Search Documents

By A. A. Holland

Introduction The world's largest known deposits of natural sodium sulphate (Glauber salt), generally termed 'alkali ' throughout western Canada, are located in the Province of Saskatchewan: reserves are estimated to exceed 200,000,000 tons. These are surface deposits resulting from the recent or present-day natural evaporation of brines, in which respect they are similar to those occurring in certain other parts of the world, as in semi-arid sections of the United States, Russia, Germany and Austria. In some areas, underground deposits formed hundreds of thousands of years ago have been _encountered in drilling, and indications are that they also were formed under arid or semi-arid conditions. The master key to the formation of deposits of natural sodium sulphate, wherever they occur, is a climate, either past or present, under which evaporation exceeds precipitation over a considerable period of time. Commercial development of the Saskatchewan deposits began about thirty years ago. Previously, the demand for sodium sulphate had largely been met by salt cake produced as a by-product in the manufacture of hydrochloric acid from common salt. The rapid increase in the production of Kraft paper and, more recently, the development of synthetic detergent materials, have caused a marked increase in the market for sodium sulphate. This chemical gives the extra toughness to Kraft paper and is used in detergent compositions in proportions as high as 75 per cent. Saskatchewan now has six commercial plants producing natural sodium sulphate. Production from each in the fiscal years 1947 and 1948 is shown in Table I. The newest and latest plant is that of Saskatchewan Minerals, at Chaplin, which 1s designed to produce up to 150,000 tons of salt cake, 98.5 to 99.5 per cent pure, yearly. This is equivalent to about 24 percent of the total United States production of crude commercial salt cake for 1947.

Jan 1, 1949

By I. Westermann, K. Marthinsen, M. S. Remøe

"Al-Mg-Si alloys often add small additions of e.g. Mn or Cr, to form dispersoids, which may act as nucleation sites for Mg2Si particles after homogenization. The purpose is to ensure a high density of uniformly distributed small ?’-particles, which can be dissolved during further processing prior to the final age hardening step. However, their density and spatial distribution are critically dependent on the homogenization procedure. It is therefore important to have a robust and reliable method for assessing their spatial distribution. In the present work an existing methodology for assessing spatial uniformity, the Global Shannon Entropy (GSE), has been implemented and evaluated for different dispersoid structures characterized by scanning electron microscopy. This metric is highly dependent on the parameters used, but by careful selection of adequate parameters, it can be effective in detecting non-uniformity. An important weakness with the GSE was identified, and a modification to improve on the ability to differentiate degrees of non-uniformity is suggested. To evaluate the proposed methodology, the effect of heating rate on dispersoid precipitation behaviour during homogenisation of four Al-Mg-Si alloys with different Mn/Cr-content has been investigated. The metric with the new term has demonstrated promising results, and improved the ability to differentiate degrees of spatial uniformity.INTRODUCTION Al-Mg-Si series alloys are the most common aluminium extrusion alloys and are attractive for applications in a range of sectors (e.g. construction, automotive and recently also in consumer electronics), due to their generally good combination of strength, ductility and corrosion resistance. However, their extrudability and end properties depend critically on the alloy chemistry as well as prior processing conditions. Coarse ß-AlFeSi or Mg2Si-particles typically have a detrimental effect on extrudability, while small dispersoid particles may affect recrystallization, grain growth and precipitation of Mg and Si. The strengthening potential in the final age hardening step depends strongly on the amount of Mg and Si in solid solution after extrusion. The manner in which these particles are spatially distributed will decide whether the final product will exhibit uniform properties, and the number density and sizes will determine the extent of the effect. As such, these are important characteristics."

