Search Documents

By G. Dubé, A. Leclerc, P. Quinn, G. E. Agar, J. Y. Clouthiér, J. D. McLaughlin

"Gold dissolution by cyanide requires the presence of oxygen which is usually supplied by sparging compressed air into the gold containing slurry. For those ores that contain certain obnoxious substances that consume oxygen, maintaining the required minimum level of dissolved oxygen can be troublesome. One of the most economical solutions to the problem of low dissolved oxygen, especially in plants that have air compressors installed, is to enhance the rate of oxygen mass transfer.The oxygen mass transfer rate was measured in a two phase system using two different sparger arrangements, and with addition of a frother that is known to reduce the bubble size produced by the sparger. The common sparger system was shown to be inefficient compared to a readily available but under utilized method of gas dispersion which introduces air directly below the reactor turbine. Transfer of this technology to an operating plant confirmed the beneficial effect of the improved sparger system. The addition of the frother did decrease the bubble size, but it also reduced the oxygen mass transfer rate."

Jan 1, 1993

By S. C. Cohen, A. F. Mikkelsen

"This paper describes the improvements made to the operation of a liquid phase, 300°C, heat transfer system in the paste plant of an aluminum smelter. These improvements were achieved by replacing the original heat transfer fluid, a synthetic aromatic, with a new technology, petroleum-based product. This new fluid, Calflo HTF, provided better thermal stability, with lower toxicity, and improved plant working conditions.The procedures for fluid selection, changeout and performance monitoring are described along with a summary of control analysis over the last three years."

Jan 1, 1993

By Fathi Habashi

"On August 3, 1888, German Patent No. 43977 entitled ""A Process for the Production of Aluminum Hydroxide"" was issued*. The discovery which led to the patent was made by the Austrian chemist Karl Josef Bayer (1847-1904) (Fig. 1) who was at that time in Russia, and the process became known as the Bayer Process in his honour(1)(2)- The process imediately achieved industrial success, displacing the pyrometallurgical process that had been used until that time to produce alumina. The Bayer Process involved the pressure leaching of bauxite with NaOH solution to obtain sodium aluminate solution from which aluminum hydroxide was precipitated by seeding. Today bauxite is not only the principal source of aluminum but also of gallium, both metals being effectively recovered by the Bayer Process. The purpose of this paper is to outline the historical background of this discovery and its importance to hydrometallurgy."

Jan 1, 1999

By K. Adham, T. Buchholz

"Significant capacity increases to meet new production demands can often be fulfilled through debottlenecking of an existing production facility, rather than the more expensive option of building new plants and facing new environmental and infrastructure challenges. To achieve that goal, it is important to model and calculate the existing ultimate capacity of each processing plant area, and that of each key equipment sector within the plant areas. This paper describes a methodology of how process modeling tools can be used to simulate the processing steps, how to estimate their existing and ultimate capacities, and how to determine the sweet-spots (minimum cost points) for a plant expansion – leading to a road map of the subsequent debottlenecking project implementation.The debottlenecking technique is presented through a generic work-flow narrative which can be applied to different mineral processing studies, starting with establishment of heat-and-mass balances, drawing a bottleneck diagram, brainstorming capacity increase options, and preparing a cost-capacity curve. Hatch has successfully applied this technique to a number of plant capacity studies, with great benefits to our industrial clients.INTRODUCTIONWith the softening of the metals and minerals prices, and the escalated costs of building new processing plants, it is now economically more viable to improve and debottleneck the existing facilities, rather than build new ones. However, spending new money on old plants requires careful considerations, in order to identify the most economically advantageous incremental steps of improvement and the best potential returns on investment. Process modeling, hand in hand with plant measurements, can identify the best scenarios to balance the three aspects of plant capacity (nameplate, utilization and yield), both at the global and the individual system and subsystem levels."

