Search Documents

By R-H Yoon

The thin film pressure balance (TFPB) technique was used to measure the kinetics of thinning of single foam films and disjoining pressures in the presence of sodium dodecyl sulfate (SDS) and electrolyte (NaCl). The results were analysed in view of the Reynolds equation to determine the role of surface forces in film thinning. It was found that film thinning is controlled by surface forces at thicknesses below approximately 200 nm. It was also found that hydrophobic force plays an important role particularly at low SDS and NaCl concentrations. The values of the hydrophobic force constant (K232) estimated from the film thinning experiments were used to predict the disjoining pressure isotherm using the extended DLVO theory, which were found to be in excellent agreement with experiment. The TFPB technique was also used to measure the equilibrium thicknesses (He) of the foam films stabilised by a non-ionic surfactant, n-octanol, in the presence of NaCl. At a given ionic strength, He increased noticeably with increasing octanol concentration at very low concentrations. This observation suggests that hydrophobic force is at its maximum level in the absence of surfactant and decreases with increasing surfactant concentration. The results obtained with the single foam films were used to explain the stability of the three-dimensional foams.

Jan 1, 2005

By J Zhang, O Ostrovski, C Zhang D Cai, Q Wang

The conventional CaO-SiO2-based mould fluxes are not suitable for high-Al steel casting because of the strong reaction between silica in the flux and aluminium in the steel strand. In the process of casting of high-Al steel, flux composition changes; with the decrease of the silica concentration and increase of alumina. Knowledge and understanding of the effect of the Al2O3/SiO2 ratio on flux structure and properties are useful for flux design for the high Al-steel continuous casting. This paper investigated the effect of the Al2O3/SiO2 ratio on structure, viscosity, phase composition of fluxes quenched at different temperatures and heat transfer of CaO-Al2O3-SiO2-B2O3-Na2O-Li2OMgO- F fluxes. It was found that flux melting temperature increased with the increase in Al2O3/SiO2 ratio. Viscosity of the flux melts increased significantly with the increase of the Al2O3/SiO2 ratio from 0.7 to 1.2, reaching the maximum value, and then decreased with further increase of the Al2O3/SiO2 ratio. Raman spectroscopy analysis revealed that the change of the Al2O3/SiO2 ratio led to the change of aluminate and silicate structural units. The turning point for viscosity was attributed to the change in the degree of flux polymerisation. X-ray diffraction (XRD) analysis showed that increasing Al2O3/SiO2 ratio increased crystallisation tendency of the fluxes. Heat transfer measurement by infrared emitter technique (IET) revealed that increasing Al2O3/SiO2 ratio led to the decrease in heat flux which is correlated well with the increased crystallinity of the flux. The results suggested that the flux with Al2O3/SiO2 ratio 4.3 is the best candidate among the studied CaO-Al2O3-based mould fluxes for casting of high-Al steel.

Aug 21, 2024

By R Buerger, D Barrett, P Hodkiewicz

The Emily Ann nickel mine is owned and operated by LionOre Mining International Ltd. The deposit was discovered during 1997 and is blind, concealed beneath 25 m of transported cover and a further 100 m of unmineralised Archaean felsic rocks. Nickel sulfide mineralisation is hosted predominantly in strongly deformed, altered and metamorphosed Archaean komatiitic ultramafic rocks. Subordinate felsic-hosted, remobilised mineralisation is also present. Mining of ore commenced during late-2001. Since the early days of exploration drilling, through feasibility delineation drilling and subsequent mining, a geological model involving thrusting and folding of a komatiitic-hosted nickel sulfide deposit has been an evolving theme. Development of appropriate mine geology procedures, including detailed mapping, significantly increased the confidence of mine-site geology and engineering staff in the geological model and improved operational efficiencies during start-up. This also allowed the engineering and mining team to develop a tolerance for the large fluctuations in daily production grade, with an understanding that budgeted production targets, on a level-by-level basis, were achievable. This paper describes the development of the current interpretation of the deposit and emphasises the importance of a sound understanding of deposit geology. The direct benefits at Emily Ann included improvements in drill targeting, resource estimation and mine planning.

