Search Documents

By Sparrow G. J

In a recently completed AMIRA project, 20 samples were searched for gold mineralisation using the automated location facility (ALF) for rare phases on a scanning electron microscope in the CSIRO Division of Mineral Products, Melbourne. The samples were submitted by mining companies in Australia, and Papua New Guinea, and included crushed ore samples, cyclone overflow and underflow products, a flotation concentrate, and 12 tailing samples. Their gold contents ranged from 600 to 0.2 g/t An. Native gold and gold minerals including a gold telluride, gold-silver tellurides, and a gold bismuth mineral, were located in the samples as free grains and associated with other minerals such as pyrite, magnetite, hematite, ankerite, copper sulphides, silicate minerals, and quartz. In the highest grade samples, both micron sized and 200 ¦m grains of gold were found with ALF. It would be difficult to locate such d wide size range of gold in a manual search. Gold mineralisation was located in the tailing samples assaying 0.4 g/t An and higher. In several tailing samples coarse grains of native gold over 40 p.m in size were located. One grain was estimated to have contributed 40 per cent of the gold in the sample. As well as locating gold mineralisation, the ALF examination resulted in the identification of uranium, mercury, and bismuth minerals in the samples. Knowledge of the distribution of these minerals in processing streams could be important in the operation of a concentrator.

Jan 1, 1992

By Mackenzie J. M W

The mechanism of clay slime flocculation in coal washing circuits is considered and it is concluded that polymer flocculants are most suitable. It was found that the addition of sea water with a polymer flocculant improved flocculation and settling, and it was also found that dilution of a flocculated pulp increased floc size and hence settling rate.In predicting plant consumption of reagent it was found that cylinder tests, or even pilot plant tests, could give erroneous results, particularly on flocculated pulps. Different flocculants may, however, be compared in cylinder tests.For filtration, flocculation with Separan plus sea water was much more beneficial than flocculation with Separan alone.INTRODUCTIONDuring the mining of coal, and its subsequent beneficiation by washing, large quantities of minus 10 mesh material are produced. This fine material, which consists of broken down shales and fine coal, causes difficulties in water clarification circuits, in refuse disposal, and in filtration of fine coal.These difficulties can be largely overcome by flocculation, and this paper discusses the mechanism of flocculation, the methods by which a selection of flocculant may be made from the large number available, and the limitation of the prediction of plant performance from laboratory tests. This work applies particularly to the washeries of The Broken Hill Proprietary Co. Ltd. (B.H.P.) and Australian Iron and Steel Ltd. (A.I. & S.) .

Jan 1, 1962

By C R. Sundberg

Despite nearly a half-century of continuous production, the low-grade iron ore (taconite) deposits of North America remain economically competitive sources of raw materials for the domestic steel industry. The continued viability of these mature integrated mining-concentrationagglomeration complexes requires highly efficient utilisation of assets, especially the mineral resource. At Cleveland-CliffsÆ five North American managed operations, enhanced ore characterisation techniques are playing a critical role in their continued success. Due to the low-grade nature and complex mineralogical composition of these deposits, ore characterisation cannot solely rely on assay grades. Historically, taconite ore characterisation has augmented assay grades with bench-scale concentration tests to quantify recoverable mineral. The economic necessity for improvements in mill efficiencies and final product quality has mandated significantly greater knowledge of ore-related impacts. Cliffs Technology Center has met this challenge by developing a variety of novel iron ore characterisation techniques. The applications developed include both in situ and laboratory procedures, plus unconventional data integration methods uniquely suited for these deposits. This paper details the evolution of these novel ore characterisation techniques and their application to each phase of the operation: mining-concentrating-and pelletising. The improved ore characterisation techniques have contributed to successes at individual Cleveland-Cliffs managed operations including mineral recoveries exceeding 95 per cent and productivity increases exceeding ten per cent while consistently achieving customer product quality objectives.