Jan 1, 2016

By T. R. Skerry, H. P. Hudson, T. E. Warren

"ALTHOUGH coal is generally the cheapest fuel on the basis of heating value it has been at a disadvantage in competition with other fuels because means have not been available for efficient •Conversion of its thermal energy to mechanical work. Taking the •railway application •as an example, the cost of Diesel oil is about three times that of its thermal equivalent in coal, but the overall efficiency of a Diesel locomotive is about five times that of a coal-fired steam locomotive. Accordingly, the Canadian railways are replacing all coal-fired steam Locomotives, as they are retired from service, with Diesel units. This conversion in itself represents a major loss to the coal industry because the value of railway fuel is approximately 130 million dollars per year, and there are other applications in the medium power range where oil is displacing coal. There is, therefore, a strong incentive to attempt development of an efficient coal-burning engine.Coal has never been a promising fuel for reciprocating internal combustion engines because of the time required for its combustion in pulverized form . This is not less than one-tenth of a second so that the speed of such an engine would have to be very slow. There are also serious difficulties of a mechanical nature arising from the necessity for intermittent combustion and the use of close-fitting pistons."

Jan 1, 1952

By G. Mucsi, J. Faitli, K. Bohács

"The authors developed an online tube rheometer to supplement a Netzsch MiniCer (Netzsch GmbH, Germany) stirred media mill in order to monitor online the rheological characteristics of the suspension and therefore the result of grinding during the process. Previously it was demonstrated that the above measuring system was working appropriately based on the preliminary tests. The product related stress model was applied for the evaluation of the grinding results. It was found that the suspension concentration and the change of the material properties during grinding, consequently the rheology strongly affects the grinding result, i.e. specific surface area, median particle size as well as specific grinding energy. The tested model limestone – water suspensions behaved Newtonian initially, then after a given grinding time their properties had changed and they become Bingham plastic. INTRODUCTIONStirred media milling now is a common practice to produce fine and ultrafine granular materials for different purposes. With an increasing demand of ultrafine powders for industries (Kwade, 1999), wet and dry ultrafine grinding has been increasingly used in various fields, such as minerals (Mucsi, Rácz, & Mádai, 2013)(Rácz, 2014), ceramic materials (Becker & Schwedes, 1999), pigments (Ohenoja, Illikainen, & Niinimäki, 2013), chemical products (Baláž et al., 2013), microorganisms (Kwade & Schwedes, 2002) and pharmaceutics (Afolabi, Akinlabi, & Bilgili, 2014). It is well known that suspension rheology affects the wet comminution of materials (He, Wang, & Forssberg, 2006a). The rheological behaviour of the suspension containing the ground particles might indicate the level of interparticle interaction or aggregation and therefore it is an important variable factor of the process control (Muster & Prestidge, 1995). The influence of the rheological behaviour of mineral suspensions on their grindability has attracted more and more interests and attention, especially on ultrafine grinding performance (He, Wang, & Forssberg, 2006b) (Bernhardt et al., 1999). However, there are still many issues concerning the machine and the process for the different applications. When grinding is effective and the particle size range decreases significantly, the circulating suspension is becoming typically non-Newtonian. The changed rheological behaviour and the increasing rheological material parameters can negatively affect the grinding efficiency; therefore it is an important issue. Ultrafine stirred media milling as well as solid-liquid two phase flow have been studied for a long time at the Institute of Raw Materials Preparation and Environmental Processing of the University of Miskolc. Regarding ultrafine grinding the research is focusing on the description of materials’ grindability (energetic aspects) both in wet and dry circumstances (Mucsi et al., 2013; Rácz, 2014). Concerning rheology, the three measuring pipes tube rheometer was developed decades ago (Faitli & Gombköto, 2015). So far many different solid materials from all over the world had been tested in this rheometer (Faitli & Gombköto, 2015). Main aim of these tests was to gain basic data for large scale hydraulic transport applications. Among the many stirred media mills there is a Netzsch MiniCer mill at the Institute. It was reasonable to combine the two fields together, and the goal of the research presented in this paper is to develop an online tube rheometer for the Netzsch mill and to carry out grinding and rheological testing simultaneously."