Jan 1, 2003

By D S. Stewart, K W. Keskimaki

The Henderson Mine has been utilising a continuous panel caving method to extract molybdenum ore since starting operation in 1976. In the past three decades since the mine was designed, many changes have taken place in underground technology as well as the general nature of the mining business. The impacts of larger scale underground equipment and automation are significant at Henderson and continue to reshape the nature of the enterprise. During the first years of operation in the 1970s, Henderson required almost 2000 employees to achieve full production, today only about 400 people are required to fully utilise the plantÆs capacity. The most recent change to the facility is the conversion from a rail haulage system to an underground crushing and conveying system that transports ore 25 km to the Henderson mill site. This change has required the introduction of large, rubber tired haulage trucks underground and the mining methods necessary to develop the large openings demanded by the trucks and underground crusher. The development of the underground crusher is also the first step to mining the final bottom horizon of the orebody. Along with this move comes an opportunity to almost triple the effectiveness of the mining effort, through higher draw columns and wider draw bell spacing. This final advancement to a totally trackless mine has positioned Henderson well for safe and efficient operation as it enters the 21st century.

Jan 1, 2000

Iron formation-hosted iron ore deposits account for the majority of current world iron ore production and consist of three classes: unenriched primary iron formation with typically 25 to 45 wt per cent Fe; martite-goethite ore formed by supergene processes, with abundant hydrous iron oxides containing 60 to 63 wt per cent Fe; and high-grade hematite ores thought to be of hypogene or metamorphic origin overprinted by subsequent supergene enrichment with 60 to 68 wt per cent Fe.Individual iron ore deposits range from a few millions of tonnes to over two billion tonnes at >64 wt per cent Fe, although most are within the range of 200 to 500 Mt. In the Hamersley Province of Western Australia, martite-goethite ores are largely developed in the Marra Mamba Iron Formation, although high (>0.08 per cent P) phosphorous mineralisation is also well developed in the stratigraphically higher Brockman Iron Formation. Whilst the vast majority of high-grade microplaty hematite ore is best developed in the Brockman Iron Formation, this paper provides the first textural evidence of locally significant microplaty hematite mineralisation in the Nammuldi Member of the Marra Mamba Iron Formation, in the Chichester Ranges at the Christmas Creek, Cloud Break and Mount Nicholas prospects. Petrographic studies have identified a high-grade Fe texture composed of nanometre scale plates of hematite in mineralised sections of primary microplaty hematite deposits in the Pilbara and elsewhere, well below the normal depth of weathering or dehydration. The population of nanometre to micrometre scale hematite plates is interpreted to represent various stages of nucleation, crystallisation and progressive growth of hematite from the primary ore-forming fluid in areas that were once iron-rich carbonates or silicates in the BIF.

Jan 1, 2005

The Wellington Dam catchment has high value water, agriculture and coal and power generating resources. These conflicting land uses are managed through consultation and regulation. The Wellington Dam catchment is unique in that the Collie Coal Basin is located almost to the edge of the dam and has coal mining and power generation as its primary land use. Currently the dam is only used for irrigation due to its high salinity. The State Government has committed to reduce the damÆs salt levels to below 600 mg/L by 2015 so that it can be considered for public drinking water supply. The coal industry in conjunction with the community and State Government has worked together to enhance the water quality within the Wellington Dam to maximise its value and use by using mine dewater for industry, diverting saline Collie River flows, providing environmental (social) flows and enhancing water quality of mine voids to encourage new industry to the Collie Region. Both surface and groundwater in the coal basin are generally fresh, whereas the salinity in the Collie River East Branch generally ranges between 3000 to 20 000 mg/L and 1700 to 10 000 mg/L in the South Branch. Mine dewatering is currently two to three times greater than the recharge to the coal basin. As a result, all mine dewater is sent to power stations in the area, with excess discharged into drainage lines which flow into the South Branch of the Collie River. To maintain environmental and social flows some groundwater is also pumped to the South and East Branches of the Collie River during summer months. Completed mine voids are used for recreation and options for aquaculture are promising. However, handback criteria are yet to be finalised.