Jan 1, 2002

The key elements required to maintain final wall integrity and hence slope reliability are discussed. Failure modes and mechanisms in highly structured rock slopes are then reviewed. The impact of blast disturbance on rock masses in general is discussed and the relationships between the slope failure mode and blast disturbance is then explored. The question of how designers can incorporate such impacts into the slope design process is then addressed. This necessarily involves rock mass strength consideration and two case studies are used to demonstrate a recent dilemma in this regard. Some progress regarding this dilemma has also been reported for the second case study. The major conclusions are that: Slope reliability can be severely compromised if the slopes are damaged by blasting and this impact is not often incorporated into the slope design process. The location and extent of the blast damage will impact some slope failure geometries and failure mechanisms more than others. The concept of failure mechanism specific vulnerability needs to be further developed. The evidence indicates that this aspect is even more extreme for weak ground conditions. The quantification of the reduction in rock mass strength due to blast damage is not well understood and limitations exist with some recent guidelines. The use of the Hoek-Brown criterion for slopes in blocky rock masses requires considerable judgement. Further applied developments in this regard would be very beneficial to the industry. Some promising methods to incorporate blast damage estimates into the slope design process are emerging. It is good business to minimise final wall blast damage otherwise a whole range of issues relating to reduced slope reliability emerge.

Jan 1, 1999

As a number of underground fires have unfortunately happened in the Broken Hill mining district, the writer trusts that a paper dealing with such a subject may prove of interest. To simplify matters, the subject is classed under three mainheadings- I Origin of fires; II Methods of subduing them; III Precautions to minimize the risk of their occurrence.Underground fires may be started in three ways - arson, spontaneous combustion, or carelessness.With regard to the first-mentioned cause, direct evidence is usually lacking to prove that any fire has been caused maliciously; Though definite proof of spontaneous combustion having been the cause of a mine fire has not been brought forward, nevertheless it should be considered, especially in the case of sulphide ore bodies of a more or less friable nature. The writer has been informed on reliable authority that in an open stope on the...

Jan 1, 1911

By D S. Stewart, K W. Keskimaki

In 1999, the Henderson Mine commissioned the Henderson 2000 project - a new truck haulage level, a new underground crusher and a 24 kilometre conveyor system to replace a 23-year old rail haulage system. Henderson has been able to continuously improve in almost all aspects of its rubber-tired mining. The rail haulage system represented one of the last barriers to continuous improvement to the overall plant performance. Many of the lessons learned in other areas of the mine were utilised to design the truck level. This paper chronicles the benchmarking, equipment selection and design of the level. Areas covered will include haulage trucks, level layout, ore chute design, traffic control, road design and crusher layout.

Jan 1, 2000

By Fletcher G

This paper will outline the design process, and the constmction and rehabilitation techniques proposed for the external waste dumps associated with the mining of the Wolfang Basin coal measures.The basin is located to the north of Clermont and immediately west of the Bowen Basin in Central Queensland, Australia. Development of the Clermont Coal Mine is planned for the mid-1990s after adequate sales commitments are obtained to allow the project to proceed.

Jan 1, 1992

By Wagland D. G, Guo H

The Mt Whaleback orebody is in a complex geological regime. A good understanding of geological structure is essential during the design and implementation stages. The amount of information on the rock-mass condition available at the design stage is considerably limited. It is essential to validate the rock-mass properties used in the design during implementation. It is important to achieve integrity of the final pit wall during development and to maintain the integrity until the end of its designed life for safe and economical extraction of ore. The original geological model is updated by way of on-going detailed geological face mapping. Original design is reassessed and is modified based on any significant variations to the previously evaluated geotechnical conditions. Information gathered during design implementation provide tools for effective management of the pit walls. Controlled blasting techniques are employed in the final limits blasting. Presplit blasting is used in most limits blasts. Presplit helps to maintain the integrity of the wall by venting excessive gases from the limits blast. This helps to reduce bedding dilation by gas penetration. Also, it helps to define the design batter for the operators for final batter trimming. Pyritic shale needs special attention during blasting due to its reacting nature. Cablebolting is applied in selective areas to secure small-scale potential instabilities. During the development phase, pit wall monitoring instruments are installed. These instruments are used to monitor the performance of the wall during and after excavation of the slope.

Jan 1, 1995

As near-surface underground mines progress deeper, the inevitable question is whether to convert from truck haulage to shaft hoisting. The desire to defer capital expenditure frequently delays investigation of the shaft option, or deferral of a decision to start shaft sinking, unless the shaft option is clearly significantly better than trucking. By the time increasing depth makes trucking uneconomic, there may then be insufficient resource remaining to justify a shaft, and the mine must close. However, had the shaft been built earlier, its lower operating costs would have permitted the mine to continue to greater depths. This paper presents a methodology for investigating the shaft versus trucks decision. As well as the typical analysis of which option is preferable at the time the analysis is conducted, the process presented illustrates how the timing of the decision to sink a shaft is critical. The paper shows how to identify the latest date at which the decision to sink a shaft can be made, after which time the shaft option will not be economic. It also illustrates how to assess the resource that may be required to justify the shaft. Considering this in conjunction with the latest decision date, implications for the companyÆs exploration program are discussed.