Jan 1, 2016

Applications of proven real time, through-conveyor elemental analysis technology and benefits achieved will be discussed using case studies in base metals, iron ore and phosphate operations. PGNAA (Prompt Gamma Neutron Activation Analysis) technology and its background in minerals applications and applications which are expected to further improve its utilization will be reviewed. Short payback through operational benefits such as removal of waste from feed, increased feed grade and overall improved productivity will be demonstrated based on results achieved at several processing operations. PGNAA technology is most applicable to conveyed flows as it is unaffected by belt speed, particle size, segregation/layering, mineralogy or dust. As a transmission method able to penetrate in excess of 500mm of rock it provides extremely representative results continuously measuring through the full conveyed cross section and reporting results typically on one to five minute accumulated increments to the control room. Multi-elemental results and moisture content are used for active process control: diverting conveyed flow increments(bulk sorting), blending ore types in plant feed, and providing advance warning of significant quality changes to the downstream plant operators (e.g. flotation). Elements of interest may include deleterious components as well as target metals. Ore feed quality measurements are also useful in metal accounting, ore reconciliation and real time feedback to mining operations. Further benefits can result when combined with other technologies such as particle sorters, to upgrade diverted increments of subeconomic material to achieve higher feed grades and lower deleterious content to the main process. Measurement of elements (e.g. silica) which correlate with ore hardness or grinding characteristics can be used to moderate feed rate to grinding mills to prevent overload, hence optimizing grinding performance and reducing energy and grinding media consumption. Pebble flows can be analysed and uneconomic increments diverted to prevent recirculating flows consuming mill capacity unnecessarily. This also increases average feed grade.

Jan 1, 2016

By D. F. Zhang, X. Q. Jiang, N. Tahreen, D. L. Chen, F. S. Pan, D. Y. Li

Alloying with rare-earth elements has been proven to be an important tool for magnesium to achieve superior properties via texture randomization. The role of yttrium in texture weakening and the link between texture and formability are fairly well known. Since annealing is a vital part of metal processing which could significantly contribute to ductility, it is important to ascertain the impact of annealing in terms of texture change. Also, an understanding about texture development during pre- and post-deformation annealing is essential to improve the industrial deformation processing as texture is closely related to formability. While there is independent information in the literature regarding the effect of rare-earth addition and heat treatment on the texture formation, no systematic studies have been reported on the collective impact of yttrium addition, annealing and deformation on texture evolution. The present study was, therefore, aimed to identify the inter-relationship among texture evolution, yttrium content, heat treatment and deformation behavior in an extruded Mg-Zn-Mn-Y alloy. Annealing at 450°C for 1 hour and uniaxial compression tests at a certain amount of deformation were performed. The deformed and annealed samples were then subjected to annealing and compression test, respectively, followed by texture measurements. It was observed that yttrium addition effectively weakened the crystallographic texture in all conditions, which was evident from the changes in the microstructures and textures.

Jan 1, 2015

By Michel Masse

1. A battery-powered wireless mesh network for dynamic diesel machinery tracking and operating status monitoring. 2. A real-time ventilation model and fan speed optimizer. 3. An OPC server for information interchange. 4. OPC linkage to existing control infrastructure. 5. A Human Machine Interface (HMI) providing data archiving, trending and reporting. 6. Live MS-Excel to interrogate the simulation, controls and optimizer. 7. The battery-powered network mesh also provides SCADA functionality to route optimized setpointsto the fans and automated regulators not linked to PLCs.

Feb 1, 2008

By V. Schenk

Dust exposure resulting from the exploitation and winning of natural resources below ground has presented a serious health problem since the beginning of mining. The boom phase of the German hard coal mining industry after World War II with at times up to 500,000 employees saw an increase of dust exposure of miners below ground as the mechanization of road heading and mining increased significantly. More and more miners were diagnosed with coal-workers-pneumoconiosis (CWP), a chronic and irreversible lung disease resulting in a significant impairment of pulmonary function. This realization led to a reduction of CWP in the German hard coal mining industry in the 1960s. The successful fight against CWP began with the introduction of technical dust prevention measures. By infusing the coal seam with water before mining, sprinkling and spraying of heading and mining machines as well as canopies with water, aspiration in places with high amounts of dust and the suppression of dust with chemical substances it is possible to significantly reduce the miners? dust exposure. All operating points below ground are checked and measured regularly with regard to dust exposure. Through the combination of these values together with the individual shift data a relatively precise profile of individual dust exposure can be obtained. This profile allows the targeted work assignment when certain predetermined limits have been reached, moving the miner to a work place with less dust exposure and thus reducing the chronic dust exposure. The state of health of the individual is known because since about 60 years ago extensive occupational health checks have been carried out regularly at least every two years which means that work restrictions can be imposed depending on the findings. Since the beginning of the 1980s more value has been attached to not only situational but also behavioral prevention. Given the comprehensive provision of protective masks, having a protective effect as well as the required comfort when being worn, each miner has the opportunity to protect his respiratory organs depending on the specific dust exposure. Through a combination of all these measures the German hard coal mining industry has succeeded in beating the classic coal miner?s disease CWP. For mines in the Ruhr valley this means that a miner who started work after 1978 will no longer develop CWP.