Jan 1, 2006

By McConachy G. W, Wright J. V

During the 110 years since the discovery of the Broken Hill PbZnAg deposit six major mining companies have mined the ore body and explored the ore environment. Despite this activity, no new orebodies have been found at Broken Hill. The failure to discover large new resources cannot be attributed to a lack of activity because major companies have maintained substantial exploration commitments over many decades. This suggests that not only was a unique coincidence of conditions required to form the deposit but also that full recognition and definition of the critical parameters may not yet have been recognised. In an attempt to illuminate some of the more unusual and poorly studied characteristics of the ore environment some new areas of investigation are presented here which may contribute to understanding the ore deposit setting and focus exploration towards different and perhaps more productive targets. Sedimentological characteristics of the host succession of the Broken Hill deposit are apparently unique along the line of lode. An upward-coarsening megasequence reflected in the development of clastic psammites stratigraphically below the ore deposit is one important ingredient which has received little exploration focus. These psammites also host mineralisation and form part of a spectrum of quart-zrich rocks collectively referred to as gametiferous psammites, garnet quartzites and blue quartz lodes. Sedimentological data interpreted from outcrop, drill core and downhole geophysical well logs support a elastic origin for some of these rocks; an interpretation which is at variance with traditional interpretations favouring an exhalative origin. A clastic origin for many of the footwall psammites, and their close spatial association with the orebodies suggests their role in ore formation was important. It is interpreted as a critical part of the fluid flow architecture within the sedimentary basin, which focussed ore forming fluids into an unique environment favourable for trapping mineralisation. Detailed stratigraphic correlation near the deposit has also highlighted that quartzofeldspathic rocks (Potosi gneisses and lode pegmatites) have complex relationships with ore. Suites of stratabound quartzofeldspathic pegmatites have received limited study, but their distribution and voluminous development suggests they may be as important to ore formation as the psammitic lode rocks which host the orebodies. These associations are not in conflict with some recent ore forming models invoking deposition in a shallow water environments of deposition. The geochemistry of parts of the host sequence has been studied extensively in the past but this has not been merged with current stratigraphic subdivisions. A large drillhole data base now permits the geochemistry to be related to the sedimentary succession and reveals that a signature involving stratigraphic vectors best illustrated by changes in MnO, Na2O, Pb and Zn can be detected. This is interpreted to reflect sedimentary basin processes as opposed to a classical volcanic hydrothermal alteration pipe associated with seafloor venting. The stratigraphic setting together with characteristics of some of these poorly understood areas is discussed to emphasise that construction of sound models for exploration requires the total ore environment to be studied with attention directed to the geometry and setting of the full range of host rocks. Control of the greater portion of the line of lode by a single company, Pasminco Australia Limited, now permits disparate datasets and observations to be merged and presents new opportunities and encouragement for model refinement and exploration success.

Jan 1, 1993

By M Wortley, A Cantarutti, T Ozkocak

The estimation of the grinding mill charge weight is vital to ensure its efficient performance. Mill underloading or overloading can cause losses through decreased production or unplanned down time. Metso Minerals Process Technology Asia Pacific and South America (MMPT) has developed two systems for measuring mill load. The first is an acoustic system (SmartEarÖ) and the second is an online model-based charge estimation system. The aim of both systems is to facilitate better operation of grinding mills. SmartEarÖ performs analysis on an audio signal from the mill and allows each different frequency component to be viewed, analysed and used in process control for load estimation. By isolating different frequencies, SmartEarÖ can give an estimate of mill load. The online dynamic mill model uses measurable mill parameters (such as power) to predict the current total load. Kalman filtering can also be utilised to further increase the accuracy of the model. Both of MetsoÆs systems have been installed at BHP BillitonÆs Cannington mine to measure the load within their autogenous (AG) mill. In this paper, the methods of mill load estimation are reviewed and compared to the bearing pressure reading, which is the current method used by Cannington to control mill load. The redundant estimates of mill load provide increased confidence and consequently more robust grinding operation under a wide range of conditions.