Jan 1, 2018

By R. Tervo, G. Ellie

"Automated information systems are being developed very rapidly in Europe. In France, Belgium and West Germany, more than 70% of the coal production is controlled by these installations. Information on both product ion and the mine environment is produced. For example, at one mine in France the system records the operating times of the compressors and of the refrigeration pumps, counts the number of coal cars passing the unloading point, and controls the principal conveyors and the loading /unloading of the storage bins. In addition, the ventilation air velocity, the methane content and the carbon monoxide content in the return air entry are recorded; an alarm is triggered and the current to the conveyors cut when the gas content exceeds a critical level. The recorded information is used at four levels: (1) for immediate action, (2) for daily reports, (3) for monthly reports and (4) for long-term studies. For example, when any conveyor is stopped for more than 10 minutes, the system controller immediately telephones to learn of the reason. At the end of a shift, the load factor of the conveyors is computed; then monthly an analysis of the causes of low load factors is made. The presentation describes in detail the system that has been installed in more than 20 mines in France."

Jan 1, 1973

By S. Nafisi

Permanent mould casting may be regarded as a near net shape manufacturing process where simple to very complex shaped engineering components are fabricated with high degree of precision in a metallic mould, In this group, High Pressure Die Casting (HPDC), have attracted more attention because of its production rate, where both liquid and semisolid metals (SSM) can be cast with high degree of precision and versatility. The SEED process, Swirled Enthalpy Equilibration Device, the new process for semi solid metals slurry production route, consists of two steps: The initial step involves extracting specified amount of heat from the molten metal to generate liquid-solid slurry, i.e, mushy structure, followed by drainage of remaining liquid to produce a compact free standing feedstock for rheocasting operation. In this paper, microstructural evolution during the process and some initial casting results of automotive components an also reported.

Jan 1, 2005

By D. M. Baird

ABSTRACT A revised stratigraphic section of Carboniferous rocks which occupy about 700 square miles in southwestern Newfoundland is presented. Gypsum, which outcrops at thirty-five different localities, is found to belong to four principal zones in the section. The newly mapped structure of the region makes the otherwise random occurrences of gypsum appear as systematic outcroppings of the four zones which follow the regional structure. Details of several occurrences are given and those most advantageous for exploitation are pointed out. INTRODUCTION ROCKS of Carboniferous age occupy an area of about 700 square miles in southwestern Newfoundland. They occur in a belt, from 5 to 15 miles wide, which extends from the head of St. Georges bay southwestward for 65 miles to the mouth of Little Codroy river (see Figure 1). Several hundred feet of Pennsylvanian rocks overlie rocks of Mississippian age, which are at least 12,000 feet thick. The rocks of the Carboniferous section of Newfoundland are very similar to those of Nova Scotia and represent a northeastward continuation of the same palaeophysiographic conditions. Mississippian measures of Windsor equivalence include thick gypsum deposits which outcrop at many places and which extend under large areas as indicated by sink-holes and by structural considerations.

Jan 1, 1951

By A. Brown

IN INTRODUCING the subject of rock pressures, it may safely be assumed that mining men are only too familiar with the physical effects of strata stresses that accompany the extraction of minerals. It may be further assumed that they have, as individuals, arrived at certain conclusions regarding their nature, based upon years spent in observing such phenomena and in learning how to continue mining in spite of them. Such hardly won experience forms the core of what is often referred to as 'pit sense'. This essential type of knowledge is not ?based on theoretical considerations, nor can it be found in text books. It is highly individualistic in nature and almost impossible to pass on from one generation to another in terms of precise rules for guidance. It is this aspect of individual judgment based on practical experience that has led to the significant phrase The Art of Mining.