Aug 1, 2013

By F. Cheuk, E. Krause, V. G. Papangelakis, G. A. Moldoveanu, S. Abendschein

Systematic studies have been conducted at the University of Toronto in order to evaluate lanthanide extraction from clay minerals from different geographical regions. It was found that rare earth elements (REE) are easily recovered into an aqueous solution via an ion exchange mechanism by leaching with electrolyte solutions containing monovalent cations under ambient conditions. In this study we assessed extraction levels of individual REEs as a function of initial clay composition and leaching conditions. It was found that, in spite of variations in clay origin, all clays consistently reached peak REE extraction levels with fast kinetics. However, terminal extractions were clay-specific. The feasibility of using seawater as a leaching solution and potential synergies with ammonium sulphate as a lixiviant was also investigated. Seawater was found to be inferior to using ammonium sulphate, and provided no observable synergy in leaching performance when used together. The aqueous phase trapped in leached clays was shown to contain significant amounts of REE, as demonstrated in clay washing tests. Techniques to improve the REE concentration in leachate through process variations were investigated. However, it was found that most techniques capable of increasing REE concentrations in the resultant leachate also resulted in reduced REE extraction.

Jan 1, 2014

By Yongfeng Jia, Shaofeng Wang, Danni Zhang

Ferrihydrite is ubiquitous in soils, groundwater and aquatic sediments and is usually classified as "2-line" or "6-line" according to the number of diffuse XRD peaks. It has high surface area and reactivity; therefore, it may serve as a sink for sequestering trace metals, metalloids and organic matters via adsorption and co-precipitation. Although considerable attention was paid to the transformation process of this thermodynamically metastable solid, there are still some controversies on the mechanisms of the formation of goethite or hematite from the ferrihydrite precursor. This work systematically investigated the transformation of 2-line ferrihydrite produced by using different neutralization regent (CaO vs. NaOH) into crystalline products at different pHs (4, 7 and 8), three temperatures (25, 40, 75 °C) and in different media (sulfate vs. nitrate). X-ray diffraction (XRD), Raman, Fourier transform infrared spectroscopy (FTIR) and chemical extraction were employed to characterize the transformed solids as well as the redistribution of Fe between the amorphous and more crystalline phases. The results showed that the transformation product in nitrate media was hematite (major) and goethite (minor), which was independent of pH, temperature or neutralization reagent. In sulfate media, goethite was the dominant solid under slightly acidic conditions (pH 4) with 6-line ferrihydrite as the intermediate product, whereas neutral to slightly alkaline conditions still favor the formation of hematite. Chemical extraction results indicated that there was only ~3 % of amorphous phase detectable after aging at 25 °C for 280 days at slight acidic pH. In contrast,~70 % of the iron remained as an amorphous phase under neutral to slightly alkaline conditions. The results suggested that the pH as well as the reaction media (sulfate ion) plays an important role in the 2-line ferrihydrite transformation process.

Jan 1, 2016

By David Meadows, Elmer Palmer, Steve Dixon

As part of the Goldcorp Inc growth plan Minera Peñasquito SA de CV has developed its polymetallic deposit with a large “state of the art” concentrator to process lead and zinc ores. The plant consists of two grinding lines including 38ft diameter SAG mills and 24ft diameter ball mills. During mid to late 2009 concentrator commissioning activities commenced. First concentrates were produced in October 2009 and now the plant is meeting its design basis of 65,000 mtpd per line. This paper describes the design and operational experience to date for its grinding circuit design, together with the recently commissioned HPGR crushing circuit.

