Yellowknife, the capital of the Canada's Northwest Territories. Diamonds were first discovered in the Lac de Gras region in the early 1990s, and construction of the Diavik Diamond Mine was completed in 2003. Diavik currently mines three kimberlite pipes. Open pit mining has now concluded and all three pipes are mined using underground mining methods. In early 2010, Diavik began mining and processing initial ore from its new underground mine; underground mining operations are expected to continue beyond 2020. The initial mine ventilation system was an exhausting (pull) system with fresh air supplied by a fresh air raise and a main ramp. Return air was exhausted via two raises and a secondary ramp. The system had a total flow capacity approximating 401-411 m3/s. With planned increased production and with changes in mining method, it has been proposed to change the mine ventilation system to a positive (forcing) ventilation system in order to meet projected increases in flow requirements of 566-708 m3/s. Extensive engineering work was developed in order to successfully achieve the changes in system configuration. In the proposed configuration, the main ramp is in an exhaust configuration and exhaust raises are converted to fresh air raise. A number of system implementation options were investigated and phased plans for system execution have been developed. The proposed changes to the ventilation system are substantial and involve extensive construction work. Work was commenced in 2011, each planned phase has been successfully completed to date, and system changes continue today in order to achieve complete system flow reversal and increased flow distribution. This paper details the design of the modified ventilation system and commissioning work which will allow the mine to meet its future production targets.

Aug 1, 2013

By Marke Wong

? Vietnam?s economy is growing so fast that gross domestic product (GDP) growth remained above 8% in 2005 and exports are rising steadily at 25% per year. ? Demand for electricity is expected to increase 18% per year through 2010 requiring an additional estimated 7,547 MW before 2010 ? Domestic coal demand is expected to be over 45 Mt by 2010. ? The Quang Ninhcoal deposits are estimated at 6.5-7 billion tons (350m) Vietnam News Agency. Saturday, May, 6, 2006. ? National resources are now estimated at 10 billion tonnes; not including a relative new coal bed discovery estimated at 210 billion tonnesin the Red River Basin.

May 1, 2006

By Bernard Tougas, Franco Chiesa, David Levasseur, Bernard Duchesne

"In the present paper, the optimization of a tilt poured permanent mold will be carried out using filling and solidification modeling. This exercise resulted in 3 modifications of the initial mold design which was based on the foundry experience. The optimization provided a 20% improvement in the yield while increasing the output from 10 to 15 castings per hour.In a subsequent study, the value of the critical fraction solid of AlSi7Mg (A356) alloy was verified by radiographic analysis of the castings produced in the first 5 cycles of a run, which are necessary to bring the mold to a dynamic thermal equilibrium."

Jan 1, 2014

Agenda 1.Energy consumption and energy costs ?focus and failings 2.Energy efficiency methodologies, people and supporting tools 3.Energy cost saving case studies from three minerals processing plants 4.The operations team and the supporting role of Operations IT 5.Conclusion: Reducing energy consumption and energy costs There are many good Energy Efficiency Methodologies ?Energy and GHG Emissions, Management Guidance Document, The Mining Association of Canada ?Energy Savings Toolbox ?An Energy Audit Manual and Tool, Canadian Industry Program for Energy Conservation (CIPEC) ?Lean and Energy Toolkit, Achieving Process Excellence Using Less Energy, www.epa.gov/lean ?Energy Efficiency Opportunities Assessment Handbook, www.energyefficiencyopportunities.gov.au

May 1, 2010

By Robert MacPhail, Louis Racine, Bret G. Cousins

"Sodium Isopropyl Xanthate is employed in a wide variety of sulphide flotation procedures due to the specificity over other xanthates and the cost savings over other sulphide collectors such as thionocarbamates, xanthogen formates and dithiophosphates. An investigation carried out by Tennants Research Technology Applications (TRTA), has produced a chemically enhanced SIPX that has shown all the advantages of normal SIPX along with improved recoveries.Currently, FLEX 31 is manufactured at the Prospec Chemicals xanthate plant in Fort Saskatchewan, Alberta, Canada. Prospec, founded in 1983, produces approximately 4500 tonnes of xanthates per year and is presently undergoing expansion to produce approximately 6000 tonnes. The proprietary process for FLEX 31 is a new addition to plant operations that include the production of xanthates, thionocarbamates and xanthogen formates.This paper will cover the testwork on the zinc flotation circuit at the Louvicourt Mine in Val d'Or, Quebec. This testwork indicated that FLEX 31 could replace SIPX due to the ability of the FLEX to improve zinc flotation kinetics without adversely affecting final concentrate grade. FLEX has presently replaced SIPX in the zinc circuit at Louvicourt.BackgroundThe Louvicourt deposit is hosted by greenschist facies Archean volcanic rocks located in the southeast portion of the Abitibi Greenstone Belt. In the Val d'Or area, the volcanic rocks form an east-west striking, steeply dipping and south-facing sequence composed of thick mafic and ultramafic flows of the Lower Malartic Group.The joint venture has three partners-Aur Louvicourt Inc. (30%), Novicourt Inc. (45%) and Teck Corp (25%). Aur Resources holds 30% interest through Aur Louvicourt, a wholly owned subsidiary and is the operator of the project. Novicourt Inc. is 60.9% held by Noranda.Approximately 75% to 85% of Louvicourt's revenue comes from the sale of copper; 10% from gold (in the copper concentrate); 7% from zinc and 3% from silver (also in the copper concentrate) The copper at Louvicourt is fairly ""fast floating"". About 60% of the copper in the ore can be concentrated in the first flotation cells with feed grades of approximately 4% copper.The initial testwork and pilot trials had indicated that it would be difficult to achieve zinc grades over 52% and recoveries would have to be kept at a level amenable to salable concentrate grades. The actual mill results, with a fine regrind, achieved zinc grades of 55% to 56% at about 75% recovery."

Jan 1, 1996