Jan 1, 2008

By J E. Lynch

The Mt Leyshon gold deposit produced in excess of three million ounces of gold and considerable silver over a period of approximately 130 years. Most of this production occurred between 1987 and 2001. Mining commenced in 1872, however it was highly likely that Chinese miners were not only removing alluvial gold from the area but were also mining very rich æreefÆ gold. Records for early alluvial and hard rock mining do not exist, however gold production was probably considerable. In the early 1980s Marathon Petroleum (Australia) Ltd (MPAL) joint ventured into the Mt Leyshon area which had been held as a mining lease by Noranda Australia Ltd since 1968. Noranda at that time was concentrating its exploration effort on the Balcooma base metal prospect areas to the north of Charters Towers. In early 1982 MPALs parent company was taken over by US Steel. This led to an opportunity for MPALs Australian management to purchase all tenements and licences (except for coal, oil and gas) which were duly purchased for $US 1 million. At this time MPAL had a remarkable array of gold tenements (many of which were subsequently mined by other companies) and Mt Leyshon was considered to be the highlight. Early æseedÆ capital ($A 3.1 million) was raised with backers being the Bank of America, the NSW Government Superannuation Scheme, Westpac, private individuals and a Queensland grocery chain by the name of æJack the SlasherÆ.

Jan 1, 2004

Broken Hill South Limited's discovery of phosphate deposits in the northwest of Queensland in 1966 prompted intensive exploration which has proved phosphate rock in excess of 2,000 million tons at ten separate deposits. Systematic exploration for phosphate in Australia was initiated by the Company in 1964. Early in 1966, an investigation of oil wells in the Georgina Basin in the Northern Territory and Queensland revealed widespread anomalous phosphate in early Middle Cambrian Beetle Creek Formation and Thorntonia Lime- stone. Phosphorites recognised in oil wells in the southeastern part of the Basin, Queensland, led to the discovery of the Duchess deposits, Exploration of the Beetle Creek Formation since 1966 has disclosed nine other sizeable deposits north of Duchess around the eastern margin of the Basin. The Lady Annie and the adjoining Lady Jane deposits, by reason of their location, 160 miles south of the Gulf of Carpentaria, are expected to be the first to be brought into production. Beneficiation testing and engineering investigations commenced in 1967. Transport between the deposits and various port sites in the Gulf of Carpentaria has been extensively studied and a slurry pipeline as a means of transport to a deep water island port, is now being investigated.

Jan 1, 1971

Coal is of tremendous importance for the Czechoslovak econ- omy. The current annual primary energy demand being about 109 million tons of standard fuel (1 ton of standard fuel - 7,000 coal = 29,308 GJ), coal satisfies almost two thirds of our fuel consumption. If compared with the distribution of resources in the world's fuel and energy pattern, the situation in Czechos- lovakia is significantly different, as shown in Fig. I. One of the causes behind the difference is that the Czechoslo- vak oil and natural gas reserves and, hence, their production are insignificant, so that it is necessary to import them. Brown coal will continue to play an important role as a prin- cipal domestic source of primary energy even in the future. While the share of nuclear power is increasing, brown coal represents strategic reserves in the fuel and energy balance.

Jan 1, 1989

The disadvantages of the present zinc producing methods, RLE and ISP, are high energy consumption and environmental problems. Therefore, efforts have been directed in Outokumpu Zinc towards the development of alternate routes. One interesting pyrometallurgical process to produce zinc is to inject zinc calcine together with a solid reductant into molten iron, saturated with carbon. This process has been studied by thermodynamic calculations, laboratory tests and mini-pilot test runs at Outokumpu Research Oy, Pori, Finland. The results of these tests are presented and discussed in this paper. The mini-pilot tests demonstrated that over 97 per cent evaporation of the zinc was possible using a reactive coal dust as the reducing agent. The recovery of zinc in the metal phase was at best 88 per cent of input zinc, but only part reported in molten lead in the splash condenser. The final metallic zinc contained at best 98 per cent Zn, the main impurities being dissolved lead and coal carried along with the flue dusts.

Jan 1, 1993

By Mitchell D. S

BackgroundIn March 1990 Pasminco resolved to replace and increase the capacity of the underground pumping system at the Southern Operations, Broken Hill. The existing pump station was built 23 years ago while the rising main had been in service for 38 years and was subject to frequent failure.The old system was a conventional slurry/clear water separation and multi-stage pumping system. It was inadequate in the following areas:ò insufficient capacity to handle current and expected future flows;ò unable to consistently dewater lower production areas; ò pumping capacity restricted sandfilling rates;ò dirty water dams had insufficient settling capacity and were difficult to de-sludge;ò the operating costs of dewatering were high; ò it was labour intensive; andò it did not offer enough protection to the 25 level loading station.