Jan 1, 2012

By A. Diaz, Minera Los Pelambres, C. G. Salinas, G. Leinenweber, F. Diaz, D. Rojas, R. Bernal, O. Jimenez

"Los Pelambres Mine (MLP) is located in the IV Region of Chile, a semi-arid region where water plays a key role in operations as a scarce resource and is vital for the sustainability of human life, animals and ecosystem. The conventional flow meters installed on pipes at MLP can fail to provide an accurate measurement due to corrosion and/or fouling on the inner wall or presence of elements in the water such as acids, salts and suspended solids. Conventional flow measurement methods require the inner diameter to be known, however it is not always possible to assess its real value due to scaling, fouling, corrosion, etc. Here we present a novel methodology to solve these problems, which consists of the measurement of flow by a method that does not require the internal area of the pipes: the fluorescent tracer dilution method. In addition, the fluid velocity can be determined by the transit time of a radioactive tracer method. With the flow rate and velocity, the equivalent area is determined and thus the equivalent internal pipe diameter as well. This methodology was applied in a recirculation pump station, for mineral processing from the El Mauro tailings dam.This work demonstrated adequate correlation between measurements from fluorescent tracers and velocity measurements from radioactive tracers, both of which lead to the assessment of the internal diameter of pipes with scaling. The results of both methods disagree with the data provided by the flowmeter installed on the line due to its miscalibration. This information is useful in validating and correcting the information provided by online flowmeters of all water and solutions transport processes in filled pipes.INTRODUCTIONPresently, the need to optimize water resources is increasingly ever important, due to various reasons such as water scarcity, community empowerment, an increased use of water for mining processes and environmental considerations. Taking into account those main considerations, Los Pelambres Mine decided to focus on water conservation to avoid losses of this vital element. They decided to demonstrate that all of the systems that used water (flow meters, pipes, pumping stations, lagoons, etc) were in good condition and that no evitable loses of this important resource occurred. A plan was proposed to conduct a “hydraulic assessment” of fluid flux and water speed at different points and courses at the mine, with the purpose of obtaining hard data to support, verify and correct the information provided online from specific instrumentation dedicated to those purposes. The final goal was to manage the water resource basin in a sustainable way, based on cross-checked information. The chosen points are representative of the processes present in the mine, such as recirculating water stations at different operating conditions and surface water courses, where the fresh water capture systems operate."

Jan 1, 2016

By V. S. Sastri, G. R. Doey, R. W. Revie

"Different forms of corrosion, the various corrosive environments encountered, the mining equipment subject to corrosion and the methods to control corrosion in the mining industry are briefly reviewed along with the savings that could be achieved by corrosion control. IntroductionCorrosive conditions in mines and metallurgical plants, lead to deterioration and wastage of equipment and of materials. The cost of corrosion in the mining industry can be significant, and measures to minimize corrosion must be taken to reduce this cost(l-3). Although the data in Table I are twenty years old they indicate the significance of corrosion costs in four industrialized countries. The costs of corrosion in the U.S. metallic ores sector and in the Canadian mining industry are presented in Tables 2 and 3, respectively. Significant savings in the mining industry can be achieved by using corrosion control methods. For example, corrosion in the Canadian mining industry in 1991 cost $1460 million of which $97 million was avoidable. Indirect costs of corrosion associated with plant shutdown, lowered efficiency of equipment and overdesign are additional to the direct costs cited here."