Jan 1, 1956

By Imre Gombköto, Barnabás Csoke

"Raw material management means not only mining and processing of primary raw materials like ores, but means also collecting and processing secondary sources of raw materials. Recycling is one of the most developing field of raw material management in Europe, and its solutions are derived from mineral processing roots and principals. Complexity and challenges of the field of recycling results innovative solutions of material processing- Since European Union identified 20 raw materials as critical (CRM) due to lack of primary sources within the border of the EU, recycling become more recognised as source of different raw materials. WEEE is the waste streams contains many of the critical elements and along them at least 15 different species of plastics of which recycling is delayed by a lack of effective separation technique. Most paper deals with separation methods based on different specific gravity, triboelectric charge or surface properties of plastic species. Plastics however have differences of thermal properties and thermoplastics, duroplasts and elastomers can be recognised. The experiments described in the paper aimed to determine thermo adhesive behaviour of plastic species often identified in WEEE streams for separation purposes. According to the results, some plastic types as PS, PP. PC or PVC and PET pairs are possible to easily separate from each other, however different additives are changing thermo adhesive properties of most of the plastics that makes industrial process difficult to develop. Along thermo adhesive behaviour, combination of physical interaction can be used to enhance separation selectivity.INTRODUCTIONPlastics has a relatively long term of history as a light, multi-functional material in construction, packaging, automotive industry and electric and electronic products. There are a numerous types of plastic species can be used for various applications therefore they amount are growing from year to year. This quantity however become part of the waste stream and while metal recycling has been done for decades due to its economic value - cheap plastic parts are less desirable as secondary products. In 2013 an annual 5% of plastic production growth has been estimated with a base data of 265 million tonnes at 2010 (Guiqing & Zhenming, 2013). Since landfill requirements are increasing while—especially in Europe where actual regulations are trying to deflect waste from landfills - landfill capacities are decreasing, costs are become more and more expensive, Applications like energy production based on plastics as a fuel or recycling are some of the options can be applied. Direct incineration of plastics are applied at many plants - in most cases where waste consist of dangerous substances are incinerated because plastics high calorific value helps correct average mixture composition enable operators reaching high enough temperature for combined power and heat generation while most of substances—like PAH, PCB or dioxins—are destroyed. Another path is using low temperature reductive cracking due to pyrolysis process, however the chance having higher concentrate of carcinogen substances in the products are higher since it applies around 400°C during the process."

Jan 1, 2016

By L. C. Kitchener, K. Vollenwyoer

"This paper describes the development of an automated, 70-ton capacity, underground electric trolley truck at Inco Ltd. The purpose of the project is to provide a high capacity and high productivity haulage system to suit continuous loader applications in existing mining horizons where conveyor belt application is not immediately practical. IntroductionWith the start o f a program by Inco in mid-1983 to develop a continuous loader for bulk mining of our hardrock orebodies, the need for a rapid ore transportation system was recognized to match the increased extraction rates planned. Two methods were investigated, truck haulage and conveyor belt. As a result, a conveyor belt system has since been designed and installed with a continuous loader at Stobie Mine and an electric truck has been designed, fabricated and assembled, with shop testing underway. This paper deal s with the latter project. BackgroundMany existing mining horizons which could utilize continuous loaders do not have the straight runs required for conveyor belts. In these situations, truck haulage would be the only alternative of the other transportation methods that would be practical. In order to match the high productivity potential of the continuous loader, however, a more efficient trucking system is required than would be available with conventional diesel powered trucks or with electric truck designs commercially available, or under development. A higher capacity truck and an automated operation is necessary so that the application of additional units to suit increasing haulage distances matches loader output without reducing over-all productivity because of the need for additional operators.A first effort to work with a major electrical manufacturer was unsuccessful and resulted in a project delay of almost one year. In November 1984, an investigation into the concept was reinstigated with UTDC, and an agreement to start design was reached in April 1985."

Jan 1, 1988

By T. Holmes, S. Davison

"The Special Standard Surge bin at Agrium’s Vanscoy Potash Operations (VPO) has been plagued with flow problems and wear, and corrosion issues for it’s entire working life. Investigation showed that the carbon steel construction, bin geometry, and resultant funnel-flow pattern were directly responsible for production losses and disproportionate maintenance and capital costs. Potash enters this bin at between 140°C and 165°C, but the stagnant potash outside the active flow channel was much cooler, allowing moisture to migrate toward the outer regions, which caused corrosion of the walls and reduced live capacity as the potash in this area hardened and built up on the walls over time.A 2013 inspection revealed holes and paper-thin areas in the lower cylinder wall sections and in the conical hopper. The only thing preventing major leaks and even a potentially catastrophic failure was the buildup of stagnant hardened product on the cone walls. It was concluded that the cone had reached the end of its life and required replacement. VPO’s original plan was to replace the cone in kind and repair the cylinder as necessary; however, a failure-mode and bin-performance investigation combined with a lifecycle- cost analysis indicated it would be better to redesign the hopper.For success in retrofit projects, it is essential at the design stage to consider the bulk solid flow properties and the operating environment involved. Because education in this area is not offered at a university level, engineers often do not fully appreciate the effects of the flow properties of bulk solids on bulk material handling equipment.Jenike & Johanson conducted flow properties tests on samples of potash and using the data, redesigned the bin and the feeder. After the modifications, VPO’s surge bin provides safer, more reliable operation with a much longer predicted working life. Using this retrofit as an example, we aim to provide a general understanding of bulk solids flow theory and highlight the importance of customizing the design to the appropriate flow properties in the cost effectiveness, reliability, and safety of a bulk material handling system."