Jan 1, 2005

The fragmentation of whole rock by blasting has an influence on the subsequent loading, hauling and crushing operations. However, no method of calculating the frag- mentation has yet been developed. This paper gives a method of calculating the fragmen- tation for the simplest form of blasting, i.e. cratering. Cratering consists of the detonation of a spherical charge of explosive in a blasthole breaking to one free surface. This paper gives a method of calculating the extent of the system of radial cracks generated by the explosive in the rock. This system of radial cracks is then used to calculate the fragment size distribution curve from blasting. The calculated curves are shown to be in good agreement with experiment.

Jan 1, 1977

By Sandenbergh RF

The debate on the mechanism of adsorption of gold and silver di-cyanide onto activated carbon could be divided into two schools of thought. On the one hand, it has been proposed that the combined effects of electrostatic and chemical interaction between the activated carbon surface and adsorbing gold di-cyanide anion results in the adsorption of the latter. On the other hand the `ion-pair' adsorption reaction mechanism has been vigorously advocated as the dominant mechanism responsible for the adsorption of gold di-cyanide onto activated carbon. It is maintained that gold is adsorbed onto the carbon surface as the neutral ion-pair [M"+][Au(CN)z ]". Adsorption is viewed as the result of mainly the chemical interaction while electrostatic interactions are neglected. The validity of the `ion-pair' adsorption mechanism may be challenged on a number of counts. However, the alternative mechanism (based on aqueous surface chemistry principles) has not gained general acceptance yet, because it has not been applied widely enough to explain the different adsorption phenomena associated with gold di-cyanide on activated carbon. In the present study the case in favour of an adsorption mechanism based on general aqueous surface chemistry principles is presented. A model framework is developed for the adsorption reaction mechanism of gold di-cyanide onto activated carbon which incorporates the effects of chemical and electrostatic interactions between the dissolved species, the aqueous solution and the carbon surface. This model is then employed to explain a wide variety of reported adsorption phenomena for gold di-cyanide on activated carbon, such as the effects of pH, the adsorption of different metal cyano complexes, ionic strength, and type and concentration of cations in solution. In addition the effects of cyanide and dissolved oxygen concentration were investigated. No ready explanation, in terms of aqueous surface chemistry principles, is yet available for the switch in adsorption behaviour that agrees with ion exchange to ion-pair adsorption with increasing ionic strength.

Jan 1, 1997

By Rieniets S, Somerville J. L

In Morwell Open Cut brown coal mine, the overburden 'firehole' materials which have resulted from ancient coal fires vary-from hard baked clays to firm laminated lacustrine clays. The need to pre-strip designated areas to reduce the slope height and attain safe digging conditions for the bucket wheel excavator operation is now accepted practice at the open cut mine. In this study, the inherent spatial variability of undrained shear strength of the clay materials has been incorporated in a visco plastic, finite element based, probabilistic slope stability analysis. Data on the costs of initial pre-stripping, excavation and slope failure are collected to provide an economic basis for the optimisation of the design of the overburden batters in Morwell Open Cut. This improved stability modelling is enabling costly pre-stripping to be minimised while ensuring acceptable slope stability conditions and minimising the risk to personnel and plant.

Jan 1, 1994

Two ends of a longwall face are not only concentrated locations of equipment, but also provide ventilation and access. The roof strata stability here has an important influence on mining coal and safety. Based on field obser- vations in the gateways at Zaozhuang Colliery (Shandong Province) and model tests, the author developed a structural model of the overlying strata at the ends of the longwall face - the arc triangular cantilever plate - to which the elastic theory of plates can be applied. Factors influencing the stability of the cantilever plate and its breaking character- istics are discussed. Requirements and design parameters for supports at face ends are pro- posed, based on these factors.