Jan 1, 1994

By F. Gaul, H. R. Manouchehri, A. Mosser

"Mining is a major energy intensive industry that contributes in consuming about 7% of the total world’s energy in which almost half in comminution. The underlying trait that drives energy consumption upwards appears to be somewhat persistent due to increasing in population, demands and growth rate. High grade resources have been/being depleted; consequently, low grade, high competent and complex ores with complicated geological structure are brought into perspective. For efficient extraction of values from such resources comprehensive multistage mining and processing strategies must be taken into account. Different treatment technologies, including ore sorting, must be considered to improve resource efficiency and productivity while taking into account the reduction in energy and water consumptions and related sustainability issues.The implementation of sorting technology in mining industry has a long past and its impacts on improving the overall efficiency of both mining and milling have been proven. However, the lack of complete understanding of its potential combined with ore complexity and low capacity of sorting machines have prevented the large scale application in mining industry. The application of X-Ray transmission sorting at Mittersill Tungsten Mine in Austria is presented and discussed herein. A technoeconomic analysis of the technology has revealed a significant potential of adding value to the concentration process. The rough feasibility study has given a strong feed-back on profitability and short time payback of about 2 years for the investment. Except the economic benefits the technology has positive environmental impacts. The potential for saving energy and water is large. The rough calculations have revealed that the energy saving can be up of 840MWh/annum. Furthermore, the ongoing cooperation between Mittersill mine and the sorting manufacturer is a good example on how the development of more competitive products, and product offerings, can be made."

Jan 1, 2016

By I. Stanoev, V. S. Stoilov, I. Gradinarov, E. D. Visariev, I. A. Bonchev, Aurubis Bulgaria

"Aurubis is the leading integrated copper group and the world’s largest copper recycler. In Copper smelter Aurubis Bulgaria (Pirdop), the residual copper in the slags from Flash furnace and Converters is recovered by flotation. The slag processing comprises: pit cooling, crushing, two stages grinding (autogenous and ball) and flotation. The copper concentrate is thickened and then is filtrated by vacuum disk filter. The thickener overflow is sent to settler for additional clarification. A resent throughput increase resulted in higher solid content in the thickener overflow due to insufficient thickener area. Different scenarios to overcome the issue were evaluated (new thickener, reagents and reconstruction). An increase of the thickening area by installation of lamella modules was chosen as the most promising option. Three lamella modules (1 m3 each) were installed in conventional thickener for the test. Number of sampling campaigns was done to evaluate the effect on solid content in overflow. Parameters of the dewatering cycle were collected during sampling campaign. The products grain size distribution was defined - thickener feed, thickener overflow with and without lamella. The thickener overflow with lamella modules has 2.12 g/L less solid content. The decrease was 71.8%. According to the tests results, the whole conventional thickener was reconstructed with lamella modules. The thickener area was increased by more than 400 m2.INTRODUCTIONIn Copper smelter Aurubis Bulgaria, the copper in slag from the Flash furnace and the Converters is recovered by flotation. The scheme of slag processing is crushing, two stage grinding (autogenous and ball) and flotation. Till 2010 the grinding cycle in the plant was in two stages: the first stage was AG Mill 70×23 working with a classifier and the second stage was ball mill 3.6/5.5 working with a hydrocyclone. In 2010 a new AG Mill 65×78 with hydrocyclone was put in operation in order to increase throughput of the plant. The second stage of the grinding cycle was not changed."

Jan 1, 2016

By N. Torres, G. Melcher

"An alternative to building new copper smelters, because of either stringent environmental regulations or in order to expand current plant capacity, could be achieved through the retrofitting of old reverberatory furnaces by making use of tonnage oxygen. The CONTOP® technology offers unique advantages over other techniques for this purpose, especially regarding substantial reduction in bath, capital and operating costs. This is possible to achieve since the reverb throughput could be largely increased with no major structural modifications to the furnace.The following options are offered to the smelter operators: dirty concentrates can be treated in an adjacent Contop system, or the cyclones can be mounted on the reverb roof for either dual operation or full Contop operation. ln the tatter case the furnace will be used as a settling chamber and f or slag c1eaning by top blowing with reducing gases.By incorporating Contop technology, the furnace throughput can be increased, higher malle grade, fixation of sulphur from furnace off-gas and substantial savings in energy consumption are possible to attain.IntroductionCopper smelting has been revolutionized during the last quarter century to such an extent that the standard type of plants consisting o f roasters and reverb furnaces seem a thing of the past, or almost. Though the building of new, more energy efficient smelters is a very likely opportunity for a grassroots plant, it would be hardly justifiable to replace an old existing plant unless there are heavy environmental or economic constraints(1,2,3)."