Jan 1, 2016

By J. L. Jambor, R. W. Boyle

"The Magnet Cove barite-sulphide deposit is a raking pipe-like body that replaced and partly filled a large brecciated zone at the junction of two faults at the contact between sedimentary rocks of the Horton and Windsor Groups of Mississippian age. The principal minerals in the deposit are siderite, barite, hematite, pyrite, marcasite, galena, sphalerite, chalcopyrite, tennantite, proustite, pearceite, acanthite and stromeyerite. The mineral assemblage and textural relationships indicate that the minerals were deposited from low-temperature solutions. The source of the elements in the deposit is believed to be the enclosing sedimentary rocks, with connate or ground waters as the transporting medium, and solubility products as the governing factor controlling the abundance and order of deposition of the minerals."

Jan 1, 1966

By A. K. Ratte, C. M. Brown

"IntroductionIn autogenous mills, grinding of the ore feed is accomplished by the direct action of the variously sized rocks making up the feed on each other and the mill interior. Size reduction is achieved without the addition of grinding media foreign to the mill feed, differing in this respect from rod, ball, and pebble milling. The term ""semi-autogenous"" has entered common usage in the industry to describe autogenous mills to which supplementary grinding ball additions are made to increase the rate at which size reduction of the mill feed occurs, beyond that achieved solely by the action of rock on rock. In a semi-autogenous grinding (SAG) mill, 50Jo to 10% of the mill volume may be occupied by grinding balls, whereas a range of 25% to 45% is more usual in ball milling.The comminution of mineral ores using ""conventional"" techniques has been described in previous papers. In conventional operations, size reduction of mined ore, and liberation of the valuable mineral content, is typically accomplished using flowsheets employing two to four stages of crushing. Crushing is followed by one to three stages of grinding and classification using various combinations of rod, ball, and pebble mills. This paper describes operations employing autogenous or semiautogenous grinding as the principal stage in the comminution process. Primary crusher discharge, or in some instances run of mine ore, is fed directly to an autogenous or semi-autogenous grinding circuit. Final product sizing may be accomplished in a single grinding stage, the mills operating in closed circuit with classification equipment, or in several stages using autogenous and semi-autogenous mills for primary grinding, and ball or pebble mills for secondary grinding. In several operations a portion of the primary mill discharge is crushed in an intermediate comminution step, these circuits being called autogenousball- crusher circuits (ABC). Many different flowsheets exist, but common and important to most are crushed ore stockpiles, reclaim feeder and mill feed conveyor systems, pumps, screens, and classifiers. Autogenous grinding is employed in both wet and dry processes, although today wet predominate."

Jan 1, 1989

By S. L. Gertsman

Canadian steel foundry practice has made marked progress during the past decade. Equipment suppliers, development engineers, and foundry personnel have focussed their attention on every phase of the foundry operation, with a resulting lower demand on manpower and materials. Also, more rigid specification requirements as to dimensional tolerances and quality have necessitated improvement and increased control at every stage from the pattern shop to the cleaning room. The growing trend toward mechanization is clearly evident. Equipment such as sand mixers, sand reclamation systems, material handling devices, moulding machines, core blowers, etc., is being increasingly employed by the steel foundryman. This equipment not only increases production but also tends to lessen the human variable so prevalent and disconcerting in the early days of steel founding. The result has been an improved and more reliable steel casting, which is gradually obtaining wider acceptance by design engineers. The purpose of this paper is to discuss briefly some of the practices being used, and also the direction of development that is being pursued by Canadian steel foundrymen.