Jan 1, 1986

By E Kozan

The paper presents new developments of the methodology of open pit coal production scheduling optimisation. They deal with the specific features of the exploitation of single coal seam and utilisation of truck-shovel and dragline systems. A production scheduling optimisation model is developed as a linear programming problem. The objective function maximises the net present value of the mining project under the technological constraints for meeting the demand function of the coal processing plant and effective utilisation of the available production equipment. Both principles of mine planning, coal quality optimisation and waste deferment are incorporated in the model. Results of a case study are provided to illustrate the applicability of the optimisation model.

Jan 1, 2003

Since its beginning, with the works of D. Krige and later, G. Matheron, geostatistics has been analyzing in detail the essential factors at play in ore reserves estimation problems, with the ever-present aim of an optimal use of the available information. Not only do the reserves depend on the geological in situ resources, they also require a correct appraisal of many technical and economical parameters. The objective of the present paper is to show how the method of technical parameterization of reserves, which is at the heart of the geostatistical approach, provides an extremely powerful and versatile tool for characterizing a mining project. After a review of the main properties of the technique, its use in the economic optimization of a project will be examined. Two examples from copper and gold deposits will be given.

Jan 1, 1987

Magnetic Separators have a wide application in dry separation processes, frequently in conjunction with High Tension Separation. Dry processes can frequently be superior to established processes in more commonplace mineral associations. A system of dynamics is postulated and the forces operating ar'e examined, together with a method of evaluating the effect of operating variables. Practical applications of these theories to obtain optimum results on an individual separator, and various separations using a laboratoryroll type separator are described.Practical Flowsheets are of two main types, the first consisting of a series of scalping operations, the second for rougher, cleaner, and scavenger operations with middling recirculation. Some common separation problems with certain mineral associations illustrate the need for different approaches for different mineral associations. A table of mineral separation characteristics is appended, from which amenability may be tentatively estimated.INTRODUCTIONMagnetic separators are widely used, either alone or in conjunction with other wet and dry concentration devices, for the upgrading of a variety of minerals. The high standards of efficiency attainable in dry mills, together with reduced operating and labour costs, are slowly becoming apparent in a wide variety of plants. The combination of wet and dry concentration plant familiar in beach sand mining is finding application for such processes as upgrading a crushed chromite product, and production of clean scheelite,cassiterite, and other concentrates. Other dry beneficiation processes (such as the high tension beneficiation of iron ore, and the benefiGiation of asbestos) avoid the use of wet processes completely.Dry separation processes are likely to be applied more widely as their possibilities become more generally known.

Jan 1, 1958

By Anderson DR, Tassell G

A major environmental impact study carried out in the sand dunes of eastern Cape York used image analysis of remotely sensed data to both select sites for ground investigation and categorise the different ecological units present. The approach adopted was particularly suited to the type of environment in question and allowed a high degree of quantification, at a high level of confidence, at costs several orders of magnitude less than conventional Methods.

Jan 1, 1987

In the last few years a number of mineral laboratories were established in Indonesia coinciding with the increase in gold exploration in the region. Prior to this, much of the analytical work was sent outside the country,however this is no longer neccessary.

Jan 1, 1990

By Jifan X, Yongyu W, Liangjing L

Shallow interception of groundwater is a special dewa- tering form in the specific geological and hydrogeological conditions. It has an economic and technical effect. The roof of the Fankou Lead-zinc deposit is the Hutianqun aquifer made up of the limestone of the upper Carboniferous system. - A "water-bearing basin" is surrounded by the aquifuge and the aquitard below ¦0 m level at the Shiling Hill section in the Hutianqun aquifer. Based on the natural conditions, an interception gallery is excavated at -40 m level out of "the water- bearing basin", the other gallery excavated at ¦0 m level in the poor water-bearing zone of the Jinxing Hill. During 20 years of experience, the better interception effects have been gained.

Jan 1, 1988

The mining industry views with the utmost concern, legislative or administrative action that inherently reduces the scope for exploration activity. Is there any basis for this concern in relation to Victoria? This paper will outline the role of the Department of Minerals and Energy and the main features of legislative provisions affecting exploration effort. The practical difficulties that confront the Department and explorers alike will be examined. The importance of industry representation to influence the direction that policy and legislative review might take, will be highlighted. Above all, the paper will establish that one essential duty of government is to ensure the provision of appropriate mining titles and security of tenure.

Jan 1, 1982