Jan 1, 1993

By M Dixon, T OÆShannessy

Melbourne Water (MW) is responsible for a section of existing gravity trunk sewer servicing the Melbourne central business district, Docklands, Port Melbourne and other adjacent areas, known as the Melbourne Main Sewer (MMS). MW has determined that the 2.2 km long 110 year old sewer will not adequately service these areas into the future or provide the level of reliability needed. The Melbourne Main Sewer Replacement project (MMSR) involves the replacement of the MMS with a new gravity sewer main and six key manhole shafts, known as the Melbourne Main Reliever (MMR).The majority of the MMR sewer tunnel is situated south of the Yarra River and will be constructed using an earth pressure balance (EPB) tunnel boring machine (TBM) and will be lined with precast concrete segments. The tunnel will be 2.4 m internal diameter and will have a 1.8 m diameter glass fibre reinforced plastic (GRP) sewer pipe positioned within it. This project represents the first large-scale, modern, mechanised tunnel project in MelbourneÆs Yarra Delta Quaternary sediments. There is little precedence known to the authors of similar scale tunnelling projects in these particular geological units. During the recent detailed investigation and design stages of the project, significant effort has been spent on characterising the geotechnical conditions along the alignment and predicting the effects of the new tunnel on the existing environment. Some of the key design issues that have been identified and managed through the design process include short-term surface settlement due to tunnel excavation and the predicted effects on surface infrastructure, potential spalling of the steel fibre reinforced concrete segments under full TBM ram loads and tunnel lining design in geological units with highly variable stiffness.Construction of the new MMR sewer tunnel is expected to commence in mid-2008 with a capital cost of approximately $160 million. Sewer system commissioning is scheduled for completion by early 2012.

Jan 1, 2008

By I F. Wood

Planning for flooding and assessment of flood impacts are important requirements for mining projects, as they are also for other types of development. With more intense development and concern from the community, supported by government regulatory requirements, assessment of flood concerns and impacts has become of increasing importance. To ensure that flooding issues are fully understood and results presented in an appropriate format, advanced hydraulic analysis procedures have been developed and are beginning to be applied. These procedures must be rigorous in an engineering context but the results must also be readily understood by the community and government agencies. Advanced two-dimensional hydraulic modelling is becoming accepted as an important means of assessing flooding issues for mining projects. With presentation of results from hydraulic models with Geographic Information Systems (GIS), flood impacts can be analysed rigorously and presented clearly. This paper discusses the application of advanced hydraulic modelling in the planning and impact assessment of a major mining project located on a floodplain where there is extensive inundation. The analysis provides for both input to the planning of the project and for detailed assessment of potential impacts. This case study illustrates some important aspects of the application of hydraulic modelling using a two-dimensional modelling to a critical flood design.

Jan 1, 2003

By D Wallace, H Guo, B Shen

Appropriate management of the ground subsidence induced by coal mining activities is essential. To assess the effectiveness of grout injection for mining subsidence control, time-lapse ground penetrating radar (GPR) imaging data were collected before and after grouting. The pregouting subsurface responses were interpreted to have changed after grout injection. The changes were caused by injecting the grout materials (flyash and water) into the delaminated strata and permeable fracture zones. The largest distance of the observed GPR event changes at the right end of the main profile is 132 m away from the injection borehole. Although the GPR images could not easily tell if the image changes were caused by the injected ashes or the water, it does suggest that the injection materials had been pushed at least 130 m away from the injection borehole. This is consistent with the borehole scan monitoring, which confirmed that the grout has travelled more than 90 m from the injection borehole.