Jan 1, 1948

By L. H. Van Loon, E. G. Crayston, A. F. Heather

"IntroductionTHE PROPERTY of Madsen Red Lake Gold Mines. Limited. comprises fifty-eight claims located between Russet and Faulkenham lakes in Baird and Heyson townships of the Patricia portion of the District of Kenora. The mine is seven miles •by road from the hamlet of Red Lake. This latter centre is .connected to the Trans-Canada Highway at Vermillion Bay, Ontario, by provincial highway No. 105 which has a total length of one hundred and thirteen miles.The Madsen property went into production on August 11th, 1938, with a milling plant rated at 300 tons per twenty-four hours. Changes made in the crushing plant during October, 1938, allowed a •finer feed to be delivered to the mill and increased the milling •capacity to 400 tons per twenty-four hours. During 1948, steps were taken to add an additional 400-ton capacity unit to the milling plant. This latter work was completed by May, 1949, giving the present total milling .capacity of 800 tons per twenty-four hours.It was realized in the early 1940's that, eventually, considerable material suitable for backfilling in the mine would be required. As there were no large deposits of gravel or sand anywhere near the mine, officials of the Company considered it advisable to investigate the feasibility of using mill tailings for mine •backfill. Since Madsen mill tailings contain approximately 80 per •cent of minus-200-mesh material, it was not considered practical to use them for underground backfill without first removing the finer material. as the slimes present in a product of this fineness would without doubt preclude any drainage whatsoever. Table I gives a sizing analysis of Madsen mill tailings and Table II a quantitative chemical analysis of the ore."

Jan 1, 1954

By R. Q. Honaker

A significant problem in ultrafine particle classification is the significant amount of submicron particle by-pass to the coarse particle stream. In classifying cyclones, submicron particle by-pass to the underflow stream can be reduced by decreasing water recovery. Past studies have shown that a reduction can be realized when the feed solids concentration is increased or the apex diameter is reduced. However, both adjustments tend to increase the particle size cut point and negatively affect classification efficiency due to the impact on slurry rheology. The addition of a viscosity modifier to the feed stream of a classifying cyclone improved the classification performance and decreased the particle size cut point over a range of feed solids concentrations. The detailed test program investigated the use of the modifier in conjunction with varying apex diameters to identify conditions that minimize ultrafine by-pass. With small apex sizes, roping conditions were readily eliminated by the addition of viscosity modifiers. The addition of the modifier had no deleterious effect on froth flotation performance, which commonly serves as a downstream separation process. The fundamental and practical benefits of viscosity modifiers in classification processes are discussed in this publication.

Jan 1, 2006

By R. D. Brown

In his March 31, 1977 budget, Finance Minister Macdonald has attempted the delicate balancing act of stimulating the economy without reinforcing the inflationary pressures which Canada is continuing to experience. Several tax changes of benefit to the mining industry, as well as measures designed to encourage oil exploration in frontier areas, are among the budget proposals. Additional earned depletion of 66- 2 /3 %, which may be offset against income from any source, will be available on drilling costs in excess of $5 million incurred between March 31, 1977 and April 1, 1980 in connection with an exploratory well in Canada, including the continental shelf . Other changes include more favourable treatment of resource property dispositions, less restrictive rules r elating to "successor corporations" , increased capital-cost allowance on railway spur lines, the inclusion of certain production royalties in Canadian development expenses and the application of the lower "manufacturing and processing" tax rate to sulphur production. To encourage business capital spending, the 5% federal investment tax credit it to be extended an additional three years to mid 1980 and broadened to include spending on scientific research and development. The rate of credit will also be selectively increased on a regional basis, to 7.5 % in certain designated areas in Saskatchewan, Manitoba. Northern. Ontario and Quebec, and to 10% in the Atlantic provinces and the Gaspe.