Jan 1, 1984

By A. G. Pronk, D. M. Burton

"A regional till sampling program in the Upsalquitch Forks-Tetagouche Lakes area, centred some 70km west of the city of Bathurst, has proven an effective method for gold exploration in the heavily glaciated interior of northern New Brunswick. Prospecting activities within this area over the past three years, have led to the discovery of several gold occurences associated with quartz-carbonate alteration in a variety of intrusive rock types emplaced along major fault zonesQuaternary mapping shows that the glacial history is complex. However, the displacement of material is uniform in distance and direction, and the till is generally thin (0.5 m to 2.0 m) and locally derived, making the interpretation of till geochemical patterns relatively simple for the explorationist. Previous studies have shown the the fin e-grained gold is best detected in the -250 mesh (-0.063 mm) till fraction (clay plus silt) and that the C-horizon is the preferred medium for analyses.Samples were collected on a 2 km grid and analyzed f or Cu, Pb, Zn, Au, Ag, As, Sb, Mn, Fe, Ni, Co, and Cd. Results indicate that concentrations of 10 to 20 ppb Au can effectively delineate areas of anomalous gold in bedrock associated with fault structures, and that a good potential for discoveries exists to the west of the known occurrences, where up to 678 ppb A u has been detected in tills. IntroductionThis paper reports on the result s of surficial geological investigations conducted over the past two field seasons in north-central New Brunswick. The stud y area is located in the Upsalquitch Forks-Tetagouche Lakes map area s (N.T.S. 21 0 19 and 21 0 (10) 70 km west of the city of Bathurst (Fig. I). The area is situated on the margin of the New Brunswick Highlands and has a maximum elevation of 640 m (for a detailed description of the physiography, see Rampton et al. 1984).Historically, exploration in northern New Brunswick has concentrated on base metals within the Cambro-Ordovician Tetagouche Group, resulting in the discovery of man y significant massive sulphide deposits (Brunswick No.6 and No. 12, Heath Steele, Caribou, Armstrong Brook, Orvan Brook, McMaster, Murray Brook, and Restigouche). Auriferous base metal occurrences along the Rocky Brook-Millstream Fault have also been previously investigated."

Jan 1, 1988

By L. Vollert

"The application of pneumatically-assisted fluidized bed flotation, specifically the ERIEZ HydroFloatTM technology, has found widespread use in non-sulphide processing (particularly phosphate, potash and coal) for the recovery of coarse particles. In gold processing, centrifugal gravity circuits and flash flotation cells are typically employed for the recovery of coarse and near-size liberated gold which tends to accumulate in recycled grinding streams due to bypass to the classifying cyclone underflow streams owing to the higher specific gravity of these gold particles. Early removal of this gold from the grinding circuits contributes toward the reduction of downstream processing losses as a result of overgrinding and particle shape deformation in the case of flotation processing, longer leach residence times in the case of extractive processing, and surface occlusions in the case of both flotation and extractive processing. Furthermore, recovery to bullion attracts higher payment terms by way of comparison to concentrate sales in the case of copper-gold concentrators. This paper assesses the application of pneumatically assisted fluidized bed flotation for the recovery of coarse liberated gold through the analysis of piloting data generated from the operation of a continuously operated 16 inch ERIEZ HydroFloatTM unit treating a sized coarse grinding circuit stream. The paper presents the stage recovery by size performance of the ERIEZ HydroFloatTM unit together with quantitative gold deportment analysis to demonstrate the efficiency with which gold was recovered during this pilot campaign and then compared to more conventional processing units – centrifugal gravity and conventional flotation.INTRODUCTION Newcrest Mining Limited (NML) has identified that an opportunity exists for improving the recovery of coarse composite particles at its current operations, both as a means for improving overall recovery and as an opportunity for early gangue rejection. As such, Newcrest Mining Limited has taken an interest in the application of pneumatically-assisted, fluidized-bed flotation i.e. ERIEZ HydroFloatTM technology. This interest dates back to 2011 with sighter testwork carried out on their Australian-held ore bodies (Kohmuench et al, 2013). Newcrest continues to assess ERIEZ HydroFloatTM potential for coarse composite recovery and, in the case of the topic of this paper, coarse gold recovery based on examples in the literature which demonstrate the efficiency of this technology in this regard (Carmona Franco et al., (2015); Miller et al., (2016); and Kohmuench et al, 2013)."

Jan 1, 2017