Jan 1, 2006

The Middleback Ranges are a series of parallel northsouth ridges on the eastern side of the Eyre Peninsula, South Australia, about 20 miles inland from the Spencer Gulf, as shown in Fig. 1. They extend for some 20 miles across the centre of the County of York. North of them, on the same line of strike, in, the County of Manchester, is a disconnected series of lesser which ends in the Iron Monarch-Iron Knob ridge, the principal iron ore locality. These ridges are referred to in the following pages as an integral part of the Middleback Ranges.The deposits of hematite which outcrop in these ranges (Fig. 1) form the most important group of iron ore bodies in Australia, and are exploited by the Broken Hill Proprietary Company. The largest of them is the Iron Monarch (Fig. 6) .H: The next largest are the Iron Duke, the Iron Prince and Iron Baron. The Iron Knob, Iron Duchess, the North and South Iron Knights, Iron Queen, and the small body south of it, the Kimba Lease, and the deposits in the Cook's and Ash Leases, are all smaller.Numerous small lens-like bodies of hematite occur throughout the ridges, but are not of sufficient size to be of commercial use. At present only the Iron Monarch and the Iron Prince bodies are being worked. The Iron Knob was quarried previously, but its remaining supply is held in reserve.*Published by permission of the Council for Scientific and Industrial Research.

Jan 1, 1936

By Kikuta K

ISP (Imperial Smelting Process) produces zinc and lead simultaneously from zinc and lead sulphide concentrates and recovers copper and precious metals into a lead bullion. The strength of sinter is important to keep permeability in the shaft of the Imperial Smleting Furnace. The residual sulphur content of the sinter is also important as it causes metal losses into slag. The paper describes an investigation into the sintering operations to improve sulphur elimination and sinter strength. The micro structure of the sinter and the effect of the blast rate, sintering temperature etc have been studied.

Jan 1, 1993

Atlas Copco is one of the worldÆs leading providers of industrial productivity solutions (Atlas Copco, 2009). Furthermore, the company spans 160 markets and held 34 000 employees at the end of 2008. The company is organised under three ætechniquesÆ whereby the Construction and Mining TechniqueÆs business division is located within +rebro, Sweden. This paper is aimed at briefly facilitating information on how the company and more specifically, the Construction and Mining Technique is run. Also, by sharing my experiences, this paper is intended to encourage and motivate students currently studying for a degree relevant to the minerals industry, to apply for this extremely beneficial scholarship. Through a number of presentations relating to the various divisions, products and aftermarket services of the company, I came to realise that Atlas Copco extends beyond simply selling equipment suitable for the mining and civil industries. This tour through Sweden also contained highlights of visiting the Underground Rock Excavation factory, Surface Drilling Equipment factory and Secoroc divisions. I was also fortunate enough to participate in a tour of the LKAB mine in Kiruna. In addition, time was allocated to less industry related activities, and I was able to go dog sledging, sip vodka cocktails out of ice glasses at the Ice Hotel and enjoy traditional Swedish foods of moose and reindeer. Most important and memorable to me; however, was the ability for employees of Atlas Copco to speak of the company and their products with such passion and enthusiasm, which truly made this a motivational and unforgettable experience.

Jan 1, 2009

By T C. McCuaig, D B. Mapleson

The Wannaway Deposit is a structurally modified komatiite-hosted nickel-sulfide deposit. Until recently, nickel sulfide accumulations surrounding the Widgiemooltha Dome had been studied with a focus on understanding volcanological aspects of komatiite flow regimes and nickel-sulfide accumulation. Although volcanological features can be observed at Wannaway they are overprinted by several generations of structures associated with multi-phase deformation of the Dome. On the mine scale, two significant deformational events can be distinguished that control ore distribution. The first deformational event is represented by the formation of a layer parallel foliation within the footwall metabasalt and boudinaging of the ore into two distinct orebodies (mega boudins) during a north-south compressional event. Evidence of a second compressional event (east-northeast-south-southwest) is defined by reverse > dextral thrust-folding of the ore zone. The latter deformational event focussed the sulfide ore into thrust front positions where folded ore sequences are mined with stope widths up to nine metres wide. Later stage compressional and extensional deformation phases are observed but have minor, localised effects on the geometry of the ore zone. Four orders of control on the geometry and distribution of ore are interpreted through a combination of primary and secondary features observed at Wannaway. Extending the structural aspects of the secondary overprint features into areas of potential mineralisation has not only defined targets for extensions to the Wannaway Deposit, but has also aided to delineate high grade mineralisation and aid mining decisions. Obtaining an understanding of the volcanological conditions of formation, and more importantly, the structural evolution of the Wannaway region has been an integral part in optimising production.

Jan 1, 2003