Jan 1, 1977

By I. R. Jonasson, R. W. Boyle

"Current interest in the distribution of mercury in the natural environment comes from quite different, though not unrelated, sources. Mercury has long been an important metal in many industries and has, therefore, been much sought after by mining interests. The presence of mercury traces in the various media of the natural environment, namely soil, rock, air, water and vegetation, is exploited by geochemists not only to find mercury and polymetallic ore deposits, but also to find most other types of economic metal mineralization. More recently, however, mercury has caught the attention of health authorities and environmental scientists who are becoming increasingly concerned over the hazards of mercury wastes and the danger these present to the environment and to man. It is now apparent that the trace quantities of mercury, considered so important and helpful to exploration geologists, can be concentrated in the biosphere to such levels as to present considerable problems for ecologists. This article summarizes most of the available data on mercury contents in materials of geological interest and presents average normal values for rocks, ores, minerals, soils, sediments, waters and plants. The geoch.emical cycle for mercury in nature is presented and the mechanisms of mercury migration around the cycle are discussed."

Jan 1, 1972

By L. H. Thorleifson

Demand for both gem and industrial diamonds is very strong. Synthetic production supplies industrial uses, but synthetic gems remain inferior and expensive, so the large gem market is supplied by mining. Several major mines have been depleted, and the market is receptive to new sources of high quality gems. Canada's Precambrian terrane, extending across the Canadian Shield and under the Phanerozoic cover of the Plains and Hudson Bay, has excellent potential for diamonds, but exploration conditions are difficult due to recent glaciation. Early world exploration relying on recognition of diamond in alluvial sediments was adequate to launch pre- 1900 production from India, Brazil, and Africa. Exploration success in Canada, as was the case in Russia and other more recently discovered sources, however, had to await large investments in effort supported by advanced science and technology. Canadian exploration in many ways is similar to that in other regions, relying on analysis of tectonics, indicator minerals, geophysical surveys, and multiple stages of drilling and sampling. Very different from other regions, however, is Canada's surficial environment, in which recent glaciation has caused fresh indicator minerals to be transported hundreds of km. Exploration accelerated in Canada after 1960, first in Ontario and the Arctic Islands, then in Saskatchewan in 1988, and most importantly after the Chuck Fipke - Stew Blusson discovery at Lac de Gras, Northwest Territories, in 1991 that led to the billion-dollar BHP - Dia Met Ekati Mine that opened in 1998. In 2003, production from Ekati will be supplemented by that from the similar and nearby Diavik Mine of Rio Tinto and Aber. These mines will bring Canadian output to over 10% of world supply, and will position Canada with Botswana and Russia as world leaders in production of high quality gem diamonds. There could be other mines as well, as sites across the Arctic and in the south from Alberta to Québec are being explored by an array of companies, including De Beers, other majors, and several juniors.

May 1, 2003

By N. Birbilis, S. Kairy, C. R. Hutchinson, D. Jiang, D. R. Feenstra, O. Gharbi

"Recent developments in metal-based additive manufacturing (AM) technology have generated considerable interest in multiple industries, owing to flexibility in design and the ability to produce final components in their net shape. The AM of high-strength aluminium alloys has not been widely explored, due to findings of undesirable microstructures leading to short fatigue life and poor fracture toughness; restricting the application of AM to lower strength aluminium alloys (with cast-like Al-alloy compositions) to date. Herein, aluminium alloy AA2024 (Al-3.6Cu-1.2Mg) was additively manufactured via selective laser melting (SLM), with the resultant microstructures and corrosion properties characterised and compared to wrought AA2024-T3. Microstructural characterisation was carried out using transmission electron microscopy (TEM), revealing SLM produced AA2024 included a population of ?-phase (Al2Cu) in preference to S-phase (Al2CuMg) typical of wrought AA2024. Additionally, the corrosion properties were investigated by potentiodynamic polarisation in a range of NaCl concentrations, whilst elemental corrosion rates were also determined (including for open circuit exposure conditions) and quantified in situ with an inductively coupled plasma mass spectrometer coupled with an electrochemical flow cell. Results revealed a significant improvement in the corrosion resistance, and elemental dissolution of AM prepared 2024 relative to wrought AA2024-T3.INTRODUCTION Aluminium alloys remain the preferred candidate materials in applications requiring a balance of low density and strength. The ability to produce net shape components from aluminium alloys has accelerated due to recent developments in metal-based additive manufacturing (AM) technology, including selective laser melting (SLM) and powder bed 3D printing. The AM of Al-alloys, including Al-Si-Mg (namely AlSi10Mg), has become widespread commercially in recent years. Alloys including AlSi10Mg offer reliable and reproducible production by AM, however such alloys (and variants thereof) are not high strength alloys. The pursuit of higher strength AM Al-alloys presents significant merit to multiple industries; however, such higher strength AM Al-alloys have not been widely studied to date. The solidification of high strength Al-alloys during conventional (casting) operations needs to be executed in a manner that avoids so-called =hot-tearing‘, which can arise as a result of the solute type and loading. A report on the solidification of a high strength Al-alloy prepared by AM, along with factors related to solidification, was recently covered by Pollock and co-workers (Martin et al., 2017). It was reported that AM of high-strength aluminium alloys (which have to date been principally based on the compositions of wrought high strength Al-alloys) may lead to undesirable microstructures that reduce fatigue life and result in poor fracture toughness; presently limiting the application of AM to lower strength aluminium alloys (with cast-like Al-alloy compositions) to date."

Jan 1, 2018

By W. H. Stheeman

"The high rock pressures at the deeper levels of the Tsumeb Mine have necessitated the changing of the mining methods and the introduction of cable bolts. After two rockfalls in the cable-bolted stopes, the mechanics of cable bolting were investigated. Practical methods were developed to find the best grout mixtures, the bond stresses between cables and cement, the bond stresses between rock and cement and the load on the cable bolts, which was mathematically calculated from data observed underground. The design of the cable bolt support system as used at the Tsumeb Mine is explained. GeneralThe Tsumeb Mine is in northern South West Africa/Namibia, approximately 400 km by road from the capital city, Windhoek, at an elevation of 1300 m above sea level. Mining operations in Tsumeb were started in 1905 by the Otavi Minen und Eisenbahn Gesellschaft and continued, with an interruption during the Depre ssion, until 1940, when the mine was closed and taken over by the Custodian of Enemy Property. The present owner, Tsumeb Corporation Limited, obtained the mine in 1947 and restarted the underground mining operations in 1949 after the mine was dewatered. Currently, the stoping operations are between 26 Level (840 m below surface) and 38 Level (1260 m below surface). In addition, the mine is an important silver producer and has produced 670,100 kg of silver since 1947."

Jan 1, 1982

By Z. D. Hora

"There has been a number of new developments in British Columbia's industrial minerals field over the past few years. Several new industrial operations were started to diversify the line of British Columbia mineral production by magnesite, perlite and fuller's earth. Industry activities and geological projects have identified occurrences of rare earth minerals, niobium, kaoline, fireclay and zeolites. The Geological Survey Branch significantly improved its database on industrial minerals. New geological concepts based on recent work are opening a number of new opportunities f or further industrial minerals' exploration and development in British Columbia.IntroductionTraditionally, the value of industrial minerals produced in British Columbia in any given year comprises between 100/0and 15% of the combined value of minerals, coal, petroleum and natural gas. Over the years a wide variety of industrial minerals has been produced , often with different levels of marketings success. For some products, such as dimension stone and clay or shale products, initial strong demand gradually dissipated; for others such as asbestos and magnesite, new discoveries or new industrial activities created demand and new markets . In some cases, such as fluorite , talc, pyrophyllite and perlite, wider use has been prevented by small size, poor quality or remote location of the deposits. Also, British Columbia , with 2.6 million inhabitant s, provides only a limited market and the industry therefore has to look beyond provincial borders."

Jan 1, 1990